Glauber Costa [Thu, 29 May 2008 03:34:19 +0000 (20:34 -0700)]
x86: change __setup_vector_irq with setup_vector_irq
We create a version of it for i386, and then take the CONFIG_X86_64
ifdef out of the game. We could create a __setup_vector_irq for i386,
but it would incur in an unnecessary lock taking. Moreover, it is better
practice to only export setup_vector_irq anyway.
Signed-off-by: Glauber Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Glauber Costa [Thu, 29 May 2008 03:05:46 +0000 (20:05 -0700)]
x86: remove ifdef from stepping
The stepping won't affect x86_64, since there are not x86_64 k7's
or pentiums. So, although it adds to the binary size, remove the ifdef
for smoother integration
Signed-off-by: Glauber Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Glauber Costa [Wed, 28 May 2008 15:57:02 +0000 (12:57 -0300)]
x86: use initial_code for i386
x86_64 jumps to whatever is written in "initial_code" symbol,
instead of a fixed address. Do it for i386 too. It will allow us
to integrate more of the smp boot code.
Signed-off-by: Glauber Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Glauber Costa [Wed, 28 May 2008 23:19:53 +0000 (16:19 -0700)]
x86: move x86_64 gdt closer to i386
i386 and x86_64 used two different schemes for maintaining the gdt.
With this patch, x86_64 initial gdt table is defined in a .c file,
same way as i386 is now. Also, we call it "gdt_page", and the descriptor,
"early_gdt_descr". This way we achieve common naming, which can allow for
more code integration.
Signed-off-by: Glauber Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Glauber Costa [Wed, 28 May 2008 01:22:54 +0000 (18:22 -0700)]
x86: use stack_start in x86_64
call x86_64's init_rsp stack_start, just as i386 does.
Put a zeroed stack segment for consistency. With this,
we can eliminate one ugly ifdef in smpboot.c.
Signed-off-by: Glauber Costa <gcosta@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
build: add __page_aligned_data and __page_aligned_bss
Making a variable page-aligned by using
__attribute__((section(".data.page_aligned"))) is fragile because if
sizeof(variable) is not also a multiple of page size, it leaves
variables in the remainder of the section unaligned.
This patch introduces two new qualifiers, __page_aligned_data and
__page_aligned_bss to set the section *and* the alignment of
variables. This makes page-aligned variables more robust because the
linker will make sure they're aligned properly. Unfortunately it
requires *all* page-aligned data to use these macros...
Cliff Wickman [Thu, 19 Jun 2008 16:16:24 +0000 (11:16 -0500)]
x86, SGI UV: TLB shootdown using broadcast assist unit, v6
v6: 6/19 close the security hole in uv_ptc_proc_write())
> Found a potential security hole while doing that:
> static ssize_t uv_ptc_proc_write(struct file *file, const char __user *user,
> size_t count, loff_t *data)
> if (copy_from_user(optstr, user, count))
> return -EFAULT;
>
> is count guaranteed to never be larger than 64?
Jack Steiner [Fri, 20 Jun 2008 02:51:05 +0000 (21:51 -0500)]
x86: fix stack overflow for large values of MAX_APICS
physid_mask_of_physid() causes a huge stack (12k) to be created if the
number of APICS is large. Replace physid_mask_of_physid() with a
new function that does not create large stacks. This is a problem only
on large x86_64 systems.
Ingo Molnar [Wed, 18 Jun 2008 12:51:57 +0000 (14:51 +0200)]
SGI UV: TLB shootdown using broadcast assist unit, fix
fix:
arch/x86/kernel/tlb_uv.c: In function ‘uv_table_bases_init':
arch/x86/kernel/tlb_uv.c:612: error: ‘bau_tabsp' undeclared (first use in this function)
arch/x86/kernel/tlb_uv.c:612: error: (Each undeclared identifier is reported only once
arch/x86/kernel/tlb_uv.c:612: error: for each function it appears in.)
