In STA mode, the AP will echo our traffic. This includes multicast
traffic.
Receiving these frames confuses some protocols and applications,
notably IPv6 Duplicate Address Detection.
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:55 +0000 (17:01 -0400)]
[MAC80211]: clean up whitespace
This cleans up some whitespace to make the mac80211
version in mainline diverge less from wireless-dev.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:55 +0000 (17:01 -0400)]
[MAC80211]: fix preamble setting
It looks like in commit 28487a90 the condition was unintentionally
negated by moving some code, fix it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Daniel Drake <dsd@gentoo.org> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Larry Finger [Tue, 28 Aug 2007 21:01:55 +0000 (17:01 -0400)]
[MAC80211]: Remove overly sticky averaging filters for rssi, signal, noise
The current version of wireless statistics contains a bug in the averaging
that makes the numbers be too sticky and not react to small changes. This
patch removes all averaging.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Jiri Benc <jbenc@suse.cz> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:55 +0000 (17:01 -0400)]
[MAC80211]: add interface index to key debugfs
Add a new file 'ifindex' to each key's debugfs dir to
allow finding which interface the key was configured on.
This isn't done as a symlink because of possible netdev
name changes.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:55 +0000 (17:01 -0400)]
[MAC80211]: rework key handling
This moves all the key handling code out from ieee80211_ioctl.c
into key.c and also does the following changes including documentation
updates in mac80211.h:
1) Turn off hardware acceleration for keys when the interface
is down. This is necessary because otherwise monitor
interfaces could be decrypting frames for other interfaces
that are down at the moment. Also, it should go some way
towards better suspend/resume support, in any case the
routines used here could be used for that as well.
Additionally, this makes the driver interface nicer, keys
for a specific local MAC address are only ever present
while an interface with that MAC address is enabled.
2) Change driver set_key() callback interface to allow only
return values of -ENOSPC, -EOPNOTSUPP and 0, warn on all
other return values. This allows debugging the stack when
a driver notices it's handed a key while it is down.
3) Invert the flag meaning to KEY_FLAG_UPLOADED_TO_HARDWARE.
4) Remove REMOVE_ALL_KEYS command as it isn't used nor do we
want to use it, we'll use DISABLE_KEY for each key. It is
hard to use REMOVE_ALL_KEYS because we can handle multiple
virtual interfaces with different key configuration, so we'd
have to keep track of a lot of state for this and that isn't
worth it.
5) Warn when disabling a key fails, it musn't.
6) Remove IEEE80211_HW_NO_TKIP_WMM_HWACCEL in favour of per-key
IEEE80211_KEY_FLAG_WMM_STA to let driver sort it out itself.
7) Tell driver that a (non-WEP) key is used only for transmission
by using an all-zeroes station MAC address when configuring.
8) Change the set_key() callback to have access to the local MAC
address the key is being added for.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:55 +0000 (17:01 -0400)]
[MAC80211]: remove fake set_key() call
Remove adding a fake key with a NONE key algorithm for each
associated STA. If we have hardware with such TX filtering
we should probably extend the sta_table_notification()
callback with the sta information instead; the fact that
it's treated as a key for some atheros hardware shouldn't
bother the stack.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:54 +0000 (17:01 -0400)]
[MAC80211] key handling: remove default_wep_only
Remove the default_wep_only stuff, this wasn't really done well
and no current driver actually cares.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:54 +0000 (17:01 -0400)]
[MAC80211]: remove krefs for keys
they aren't really refcounted anyway
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:54 +0000 (17:01 -0400)]
[MAC80211]: embed key conf in key, fix driver interface
This patch embeds the struct ieee80211_key_conf into struct ieee80211_key
and thus avoids allocations and having data present twice.
This required some more changes:
1) The removal of the IEEE80211_KEY_DEFAULT_TX_KEY key flag.
This flag isn't used by drivers nor should it be since
we have a set_key_idx() callback. Maybe that callback needs
to be extended to include the key conf, but only a driver that
requires it will tell.
2) The removal of the IEEE80211_KEY_DEFAULT_WEP_ONLY key flag.
This flag is global, so it shouldn't be passed in the key
conf structure. Pass it to the function instead.
Also, this patch removes the AID parameter to the set_key() callback
because it is currently unused and the hardware currently cannot know
about the AID anyway. I suspect this was used with some hardware that
actually selected the AID itself, but that functionality was removed.
