Linus Torvalds [Fri, 1 Aug 2008 18:22:45 +0000 (11:22 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
au1xmmc: raise segment size limit.
mmc_block: use proper sg iterators
mmc: properly iterate over sg list in debug check
mmc_test: Revert "mmc_test: test oversized sg lists"
sdhci: check correct return value
sdhci: disable DMA for req, not completely
sdhci: handle bug in JMB38x for sizes < 4 bytes
Linus Torvalds [Fri, 1 Aug 2008 17:55:07 +0000 (10:55 -0700)]
Merge git://git.infradead.org/battery-2.6
* git://git.infradead.org/battery-2.6:
power_supply: Sharp SL-6000 (tosa) batteries support
power_supply: fix up CHARGE_COUNTER output to be more precise
power_supply: add CHARGE_COUNTER property and olpc_battery support for it
power_supply: bump EC version check that we refuse to run with in olpc_battery
power_supply: cleanup of the OLPC battery driver
power_supply: add eeprom dump file to olpc_battery's sysfs
power_supply: Support serial number in olpc_battery
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (28 commits)
mm/hugetlb.c must #include <asm/io.h>
video: Fix up hp6xx driver build regressions.
sh: defconfig updates.
sh: Kill off stray mach-rsk7203 reference.
serial: sh-sci: Fix up SH7760/SH7780/SH7785 early printk regression.
sh: Move out individual boards without mach groups.
sh: Make sure AT_SYSINFO_EHDR is exposed to userspace in asm/auxvec.h.
sh: Allow SH-3 and SH-5 to use common headers.
sh: Provide common CPU headers, prune the SH-2 and SH-2A directories.
sh/maple: clean maple bus code
sh: More header path fixups for mach dir refactoring.
sh: Move out the solution engine headers to arch/sh/include/mach-se/
sh: I2C fix for AP325RXA and Migo-R
sh: Shuffle the board directories in to mach groups.
sh: dma-sh: Fix up dreamcast dma.h mach path.
sh: Switch KBUILD_DEFCONFIG to shx3_defconfig.
sh: Add ARCH_DEFCONFIG entries for sh and sh64.
sh: Fix compile error of Solution Engine
sh: Proper __put_user_asm() size mismatch fix.
sh: Stub in a dummy ENTRY_OFFSET for uImage offset calculation.
...
Linus Torvalds [Fri, 1 Aug 2008 17:27:10 +0000 (10:27 -0700)]
Merge branch 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] qeth: avoid use of include/asm-s390
[S390] dont use kthread for smp_rescan_cpus().
[S390] virtio console: fix section mismatch warning.
[S390] cio: Include linux/string.h in schid.h.
[S390] qdio: fix section mismatch bug.
[S390] stp: fix section mismatch warning.
[S390] Remove diag 0x260 call from memory detection.
[S390] qdio: make sure qdr is aligned to page size
[S390] Add support for memory hot-remove.
[S390] Wire up new syscalls.
[S390] cio: Memory allocation for idset changed.
[S390] qeth: preallocated qeth header for hiper socket
[S390] Optimize storage key operations for anon pages
[S390] nohz/sclp: disable timer on synchronous waits.
[S390] ipl: Reboot from alternate device does not work when booting from file
[S390] dasd: Add support for enhanced VM UID
[S390] Remove last P390 trace.
Pierre Ossman [Mon, 28 Jul 2008 23:05:22 +0000 (01:05 +0200)]
mmc_test: Revert "mmc_test: test oversized sg lists"
This reverts commit 48b5352ea1891455eb8e824cf7d92f66931a090f. Oversized
sg lists are not allowed anymore, and the core even checks for them in
debug mode, so this test is entirely incorrect.
Heiko Carstens [Fri, 1 Aug 2008 14:39:23 +0000 (16:39 +0200)]
[S390] dont use kthread for smp_rescan_cpus().
Since git commit 3da1c84c00c7e5fa8348336bd8c342f9128b0f14
"workqueues: make get_online_cpus() useable for work->func()"
it is safe to call get_online_cpus() from workqueue context.
