Nick Piggin [Fri, 30 Sep 2005 16:34:42 +0000 (02:34 +1000)]
[PATCH] i386: include linux/irq.h rather than asm/hw_irq.h
I need the following patch to compile -git8 here, otherwise these
files fail to compile (asm/hw_irq.h needs definitions from
linux/irq.h and that file provides the required include ordering).
I did not do a full audit, though there looks to be many other
places that should get the same treatment, if this is the right
way to do it.
Al Viro [Fri, 30 Sep 2005 02:36:50 +0000 (03:36 +0100)]
[PATCH] bogus BUILD_BUG_ON() in bpa_iommu
BUILD_BUG_ON(1) is asking for trouble (and getting it) when used in that
manner - dead code elimination happens after we parse it and invalid
type is invalid type, dead code or not.
It might be version-dependent, but at least 4.0.1 refuses to accept
that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gen FUKATSU [Fri, 30 Sep 2005 15:09:17 +0000 (16:09 +0100)]
[ARM] 2940/1: Fix BTB entry flush in arch/arm/mm/cache-v6.S
Patch from Gen FUKATSU
Invalidate BTB entry instruction flushes two instruction
at a time. Therefore this instruction should be done four
times after invalidate instruction cache line.
Signed-off-by: Gen Fukatsu Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 2939/1: Fix compilation error in arch/arm/mm/flush.c
Patch from Catalin Marinas
When CONFIG_CPU_CACHE_VIPT is defined, the flush_pfn_alias() function is
implicitely declared and it later conflicts with its actual definition.
This patch moves the function definition to the beginning of the file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David S. Miller [Fri, 30 Sep 2005 01:50:34 +0000 (18:50 -0700)]
[SPARC64]: Fix several bugs in flush_ptrace_access().
1) Use cpudata cache line sizes, not magic constants.
2) Align start address in cheetah case so we do not get
unaligned address traps. (pgrep was good at triggering
this, via /proc/${pid}/cmdline accesses)
Signed-off-by: David S. Miller <davem@davemloft.net>
[TCP]: Don't over-clamp window in tcp_clamp_window()
From: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Handle better the case where the sender sends full sized
frames initially, then moves to a mode where it trickles
out small amounts of data at a time.
This known problem is even mentioned in the comments
above tcp_grow_window() in tcp_input.c, specifically:
...
* The scheme does not work when sender sends good segments opening
* window and then starts to feed us spagetti. But it should work
* in common situations. Otherwise, we have to rely on queue collapsing.
...
When the sender gives full sized frames, the "struct sk_buff" overhead
from each packet is small. So we'll advertize a larger window.
If the sender moves to a mode where small segments are sent, this
ratio becomes tilted to the other extreme and we start overrunning
the socket buffer space.
tcp_clamp_window() tries to address this, but it's clamping of
tp->window_clamp is a wee bit too aggressive for this particular case.
Fix confirmed by Ion Badulescu.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kuznetsov has explained the situation as follows:
--------------------
I think the fix is incorrect. Look, the RFC function init_cwnd(mss) is
not continuous: f.e. for mss=1095 it needs initial window 1095*4, but
for mss=1096 it is 1096*3. We do not know exactly what mss sender used
for calculations. If we advertised 1096 (and calculate initial window
3*1096), the sender could limit it to some value < 1096 and then it
will need window his_mss*4 > 3*1096 to send initial burst.
See?
So, the honest function for inital rcv_wnd derived from
tcp_init_cwnd() is:
init_rcv_wnd(mss)=
min { init_cwnd(mss1)*mss1 for mss1 <= mss }
It is something sort of:
if (mss < 1096)
return mss*4;
if (mss < 1096*2)
return 1096*4;
return mss*2;
(I just scrablled a graph of piece of paper, it is difficult to see or
to explain without this)
I selected it differently giving more window than it is strictly
required. Initial receive window must be large enough to allow sender
following to the rfc (or just setting initial cwnd to 2) to send
initial burst. But besides that it is arbitrary, so I decided to give
slack space of one segment.
Actually, the logic was:
If mss is low/normal (<=ethernet), set window to receive more than
initial burst allowed by rfc under the worst conditions
i.e. mss*4. This gives slack space of 1 segment for ethernet frames.
For msses slighlty more than ethernet frame, take 3. Try to give slack
space of 1 frame again.
If mss is huge, force 2*mss. No slack space.