Cliff Wickman [Thu, 12 Jun 2008 13:23:48 +0000 (08:23 -0500)]
SGI UV: TLB shootdown using broadcast assist unit, cleanups
TLB shootdown for SGI UV.
v1: 6/2 original
v2: 6/3 corrections/improvements per Ingo's review
v3: 6/4 split atomic operations off to a separate patch (Jeremy's review)
v4: 6/12 include <mach_apic.h> rather than <asm/mach-bigsmp/mach_apic.h>
(fixes a !SMP build problem that Ingo found)
fix the index on uv_table_bases[blade]
Cliff Wickman [Mon, 2 Jun 2008 13:56:14 +0000 (08:56 -0500)]
x86, SGI UV: TLB shootdown using broadcast assist unit
TLB shootdown for SGI UV.
Depends on patch (in tip/x86/irq):
x86-update-macros-used-by-uv-platform.patch Jack Steiner May 29
This patch provides the ability to flush TLB's in cpu's that are not on
the local node. The hardware mechanism for distributing the flush
messages is the UV's "broadcast assist unit".
The hook to intercept TLB shootdown requests is a 2-line change to
native_flush_tlb_others() (arch/x86/kernel/tlb_64.c).
This code has been tested on a hardware simulator. The real hardware
is not yet available.
The shootdown statistics are provided through /proc/sgi_uv/ptc_statistics.
The use of /sys was considered, but would have required the use of
many /sys files. The debugfs was also considered, but these statistics
should be available on an ongoing basis, not just for debugging.
Issues to be fixed later:
- The IRQ for the messaging interrupt is currently hardcoded as 200
(see UV_BAU_MESSAGE). It should be dynamically assigned in the future.
- The use of appropriate udelay()'s is untested, as they are a problem
in the simulator.
Bernhard Walle [Sun, 8 Jun 2008 13:46:31 +0000 (15:46 +0200)]
x86: use reserve_bootmem_generic() to reserve crashkernel memory on x86_64
This patch uses reserve_bootmem_generic() instead of reserve_bootmem()
to reserve the crashkernel memory on x86_64. That's necessary for NUMA
machines, see 00212fef814612245ed0261cbac8426d0c9a31a5:
[PATCH] Fix kdump Crash Kernel boot memory reservation for NUMA machines
This patch will fix a boot memory reservation bug that trashes memory on
the ES7000 when loading the kdump crash kernel.
The code in arch/x86_64/kernel/setup.c to reserve boot memory for the crash
kernel uses the non-numa aware "reserve_bootmem" function instead of the
NUMA aware "reserve_bootmem_generic". I checked to make sure that no other
function was using "reserve_bootmem" and found none, except the ones that
had NUMA ifdef'ed out.
I have tested this patch only on an ES7000 with NUMA on and off (numa=off)
in a single (non-NUMA) and multi-cell (NUMA) configurations.
Signed-off-by: Amul Shah <amul.shah@unisys.com> Looks-good-to: Vivek Goyal <vgoyal@in.ibm.com> Cc: Andi Kleen <ak@muc.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The switch-back to reserve_bootmem() was accidentally introduced in 5c3391f9f749023a49c64d607da4fb49263690eb when adding the BOOTMEM_EXCLUSIVE
parameter.
Signed-off-by: Bernhard Walle <bwalle@suse.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Bernhard Walle [Sun, 8 Jun 2008 13:46:30 +0000 (15:46 +0200)]
x86: add flags parameter to reserve_bootmem_generic()
This patch adds a 'flags' parameter to reserve_bootmem_generic() like it
already has been added in reserve_bootmem() with commit 72a7fe3967dbf86cb34e24fbf1d957fe24d2f246.
It also changes all users to use BOOTMEM_DEFAULT, which doesn't effectively
change the behaviour. Since the change is x86-specific, I don't think it's
necessary to add a new API for migration. There are only 4 users of that
function.
The change is necessary for the next patch, using reserve_bootmem_generic()
for crashkernel reservation.
Signed-off-by: Bernhard Walle <bwalle@suse.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Randy Dunlap [Thu, 5 Jun 2008 18:10:59 +0000 (11:10 -0700)]
x86: fix setup.c printk format warning
Fix setup.c printk format warning:
linux-next-20080605/arch/x86/kernel/setup.c: In function 'setup_per_cpu_areas':
linux-next-20080605/arch/x86/kernel/setup.c:173: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'ssize_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mike Travis [Mon, 12 May 2008 19:21:12 +0000 (21:21 +0200)]
sched, numa: replace MAX_NUMNODES with nr_node_ids in kernel/sched.c
* Replace usages of MAX_NUMNODES with nr_node_ids in kernel/sched.c,
where appropriate. This saves some allocated space as well as many
wasted cycles going through node entries that are non-existent.
Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/built-in.o(.cpuinit.text+0x3c6e): In function `get_local_pda':
: undefined reference to `_cpu_pda'
arch/x86/kernel/built-in.o(.cpuinit.text+0x3cd1): In function `get_local_pda':
: undefined reference to `after_bootmem'
arch/x86/kernel/built-in.o(.cpuinit.text+0x3cec): In function `get_local_pda':
: undefined reference to `_cpu_pda'
make[2]: *** [.tmp_vmlinux1] Error 1
Mike Travis [Mon, 12 May 2008 19:21:13 +0000 (21:21 +0200)]
x86: remove static boot_cpu_pda array v2
* Remove the boot_cpu_pda array and pointer table from the data section.
Allocate the pointer table and array during init. do_boot_cpu()
will reallocate the pda in node local memory and if the cpu is being
brought up before the bootmem array is released (after_bootmem = 0),
then it will free the initial pda. This will happen for all cpus
present at system startup.
This removes 512k + 32k bytes from the data section.
For inclusion into sched-devel/latest tree.
Based on:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
+ sched-devel/latest .../mingo/linux-2.6-sched-devel.git
Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mike Travis [Mon, 12 May 2008 19:21:12 +0000 (21:21 +0200)]
x86: remove the static 256k node_to_cpumask_map
* Consolidate node_to_cpumask operations and remove the 256k
byte node_to_cpumask_map. This is done by allocating the
node_to_cpumask_map array after the number of possible nodes
(nr_node_ids) is known.
* Debug printouts when CONFIG_DEBUG_PER_CPU_MAPS is active have
been increased. It now shows faults when calling node_to_cpumask()
and node_to_cpumask_ptr().
For inclusion into sched-devel/latest tree.
Based on:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
+ sched-devel/latest .../mingo/linux-2.6-sched-devel.git
Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mike Travis [Mon, 12 May 2008 19:21:12 +0000 (21:21 +0200)]
x86: restore pda nodenumber field
* Restore the nodenumber field in the x86_64 pda. This field is slightly
different than the x86_cpu_to_node_map mainly because it's a static
indication of which node the cpu is on while the cpu to node map is a
dyanamic mapping that may get reset if the cpu goes offline. This also
simplifies the numa_node_id() macro.
For inclusion into sched-devel/latest tree.
Based on:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
+ sched-devel/latest .../mingo/linux-2.6-sched-devel.git
Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mike Travis [Mon, 12 May 2008 19:21:12 +0000 (21:21 +0200)]
x86: cleanup early per cpu variables/accesses v4
* Introduce a new PER_CPU macro called "EARLY_PER_CPU". This is
used by some per_cpu variables that are initialized and accessed
before there are per_cpu areas allocated.
["Early" in respect to per_cpu variables is "earlier than the per_cpu
areas have been setup".]
The DEFINE macro defines the per_cpu variable as well as the early
map and pointer. It also initializes the per_cpu variable and map
elements to "_initvalue". The early_* macros provide access to
the initial map (usually setup during system init) and the early
pointer. This pointer is initialized to point to the early map
but is then NULL'ed when the actual per_cpu areas are setup. After
that the per_cpu variable is the correct access to the variable.
The early_per_cpu() macro is not very efficient but does show how to
access the variable if you have a function that can be called both
"early" and "late". It tests the early ptr to be NULL, and if not
then it's still valid. Otherwise, the per_cpu variable is used
instead:
* Add a flag "arch_provides_topology_pointers" that indicates pointers
to topology cpumask_t maps are available. Otherwise, use the function
returning the cpumask_t value. This is useful if cpumask_t set size
is very large to avoid copying data on to/off of the stack.
* The coverage of CONFIG_DEBUG_PER_CPU_MAPS has been increased while
the non-debug case has been optimized a bit.
