Remove the ixdp2x01 cs89x0 hack from ixp2000's io implementation.
Since the cs89x0 driver has been made properly aware of the odd way
the cs89x0 is hooked up on the ixdp2x01, we don't need this hack
anymore.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Deepak Saxena <dsaxena@plexity.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rod Whitby [Wed, 4 Jan 2006 17:17:13 +0000 (17:17 +0000)]
[ARM] 3218/1: PAGE_SHIFT undeclared in arch-ixp4xx/memory.h (adjust_zones moved out of line)
Patch from Rod Whitby
PAGE_SHIFT is undeclared in include/asm-arm/arch-ixp4xx/memory.h, identified by the following kernel compilation error:
CC [M] sound/core/memory.o
In file included from include/asm/memory.h:27,
from include/asm/io.h:28,
from sound/core/memory.c:24:
include/asm/arch/memory.h: In function `__arch_adjust_zones':
include/asm/arch/memory.h:28: error: `PAGE_SHIFT' undeclared (first use
in this function)
This patch replaces my previous attempt at fixing this problem (Patch 3214/1) and is based on the following feedback:
Russell King wrote:
> The error you see came up on SA1100. The best solution was to move
> the __arch_adjust_zones() function out of line. I suggest ixp4xx
> does the same.
I have moved the function out of line into arch/arm/mach-ixp4xx/common-pci.c as suggested.
Signed-off-by: Rod Whitby <rod@whitby.id.au> Signed-off-by: Deepak Saxena <dsaxena@plexity.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rod Whitby [Wed, 4 Jan 2006 17:17:11 +0000 (17:17 +0000)]
[ARM] 3215/1: Iomega NAS 100d (MACH_NAS100D) machine support
Patch from Rod Whitby
This patch adds support for a new arm/ixp4xx machine - the Iomega NAS 100d network attached storage product. The NAS100D is a consumer device containing a 266MHz Intel IXP420 processor, 16MB of flash, 64MB of RAM, a 160Gb internal IDE hard disk, and 802.11b/g wireless on an Atheros mini-PCI card.
Work on porting the latest 2.6.x kernel to this device is being done by
the NSLU2-Linux project (the same team who maintains the port to the
Linksys NSLU2 device). In particular, the majority of this patch was
authored by Alessandro Zummo, based on the work done for MACH_NSLU2
support by the NSLU2-Linux core team of developers.
MACH_NAS100D (as implemented by this patch) can be enabled in jumbo
ixp4xx kernels without any affect on the other machines supported by
that kernel.
This patch applies cleanly against 2.6.15-rc7 and should be trivial to
apply to later kernel versions. It does not depend upon any other
patches.
Signed-off-by: Rod Whitby <rod@whitby.id.au> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Deepak Saxena [Wed, 4 Jan 2006 17:17:10 +0000 (17:17 +0000)]
[ARM] 3192/1: Remove gpio_isr_line_clear() API from IXP4xx
Patch from Deepak Saxena
Other than interrupt masking purposes, this API is only used when
configuring interrupt lines and this patch moves that functionality
directly into the ixp4xx_set_irq_type() implementation as board level
PCI code should not need to worry about those details.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 4 Jan 2006 15:51:51 +0000 (15:51 +0000)]
[ARM] Remove definition of MAX_DMA_CHANNELS to zero
Since we now only build arch/arm/kernel/dma.c on machine types
which set ISA_DMA_API, we don't need to define MAX_DMA_CHANNELS
to 0 to indicate this - this definition becomes superfluous.
Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Wed, 4 Jan 2006 15:08:30 +0000 (15:08 +0000)]
[ARM] Remove '__address' from scatterlist and convert to DMA API
The old __address element in struct scatterlist remained from older
kernels because the ARM DMA emulation code made use of it. Move
this field into struct dma_struct, and convert DMA emulation code
to setup a SG entry as required.