Value 1460*3 is really confusing. Minimal one is 1096*2, but besides
that it is an arbitrary value. It was meant to be ~4096. 1460*3 is
just the magic number from RFC, 1460*3 = 1095*4 is the magic :-), so
that I guess hands typed this themselves.
--------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
[ARM] 2941/1: Fix running legacy binaries from a soft-float root filesystem with CONFIG_IWMMXT.
Patch from Daniel Jacobowitz
Thread flags are inherited on fork(). In order for a binary which has
the iWMMXt coprocessor enabled to run a binary which needs the FPA
emulation, we need to explicitly clear TIF_USING_IWMMXT if we are not
going to set it.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SMU driver has a small mistake in the locking of the interrupt code,
if polled access and interrupt access race, interrupt may take a lock
and return without releasing it. This fixes it. With that patch, the
driver is rock solid with my experimental thermal control (which bangs
it pretty hard) racing with real time clock and cpufreq handling.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] readv/writev syscalls are not checked by lsm
it seems that readv(2)/writev(2) syscalls do not call
file_permission callback. Looks like this is overlook.
I have filled the issue into redhat bugzilla as
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=169433
and got the recommendation to post this on lsm mailing list.
The following trivial patch solves the problem.
Signed-off-by: Kostik Belousov <kostikbel@gmail.com> Signed-off-by: Chris Wright <chrisw@osdl.org>
Mike Waychison [Thu, 29 Sep 2005 22:01:27 +0000 (00:01 +0200)]
[PATCH] x86_64: Fix mce_log
The attempt to fixup the lockless mce log buffer introduced an infinite loop
when trying to find a free entry.
And:
Using rcu_dereference() to load mcelog.next doesn't seem to be sufficient
enough to ensure that mcelog.next is loaded each time around the loop in
mce_log(). Instead, use an explicit rmb() to ensure that the compiler gets it
right.
AK: turned the smp_wmbs into true wmbs to make sure they are not
reordered by the compiler on UP.
Roland McGrath [Thu, 29 Sep 2005 21:54:42 +0000 (14:54 -0700)]
[PATCH] Fix task state testing properly in do_signal_stop()
Any tests using < TASK_STOPPED or the like are left over from the time
when the TASK_ZOMBIE and TASK_DEAD bits were in the same word, and it
served to check for "stopped or dead". I think this one in
do_signal_stop is the only such case. It has been buggy ever since
exit_state was separated, and isn't testing the exit_state value.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roland points out that the flags end up having non-obvious dependencies
elsewhere, so revert aa55a08687059aa169d10a313c41f238c2070488 and add
some comments about why things are as they are.
We'll just have to fix up the broken comparisons. Roland has a patch.
[PATCH] fix TASK_STOPPED vs TASK_NONINTERACTIVE interaction
do_signal_stop:
for_each_thread(t) {
if (t->state < TASK_STOPPED)
++sig->group_stop_count;
}
However, TASK_NONINTERACTIVE > TASK_STOPPED, so this loop will not
count TASK_INTERRUPTIBLE | TASK_NONINTERACTIVE threads.
See also wait_task_stopped(), which checks ->state > TASK_STOPPED.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
[ We really probably should always use the appropriate bitmasks to test
task states, not do it like this. Using something like
and then doing "if (task->state & TASK_RUNNABLE)" or similar. But the
ordering of the task states is historical, and keeping the ordering
does make sense regardless. ]
[PATCH] intelfb: Fix regression (blank display) from ioremap patch
- Workaround for the ioremap patch that produces a blank display on some
chipsets
- Make hwcursor = 0 the default. The hardware cursor does not work with all
hardware.
Al Viro [Wed, 28 Sep 2005 23:31:14 +0000 (00:31 +0100)]
[PATCH] ppc32 ld.script fix for building on ppc64
In arch/ppc/boot/ld.script we need OUTPUT_ARCH(powerpc:common) for the
same reasons why we need it in vmlinux.lds.S; when we build on ppc64
box, we need to be explicit about the target.
See http://linus.bkbits.net:8080/linux-2.5/cset@1.1784.8.10 for the
corresponding fix in vmlinux.lds.S.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Wed, 28 Sep 2005 21:27:23 +0000 (22:27 +0100)]
[PATCH] uml makefiles sanitized
UML makefiles sanitized:
- number of generated headers reduced to 2 (from user-offsets.c and
kernel-offsets.c resp.). The rest is made constant and simply
includes those two.