* Remove an unreferenced compiler warning in drivers/base/topology.c
* Clean up #ifdef in setup.c
For inclusion into sched-devel/latest tree.
Based on:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
+ sched-devel/latest .../mingo/linux-2.6-sched-devel.git
Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mike Travis [Mon, 12 May 2008 19:21:12 +0000 (21:21 +0200)]
x86: modify Kconfig to allow up to 4096 cpus
* Increase the limit of NR_CPUS to 4096 and introduce a boolean
called "MAXSMP" which when set (e.g. "allyesconfig"), will set
NR_CPUS = 4096 and NODES_SHIFT = 9 (512).
* Changed max setting for NODES_SHIFT from 15 to 9 to accurately
reflect the real limit.
Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mike Travis [Mon, 12 May 2008 19:21:12 +0000 (21:21 +0200)]
x86: fix remove cpu_pda table patch
Mike Travis wrote:
> Ingo Molnar wrote:
>> * Mike Travis <travis@sgi.com> wrote:
>>
>>> [Ingo - please replace "PATCH 07/11" with this one.]
>>>
>>> * Remove 544k bytes from the kernel by removing the boot_cpu_pda
>>> array from the data section and allocating it during startup.
>>>
>>> Fixed panic in setup_per_cpu_areas when HOTPLUG_CPU not set.
>>>
>>> For inclusion into sched-devel/latest tree.
>> sched-devel.git randconfig testing found another crash with your queue:
>>
>> [ 0.111060] Brought up 1 CPUs
>> [ 0.111986] Total of 1 processors activated (4022.73 BogoMIPS).
>> [ 0.112987] Testing NMI watchdog ... <1>BUG: unable to handle kernel NULL pointer dereference at 0000000000000040
>> [ 0.114982] IP: [<ffffffff8180d4a0>] check_nmi_watchdog+0xb0/0x210
>> [ 0.114982] PGD 0
>> [ 0.114982] Oops: 0000 [1] SMP
>> [ 0.114982] CPU 0
>> [............]
>>
>> http://redhat.com/~mingo/misc/config-Mon_Apr_28_23_25_25_CEST_2008.bad
>> http://redhat.com/~mingo/misc/log-Mon_Apr_28_23_25_25_CEST_2008.bad
>>
>> Ingo
>
> Hi Ingo,
>
> I need a bit more information on your hardware configuration. Building a
> kernel with the above config file started up fine on both the Intel and AMD
> boxes.
>
> Based on the above output it looks like it might be a UP machine?
...
Ok, I think I found it. In check_nmi_watchdog():
for (cpu = 0; cpu < NR_CPUS; cpu++)
prev_nmi_count[cpu] = cpu_pda(cpu)->__nmi_count;
As I mentioned it works fine on both of my systems so could you try it out?
Thanks!
Mike
--
* Change function check_nmi_watchdog() to use nr_cpu_ids instead of NR_CPUS.
Based on:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
+ sched-devel/latest .../mingo/linux-2.6-sched-devel.git
Signed-off-by: Mike Travis <travis@sgi.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Matthew Garrett [Tue, 1 Jul 2008 00:12:06 +0000 (01:12 +0100)]
x86, ioapic, acpi quirk: disable IRQ 0 through I/O APIC for some HP systems
Some HP laptops have a problem with their DSDT reporting as
HP/SB400/10000, which includes some code which overrides all temperature
trip points to 16C if the INTIN2 input of the I/O APIC is enabled. This
input is incorrectly designated the ISA IRQ 0 via an interrupt source
override even though it is wired to the output of the master 8259A and
INTIN0 is not connected at all. So far two models have been identified,
namely nx6125 and nx6325.
Use a knob provided by the I/O APIC interrupt registration code to
abandon any attempts to route IRQ 0 through the I/O APIC for these
systems.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Len Brown <lenb@kernel.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86, ioapic, acpi: add a knob to disable IRQ 0 through I/O APIC
As discovered recently some systems exhibit problems when the 8254 timer
IRQ is routed through the I/O APIC. These problems do not affect the
timer IRQ itself and therefore cannot be detected when the correctness of
operation of the interrupt is verified in check_timer(). Therefore the
I/O APIC path of the timer IRQ has to be disabled entirely.