Also, convert DMA emulation code to use the new DMA API rather
than the PCI DMA API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 3 Jan 2006 18:41:37 +0000 (18:41 +0000)]
[ARM] Remove clk_use()/clk_unuse()
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 3 Jan 2006 17:39:34 +0000 (17:39 +0000)]
[ARM] Cleanup ARM includes
arch/arm/kernel/entry-armv.S has contained a comment suggesting
that asm/hardware.h and asm/arch/irqs.h should be moved into the
asm/arch/entry-macro.S include. So move the includes to these
two files as required.
Add missing includes (asm/hardware.h, asm/io.h) to asm/arch/system.h
includes which use those facilities, and remove asm/io.h from
kernel/process.c.
Remove other unnecessary includes from arch/arm/kernel, arch/arm/mm
and arch/arm/mach-footbridge.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Tue, 3 Jan 2006 17:28:33 +0000 (17:28 +0000)]
[ARM] Make kernel link address depend on PAGE_OFFSET
We are coding the kernel link address into the makefiles, which is
invisibly dependent on PAGE_OFFSET. If PAGE_OFFSET is changed, the
makefiles also need to be changed.
Make adjustments such that the makefiles encode just the offset from
PAGE_OFFSET for the kernel link address, and use PAGE_OFFSET in the
linker scripts directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
However, asm/param.h is sometimes used in userland (it is included
indirectly from <sys/param.h>), so your commit pollutes the userland
namespace with tons of CONFIG_FOO macros. This greatly confuses
software packages (such as BusyBox) which use CONFIG_FOO macros
themselves to control the inclusion of optional features.
After a short exchange, Christoph approved this patch
Some G5s still occasionally experience shutdowns due to overtemp
conditions despite the recent fix. After analyzing logs from such
machines, it appears that the overtemp code is a bit too quick at
shutting the machine down when reaching the critical temperature (tmax +
8) and doesn't leave the fan enough time to actually cool it down. This
happens if the temperature of a CPU suddenly rises too high in a very
short period of time, or occasionally on boot (that is the CPUs are
already overtemp by the time the driver loads).
This patches makes the code a bit more relaxed, leaving a few seconds to
the fans to do their job before kicking the machine shutown.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Sun, 1 Jan 2006 01:00:29 +0000 (17:00 -0800)]
sysctl: make sure to terminate strings with a NUL
This is a slightly more complete fix for the previous minimal sysctl
string fix. It always terminates the returned string with a NUL, even
if the full result wouldn't fit in the user-supplied buffer.
The returned length is the full untruncated length, so that you can
tell when truncation has occurred.
Yi Yang [Fri, 30 Dec 2005 08:37:10 +0000 (16:37 +0800)]
[PATCH] Fix false old value return of sysctl
For the sysctl syscall, if the user wants to get the old value of a
sysctl entry and set a new value for it in the same syscall, the old
value is always overwritten by the new value if the sysctl entry is of
string type and if the user sets its strategy to sysctl_string. This
issue lies in the strategy being run twice if the strategy is set to
sysctl_string, the general strategy sysctl_string always returns 0 if
success.
Such strategy routines as sysctl_jiffies and sysctl_jiffies_ms return 1
because they do read and write for the sysctl entry.
The strategy routine sysctl_string return 0 although it actually read
and write the sysctl entry.
According to my analysis, if a strategy routine do read and write, it
should return 1, if it just does some necessary check but not read and
write, it should return 0, for example sysctl_intvec.
Signed-off-by: Yi Yang <yang.y.yi@gmail.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Sat, 31 Dec 2005 01:18:53 +0000 (17:18 -0800)]
sysctl: don't overflow the user-supplied buffer with '\0'
If the string was too long to fit in the user-supplied buffer,
the sysctl layer would zero-terminate it by writing past the
end of the buffer. Don't do that.
