Daniel Drake [Mon, 8 May 2006 22:43:02 +0000 (23:43 +0100)]
[PATCH] USB shuttle_usbat: hardcode flash detection for now
After some further testing with my flash device I realised that our current
probe doesn't always work (e.g. when no media is inserted).
Now that Peter Chubb's patch has simplified the detection of 99% of the HP CD
writers out there, we have a much smaller range of hardware to work with on
the shared device ID, so it should be possible to try some of the previous
probe options again: we just need to find another tester with a USBAT2-based HP
CD writer.
This patch hardcodes the flash detection until someone comes along with one of
these obscure CD drives. Note that these devices are extremely rare, so even if
we can't ever find a decent probe method, at least we will be supporting almost
all of the USBAT-based hardware out there.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Chubb [Tue, 2 May 2006 17:29:34 +0000 (18:29 +0100)]
[PATCH] USB: shuttle_usbat: Hardcode detection of HP CDRW devices
Use USB vendor and product IDs to determine whether the attached
device is a CDROM or a Flash device. Daniel Drake says that the
*same* vendor and product IDs for non-HP vendor ID could be either
flash or cdrom, so try to probe for them.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au> Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Chubb [Tue, 2 May 2006 17:30:12 +0000 (18:30 +0100)]
[PATCH] USB: shuttle_usbat: Fix handling of scatter-gather buffers
I've worked out what's going wrong. The scsi layer is now much
more likely to pass down scatterlists instead of plain buffers. So
you have to make sure that they're handled correctly. In one of the
changes along the way, usbat_write_block and friends stopped obeying
the srb->use_sg flag.
Anyway, with the appended patch, and the one I'm putting in the next email, it
all seems to work for the HP cd4e. Of course, someone's going to have
to test it with the flash drives as well....
This patch teaches the usbat_{read,write}_block functions to
obey the use_sg flag in the scsi-request.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au> Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 27 Apr 2006 19:54:22 +0000 (15:54 -0400)]
[PATCH] USB: usbcore: always turn on hub port power
Some hubs claim not to support port-power switching, and right now the
hub driver believes them and does not enable power to their ports.
However it turns out that even though they don't actually switch power,
they do ignore all events on a port until told to turn on the power!
This problem has been reported by several users.
This revised patch (as672b) makes the hub driver always try to turn on
port power to all hubs, regardless of what the hub descriptor says. It
also adds a comment explaining the need for this.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kumar Gala [Tue, 11 Apr 2006 15:07:16 +0000 (10:07 -0500)]
[PATCH] USB: allow multiple types of EHCI controllers to be built as modules
In some systems we may have both a platform EHCI controller and PCI EHCI
controller. Previously we couldn't build the EHCI support as a module due
to conflicting module_init() calls in the code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adrian Bunk [Sat, 15 Apr 2006 09:17:27 +0000 (11:17 +0200)]
[PATCH] USB: sisusbvga: possible cleanups
This patch contains the following possible cleanups:
- make needlessly global functions static
- function and struct declarations belong into header files
- make SiS_VCLKData const
- #if 0 the following unused global functions:
- sisusb.c: sisusb_writew()
- sisusb.c: sisusb_readw()
- sisusb_init.c: SiSUSB_GetModeID()
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Arjan van de Ven [Tue, 28 Mar 2006 09:00:21 +0000 (01:00 -0800)]
[PATCH] USB: convert the semaphores in the sisusb driver to mutexes
From: Arjan van de Ven <arjan@infradead.org>
Convert the semaphores-used-as-mutex to mutexes in the sisusb video driver;
this required manual checking due to the "return as locked" stuff in this
driver, but the ->lock semaphore is still used as mutex in the end.