So remove the kthread workaround again.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
WARNING: vmlinux.o(.text+0x2e1cc4): Section mismatch in reference from the function s390_virtio_console_init() to the function .init.text:early_put_chars()
The function s390_virtio_console_init() references
the function __init early_put_chars().
This is often because s390_virtio_console_init lacks a __init
annotation or the annotation of early_put_chars is wrong.
WARNING: vmlinux.o(.text+0x2e1cd0): Section mismatch in reference from the function s390_virtio_console_init() to the function .init.text:virtio_cons_early_init()
The function s390_virtio_console_init() references
the function __init virtio_cons_early_init().
This is often because s390_virtio_console_init lacks a __init
annotation or the annotation of virtio_cons_early_init is wrong.
Cc: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Fri, 1 Aug 2008 14:39:20 +0000 (16:39 +0200)]
[S390] qdio: fix section mismatch bug.
Fix the two section mismatch warnings below.
This fixes two real bugs since the code which has __exit annotations
may already be gone when it is called.
WARNING: vmlinux.o(.init.text+0x1cc4a): Section mismatch in reference from the function init_QDIO() to the function .exit.text:qdio_setup_exit()
The function __init init_QDIO() references
a function __exit qdio_setup_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
qdio_setup_exit() so it may be used outside an exit section.
WARNING: vmlinux.o(.init.text+0x1cc7a): Section mismatch in reference from the function init_QDIO() to the function .exit.text:qdio_remove_perf_stats()
The function __init init_QDIO() references
a function __exit qdio_remove_perf_stats().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
qdio_remove_perf_stats() so it may be used outside an exit section.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Fri, 1 Aug 2008 14:39:19 +0000 (16:39 +0200)]
[S390] stp: fix section mismatch warning.
Fix these two (false positive) warnings by adding an __init annoation:
WARNING: vmlinux.o(.text+0x7e6a): Section mismatch in reference from the function stp_reset() to the function .init.text:__alloc_bootmem()
The function stp_reset() references
the function __init __alloc_bootmem().
This is often because stp_reset lacks a __init
annotation or the annotation of __alloc_bootmem is wrong.
WARNING: vmlinux.o(.text+0x7ece): Section mismatch in reference from the function stp_reset() to the function .init.text:free_bootmem()
The function stp_reset() references
the function __init free_bootmem().
This is often because stp_reset lacks a __init
annotation or the annotation of free_bootmem is wrong.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Frank Blaschka [Fri, 1 Aug 2008 14:39:13 +0000 (16:39 +0200)]
[S390] qeth: preallocated qeth header for hiper socket
For hiper socket devices this patch will economize the reallocation
of the tx skb data segment by allocating separate memory for the qdio
transport information (qeth header).
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[S390] Optimize storage key operations for anon pages
For anonymous pages without a swap cache backing the check in
page_remove_rmap for the physical dirty bit in page_remove_rmap is
unnecessary. The instructions that are used to check and reset the dirty
bit are expensive. Removing the check noticably speeds up process exit.
In addition the clearing of the dirty bit in __SetPageUptodate is
pointless as well. With these two changes there is no storage key
operation for an anonymous page anymore if it does not hit the swap
space.
The micro benchmark which repeatedly executes an empty shell script
gets about 5% faster.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Fri, 1 Aug 2008 14:39:11 +0000 (16:39 +0200)]
[S390] nohz/sclp: disable timer on synchronous waits.
sclp_sync_wait wait synchronously for an sclp interrupt and disables
timer interrupts. However on the irq enter paths there is an extra
check if a timer interrupt would be due and calls the timer callback.
This would schedule softirqs in the wrong context.
So introduce local_tick_enable/disable which prevents this.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Fri, 1 Aug 2008 14:39:10 +0000 (16:39 +0200)]
[S390] ipl: Reboot from alternate device does not work when booting from file
During startup we check if diag308 works using diag 308 subcode 6,
which stores the actual ipl information. This fails with rc = 0x102, if
the system has been ipled from the HMC using load from CD or load from file.