Linus Torvalds [Fri, 30 Dec 2005 16:39:10 +0000 (08:39 -0800)]
Insanity avoidance in /proc
The old /proc interfaces were never updated to use loff_t, and are just
generally broken. Now, we should be using the seq_file interface for
all of the proc files, but converting the legacy functions is more work
than most people care for and has little upside..
But at least we can make the non-LFS rules explicit, rather than just
insanely wrapping the offset or something.
Erik Hovland [Fri, 30 Dec 2005 15:57:35 +0000 (15:57 +0000)]
[ARM] 3216/1: indent and typo in drivers/serial/pxa.c
Patch from Erik Hovland
This patch provides two changes. An indent is supplied for an if/else clause so that it is more readable. An acronym is incorrectly typed as UER when it should be IER.
Signed-off-by: Erik Hovland <erik@hovland.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jean Delvare [Thu, 29 Dec 2005 21:07:30 +0000 (22:07 +0100)]
[PATCH] Simplify the VIDEO_SAA7134_OSS Kconfig dependency line
Thanks to Roman Zippel for the suggestion.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
[ Short explanation: Kconfig uses ternary math: n/m/y, and !m is m ] Signed-off-by: Linus Torvalds <torvalds@osdl.org>
that changed the GART VM start offset. It fixed some machines, but
seems to continually interact badly with some X versions.
Quoth Ben Herrenschmidt:
"So I think at this point, the best is that we keep the old bogus code
that at least is consistent with the bug in the server. I'm working on a
big patch to X that reworks the memory map stuff completely and fixes
those issues on the server side, I'll do a DRM patch matching this X fix
as well so that the memory map is only ever set in one place and with
what I hope is a correct algorithm..."
Anton Blanchard [Wed, 28 Dec 2005 23:46:29 +0000 (10:46 +1100)]
[PATCH] ppc64: htab_initialize_secondary cannot be marked __init
Sonny has noticed hotplug CPU on ppc64 is broken in 2.6.15-*. One of the
problems is that htab_initialize_secondary is called when a cpu is being
brought up, but it is marked __init.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Jones [Thu, 29 Dec 2005 01:01:04 +0000 (20:01 -0500)]
[PATCH] fix ia64 compile failure with gcc4.1
__get_unaligned creates a typeof the var its passed, and writes to it,
which on gcc4.1, spits out the following error:
drivers/char/vc_screen.c: In function 'vcs_write':
drivers/char/vc_screen.c:422: error: assignment of read-only variable 'val'
Signed-off-by: Dave Jones <davej@redhat.com>
[ The "right" fix would be to try to fix <asm-generic/unaligned.h>
but that's hard to do with the tools gcc gives us. So this
simpler patch is preferable -- Linus ] Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: fix compilation with CONFIG_MODE_TT disabled
Fix UML compilation when SKAS mode is disabled. Indeed, we were compiling
SKAS-only object files, which failed due to some SKAS-only headers being
excluded from the search path.
Thanks to the bug report from Pekka J Enberg.
Acked-by: Pekka J Enberg <penberg (at) cs ! helsinki ! fi> Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] Hostfs: update for new glibc - add missing symbol exports
Today, when compiling UML, I got warnings for two used unexported symbols:
readdir64 and truncate64. Indeed, my glibc headers are aliasing readdir to
readdir64 and truncate to truncate64 (and so on).
I'm then adding additional exports. Since I've no idea if the symbols where
always provided in the supported glibc's, I've added weak definitions too.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: hostfs - fix possible PAGE_CACHE_SHIFT overflows
Prevent page->index << PAGE_CACHE_SHIFT from overflowing.
There is a casting there, but was added without care, so it's at the wrong
place. Note the extra parens around the shift - "+" is higher precedence than
"<<", leading to a GCC warning which saved all us.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trivial removal of unused variable from this file - doesn't even change the
generated assembly code, in fact (gcc should trigger a warning for unused value
here).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't use printk() where "current_thread_info()" is crap.