Signed-off-by: Arjan van de Ven <arjan@infradead.org> Cc: Thomas Winischhofer <winischhofer.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eduard Warkentin [Thu, 18 May 2006 08:13:17 +0000 (01:13 -0700)]
[PATCH] USB: added support for ASIX 88178 chipset USB Gigabit Ethernet adaptor
Add support for detection and dworking with a ASIX 88178 based USB-Gigabit
adaptor. With the patch, it is detected and handled correctly by the asix
module.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sat, 13 May 2006 02:24:34 +0000 (19:24 -0700)]
[PATCH] USB: usbnet, zaurus mtu fixup
This includes an MTU fixup which could affect larger packets with newer
Zaurii, described as http://bugzilla.kernel.org/show_bug.cgi?id=6286;
plus minor whitespace cleanup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Sat, 13 May 2006 20:50:47 +0000 (22:50 +0200)]
[PATCH] USB: cdc-acm: add a new special case for modems with buggy firmware
this fixes the "duplicated text" bug. There's a modem that cannot cope
with large transfers and more than one urb in flight. This patch adds a
special case to the driver.
Signed-off-by: Oliver Neukum <oliver@neukum.name> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Henk Vergonet [Mon, 15 May 2006 10:34:43 +0000 (12:34 +0200)]
[PATCH] USB: add YEALINK phones to the HID_QUIRK_IGNORE blacklist
Keys on Yealink based phones will not function properly when using the
generic HID driver. This patch prevents the generic HID code from
grabbing the device before the regular yealink driver can get a grip on
it.
Paul Serice [Wed, 7 Jun 2006 17:23:38 +0000 (10:23 -0700)]
[PATCH] USB: EHCI works again on NVidia controllers with >2GB RAM
From: Paul Serice <paul@serice.net>
The workaround in commit f7201c3dcd7799f2aa3d6ec427b194225360ecee
broke. The work around requires memory for DMA transfers for some
NVidia EHCI controllers to be below 2GB, but recent changes have
caused some DMA memory to be allocated before the DMA mask is set.
Signed-off-by: Paul Serice <paul@serice.net> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rene Herman [Tue, 6 Jun 2006 21:54:02 +0000 (23:54 +0200)]
[PATCH] Driver model: add ISA bus
During the recent "isa drivers using platform devices" discussion it was
pointed out that (ALSA) ISA drivers ran into the problem of not having
the option to fail driver load (device registration rather) upon not
finding their hardware due to a probe() error not being passed up
through the driver model. In the course of that, I suggested a seperate
ISA bus might be best; Russell King agreed and suggested this bus could
use the .match() method for the actual device discovery.
The attached does this. For this old non (generically) discoverable ISA
hardware only the driver itself can do discovery so as a difference with
the platform_bus, this isa_bus also distributes match() up to the driver.
As another difference: these devices only exist in the driver model due
to the driver creating them because it might want to drive them, meaning
that all device creation has been made internal as well.
The usage model this provides is nice, and has been acked from the ALSA
side by Takashi Iwai and Jaroslav Kysela. The ALSA driver module_init's
now (for oldisa-only drivers) become:
static int __init alsa_card_foo_init(void)
{
return isa_register_driver(&snd_foo_isa_driver, SNDRV_CARDS);
}
Quite like the other bus models therefore. This removes a lot of
duplicated init code from the ALSA ISA drivers.
The passed in isa_driver struct is the regular driver struct embedding a
struct device_driver, the normal probe/remove/shutdown/suspend/resume
callbacks, and as indicated that .match callback.
The "SNDRV_CARDS" you see being passed in is a "unsigned int ndev"
parameter, indicating how many devices to create and call our methods with.
The platform_driver callbacks are called with a platform_device param;
the isa_driver callbacks are being called with a "struct device *dev,
unsigned int id" pair directly -- with the device creation completely
internal to the bus it's much cleaner to not leak isa_dev's by passing
them in at all. The id is the only thing we ever want other then the
struct device * anyways, and it makes for nicer code in the callbacks as
well.