In the case of rc = 0x102 we have to assume that diag 308 is working,
since it still can be used to ipl from an alternative device.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When z/VM provides two virtual devices (minidisks) that reside on the
same real device, both will receive the configuration data from the
real device and thus get the same uid. To fix this problem, z/VM
provides an additional configuration data record that allows to
distinguish between minidisks.
z/VM APAR VM64273 needs be installed so this fix has an effect.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The iov_iter_advance() function would look at the iov->iov_len entry
even though it might have iterated over the whole array, and iov was
pointing past the end. This would cause DEBUG_PAGEALLOC to trigger a
kernel page fault if the allocation was at the end of a page, and the
next page was unallocated.
The quick fix is to just change the order of the tests: check that there
is any iovec data left before we check the iov entry itself.
Thanks to Alexey Dobriyan for finding this case, and testing the fix.
Reported-and-tested-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
romfs_readpage: don't report errors for pages beyond i_size
We zero-fill them like we are supposed to, and that's all fine. It's
only an error if the 'romfs_copyfrom()' routine isn't able to fill the
data that is supposed to be there.
Most of the patch is really just re-organizing the code a bit, and using
separate variables for the error value and for how much of the page we
actually filled from the filesystem.
Reported-and-tested-by: Chris Fester <cfester@wms.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Matt Waddel <matt.waddel@freescale.com> Cc: Greg Ungerer <gerg@snapgear.com> Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
Jason Wessel [Tue, 29 Jul 2008 20:58:53 +0000 (15:58 -0500)]
[MIPS] kgdb: add arch support for the kernel's kgdb core
The new kgdb architecture specific handler registers and unregisters
dynamically for exceptions depending on when you configure a kgdb I/O
driver.
Aside from initializing the exceptions earlier in the boot process,
kgdb should have no impact on a device when it is compiled in so long
as an I/O module is not configured for use.
There have been quite a number of contributors during the existence of
this patch (see arch/mips/kernel/kgdb.c). Most recently Jason
re-wrote the mips kgdb logic to use the die notification handlers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Jason Wessel [Tue, 29 Jul 2008 20:58:52 +0000 (15:58 -0500)]
[MIPS] kgdb: Remove existing implementation
This patch explicitly removes the kgdb implementation, for mips which
is intended to be followed by a patch that adds a kgdb implementation
for MIPS that makes use of the kgdb core in the kernel.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Random cleanups spotted by checkpatch script.
* Do not initialize panic_timeout. "panic=" kernel parameter can be used.
* Do not add "ip=any" or "ip=bootp". This options is not board specific.
* Do not add "root=/dev/nfs". This is default on CONFIG_ROOT_NFS.
* Kill unused error checking.
* Fix IRQ comment to match current code.
* Kill some unneeded includes
* ST0_ERL is already cleared in generic code.
* conswitchp is initialized generic code.
* __init is not needed in prototype.
Adrian Bunk [Tue, 29 Jul 2008 06:46:34 +0000 (09:46 +0300)]
[MIPS] RB532: Flags are unsigned long
A recent generic change now catches such bugs:
<-- snip -->
...
CC arch/mips/rb532/time.o
cc1: warnings being treated as errors
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c: In function 'plat_time_init':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c:55: error: comparison of distinct pointer types lacks a cast
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c:66: error: comparison of distinct pointer types lacks a cast
make[2]: *** [arch/mips/rb532/time.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Kevin Hickey [Mon, 28 Jul 2008 18:09:26 +0000 (13:09 -0500)]
[MIPS] Initialization of Alchemy boards
An earlier update changed some calls from simple_strotl to strict_strtol but
did not account for the differences in the syntax between the calls.
simple_strotl returns the integer; strict_strtol returns an error code and
takes a pointer to the result. As it was, NULL was being passed in place of
the result, which led to failures during kernel initialization when using
YAMON.
Signed-off-by: Kevin Hickey <khickey@rmicorp.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Bug originally found and reported by Julia Lawall <julia@diku.dk>. I
decieded that the whole error check was mostly useless paranoia and should
be discarded. It would only ever trigger if r3k_have_wired_reg has a wrong
value.
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
net: Make "networking" one-click deselectable.
ipv6: Fix useless proc net sockstat6 removal
tcp: MD5: Use MIB counter instead of warning for MD5 mismatch.
pkt_sched: Fix OOPS on ingress qdisc add.
niu: Fix error checking in niu_ethflow_to_class.