Additionally, I've removed the ALG_NULL key algorithm since we have
ALG_NONE.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Tue, 28 Aug 2007 21:01:54 +0000 (17:01 -0400)]
[MAC80211]: Remove bitfields from struct ieee80211_sub_if_data
mac80211, remove bitfields from struct ieee80211_sub_if_data
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Tue, 28 Aug 2007 21:01:54 +0000 (17:01 -0400)]
[MAC80211]: Remove bitfields from struct ieee80211_if_sta
mac80211, remove bitfields from struct ieee80211_if_sta
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Tue, 28 Aug 2007 21:01:54 +0000 (17:01 -0400)]
[MAC80211]: Remove bitfields from struct ieee80211_txrx_data
mac80211, remove bitfields from struct ieee80211_txrx_data
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Tue, 28 Aug 2007 21:01:54 +0000 (17:01 -0400)]
[MAC80211]: Remove bitfields from struct ieee80211_tx_packet_data
remove bitfields from struct ieee80211_tx_packet_data
[Johannes: completely clear flags in ieee80211_remove_tx_extra]
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:54 +0000 (17:01 -0400)]
[MAC80211]: use switch statement in tx code
The transmit code needs to set the addresses depending on the
interface type, a likely() for AP/VLAN is quite wrong since
most people will be using STA; convert to a switch statement
to make it look nicer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:53 +0000 (17:01 -0400)]
[MAC80211]: refactor event sending
Create a new file event.c that will contain code to send mac/mlme
events to userspace. For now put the Michael MIC failure condition
into it and remove sending of that condition via the management
interface, hostapd interestingly doesn't do anything when it gets
such a packet besides printing a message, it reacts only on the
private iwevent.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:53 +0000 (17:01 -0400)]
[MAC80211]: kill key_mgmt, use key_management_enabled
The key_mgmt variable for STA interfaces doesn't seem well-defined
nor do we actually use the values other than "NONE", so change it to
be named better.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:53 +0000 (17:01 -0400)]
[MAC80211]: remove unused ioctls (3)
The ioctls
* PRISM2_PARAM_RADAR_DETECT
* PRISM2_PARAM_SPECTRUM_MGMT
are not used by hostapd or wpa_supplicant,
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:53 +0000 (17:01 -0400)]
[MAC80211]: fix software decryption
When doing key selection for software decryption, mac80211 gets
a few things wrong: it always uses pairwise keys if configured,
even if the frame is addressed to a multicast address. Also, it
doesn't allow using a key index of zero if a pairwise key has
also been found.
This patch changes the key selection code to be (more) in line
with the 802.11 specification. I have confirmed that with this,
multicast frames are correctly decrypted and I've tested with
WEP as well.
While at it, I've cleaned up the semantics of the hardware flags
IEEE80211_HW_WEP_INCLUDE_IV and IEEE80211_HW_DEVICE_HIDES_WEP
and clarified them in the mac80211.h header; it is also now
allowed to set the IEEE80211_HW_DEVICE_HIDES_WEP option even if
it only applies to frames that have been decrypted by the hw,
unencrypted frames must be dropped but encrypted frames that
the hardware couldn't handle can be passed up unmodified.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 28 Aug 2007 21:01:53 +0000 (17:01 -0400)]
[MAC80211]: remove radar stuff
Unused in drivers, userspace and mac80211.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 28 Aug 2007 21:01:52 +0000 (17:01 -0400)]
[MAC80211]: ratelimit some RX messages
Many if not all of these messages can be triggered by sending
a few rogue frames which is trivially done and then we overflow
our logs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:52 +0000 (17:01 -0400)]
[MAC80211]: remove PRISM2_PARAM_RADIO_ENABLED
This now is unused in hostapd/wpa_supplicant.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:52 +0000 (17:01 -0400)]
[MAC80211]: remove IEEE80211_HW_HOST_GEN_BEACON flag
The flag is never checked because drivers can simply call
ieee80211_beacon_get() regardless of setting this flag.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:52 +0000 (17:01 -0400)]
[MAC80211]: remove reset callback
The callback isn't used so remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:52 +0000 (17:01 -0400)]
[MAC80211]: fix key debugfs
This fixes two issues with the key debugfs:
1) key index obviously isn't unique
2) various missing break statements led to bogus output
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Aug 2007 21:01:52 +0000 (17:01 -0400)]
[MAC80211]: avoid copying packets to interfaces that are down
David Woodhouse noticed that under some circumstances the number of slab
allocations kept growing. After looking a bit, this seemed to happen
when you had a management mode interface that was *down*.