With this additional .match() callback ISA drivers have all options. If
ALSA would want to keep the old non-load behaviour, it could stick all
of the old .probe in .match, which would only keep them registered after
everything was found to be present and accounted for. If it wanted the
behaviour of always loading as it inadvertently did for a bit after the
changeover to platform devices, it could just not provide a .match() and
do everything in .probe() as before.
If it, as Takashi Iwai already suggested earlier as a way of following
the model from saner buses more closely, wants to load when a later bind
could conceivably succeed, it could use .match() for the prerequisites
(such as checking the user wants the card enabled and that port/irq/dma
values have been passed in) and .probe() for everything else. This is
the nicest model.
To the code...
This exports only two functions; isa_{,un}register_driver().
isa_register_driver() register's the struct device_driver, and then
loops over the passed in ndev creating devices and registering them.
This causes the bus match method to be called for them, which is:
if (dev->platform_data == isa_driver) {
if (!isa_driver->match ||
isa_driver->match(dev, to_isa_dev(dev)->id))
return 1;
dev->platform_data = NULL;
}
return 0;
}
The first thing this does is check if this device is in fact one of this
driver's devices by seeing if the device's platform_data pointer is set
to this driver. Platform devices compare strings, but we don't need to
do that with everything being internal, so isa_register_driver() abuses
dev->platform_data as a isa_driver pointer which we can then check here.
I believe platform_data is available for this, but if rather not, moving
the isa_driver pointer to the private struct isa_dev is ofcourse fine as
well.
Then, if the the driver did not provide a .match, it matches. If it did,
the driver match() method is called to determine a match.
If it did _not_ match, dev->platform_data is reset to indicate this to
isa_register_driver which can then unregister the device again.
If during all this, there's any error, or no devices matched at all
everything is backed out again and the error, or -ENODEV, is returned.
isa_unregister_driver() just unregisters the matched devices and the
driver itself.
More global points/questions...
- I'm introducing include/linux/isa.h. It was available but is ofcourse
a somewhat generic name. Moving more isa stuff over to it in time is
ofcourse fine, so can I have it please? :)
- I'm using device_initcall() and added the isa.o (dependent on
CONFIG_ISA) after the base driver model things in the Makefile. Will
this do, or I really need to stick it in drivers/base/init.c, inside
#ifdef CONFIG_ISA? It's working fine.
Lastly -- I also looked, a bit, into integrating with PnP. "Old ISA"
could be another pnp_protocol, but this does not seem to be a good
match, largely due to the same reason platform_devices weren't -- the
devices do not have a life of their own outside the driver, meaning the
pnp_protocol {get,set}_resources callbacks would need to callback into
driver -- which again means you first need to _have_ that driver. Even
if there's clean way around that, you only end up inventing fake but
valid-form PnP IDs and generally catering to the PnP layer without any
practical advantages over this very simple isa_bus. The thing I also
suggested earlier about the user echoing values into /sys to set up the
hardware from userspace first is... well, cute, but a horrible idea from
a user standpoint.
Comments ofcourse appreciated. Hope it's okay. As said, the usage model
is nice at least.
Signed-off-by: Rene Herman <rene.herman@keyaccess.nl>
Alan Stern [Fri, 16 Jun 2006 21:10:48 +0000 (17:10 -0400)]
[PATCH] Driver Core: Make dev_info and friends print the bus name if there is no driver
This patch (as721) makes dev_info and related macros print the device's
bus name if the device doesn't have a driver, instead of printing just a
blank. If the device isn't on a bus either... well, then it does leave
a blank space. But it will be easier for someone else to change if they
want.
Cc: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] Driver core: add proper symlinks for devices
We need to create the "compatible" symlinks that class_devices used to
create when they were in the class directories so that userspace does
not know anything changed at all.
Yeah, we have a lot of symlinks now, but we should be able to get rid of
them in a year or two... (wishful thinking...)