This is a change that lets platforms ask for the timer IRQ not to be
registered in the I/O APIC interrupt tables. The local APIC and ExtINTA
paths are unaffected. This request is only taken into account for ACPI
platforms as MP table systems seem unaffected so far.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Len Brown <lenb@kernel.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu [Fri, 20 Jun 2008 14:33:31 +0000 (07:33 -0700)]
x86: simplify x86_mpparse dependency check
"Maciej W. Rozycki" <macro@linux-mips.org> said:
> Given X86_64 selects X86_LOCAL_APIC I am not sure the redundancy seen
>above does not actually obscure the logic behind... I think:
>
> depends on X86_LOCAL_APIC && !X86_VISWS
>
>would be clearer and get the same.
Suggested-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu [Thu, 19 Jun 2008 19:13:09 +0000 (12:13 -0700)]
x86: let MPS support be selectable, v2
v2: seperate "fix for compiling when MPPARSE is not set" to another patch
make X86_MPPARSE to be selectable only when acpi is set and
X86_MPPARSE will be set if acpi is not set.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu [Thu, 19 Jun 2008 00:29:31 +0000 (17:29 -0700)]
x86: update mptable fix with no ioapic v2
if the system doesn't have ioapic, we don't need to store entries for mptable
update
also let mp_config_acpi_gsi not call func in mpparse
so later could decouple mpparse with acpi more easily
Reported-by: Daniel Exner <dex@dragonslave.de> Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Daniel Exner <dex@dragonslave.de> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Huang, Ying [Wed, 11 Jun 2008 03:33:39 +0000 (11:33 +0800)]
x86 boot: pass E820 memory map entries more than 128 via linked list of setup data
Because of the size limits of struct boot_params (zero page), the
maximum number of E820 memory map entries can be passed to kernel is
128. As pointed by Paul Jackson, there is some machine produced by SGI
with so many nodes that the number of E820 memory map entries is more
than 128. To enabling Linux kernel on these system, a new setup data
type named SETUP_E820_EXT is defined to pass additional memory map
entries to Linux kernel.
This patch is based on x86/auto-latest branch of git-x86 tree and has
been tested on x86_64 and i386 platform.
Bernhard Walle [Sun, 8 Jun 2008 13:46:31 +0000 (15:46 +0200)]
x86: use reserve_bootmem_generic() to reserve crashkernel memory on x86_64
This patch uses reserve_bootmem_generic() instead of reserve_bootmem()
to reserve the crashkernel memory on x86_64. That's necessary for NUMA
machines, see 00212fef814612245ed0261cbac8426d0c9a31a5:
[PATCH] Fix kdump Crash Kernel boot memory reservation for NUMA machines
This patch will fix a boot memory reservation bug that trashes memory on
the ES7000 when loading the kdump crash kernel.
The code in arch/x86_64/kernel/setup.c to reserve boot memory for the crash
kernel uses the non-numa aware "reserve_bootmem" function instead of the
NUMA aware "reserve_bootmem_generic". I checked to make sure that no other
function was using "reserve_bootmem" and found none, except the ones that
had NUMA ifdef'ed out.
I have tested this patch only on an ES7000 with NUMA on and off (numa=off)
in a single (non-NUMA) and multi-cell (NUMA) configurations.
Signed-off-by: Amul Shah <amul.shah@unisys.com> Looks-good-to: Vivek Goyal <vgoyal@in.ibm.com> Cc: Andi Kleen <ak@muc.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The switch-back to reserve_bootmem() was accidentally introduced in 5c3391f9f749023a49c64d607da4fb49263690eb when adding the BOOTMEM_EXCLUSIVE
parameter.
Signed-off-by: Bernhard Walle <bwalle@suse.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Bernhard Walle [Sun, 8 Jun 2008 13:46:30 +0000 (15:46 +0200)]
x86: add flags parameter to reserve_bootmem_generic()
This patch adds a 'flags' parameter to reserve_bootmem_generic() like it
already has been added in reserve_bootmem() with commit 72a7fe3967dbf86cb34e24fbf1d957fe24d2f246.