The reason for this is that when the device is down, all management
frames get queued to the in-kernel MLME (via ieee80211_sta_rx_mgmt) but
then the sta work is invoked but doesn't run when the netif is down.
When you then bring the interface up, all such frames are freed, but if
you change the mode all of them are lost because the skb queue is
reinitialised as soon as you go back to managed mode. The skb queue is
correctly cleared when the interface is brought down, but the code
doesn't account for the fact that it may be filled while it is not up.
This patch should fix the issue by simply ignoring all interfaces that
are down when going through the RX handlers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Michael Wu <flamingice@sourmilk.net> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
This dongle does not follow the usb-irda specification, so it needs its own
special driver. First, it uses control URBs for data transfer, instead of
bulk or interrupt transfers; the only interrupt endpoint exposed seems to
be a dummy to prevent the interface from being rejected. Second, it uses
obfuscation and padding at the USB traffic level, for no apparent reason
other than to make reverse engineering harder (full details on obfuscation
in comments at beginning of source). Although it is advertised as a "4 Mbps
FIR dongle", it apparently loses packets at speeds greater than 57600 bps.
On plugin, this dongle reports vendor and device IDs: 0x07d0:0x4959 .
The Windows driver that is used normally to control this dongle has a
filename of KS-959.SYS .
Signed-off-by: Alex Villacís Lasso <a_villacis@palosanto.com> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This dongle does not follow the usb-irda specification, so it needs its own
special driver. Just like the Kingsun/Donshine dongle, it exposes two
interrupt endpoints. Reception is performed through direct reads from the
input endpoint. Transmission requires splitting the IrDA frames into 8-byte
segments, in which the first byte encodes how many of the remaining 7 bytes
are used as data. Speed change is made with a control URB just like the one
in cypress_m8, and it seems to support up to 115200 bps.
On plugin, this dongle reports vendor and device IDs: 0x07d0:0x4100
Signed-off-by: Alex Villacís Lasso <a_villacis@palosanto.com> Signed-off-by: Samuel Ortiz <samuel@sortiz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Tue, 28 Aug 2007 22:50:33 +0000 (15:50 -0700)]
[NET]: DIV_ROUND_UP cleanup (part two)
Hopefully captured all single statement cases under net/. I'm
not too sure if there is some policy about #includes that are
"guaranteed" (ie., in the current tree) to be available through
some other #included header, so I just added linux/kernel.h to
each changed file that didn't #include it previously.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 IPsec tunnel gateway incorrectly sends redirect to
sender if it is onlink host when network device the IPsec tunnelled
packet is arrived is the same as the one the decapsulated packet
is sent.
With this patch, it omits to send the redirect when the forwarding
skbuff carries secpath, since such skbuff should be assumed as
a decapsulated packet from IPsec tunnel by own.
Request for comments:
Alternatively we'd have another way to change net/ipv4/route.c
(__mkroute_input) to use RTCF_DOREDIRECT flag unless skbuff
has no secpath. It is better than this patch at performance
point of view because IPv4 redirect judgement is done at
routing slow-path. However, it should be taken care of resource
changes between SAD(XFRM states) and routing table. In other words,
When IPv4 SAD is changed does the related routing entry go to its
slow-path? If not, it is reasonable to apply this patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 IPsec tunnel gateway incorrectly sends redirect to
router or sender when network device the IPsec tunnelled packet
is arrived is the same as the one the decapsulated packet
is sent.
With this patch, it omits to send the redirect when the forwarding
skbuff carries secpath, since such skbuff should be assumed as
a decapsulated packet from IPsec tunnel by own.
It may be a rare case for an IPsec security gateway, however
it is not rare when the gateway is MIPv6 Home Agent since
the another tunnel end-point is Mobile Node and it changes
the attached network.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV6] XFRM: Fix connected socket to use transformation.
When XFRM policy and state are ready after TCP connection is started,
the traffic should be transformed immediately, however it does not
on IPv6 TCP.
It depends on a dst cache replacement policy with connected socket.
It seems that the replacement is always done for IPv4, however, on
IPv6 case it is done only when routing cookie is changed.
This patch fix that non-transformation dst can be changed to
transformation one.
This behavior is required by MIPv6 and improves IPv6 IPsec.
Fixes by Masahide NAKAMURA.