Kay Sievers [Thu, 15 Jun 2006 13:31:56 +0000 (15:31 +0200)]
[PATCH] Driver core: add generic "subsystem" link to all devices
Like the SUBSYTEM= key we find in the environment of the uevent, this
creates a generic "subsystem" link in sysfs for every device. Userspace
usually doesn't care at all if its a "class" or a "bus" device. This
provides an unified way to determine the subsytem of a device, regardless
of the way the driver core has created it.
Signed-off-by: Kay Sievers <kay.sievers@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] Driver core: allow struct device to have a dev_t
This is the first step in moving class_device to being replaced by
struct device. It allows struct device to export a dev_t and makes it
easy to dynamically create and destroy struct device as long as they are
associated with a specific class.
Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Holzheu [Tue, 9 May 2006 10:53:49 +0000 (12:53 +0200)]
[PATCH] Driver Core: Add /sys/hypervisor when needed
To have a home for all hypervisors, this patch creates /sys/hypervisor.
A new config option SYS_HYPERVISOR is introduced, which should to be set
by architecture dependent hypervisors (e.g. s390 or Xen).
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Michael Holzheu <holzheu@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Russell King [Sat, 6 May 2006 07:15:26 +0000 (08:15 +0100)]
[PATCH] Driver Core: Fix platform_device_add to use device_add
platform_device_add() should be using device_add() rather
than device_register() - any platform device passed to
platform_device_add() should have already been initialised,
either by platform_device_alloc() or platform_device_register().
Signed-off-by: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
class_device_add needs to check the return value of all the setup it
does. It doesn't handle out of memory well. This is not complete, probably
more needs to be done.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Hansjoerg Lipp [Sat, 22 Apr 2006 16:43:00 +0000 (18:43 +0200)]
[PATCH] i4l gigaset: move sysfs entry to tty class device
Using the class device pointer returned by tty_register_device() with
part 1 of the patch, attach the Gigaset drivers' "cidmode" sysfs entry
to its tty class device, where it can be found more easily by users
who do not know nor care which USB port the device is attached to.
Hansjoerg Lipp [Sat, 22 Apr 2006 16:36:53 +0000 (18:36 +0200)]
[PATCH] TTY: return class device pointer from tty_register_device()
Let tty_register_device() return a pointer to the class device it creates.
This allows registrants to add their own sysfs files under the class
device node.
Brice Goglin [Wed, 21 Jun 2006 03:03:02 +0000 (20:03 -0700)]
[PATCH] add __iowrite64_copy
Introduce __iowrite64_copy. It will be used by the Myri-10G Ethernet
driver to post requests to the NIC. This driver will be submitted soon.
__iowrite64_copy copies to I/O memory in units of 64 bits when possible (on
64 bit architectures). It reverts to __iowrite32_copy on 32 bit
architectures.
* git://git.kernel.org/pub/scm/linux/kernel/git/bcollins/linux1394-2.6: (28 commits)
eth1394: replace __constant_htons by htons
ieee1394: adjust code formatting in highlevel.c
ieee1394: hl_irqs_lock is taken in hardware interrupt context
ieee1394_core: switch to kthread API
ieee1394: sbp2: Kconfig fix
ieee1394: add preprocessor constant for invalid csr address
sbp2: fix deregistration of status fifo address space
[PATCH] eth1394: endian fixes
Fix broken suspend/resume in ohci1394
sbp2: use __attribute__((packed)) for on-the-wire structures
sbp2: provide helptext for CONFIG_IEEE1394_SBP2_PHYS_DMA and mark it experimental
Update feature removal of obsolete raw1394 ISO requests.
sbp2: fix S800 transfers if phys_dma is off
sbp2: remove ohci1394 specific constant
ohci1394: make phys_dma parameter read-only
ohci1394: set address range properties
ieee1394: extend lowlevel API for address range properties
sbp2: log number of supported concurrent logins
sbp2: remove manipulation of inquiry response
ieee1394: save RAM by using a single tlabel for broadcast transactions
...