IPv6: datagram_send_ctl() should exit immediately when an error occured
mac80211: fix mesh beaconing
PS3: gelic: use unsigned long for irqflags
mac80211: fix cfg80211 hooks for master interface
nl80211: fix dump callbacks
mac80211: partially fix skb->cb use
rtl8187: Improve wireless statistics for RTL8187B
rtl8187: Fix for TX sequence number problem
mac80211: append CONFIG_ to MAC80211_VERBOSE_PS_DEBUG in net/mac80211/tx.c.
mac80211: fix sparse integer as NULL pointer warning
drivers/net/wireless/iwlwifi/iwl-led.c: printk fix
mac80211: return correct error return from ieee80211_wep_init
mac80211: tx, use dev_kfree_skb_any for beacon_get
rt2x00: Clear queue entry flags during initialization
rt2x00: Force full register config after start()
...
Dean Nelson [Wed, 30 Jul 2008 05:34:19 +0000 (22:34 -0700)]
sgi-xp: setup the notify GRU message queue
Setup the notify GRU message queue that is used for sending user messages
on UV systems.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:18 +0000 (22:34 -0700)]
sgi-xp: setup the activate GRU message queue
Setup the activate GRU message queue that is used for partition activation
and channel connection on UV systems.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:18 +0000 (22:34 -0700)]
sgi-xp: cleanup naming of partition defines
Cleanup naming of partition defines.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:17 +0000 (22:34 -0700)]
sgi-xp: move xpc_check_remote_hb() to support both SN2 and UV
Move xpc_check_remote_hb() so it can support both SN2 and UV.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:16 +0000 (22:34 -0700)]
sgi-xp: add usage of GRU driver by xpc_remote_memcpy()
Add UV support to xpc_remote_memcpy(), which involves interfacing to the
GRU driver.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:16 +0000 (22:34 -0700)]
sgi-xp: enable building of XPC/XPNET on x86_64
Get XPC/XPNET to build on x86_64. Trying to modprobe them up on a non-UV
or sn2 system will result in a -ENODEV.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:15 +0000 (22:34 -0700)]
sgi-xp: add 'jiffies' to reserved page's timestamp name
Rename XPC's reserved page's timestamp member to reflect the units of time
involved.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:14 +0000 (22:34 -0700)]
sgi-xp: use standard bitops macros and functions
Change sgi-xp to use the standard bitops macros and functions instead of
trying to invent its own mechanism.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:14 +0000 (22:34 -0700)]
sgi-xp: eliminate '>>>' in comments
Comments in /drivers/misc/sgi-xp has been using '>>>' as a means to draw
attention to something that needs to be done or considered. To avoid
colliding with git rejects, '>>>' will now be replaced by '!!!' to
indicate something to do, and by '???' to indicate something to be
considered.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:13 +0000 (22:34 -0700)]
sgi-xp: add _sn2 suffix to a few variables
Add an '_sn2' suffix to some variables found in xpc_sn2.c.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:13 +0000 (22:34 -0700)]
sgi-xp: isolate remote copy buffer to sn2 only
Make the remote copy buffer an sn2 only item.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:12 +0000 (22:34 -0700)]
sgi-xp: enable XPNET to handle more than 64 partitions
Enable XPNET to support more than 64 partitions.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:11 +0000 (22:34 -0700)]
sgi-xp: isolate allocation of XPC's msgqueues to sn2 only
Move the allocation of XPC's msgqueues to xpc_sn2.c.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:11 +0000 (22:34 -0700)]
sgi-xp: replace AMO_t typedef by struct amo
Replace the AMO_t typedef by a direct reference to 'struct amo'.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:10 +0000 (22:34 -0700)]
sgi-xp: separate chctl_flags from XPC's notify IRQ
Tie current IPI references to either XPC's notify IRQ or channel control
flags.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:09 +0000 (22:34 -0700)]
sgi-xp: isolate additional sn2 specific code
Move additional sn2 specific code into xpc_sn2.c.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:09 +0000 (22:34 -0700)]
sgi-xp: isolate activate IRQ's hardware specific components
Isolate architecture specific code related to XPC's activate IRQ.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:08 +0000 (22:34 -0700)]
sgi-xp: move xpc_allocate() into xpc_send()/xpc_send_notify()
Move xpc_allocate() functionality into xpc_send()/xpc_send_notify() so