- mk_... helpers are gone now that we don't need to generate these
headers
- arch/um/include2 removed since everything under arch/um/include/sysdep
is constant now and symlink can point straight to source tree.
- dependencies seriously simplified.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Russell King [Thu, 29 Sep 2005 08:44:54 +0000 (09:44 +0100)]
[ARM] pxafb: Remove #if DEBUG, convert DPRINTK to pr_debug
Fix warning:
drivers/video/pxafb.h:119:5: warning: "DEBUG" is not defined
by removing the whole
#if DEBUG
#define DPRINTK(fmt, args...) printk...etc...
#else
#define DPRINTK(fmt, args...)
#endif
stuff - we have pr_debug() for this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David S. Miller [Thu, 29 Sep 2005 04:06:47 +0000 (21:06 -0700)]
[SPARC64]: Simplify user fault fixup handling.
Instead of doing byte-at-a-time user accesses to figure
out where the fault occurred, read the saved fault_address
from the current thread structure.
For the sake of defensive programming, if the fault_address
does not fall into the user buffer range, simply assume the
whole area faulted. This will cause the fixup for
copy_from_user() to clear the entire kernel side buffer.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 29 Sep 2005 03:41:45 +0000 (20:41 -0700)]
[SPARC64]: Fix fault handling in unaligned trap handler.
We were not calling kernel_mna_trap_fault() correctly.
Instead of being fancy, just return 0 vs. -EFAULT from
the assembler stubs, and handle that return value as
appropriate.
Create an "__retl_efault" stub for assembler exception
table entries and use it where possible.
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 28 Sep 2005 16:03:15 +0000 (17:03 +0100)]
[PATCH] Keys: Add possessor permissions to keys [try #3]
The attached patch adds extra permission grants to keys for the possessor of a
key in addition to the owner, group and other permissions bits. This makes
SUID binaries easier to support without going as far as labelling keys and key
targets using the LSM facilities.
This patch adds a second "pointer type" to key structures (struct key_ref *)
that can have the bottom bit of the address set to indicate the possession of
a key. This is propagated through searches from the keyring to the discovered
key. It has been made a separate type so that the compiler can spot attempts
to dereference a potentially incorrect pointer.
The "possession" attribute can't be attached to a key structure directly as
it's not an intrinsic property of a key.
Pointers to keys have been replaced with struct key_ref *'s wherever
possession information needs to be passed through.
This does assume that the bottom bit of the pointer will always be zero on
return from kmem_cache_alloc().
The key reference type has been made into a typedef so that at least it can be
located in the sources, even though it's basically a pointer to an undefined
type. I've also renamed the accessor functions to be more useful, and all
reference variables should now end in "_ref".
Signed-Off-By: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In kmalloc_node we are checking if the allocation is for the same node when
interrupts are "on". This may lead to an allocation on another node than
intended.
This patch just shifts the check for the current node in __cache_alloc_node
when interrupts are disabled.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com> Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My previous patch fixing invalidation of huge PTEs wasn't good enough, we
still had an issue if a PTE invalidation batch contained both small and
large pages. This patch fixes this by making sure the batch is flushed if
the page size fed to it changes.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When creating a multipath device, if the queue_if_no_path parameter is
specified it gets ignored.
While the queue_if_no_path variable is correctly set to 1, the
saved_queue_if_no_path gets set to 0. When the device is subsequently made
live (resumed), the saved value (0) always overwrites the live value (1) so
the option *always* gets turned off.
The fix adds a parameter to the queue_if_no_path() function to indicate
whether the previous value should be preserved or not - if not, as when the
device is being set up, the saved value is set to the new value (1).
Signed-Off-By: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
goggin, edward [Wed, 28 Sep 2005 04:45:44 +0000 (21:45 -0700)]
[PATCH] device-mapper: Trigger an event when a table is deleted
If anything is waiting on a device's table when the device is removed, we
must first wake it up so it will release its reference. Otherwise the
table's reference count will not drop to zero and the table will not get
removed.
Signed-Off-By: Alasdair G Kergon <agk@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] swsusp: avoid problems if there are too many pages to save
The following patch makes swsusp avoid problems during resume if there are
too many pages to save on suspend. It adds a constant that allows us to
verify if we are going to save too many pages and implements the check
(this is done as early as we can tell that the check will trigger, which is
in swsusp_alloc()).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] orinoco: Fix flood of kernel log with stupid WE warnings
Latest wireless extensions moved a field from netdev -> wireless_handlers.