Linus Torvalds [Wed, 21 Jun 2006 02:44:03 +0000 (19:44 -0700)]
Fix up CFQ scheduler for recent rbtree node shrinkage
The color is now in the low bits of the parent pointer, and initializing
it to 0 happens as part of the whole memset above, so just remove the
unnecessary RB_CLEAR_COLOR.
Herbert Xu [Wed, 21 Jun 2006 00:53:54 +0000 (10:53 +1000)]
[FORCEDETH] Fix xmit_lock/netif_tx_lock after merge
There has been an update to the forcedeth driver that added a few new
uses of xmit_lock which is no longer meant to be used directly. This
patch replaces them with netif_tx_lock_bh.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Tue, 20 Jun 2006 22:38:12 +0000 (15:38 -0700)]
Merge branch 'rio.b19' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/bird
* 'rio.b19' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/bird:
[PATCH] missing readb/readw in rio
[PATCH] copy_to_user() from iomem is a bad thing
[PATCH] forgotten swap of copyout() arguments
[PATCH] handling rio MEMDUMP
[PATCH] fix rio_copy_to_card() for OLDPCI case
[PATCH] uses of ->Copy() in rioroute are bogus
[PATCH] bogus order of copy_from_user() arguments
[PATCH] rio ->Copy() expects the sourse as first argument
[PATCH] trivial annotations in rio
Linus Torvalds [Tue, 20 Jun 2006 22:10:08 +0000 (15:10 -0700)]
Merge git://git.infradead.org/hdrcleanup-2.6
* git://git.infradead.org/hdrcleanup-2.6: (63 commits)
[S390] __FD_foo definitions.
Switch to __s32 types in joystick.h instead of C99 types for consistency.
Add <sys/types.h> to headers included for userspace in <linux/input.h>
Move inclusion of <linux/compat.h> out of user scope in asm-x86_64/mtrr.h
Remove struct fddi_statistics from user view in <linux/if_fddi.h>
Move user-visible parts of drivers/s390/crypto/z90crypt.h to include/asm-s390
Revert include/media changes: Mauro says those ioctls are only used in-kernel(!)
Include <linux/types.h> and use __uXX types in <linux/cramfs_fs.h>
Use __uXX types in <linux/i2o_dev.h>, include <linux/ioctl.h> too
Remove private struct dx_hash_info from public view in <linux/ext3_fs.h>
Include <linux/types.h> and use __uXX types in <linux/affs_hardblocks.h>
Use __uXX types in <linux/divert.h> for struct divert_blk et al.
Use __u32 for elf_addr_t in <asm-powerpc/elf.h>, not u32. It's user-visible.
Remove PPP_FCS from user view in <linux/ppp_defs.h>, remove __P mess entirely
Use __uXX types in user-visible structures in <linux/nbd.h>
Don't use 'u32' in user-visible struct ip_conntrack_old_tuple.
Use __uXX types for S390 DASD volume label definitions which are user-visible
S390 BIODASDREADCMB ioctl should use __u64 not u64 type.
Remove unneeded inclusion of <linux/time.h> from <linux/ufs_fs.h>
Fix private integer types used in V4L2 ioctls.
...
Manually resolve conflict in include/linux/mtd/physmap.h
Linus Torvalds [Tue, 20 Jun 2006 21:51:22 +0000 (14:51 -0700)]
Merge git://git.infradead.org/~dwmw2/rbtree-2.6
* git://git.infradead.org/~dwmw2/rbtree-2.6:
[RBTREE] Switch rb_colour() et al to en_US spelling of 'color' for consistency
Update UML kernel/physmem.c to use rb_parent() accessor macro
[RBTREE] Update hrtimers to use rb_parent() accessor macro.
[RBTREE] Add explicit alignment to sizeof(long) for struct rb_node.