Signed-off-by: Noriaki TAKAMIYA <takamiya@po.ntts.co.jp> Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Sat, 25 Aug 2007 05:55:52 +0000 (22:55 -0700)]
[TCP] MIB: Add counters for discarded SACK blocks
In DSACK case, some events are not extraordinary, such as packet
duplication generated DSACK. They can arrive easily below
snd_una when undo_marker is not set (TCP being in CA_Open),
counting such DSACKs amoung SACK discards will likely just
mislead if they occur in some scenario when there are other
problems as well. Similarly, excessively delayed packets could
cause "normal" DSACKs. Therefore, separate counters are
allocated for DSACK events.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Sat, 25 Aug 2007 05:54:44 +0000 (22:54 -0700)]
[TCP]: Discard fuzzy SACK blocks
SACK processing code has been a sort of russian roulette as no
validation of SACK blocks is previously attempted. Besides, it
is not very clear what all kinds of broken SACK blocks really
mean (e.g., one that has start and end sequence numbers
reversed). So now close the roulette once and for all.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of using DPRINTK macro in ATM and use pr_debug (in kernel.h).
Using the standard macro is cleaner and forces code to check for bad arguments
and formatting.
Fixes from Thomas Graf.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
The ethernet header management only needs to handle a fixed
size address (6 bytes). If the memcpy/memset are changed to
be passed a constant length, then compiler can optimize for
this case (and if it is smart eliminate string instructions).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Wed, 22 Aug 2007 20:59:04 +0000 (13:59 -0700)]
[XFRM] netlink: Establish an attribute policy
Adds a policy defining the minimal payload lengths for all the attributes
allowing for most attribute validation checks to be removed from in
the middle of the code path. Makes updates more consistent as many format
errors are recognised earlier, before any changes have been attempted.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Graf [Wed, 22 Aug 2007 20:58:18 +0000 (13:58 -0700)]
[XFRM] netlink: Use nlmsg_parse() to parse attributes
Uses nlmsg_parse() to parse the attributes. This actually changes
behaviour as unknown attributes (type > MAXTYPE) no longer cause
an error. Instead unknown attributes will be ignored henceforth
to keep older kernels compatible with more recent userspace tools.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
[DCCP]: Make ccid3_hc_tx_update_x get a timestamp if needed
The code was too complicated, if p > 0 in ccid3_hc_tx_no_feedback_timer the
timestamp was being obtained to be passed to ccid3_hc_tx_update_x, where only
if p > 0 the timestamp was needed, so just leave it to ccid3_hc_tx_update_x to
obtain the timestamp if needed.
This will help in the upcoming changesets where we'll convert t_ld to ktime_t.
We'll eventually try to reuse ktime_get_real() calls again.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Wed, 15 Aug 2007 23:07:44 +0000 (16:07 -0700)]
[SCTP]: Rewrite of sctp buffer management code
This patch introduces autotuning to the sctp buffer management code
similar to the TCP. The buffer space can be grown if the advertised
receive window still has room. This might happen if small message
sizes are used, which is common in telecom environmens.
New tunables are introduced that provide limits to buffer growth
and memory pressure is entered if to much buffer spaces is used.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Garzik [Wed, 15 Aug 2007 23:01:56 +0000 (16:01 -0700)]
[ETHTOOL]: Internal cleanup of ethtool_value-related handlers
Several get/set functions can be handled by a passing the ethtool_op
function pointer directly to a generic function. This permits deletion
of a fair bit of redundant code.
Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Satyam Sharma [Fri, 10 Aug 2007 22:35:05 +0000 (15:35 -0700)]
[NET] netconsole: Support dynamic reconfiguration using configfs
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
This patch introduces support for dynamic reconfiguration (adding, removing
and/or modifying parameters of netconsole targets at runtime) using a
userspace interface exported via configfs. Documentation is also updated
accordingly.
Issues and brief design overview:
(1) Kernel-initiated creation / destruction of kernel objects is not
possible with configfs -- the lifetimes of the "config items" is managed
exclusively from userspace. But netconsole must support boot/module
params too, and these are parsed in kernel and hence netpolls must be
setup from the kernel. Joel Becker suggested to separately manage the
lifetimes of the two kinds of netconsole_target objects -- those created
via configfs mkdir(2) from userspace and those specified from the
boot/module option string. This adds complexity and some redundancy here
and also means that boot/module param-created targets are not exposed
through the configfs namespace (and hence cannot be updated / destroyed
dynamically). However, this saves us from locking / refcounting
complexities that would need to be introduced in configfs to support
kernel-initiated item creation / destroy there.
