NeilBrown [Tue, 15 Nov 2005 08:09:12 +0000 (00:09 -0800)]
[PATCH] md: make md threads interruptible again
Despite the fact that md threads don't need to be signalled, and won't
respond to signals anyway, we need to have an 'interruptible' wait, else
they stay in 'D' state and add to the load average.
(akpm: the signal_pending() test is unneeded - we'll fix that up in the next
round. For now, leave it there because that's how the code used to be).
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Tue, 15 Nov 2005 08:09:11 +0000 (00:09 -0800)]
[PATCH] md: mark START_ARRAY deprecated with a date
This was marked deprecated "after 2.6" back in the 2.5 days. But now it
seems there isn't going to be any "after 2.6", and we deprecate by date
now. So set a date.
Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Tue, 15 Nov 2005 08:09:10 +0000 (00:09 -0800)]
[PATCH] knfsd: make sure nfsd doesn't hog a cpu forever
Being kernel-threads, nfsd servers don't get pre-empted (depending on
CONFIG). If there is a steady stream of NFS requests that can be served
from cache, an nfsd thread may hold on to a cpu indefinitely, which isn't
very friendly.
So it is good to have a cond_resched in there (just before looking for a
new request to serve), to make sure we play nice.
Signed-off-by: Neil Brown <neilb@suse.de> Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Corey Minyard [Tue, 15 Nov 2005 08:09:07 +0000 (00:09 -0800)]
[PATCH] ipmi: bump-driver-version
Lots of good changes to the driver lately that userspace will care about
the version of the driver. Bump the version from 36.0 to 38.0 to be higher
than 37 that the 2.4 driver came out with a few weeks ago which doesn't
have all the same changes.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com> Signed-off-by: Corey Minyard <minyard@acm.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Along with above patch, another patch was posted and has been merged
(3d1675b41b02d64bd1185903ea0d25a8c0bb6dea). That patch was dependent on
the above patch and now it should also be reverted.
Cc: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jochen Friedrich [Tue, 15 Nov 2005 05:58:18 +0000 (21:58 -0800)]
[LLC]: Fix typo
Signed-off-by: Jochen Friedrich <jochen@scram.de> Acked-by: Arnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jochen Friedrich [Tue, 15 Nov 2005 05:57:46 +0000 (21:57 -0800)]
[LLC]: Make core block on remote busy.
Signed-off-by: Jochen Friedrich <jochen@scram.de> Acked-by: Arnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Jochen Friedrich [Tue, 15 Nov 2005 05:57:15 +0000 (21:57 -0800)]
[LLC]: Fix TX window scaling
Signed-off-by: Jochen Friedrich <jochen@scram.de> Acked-by: Arnaldo Carvalho de Melo <acme@mandriva.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Andi Kleen [Sat, 5 Nov 2005 16:25:54 +0000 (17:25 +0100)]
[PATCH] x86_64: Remove CONFIG_CHECKING and add command line option for pagefault tracing
CONFIG_CHECKING covered some debugging code used in the early times
of the port. But it wasn't even SMP safe for quite some time
and the bugs it checked for seem to be gone.
This patch removes all the code to verify GS at kernel entry. There
haven't been any new bugs in this area for a long time.
Previously it also covered the sysctl for the page fault tracing.
That didn't make much sense because that code was unconditionally
compiled in. I made that a boot option now because it is typically
only useful at boot.
Magnus Damm [Sat, 5 Nov 2005 16:25:54 +0000 (17:25 +0100)]
[PATCH] x86_64: Make node boundaries consistent
The current x86_64 NUMA memory code is inconsequent when it comes to node
memory ranges. The exact behaviour varies depending on which config option
that is used.
setup_node_bootmem() has start and end as arguments and these are used to
calculate the size of the node like this: (end - start). This is all fine
if end is pointing to the first non-available byte. The problem is that the
current x86_64 code sometimes treats it as the last present byte and sometimes
as the first non-available byte. The result is that some configurations might
lose a page at the end of the range.
This patch tries to fix CONFIG_ACPI_NUMA, CONFIG_K8_NUMA and CONFIG_NUMA_EMU
so they all treat the end variable as the first non-available byte. This is
the same way as the single node code.
The patch is boot tested on dual x86_64 hardware with the above configurations,
but maybe the removed code is needed as some workaround?
Andi Kleen [Sat, 5 Nov 2005 16:25:54 +0000 (17:25 +0100)]
[PATCH] x86_64: Log machine checks from boot on Intel systems
The logging for boot errors was turned off because it was broken
on some AMD systems. But give Intel EM64T systems a chance because they are
supposed to be correct there.
The advantage is that there is a chance to actually log uncorrected
machine checks after the reset.
[PATCH] x86_64: Make ACPI NUMA and NUMA emulation peers of K8_NUMA in Kconfig
On x86_64 arches, there is no way to choose ACPI_NUMA without having to choose
K8_NUMA. CONFIG_K8_NUMA is not needed for Intel EM64T NUMA boxes. It also
looks odd if you have to select ACPI_NUMA from the power management menu.