[RBTREE] Merge colour and parent fields of struct rb_node.
[RBTREE] Remove dead code in rb_erase()
[RBTREE] Update JFFS2 to use rb_parent() accessor macro.
[RBTREE] Update eventpoll.c to use rb_parent() accessor macro.
[RBTREE] Update key.c to use rb_parent() accessor macro.
[RBTREE] Update ext3 to use rb_parent() accessor macro.
[RBTREE] Change rbtree off-tree marking in I/O schedulers.
[RBTREE] Add accessor macros for colour and parent fields of rb_node
Linus Torvalds [Tue, 20 Jun 2006 21:50:31 +0000 (14:50 -0700)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6: (199 commits)
[MTD] NAND: Fix breakage all over the place
[PATCH] NAND: fix remaining OOB length calculation
[MTD] NAND Fixup NDFC merge brokeness
[MTD NAND] S3C2410 driver cleanup
[MTD NAND] s3c24x0 board: Fix clock handling, ensure proper initialisation.
[JFFS2] Check CRC32 on dirent and data nodes each time they're read
[JFFS2] When retiring nextblock, allocate a node_ref for the wasted space
[JFFS2] Mark XATTR support as experimental, for now
[JFFS2] Don't trust node headers before the CRC is checked.
[MTD] Restore MTD_ROM and MTD_RAM types
[MTD] assume mtd->writesize is 1 for NOR flashes
[MTD NAND] Fix s3c2410 NAND driver so it at least _looks_ like it compiles
[MTD] Prepare physmap for 64-bit-resources
[JFFS2] Fix more breakage caused by janitorial meddling.
[JFFS2] Remove stray __exit from jffs2_compressors_exit()
[MTD] Allow alternate JFFS2 mount variant for root filesystem.
[MTD] Disconnect struct mtd_info from ABI
[MTD] replace MTD_RAM with MTD_GENERIC_TYPE
[MTD] replace MTD_ROM with MTD_GENERIC_TYPE
[MTD] remove a forgotten MTD_XIP
...
Linus Torvalds [Tue, 20 Jun 2006 21:49:00 +0000 (14:49 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
[ARM] 3559/1: S3C2442: core and serial port
[ARM] 3557/1: S3C24XX: centralise and cleanup uart registration
[ARM] 3558/1: SMDK24XX: LED platform devices
[ARM] 3534/1: add spi support to lubbock platform
[ARM] 3554/1: ARM: Fix dyntick locking
[ARM] 3553/1: S3C24XX: earlier print of cpu idcode info
[ARM] 3552/1: S3C24XX: Move VA of GPIO for low-level debug
[ARM] 3551/1: S3C24XX: PM code failes to compile with CONFIG_DCACHE_WRITETHROUGH
[ARM] 3550/1: OSIRIS: fix serial port map for 1:1
[ARM] 3548/1: Fix the ARMv6 CPU id in compressed/head.S
[ARM] 3335/1: Old-abi Thumb sys_syscall broken
[ARM] 3467/1: [3/3] Support for Philips PNX4008 platform: defconfig
[ARM] 3466/1: [2/3] Support for Philips PNX4008 platform: chip support
[ARM] 3465/1: [1/3] Support for Philips PNX4008 platform: headers
[ARM] 3407/1: lpd7x: documetation update
[ARM] 3406/1: lpd7x: compilation fix for smc91x
[ARM] 3405/1: lpd7a40x: CPLD ssp driver
[ARM] 3404/1: lpd7a40x: AMBA CLCD support
[ARM] 3403/1: lpd7a40x: updated default configurations
[ARM] 3402/1: lpd7a40x: serial driver bug fix
...
Thomas Gleixner [Tue, 20 Jun 2006 18:05:05 +0000 (20:05 +0200)]
[MTD] NAND: Fix breakage all over the place
Following problems are addressed:
- wrong status caused early break out of nand_wait()
- removed the bogus status check in nand_wait() which
is a relict of the abandoned support for interrupted
erase.