Until when we switch to running on init_stack, current_thread_info() evaluates
to crap. Printk uses "current" at times (in detail, ¤t is evaluated with
CONFIG_DEBUG_SPINLOCK to check the spinlock owner task).
And this leads to random segmentation faults.
Exactly, what happens is that ¤t = *(current_thread_info()), i.e. round
down $esp and dereference the value. I.e. access the stack below $esp, which
causes SIGSEGV on a VM_GROWSDOWN vma (see arch/i386/mm/fault.c).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David S. Miller [Wed, 28 Dec 2005 21:27:04 +0000 (13:27 -0800)]
[SERMOUSE]: Sun mice speak 5-byte protocol too.
Noticed by Christophe Zimmerman, this explains the slow mouse movement
with 2.6.x kernels.
And checking the 2.4.x drivers/sbus/char/sunmouse.c driver shows we
always used a 5-byte protocol with Sun mice in the past. I have no
idea how the 3-byte thing got into the 2.6.x driver, but it's surely
wrong.
Signed-off-by: David S. Miller <davem@davemloft.net>
Chris Elmquist [Tue, 20 Dec 2005 21:25:19 +0000 (13:25 -0800)]
[TG3]: ethtool -d hangs PCIe systems
Resubmitting after recommendation to use GET_REG32_1() instead of
GET_REG32_LOOP(..., 1). Retested. Problem remains fixed.
Prevent tg3_get_regs() from reading reserved and undocumented registers
at RX_CPU_BASE and TX_CPU_BASE offsets which caused hostile behavior
on PCIe platforms.
Acked-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH] Fix more radeon GART start calculation cases
As reported by Jules Villard <jvillard@ens-lyon.fr> and some others, the
recent GART aperture start reconfiguration causes problems on some
setups.
What I _think_ might be happening is that the X server is also trying to
muck around with the card memory map and is forcing it back into a wrong
setting that also happens to no longer match what the DRM wants to do
and blows up. There are bugs all over the place in that code (and still
some bugs in the DRM as well anyway).
This patch attempts to avoid that by using the largest of the 2 values,
which I think will cause it to behave as it used to for you and will
still fix the problem with machines that have an aperture size smaller
than the video memory.
David L Stevens [Tue, 27 Dec 2005 22:03:00 +0000 (14:03 -0800)]
[IPV6] mcast: Fix multiple issues in MLDv2 reports.
The below "jumbo" patch fixes the following problems in MLDv2.
1) Add necessary "ntohs" to recent "pskb_may_pull" check [breaks
all nonzero source queries on little-endian (!)]
2) Add locking to source filter list [resend of prior patch]
3) fix "mld_marksources()" to
a) send nothing when all queried sources are excluded
b) send full exclude report when source queried sources are
not excluded
c) don't schedule a timer when there's nothing to report
NOTE: RFC 3810 specifies the source list should be saved and each
source reported individually as an IS_IN. This is an obvious DOS
path, requiring the host to store and then multicast as many sources
as are queried (e.g., millions...). This alternative sends a full,
relevant report that's limited to number of sources present on the
machine.
4) fix "add_grec()" to send empty-source records when it should
The original check doesn't account for a non-empty source
list with all sources inactive; the new code keeps that
short-circuit case, and also generates the group header
with an empty list if needed.
5) fix mca_crcount decrement to be after add_grec(), which needs
its original value
These issues (other than item #1 ;-) ) were all found by Yan Zheng,
much thanks!
Signed-off-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David Kimdon [Tue, 27 Dec 2005 01:27:10 +0000 (17:27 -0800)]
[BR_NETFILTER]: Fix leak if skb traverses > 1 bridge
Call nf_bridge_put() before allocating a new nf_bridge structure and
potentially overwriting the pointer to a previously allocated one.
This fixes a memory leak which can occur when the bridge topology
allows for an skb to traverse more than one bridge.