The WE core will now printk a warning on every call to get_wireless_stats()
on a driver that still uses the old field. This patch fixes orinoco.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Anton Blanchard [Wed, 28 Sep 2005 04:45:38 +0000 (21:45 -0700)]
[PATCH] ppc64: Add missing barrier() in kexec code
Mikey and I were testing kexec and hit a lockup. It turns out gcc 4.0
optimises the kexec_prepare_cpus loop so we avoid reloading paca.hw_cpu_id.
A gcc barrier() fixes the problem.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Wed, 28 Sep 2005 04:45:37 +0000 (21:45 -0700)]
[PATCH] cpuset maintainers
Specify the cpuset maintainers.
Signed-off-by: Paul Jackson <pj@sgi.com> Signed-off-by: Simon Derr <simon.derr@bull.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
john stultz [Wed, 28 Sep 2005 04:45:36 +0000 (21:45 -0700)]
[PATCH] x86-64: Fix bad assumption that dualcore cpus have synced TSCs
This should resolve the issue seen in bugme bug #5105, where it is assumed
that dualcore x86_64 systems have synced TSCs. This is not the case, and
alternate timesources should be used instead.
For more details, see:
http://bugzilla.kernel.org/show_bug.cgi?id=5105
Andi's earlier concerns that the TSCs should be synced on dualcore systems
have been resolved by confirmation from AMD folks that they can be
unsynced.
Rusty Russell [Wed, 28 Sep 2005 04:45:34 +0000 (21:45 -0700)]
[PATCH] Ignore trailing whitespace on kernel parameters correctly
Dave Jones says:
... if the modprobe.conf has trailing whitespace, modules fail to load
with the following helpful message..
snd_intel8x0: Unknown parameter `'
Previous version truncated last argument.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prevent swsusp from leaking some memory in case of an error in
read_pagedir(). It also prevents the BUG_ON() from triggering if there's
an error while reading swap.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch removes some wrong code from the data_free() function
in swsusp.
This function could only be called if there's an error while writing the
suspend image to swap, so it is not triggered easily. However, if
triggered, it would probably corrupt some memory.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jon Burgess [Wed, 28 Sep 2005 04:45:26 +0000 (21:45 -0700)]
[PATCH] dvb: fix NULL pointer dereference when loading the budget-av module
Ralph Metzler wrote:
> AFAIR, there is a bug in tda10021.c in tda10021_readreg() which
> references state->frontend.dvb->num
> This is fatal if the frontend is not at the probed address and thus
> not yet registered (no dvb entry set yet -> NULL pointer ...).
The attached patch should get rid of the oops.
Signed-off-by: Jon Burgess <jburgess@uklinux.net> Cc: Johannes Stezenbach <js@linuxtv.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fid management cleanup. The patch attempts to fix the races in dentry's
fid management.
Dentries don't keep the opened fids anymore, they are moved to the file
structs. Ideally there should be no more than one fid with fidcreate equal
to zero in the dentry's list of fids.
v9fs_fid_create initializes the important fields (fid, fidcreated) before
v9fs_fid is added to the list. v9fs_fid_lookup returns only fids that are
not created by v9fs_create. v9fs_fid_get_created returns the fid created
by the same process by v9fs_create (if any) and removes it from dentry's
list
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net> Cc: Eric Van Hensbergen <ericvh@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chris Sykes [Wed, 28 Sep 2005 04:45:23 +0000 (21:45 -0700)]
[PATCH] Fix ext3_new_inode() failure paths
Fix failure paths in ext3_new_inode() and clean up duplicated code: -
DQUOT_DROP() was not being called if ext3_init_security() failed.
Signed-off-by: Chris Sykes <chris@sigsegv.plus.com> Cc: Stephen Smalley <sds@epoch.ncsc.mil> Cc: Jan Kara <jack@ucw.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chris Sykes [Wed, 28 Sep 2005 04:45:22 +0000 (21:45 -0700)]
[PATCH] Fix ext2_new_inode() failure paths
Fix failure paths in ext2_new_inode() and clean up duplicated code: -
DQUOT_DROP() was not being called if ext2_init_security() failed.
Signed-off-by: Chris Sykes <chris@sigsegv.plus.com> Cc: Stephen Smalley <sds@epoch.ncsc.mil> Cc: Jan Kara <jack@ucw.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6 / log