xpc_allocate() no longer needs to be called by XPNET.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:07 +0000 (22:34 -0700)]
sgi-xp: base xpc_rsvd_page's timestamp on jiffies
Change XPC's reserved page timestamp to be based on jiffies.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:07 +0000 (22:34 -0700)]
sgi-xp: isolate xpc_vars structure to sn2 only
Isolate the xpc_vars structure of XPC's reserved page to sn2 only.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:06 +0000 (22:34 -0700)]
sgi-xp: isolate xpc_vars_part structure to sn2 only
Isolate the xpc_vars_part structure of XPC's reserved page to sn2 only.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:05 +0000 (22:34 -0700)]
sgi-xp: prepare xpc_rsvd_page to work on either sn2 or uv hardware
Prepare XPC's reserved page header to work for either sn2 or uv.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:05 +0000 (22:34 -0700)]
sgi-xp: create a common xp_remote_memcpy() function
Create a common remote memcpy function that maps to what the hardware
booted supports.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:04 +0000 (22:34 -0700)]
sgi-xp: support runtime selection of xp_max_npartitions
Support runtime selection of the max number of partitions based on the
hardware being run on.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:03 +0000 (22:34 -0700)]
sgi-xp: define BYTES_PER_WORD
Add a BYTES_PER_WORD #define.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:03 +0000 (22:34 -0700)]
sgi-xp: define xpSalError reason code
Define xpSalError reason code.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:02 +0000 (22:34 -0700)]
sgi-xp: define is_shub() and is_uv() macros
Define the is_shub()/is_uv() macros if they've not already been defined.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jack Steiner [Wed, 30 Jul 2008 05:34:02 +0000 (22:34 -0700)]
GRU Driver V3: fixes to resolve code review comments
Fixes problems identified in a code review:
- add comment with high level dscription of the GRU
- prepend "gru_" to all global names
- delete unused function
- couple of trivial bug fixes
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Jack Steiner <steiner@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jack Steiner [Wed, 30 Jul 2008 05:33:58 +0000 (22:33 -0700)]
GRU Driver: resource management
This file contains functions realted to managing GRU resources provided to
the user. Examples include GRU context assignment, load, unload,
migration, etc..
Signed-off-by: Jack Steiner <steiner@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jack Steiner [Wed, 30 Jul 2008 05:33:54 +0000 (22:33 -0700)]
GRU Driver: hardware data structures
This series of patches adds a driver for the SGI UV GRU. The driver is
still in development but it currently compiles for both x86_64 & IA64.
All simple regression tests pass on IA64. Although features remain to be
added, I'd like to start the process of getting the driver into the
kernel. Additional kernel drivers will depend on services provide by the
GRU driver.
The GRU is a hardware resource located in the system chipset. The GRU
contains memory that is mmaped into the user address space. This memory
is used to communicate with the GRU to perform functions such as
load/store, scatter/gather, bcopy, AMOs, etc. The GRU is directly
accessed by user instructions using user virtual addresses. GRU
instructions (ex., bcopy) use user virtual addresses for operands.
The GRU contains a large TLB that is functionally very similar to
processor TLBs. Because the external contains a TLB with user virtual
address, it requires callouts from the core VM system when certain types
of changes are made to the process page tables. There are several MMUOPS
patches currently being discussed but none has been accepted into the
kernel. The GRU driver is built using version V18 from Andrea Arcangeli.
This patch:
Contains the definitions of the hardware GRU data structures that are used
by the driver to manage the GRU.
[akpm@linux-foundation;org: export hpage_shift] Signed-off-by: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jack Steiner [Wed, 30 Jul 2008 05:33:53 +0000 (22:33 -0700)]
mm: add zap_vma_ptes(): a library function to unmap driver ptes
zap_vma_ptes() is intended to be used by drivers to unmap ptes assigned to the
driver private vmas. This interface is similar to zap_page_range() but is
less general & less likely to be abused.
Needed by the GRU driver.
Signed-off-by: Jack Steiner <steiner@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6 / log