Signed-off-by: David Kimdon <david.kimdon@devicescape.com> Signed-off-by: David S. Miller <davem@davemloft.net>
James Bottomley [Mon, 26 Dec 2005 15:58:49 +0000 (09:58 -0600)]
[PATCH] Fix Fibre Channel boot oops
The oops is characteristic of the underlying device being removed from
visibility before the class device, and sure enough we do device_del()
before transport_unregister() in the scsi_target_reap() routines. I've
no idea why this is suddenly showing up, since the code has been in
there since that function was first invented. However, I've confirmed
this fixes Andrew Vasquez's boot oops.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kurt Huwig [Sat, 24 Dec 2005 23:13:08 +0000 (00:13 +0100)]
[PATCH] n_r3964: fixed usage of HZ; removed bad include
Fix n_r3964 timeouts (hardcoded for 100Hz)
Also the include of <asm/termios.h> in 'n_r3964.h' is unnecessary and
prevents using the header file in any application that has to include
<termios.h> due to duplicate definition of 'struct termio'.
[PATCH] x86_64/ia64 : Fix compilation error for node_to_first_cpu
Fixes a compiler error in node_to_first_cpu, __ffs expects unsigned long as
a parameter; instead cpumask_t was being passed. The macro
node_to_first_cpu was not yet used in x86_64 and ia64 arches, and so we never
hit this. This patch replaces __ffs with first_cpu macro, similar to other
arches.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com> Signed-off-by: Ravikiran G Thirumalai <kiran@scalex86.org> Signed-off-by: Shai Fultheim <shai@scalex86.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Sat, 24 Dec 2005 03:54:46 +0000 (19:54 -0800)]
[PATCH] Fix memory ordering problem in wake_futex()
Fix a memory ordering problem that occurs on IA64. The "store" to q->lock_ptr
in wake_futex() can become visible before wake_up_all() clears the lock in the
futex_q.
Manfred Spraul [Sat, 24 Dec 2005 13:19:24 +0000 (14:19 +0100)]
[PATCH] forcedeth: fix random memory scribbling bug
Two critical bugs were found in forcedeth 0.47:
- TSO doesn't work.
- pci_map_single() for the rx buffers is called with size==0. This bug
is critical, it causes random memory corruptions on systems with an
iommu.
Below is a minimal fix for both bugs, for 2.6.15.
TSO will be fixed properly in the next version. Tested on x86-64.
Frank Pavlic [Tue, 13 Dec 2005 07:22:30 +0000 (08:22 +0100)]
[PATCH] s390: minor qeth network driver fixes
[patch 2/3] s390: minor qeth network driver fixes
From: Frank Pavlic <pavlic@de.ibm.com>
- use netif_carrier_on/off calls to tell network stack
link carrier state
- fix possible kfree on NULL
- PDU_LEN2 is at offset 0x29 otherwise OSN chpid won't initialize
Frank Pavlic [Tue, 13 Dec 2005 07:21:47 +0000 (08:21 +0100)]
[PATCH] s390: some minor qeth driver fixes
[patch 1/3] s390: some minor qeth driver fixes
From: Frank Pavlic <pavlic@de.ibm.com>
- let's have just one function for both ,input and output queue
to check qdio errors
- add /proc/s390dbf/qeth_qerr entries for outbound processing
- check removed for layer2 device in qeth_add_multicast_ipv6
- NULL pointer dereference with bonding and VLAN device fixed
- minimum length check for portname fixed
Tony Battersby [Wed, 21 Dec 2005 21:35:44 +0000 (16:35 -0500)]
[PATCH] fix libata inquiry VPD for ATAPI devices
The following patch prevents libata from incorrectly modifying inquiry
VPD pages and command support data from ATAPI devices. I have tested
the patch with a SATA ATAPI tape drive on an AHCI controller.
Patch is against kernel 2.4.32 with 2.4.32-libata1.patch applied.