(2) In configfs, item creation takes place in the call chain of the
mkdir(2) syscall in the driver subsystem. If we used an ioctl(2) to
create / destroy objects from userspace, the special userspace program is
able to fill out the structure to be passed into the ioctl and hence
specify attributes such as local interface that are required at the time
we set up the netpoll. For configfs, this information is not available at
the time of mkdir(2). So, we keep all newly-created targets (via
configfs) disabled by default. The user is expected to set various
attributes appropriately (including the local network interface if
required) and then write(2) "1" to the "enabled" attribute. Thus,
netpoll_setup() is then called on the set parameters in the context of
_this_ write(2) on the "enabled" attribute itself. This design enables
the user to reconfigure existing netconsole targets at runtime to be
attached to newly-come-up interfaces that may not have existed when
netconsole was loaded or when the targets were actually created. All this
effectively enables us to get rid of custom ioctls.
(3) Ultra-paranoid configfs attribute show() and store() operations, with
sanity and input range checking, using only safe string primitives, and
compliant with the recommendations in Documentation/filesystems/sysfs.txt.
(4) A new function netpoll_print_options() is created in the netpoll API,
that just prints out the configured parameters for a netpoll structure.
netpoll_parse_options() is modified to use that and it is also exported to
be used from netconsole.
Signed-off-by: Satyam Sharma <satyam@infradead.org> Acked-by: Keiichi Kii <k-keiichi@bx.jp.nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Satyam Sharma [Fri, 10 Aug 2007 22:33:40 +0000 (15:33 -0700)]
[NET] netconsole: Support multiple logging targets
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
This patch introduces support for multiple targets, independent of
CONFIG_NETCONSOLE_DYNAMIC -- this is useful even in the default case and
(including the infrastructure introduced in previous patches) doesn't really
add too many bytes to module text. All the complexity (and size) comes with
the dynamic reconfigurability / userspace interface patch, and so it's
plausible users may want to keep this enabled but that disabled (say to avoid
a dependency on CONFIG_CONFIGFS_FS too).
Also update documentation to mention the use of ";" separator to specify
multiple logging targets in the boot/module option string.
Brief overview:
We maintain a target_list (and corresponding lock). Get rid of the static
"default_target" and introduce allocation and release functions for our
netconsole_target objects (but keeping sure to preserve previous behaviour
such as default values). During init_netconsole(), ";" is used as the
separator to identify multiple target specifications in the boot/module option
string. The target specifications are parsed and netpolls setup. During
exit, the target_list is torn down and all items released.
Signed-off-by: Satyam Sharma <satyam@infradead.org> Signed-off-by: Keiichi Kii <k-keiichi@bx.jp.nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
To update fields of underlying netpoll structure at runtime on corresponding
NETDEV_CHANGEADDR or NETDEV_CHANGENAME notifications.
ioctl(SIOCSIFHWADDR or SIOCSIFNAME) could be used to change the hardware/MAC
address or name of the local interface that our netpoll is attached to.
Whenever this happens, netdev notifier chain is called out with the
NETDEV_CHANGEADDR or NETDEV_CHANGENAME event message. We respond to that and
update the local_mac or dev_name field of the struct netpoll. This makes
sense anyway, but is especially required for dynamic netconsole because the
netpoll structure's internal members become user visible files when either
sysfs or configfs are used. So this helps us to keep up with the MAC
address/name changes and keep values in struct netpoll uptodate.
[ Note that ioctl(SIOCSIFADDR) to change IP address of interface at
runtime is not handled (to update local_ip of netpoll) on purpose --
some setups may set the local_ip to a private address, not necessary
the actual IP address of the sender host, as presently allowed. ]
Signed-off-by: Satyam Sharma <satyam@infradead.org> Signed-off-by: Keiichi Kii <k-keiichi@bx.jp.nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Satyam Sharma [Fri, 10 Aug 2007 22:32:14 +0000 (15:32 -0700)]
[NET] netconsole: Introduce netconsole_target
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
Introduce a wrapper structure over netpoll to represent logging targets
configured in netconsole. This will get extended with other members in
further patches.
This is done independent of the (to-be-introduced) NETCONSOLE_DYNAMIC config
option so that we're able to drastically cut down on the #ifdef complexity of
final netconsole.c. Also, struct netconsole_target would be required for
multiple targets support also, and not just dynamic reconfigurability.