- status check moved to the correct place in read_oob
- oob support for syndrom based ecc with strange layouts
- use given offset in the AUTOOOB based oob operations
Partially based on a patch from Vitaly Vool <vwool@ru.mvista.com>
Thanks to Savin Zlobec <savin@epico.si> for tracking down the
status problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In nand_read_page_syndrome/nand_write_page_syndrome the calculation of
the remaining oob length which is not used by the prepad/ecc/postpad
areas is wrong.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Andrew Victor [Tue, 20 Jun 2006 18:30:20 +0000 (19:30 +0100)]
[ARM] 3607/1: AT91RM9200 misc fixes
Patch from Andrew Victor
This final patch includes some general fixes.
1. Link in pm.o if CONFIG_PM is enabled. [Should have been included in
patch 3605/1].
2. Use __raw_readl()/__raw_writel() when accessing System Peripheral
registers.
3. Removed some unnecessary includes
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor [Tue, 20 Jun 2006 18:30:19 +0000 (19:30 +0100)]
[ARM] 3605/1: AT91RM9200 Power Management
Patch from Andrew Victor
This patch adds the core Power Management support for the AT91RM9200
processor. It will support suspend-to-RAM and standby modes.
The suspend-to-RAM functionality is not 100% complete. The code that
needs to be execute from the internal SRAM to restore the system is
outstanding. For now we just fall through to Standby mode.
The AT91-specific at91_suspend_entering_slow_clock() function will
eventually be replaced by clk_must_disable() once that functionality is
added to mainline clock API.
Patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor [Tue, 20 Jun 2006 18:27:34 +0000 (19:27 +0100)]
[ARM] 3603/1: AT91RM9200 remove old files
Patch from Andrew Victor
This patch removes the now unnecessary
include/asm-arm/arch-at91rm9200/pio.h file. The pin configuration is
now handled in the platform-device setup code
(arch/arm/mach-at91rm9200/devices.c).
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Steve Grubb [Mon, 12 Jun 2006 11:48:28 +0000 (07:48 -0400)]
[PATCH] make set_loginuid obey audit_enabled
Hi,
I was doing some testing and noticed that when the audit system was disabled,
I was still getting messages about the loginuid being set. The following patch
makes audit_set_loginuid look at in_syscall to determine if it should create
an audit event. The loginuid will continue to be set as long as there is a context.
Signed-off-by: Steve Grubb <sgrubb@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Amy Griffis [Fri, 9 Jun 2006 03:19:31 +0000 (23:19 -0400)]
[PATCH] log more info for directory entry change events
When an audit event involves changes to a directory entry, include
a PATH record for the directory itself. A few other notable changes:
- fixed audit_inode_child() hooks in fsnotify_move()
- removed unused flags arg from audit_inode()
- added audit log routines for logging a portion of a string
In this implementation, audit registers inotify watches on the parent
directories of paths specified in audit rules. When audit's inotify
event handler is called, it updates any affected rules based on the
filesystem event. If the parent directory is renamed, removed, or its
filesystem is unmounted, audit removes all rules referencing that
inotify watch.
To keep things simple, this implementation limits location-based
auditing to the directory entries in an existing directory. Given
a path-based rule for /foo/bar/passwd, the following table applies:
passwd modified -- audit event logged
passwd replaced -- audit event logged, rules list updated
bar renamed -- rule removed
foo renamed -- untracked, meaning that the rule now applies to
the new location
Audit users typically want to have many rules referencing filesystem
objects, which can significantly impact filtering performance. This
patch also adds an inode-number-based rule hash to mitigate this
situation.