It also changes all users to use BOOTMEM_DEFAULT, which doesn't effectively
change the behaviour. Since the change is x86-specific, I don't think it's
necessary to add a new API for migration. There are only 4 users of that
function.
The change is necessary for the next patch, using reserve_bootmem_generic()
for crashkernel reservation.
Signed-off-by: Bernhard Walle <bwalle@suse.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
> That helped a lot, the system seems to work normally now.
>
> Here's the relevant snippet from dmesg:
>
> [ 0.108006] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> [ 0.108006] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
> [ 0.108006] ...trying to set up timer (IRQ0) through the 8259A ... <3>
> [ 0.108006] ..... (found apic 0 pin 2) ...<3> failed.
> [ 0.108006] ...trying to set up timer as Virtual Wire IRQ...<3> works.
>
> and the whole thing is at: http://www.sisk.pl/kernel/debug/20080618/dmesg-2.log
Hmm, that only proved the 8259A is indeed wired to the pin #2 of the I/O
APIC.
> I, personally, don't have any and AMD only has SB600 documentation on its
> web page (it's still marked as "AMD confidential" ;-)).
Well, the IC block is most likely the same as that's not rocket science
and once done there is no need to fiddle with that. That written, I am
afraid there is nothing useful about the IC in the document, except that
it's there and consists of an I/O APIC providing 24 inputs and the usual
pair of 8259A cores. Thanks for the reference anyway.
> There is an interrupt controller in there, but I'm not sure if there's any
> 8259A. The northbridge is on the CPU, actually.
I will praise the day someone ships an x86 machine without an 8259A core!
As expressed in another mail I suspect there may actually be a direct
route from the 8254 to INTIN0 in the southbridge -- this is what other
bootstrap logs seen in the Internet suggest. This would mean this
particular BIOS is buggy (is it the latest version?) and provides an
incorrect IRQ override in its ACPI tables, for example because the
responsible block has been blindly copied from a machine using a commoner
wiring. This could be moderately easily fixed up with a quirk based on
the PCI ID (after checking it again, we actually used to have a quirk for
ATI in this area, but the way it was done suggests the issue was not
understood well enough).
Could you please remove the hack sent yesterday and test the patch
provided below? I do hope it builds, but I have no immediate means to
check it. Please report the output. The intent is to test INTIN0
directly before testing INTIN2 through the 8259A. Thanks.
Aside of that, what I have gathered from your reports (please correct me
if I have got it wrong) is that when the through-8259A mode is used, then
after a while 8254 timer interrupts stop arriving. What's interesting,
the "Virtual Wire IRQ" seems to work for you correctly (that's quite an
odd setup where a local APIC input is used in the native mode -- please
post /proc/interrupts for confirmation), which in turn implies the master
8259A drives its INT output as we expect. Why would the I/O APIC input
have problems then? Hmm...
[ mingo@elte.hu: revert the "x86: fix IO APIC breakage on HP nx6325"
version. ]
> > With such a configuration the "x86: I/O APIC: timer through 8259A
> > second-chance" patch should not matter, because the only change it
> > introduces is an attempt to try the same I/O APIC pin again, but with the
> > IRQ0 line of the master 8259A enabled. That's not a terribly unusual
> > configuration and nothing should get confused in the system.
>
> But it _does_ get confused, really.
Something certainly gets confused, but so far I am not sure which bit
exactly it is, are you?
> > Barring the unlikely possibility of the 8259A actually being wired to
> > INTIN2 of the I/O APIC I can see two possible explanations:
> >
> > 1. The 8259A interrupt actually escapes to the CPU somehow and is handled
> > as an ExtINTA interrupt. This would make the code in check_timer()
> > decide it has found a working configuration, while actually it has been
> > fooled.
[...]
> Here you go:
>
> [ 0.108006] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
> [ 0.108006] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
> [ 0.108006] ...trying to set up timer (IRQ0) through the 8259A ... <3>
> [ 0.108006] ..... (found apic 0 pin 2) ...<3> works.