David S. Miller [Fri, 23 Dec 2005 07:04:39 +0000 (23:04 -0800)]
[SPARC]: Kill CHILD_MAX.
It's definition is wrong (-1 means "no limit" not 999),
only the Sparc SunOS/Solaris compat code uses it, so
let's just kill it off completely from limits.h and
all referencing code.
Noticed by Ulrich Drepper.
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Renninger [Wed, 21 Dec 2005 06:29:00 +0000 (01:29 -0500)]
[ACPI] fix passive cooling regression
Return logic was inverted.
Going for changing the return value to not return zero as it is makes
more sense regarding the naming of the function (cpu_has_cpufreq()).
http://bugzilla.kernel.org/show_bug.cgi?id=3410
Signed-off-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Len Brown <len.brown@intel.com>
Russell King [Thu, 22 Dec 2005 23:21:38 +0000 (23:21 +0000)]
[MMC] Set correct capacity for 1024-byte block cards
We were passing set_capacity() the capacity we calculated in terms of
the number of blocks on the card, which happened to be the right units
for 512-byte block cards. However, with 1024-byte block cards, we
end up setting the capacity to half the number of blocks. Fix this
by shifting by the appropriate amount.
Thanks to Todd Blumer for pointing this out.
Use get_capacity() to report the card capacity, rather than
recalculating it from the CSD information.
Finally, use our chosen IO block size for the SET_BLOCKLEN command
rather than the CSD read block size. Currently these are equivalent,
but will not be in the future.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The problem is that the TIF_NEED_RESCHED flag is loaded _before_ the
preemption count is stored back, hence any interrupt coming within that
3 instruction window causing TIF_NEED_RESCHED to be set won't be
seen and scheduling won't happen as it should.
Nothing currently prevents gcc from performing that reordering. There
is already a barrier() before the decrement of the preemption count, but
another one is needed between this and the TIF_NEED_RESCHED flag test
for proper code ordering.
Signed-off-by: Nicolas Pitre <nico@cam.org> Acked-by: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David S. Miller [Thu, 22 Dec 2005 15:39:48 +0000 (07:39 -0800)]
[IPSEC]: Fix policy updates missed by sockets
The problem is that when new policies are inserted, sockets do not see
the update (but all new route lookups do).
This bug is related to the SA insertion stale route issue solved
recently, and this policy visibility problem can be fixed in a similar
way.
The fix is to flush out the bundles of all policies deeper than the
policy being inserted. Consider beginning state of "outgoing"
direction policy list:
policy A --> policy B --> policy C --> policy D
First, realize that inserting a policy into a list only potentially
changes IPSEC routes for that direction. Therefore we need not bother
considering the policies for other directions. We need only consider
the existing policies in the list we are doing the inserting.
Consider new policy "B'", inserted after B.
policy A --> policy B --> policy B' --> policy C --> policy D
Two rules:
1) If policy A or policy B matched before the insertion, they
appear before B' and thus would still match after inserting
B'
2) Policy C and D, now "shadowed" and after policy B', potentially
contain stale routes because policy B' might be selected
instead of them.
Therefore we only need flush routes assosciated with policies
appearing after a newly inserted policy, if any.
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Mackerras [Thu, 22 Dec 2005 10:55:37 +0000 (21:55 +1100)]
powerpc: Fix i8259 cascade on pSeries with XICS interrupt controller
It turns out that commit f9bd170a87948a9e077149b70fb192c563770fdf
broke the cascade from XICS to i8259 on pSeries machines; specifically
we ended up not ever doing the EOI on the XICS for the cascade. The
result was that interrupts from the serial ports (and presumably any
other devices using ISA interrupts) didn't get through. This fixes
it and also simplifies the code, by doing the EOI on the XICS in the
xics_get_irq routine after reading and acking the interrupt on the
i8259.
projects / linux-2.6 / log