Signed-off-by: Satyam Sharma <satyam@infradead.org> Signed-off-by: Keiichi Kii <k-keiichi@bx.jp.nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Satyam Sharma [Fri, 10 Aug 2007 22:31:19 +0000 (15:31 -0700)]
[NET] netconsole: Add some useful tips to documentation
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
Add some useful general-purpose tips. Also suggest solution for the frequent
problem of console loglevel set too low numerically (i.e. for high priority
messages only) on the sender.
Signed-off-by: Satyam Sharma <satyam@infradead.org> Acked-by: Keiichi Kii <k-keiichi@bx.jp.nec.com> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Satyam Sharma [Fri, 10 Aug 2007 22:30:31 +0000 (15:30 -0700)]
[NET] netconsole: Use netif_running() in write_msg()
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
Avoid unnecessarily disabling interrupts and calling netpoll_send_udp() if the
corresponding local interface is not up.
Signed-off-by: Satyam Sharma <satyam@infradead.org> Acked-by: Keiichi Kii <k-keiichi@bx.jp.nec.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
Presently, boot/module parameters are set up quite differently for the case of
built-in netconsole (__setup() -> obsolete_checksetup() ->
netpoll_parse_options() -> strlen(config) == 0 in init_netconsole()) vs
modular netconsole (module_param_string() -> string copied to the config
variable -> strlen(config) != 0 init_netconsole() -> netpoll_parse_options()).
This patch makes both of them similar by doing exactly the equivalent of a
module_param_string() in option_setup() also -- just copying the param string
passed from the kernel command line into "config" variable. So,
strlen(config) != 0 in both cases, and netpoll_parse_options() is always
called from init_netconsole(), thus making the setup logic for both cases
similar.
Now, option_setup() is only ever called / used for the built-in case, so we
put it inside a #ifndef MODULE, otherwise gcc will complain about
option_setup() being "defined but not used". Also, the "configured" variable
is redundant with this patch and hence removed.
Signed-off-by: Satyam Sharma <satyam@infradead.org> Signed-off-by: Keiichi Kii <k-keiichi@bx.jp.nec.com> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Satyam Sharma [Fri, 10 Aug 2007 22:28:10 +0000 (15:28 -0700)]
[NET] netconsole: Remove bogus check
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
The (!np.dev) check in write_msg() is bogus (always false), because: np.dev is
set by netpoll_setup(), which is called by init_netconsole() before
register_console(), so write_msg() cannot be triggered unless netpoll_setup()
successfully set np.dev. Also np.dev cannot go away from under us, because
netpoll_setup() grabs us reference on it. So let's remove the bogus check.
Signed-off-by: Satyam Sharma <satyam@infradead.org> Acked-by: Keiichi Kii <k-keiichi@bx.jp.nec.com> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon initial work by Keiichi Kii <k-keiichi@bx.jp.nec.com>.
(1) Remove unwanted headers.
(2) Mark __init and __exit as appropriate.
(3) Various trivial codingstyle and prettification stuff.
Signed-off-by: Satyam Sharma <satyam@infradead.org> Signed-off-by: Keiichi Kii <k-keiichi@bx.jp.nec.com> Acked-by: Matt Mackall <mpm@selenic.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Fri, 10 Aug 2007 21:31:21 +0000 (14:31 -0700)]
[TCP]: Update comment about highest_sack validity
This stale info came from the original idea, which proved to be
unnecessarily complex, sacked_out > 0 is easy to do and that when
it's going to be needed anyway (it _can_ be valid also when
sacked_out == 0 but there's not going to be a guarantee about it
for now).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
Ilpo Järvinen [Thu, 9 Aug 2007 12:14:46 +0000 (15:14 +0300)]
[TCP]: Move sack_ok access to obviously named funcs & cleanup
Previously code had IsReno/IsFack defined as macros that were
local to tcp_input.c though sack_ok field has user elsewhere too
for the same purpose. This changes them to static inlines as
preferred according the current coding style and unifies the
access to sack_ok across multiple files. Magic bitops of sack_ok
for FACK and DSACK are also abstracted to functions with
appropriate names.
Note:
- One sack_ok = 1 remains but that's self explanary, i.e., it
enables sack
- Couple of !IsReno cases are changed to tcp_is_sack
- There were no users for IsDSack => I dropped it
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log