>
> The full dmesg is at: http://www.sisk.pl/kernel/debug/20080618/dmesg-1.log
Thanks. In this case I suspect the case #1 quoted above happens, that is
the 8259A manages to deliver its interrupt somehow. Note at this stage it
is meant to be in the AEOI mode, so it can happily resubmit the interrupt
indefinitely with no additional handling as long as it receives INTA
cycles.
Can you please try the patch below on top of "x86: I/O APIC: timer
through 8259A second-chance" to see whether my hypothesis is true? It
modifies the through-8259A setup path so that the APIC input gets masked,
but the 8259A has the timer interrupt still enabled. Let me know how the
timer interrupt is routed in this case.
Bisected-by: "Rafael J. Wysocki" <rjw@sisk.pl> Tested-by: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86: APIC/SMP: Downgrade the NMI watchdog for "noapic"
If configured to use the I/O APIC, the NMI watchdog is deemed to fail if
the chip has been deactivated as a result of "noapic". Downgrade to the
local APIC watchdog similarly to what is done for the UP case.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86: APIC/SMP: Downgrade the NMI watchdog for "nosmp"
If configured to use the I/O APIC, the NMI watchdog is deemed to fail if
the chip has been deactivated as a result of "nosmp". Downgrade to the
local APIC watchdog similarly to what is done for the UP case.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
For the UP case the NMI watchdog downgrade is done consistently in
APIC_init_uniprocessor() now. Remove redundant code used only when
BIOS-disabled local APIC is activated.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86: APIC/UP: Downgrade the NMI watchdog for no I/O APIC
If configured to use the I/O APIC, the NMI watchdog is deemed to fail if
the chip will not be used in the UP configuration, because "noapic" has
been specified or the chip is simply not there. Downgrade to the local
APIC watchdog to rectify.
The new #ifdef is ugly, I know. A proper solution is to provide suitable
definitions of smp_found_config, etc. for !CONFIG_X86_IO_APIC in a header.
Likewise the whole if () condition should be moved to a static inline
function. Such clean-ups are beyond the scope of this change and can be
done once the whole issue of the timer has been sorted out.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
A downgrade helper for the NMI watchdog to be used in all places where
the I/O APIC watchdog may have been requested, but the I/O APIC is found
not to be there or meant to be left disabled. This is so that the
reconfiguration is cosistent and defined in a single place only.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cyrill Gorcunov [Thu, 29 May 2008 18:32:30 +0000 (22:32 +0400)]
x86: IO-APIC - use NMI_NONE instead of numeric constant
Not sure but maybe it is better to use NMI_DISABLED,
will take a look. But for now this patch is not change
anything in logic so it will not hurt/broke the kernel.
For most cases nmi_watchdog assignment is by one of NMI_*
macro so I think there it make sense too.
Ingo Molnar [Sat, 31 May 2008 10:20:10 +0000 (12:20 +0200)]
x86 build fix:
arch/x86/kernel/io_apic_64.c: In function 'check_timer':
arch/x86/kernel/io_apic_64.c:1688: error: 'vector' undeclared (first use in this function)
arch/x86/kernel/io_apic_64.c:1688: error: (Each undeclared identifier is reported only once
arch/x86/kernel/io_apic_64.c:1688: error: for each function it appears in.)
Some systems incorrectly report the ExtINTA pin of the I/O APIC as the
genuine target of the timer interrupt. Here is a change that copies timer
pin information found to the other pin if one has been found only. This
way both a direct and a through-8259A route is tested with the pin letting
these problematic systems work well enough. If no timer pin information
has been found for the I/O APIC, then local APIC variations are tried
only, similarly to what is done without the change (except without the
misleading messages).
Obviously if we try the first-chance path without being told by the BIOS
to do so, we should not complain either, so do not print the message in
this case.
The 64-bit variation should be updated with a call to
replace_pin_at_irq() which can be done with the upcoming merge. Since
add_pin_to_irq() is now always called in the first-chance path, the
condition to require it in the second-chance path no longer happens.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86: I/O APIC: unmask the second-chance timer interrupt
Unmask the timer interrupt line set up in the through-8259A mode
explicitly after setup_timer_IRQ0_pin() has set up the I/O APIC interrupt
redirection entry to let the two operations be unbound from each other.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
projects / linux-2.6 / log