The patch is relative to the audit git tree:
http://kernel.org/git/?p=linux/kernel/git/viro/audit-current.git;a=summary
and uses the inotify kernel API:
http://lkml.org/lkml/2006/6/1/145
Signed-off-by: Amy Griffis <amy.griffis@hp.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
George C. Wilson [Wed, 24 May 2006 21:09:55 +0000 (16:09 -0500)]
[PATCH] Audit of POSIX Message Queue Syscalls v.2
This patch adds audit support to POSIX message queues. It applies cleanly to
the lspp.b15 branch of Al Viro's git tree. There are new auxiliary data
structures, and collection and emission routines in kernel/auditsc.c. New hooks
in ipc/mqueue.c collect arguments from the syscalls.
I tested the patch by building the examples from the POSIX MQ library tarball.
Build them -lrt, not against the old MQ library in the tarball. Here's the URL:
http://www.geocities.com/wronski12/posix_ipc/libmqueue-4.41.tar.gz
Do auditctl -a exit,always -S for mq_open, mq_timedsend, mq_timedreceive,
mq_notify, mq_getsetattr. mq_unlink has no new hooks. Please see the
corresponding userspace patch to get correct output from auditd for the new
record types.
[fixes folded]
Signed-off-by: George Wilson <ltcgcw@us.ibm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linda Knippers [Wed, 17 May 2006 02:03:48 +0000 (22:03 -0400)]
[PATCH] update of IPC audit record cleanup
The following patch addresses most of the issues with the IPC_SET_PERM
records as described in:
https://www.redhat.com/archives/linux-audit/2006-May/msg00010.html
and addresses the comments I received on the record field names.
To summarize, I made the following changes:
1. Changed sys_msgctl() and semctl_down() so that an IPC_SET_PERM
record is emitted in the failure case as well as the success case.
This matches the behavior in sys_shmctl(). I could simplify the
code in sys_msgctl() and semctl_down() slightly but it would mean
that in some error cases we could get an IPC_SET_PERM record
without an IPC record and that seemed odd.
2. No change to the IPC record type, given no feedback on the backward
compatibility question.
3. Removed the qbytes field from the IPC record. It wasn't being
set and when audit_ipc_obj() is called from ipcperms(), the
information isn't available. If we want the information in the IPC
record, more extensive changes will be necessary. Since it only
applies to message queues and it isn't really permission related, it
doesn't seem worth it.
4. Removed the obj field from the IPC_SET_PERM record. This means that
the kern_ipc_perm argument is no longer needed.
5. Removed the spaces and renamed the IPC_SET_PERM field names. Replaced iuid and
igid fields with ouid and ogid in the IPC record.
I tested this with the lspp.22 kernel on an x86_64 box. I believe it
applies cleanly on the latest kernel.
-- ljk
Signed-off-by: Linda Knippers <linda.knippers@hp.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Just a few minor proposed updates. Only the last one will
actually affect behavior. The rest are just misleading
code.
Several AUDIT_SET functions return 'old' value, but only
return value <0 is checked for. So just return 0.
propagate audit_set_rate_limit and audit_set_backlog_limit
error values
In audit_buffer_free, the audit_freelist_count was being
incremented even when we discard the return buffer, so
audit_freelist_count can end up wrong. This could cause
the actual freelist to shrink over time, eventually
threatening to degrate audit performance.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Mon, 22 May 2006 05:09:24 +0000 (01:09 -0400)]
[PATCH] fix deadlocks in AUDIT_LIST/AUDIT_LIST_RULES
We should not send a pile of replies while holding audit_netlink_mutex
since we hold the same mutex when we receive commands. As the result,
we can get blocked while sending and sit there holding the mutex while
auditctl is unable to send the next command and get around to receiving
what we'd sent.
Solution: create skb and put them into a queue instead of sending;
once we are done, send what we've got on the list. The former can
be done synchronously while we are handling AUDIT_LIST or AUDIT_LIST_RULES;
we are holding audit_netlink_mutex at that point. The latter is done
asynchronously and without messing with audit_netlink_mutex.
projects / linux-2.6 / log