This patch fixes those oddities. Patch does the following:
1. Makes NUMA a config option like other arches
2. Makes topology detection options like K8_NUMA dependent on NUMA
3. Choosing ACPI NUMA detection can be done from the standard
"Processor type and features" menu
AK: I fixed up the dependencies and changed the help texts a bit
on top of Kiran's patch.
Keeping this function does not makes sense because it's a copied (and
buggy) copy of sys_time. The only difference is that now.tv_sec (which is
a time_t, i.e. a 64-bit long) is copied (and truncated) into a int
(32-bit).
The prototype is the same (they both take a long __user *), so let's drop
this and redirect it to sys_time (and make sure it exists by defining
__ARCH_WANT_SYS_TIME).
Only disadvantage is that the sys_stime definition is also compiled (may be
fixed if needed by adding a separate __ARCH_WANT_SYS_STIME macro, and
defining it for all arch's defining __ARCH_WANT_SYS_TIME except x86_64).
[PATCH] x86_64: Set ____cacheline_maxaligned_in_smp alignment to 128 bytes
The current value was correct before the introduction of Intel EM64T support -
but now L1_CACHE_SHIFT_MAX can be less than L1_CACHE_SHIFT, which _is_ funny!
Between the few users of ____cacheline_maxaligned_in_smp, we also have (for
example) rcu_ctrlblk, and struct zone, with zone->{lru_,}lock. I.e. we have
a lot of excess cacheline bouncing on them.
No correctness issues, obviously. So this could even be merged for 2.6.14
(I'm not a fan of this idea, though).
Andi Kleen [Sat, 5 Nov 2005 16:25:54 +0000 (17:25 +0100)]
[PATCH] x86_64: Remove optimization for B stepping AMD K8
B stepping were the first shipping Opterons. memcpy/memset/copy_page/
clear_page had special optimized version for them. These are really
old and in the minority now and the difference to the generic versions
(using rep microcode) is not that big anyways. So just remove them.
TODO: figure out optimized versions for Intel Netburst based EM64T
[PATCH] x86-64/i386: Intel HT, Multi core detection fixes
Fields obtained through cpuid vector 0x1(ebx[16:23]) and
vector 0x4(eax[14:25], eax[26:31]) indicate the maximum values and might not
always be the same as what is available and what OS sees. So make sure
"siblings" and "cpu cores" values in /proc/cpuinfo reflect the values as seen
by OS instead of what cpuid instruction says. This will also fix the buggy BIOS
cases (for example where cpuid on a single core cpu says there are "2" siblings,
even when HT is disabled in the BIOS.
http://bugzilla.kernel.org/show_bug.cgi?id=4359)
Andi Kleen [Sat, 5 Nov 2005 16:25:54 +0000 (17:25 +0100)]
[PATCH] x86_64: Don't enable interrupt unconditionally in reboot path
When they were disabled before (e.g. after a panic) it's better
to keep them off, otherwise followon panics can happen from timer
interrupt handlers etc.
Drawback is that pageup in the console won't work anymore though.
Shaohua Li [Sat, 5 Nov 2005 16:25:54 +0000 (17:25 +0100)]
[PATCH] x86_64: Force correct address space size for MTRR on some 64bit Intel Xeons
They report 40bit, but only have 36bits of physical address space.
This caused problems with setting up the correct masks for MTRR.
CPUID workaround for steppings 0F33h(supporting x86) and 0F34h(supporting x86
and EM64T). Detail info can be found at:
http://download.intel.com/design/Xeon/specupdt/30240216.pdf
http://download.intel.com/design/Pentium4/specupdt/30235221.pdf
Eric Dumazet [Sat, 5 Nov 2005 16:25:54 +0000 (17:25 +0100)]
[PATCH] x86_64: Optimize NUMA node hash function
Compute the highest possible value for memnode_shift, in order to reduce
footprint of memnodemap[] to the minimum, thus making all users
(phys_to_nid(), kfree()), more cache friendly.
Andi Kleen [Sat, 5 Nov 2005 16:25:54 +0000 (17:25 +0100)]
[PATCH] x86_64: New heuristics to find out hotpluggable CPUs.
With a NR_CPUS==128 kernel with CPU hotplug enabled we would waste 4MB
on per CPU data of all possible CPUs. The reason was that HOTPLUG
always set up possible map to NR_CPUS cpus and then we need to allocate
that much (each per CPU data is roughly ~32k now)
The underlying problem is that ACPI didn't tell us how many hotplug CPUs
the platform supports. So the old code just assumed all, which would
lead to this memory wastage.
This implements some new heuristics:
- If the BIOS specified disabled CPUs in the ACPI/mptables assume they
can be enabled later (this is bending the ACPI specification a bit,
but seems like a obvious extension)
- The user can overwrite it with a new additionals_cpus=NUM option
- Otherwise use half of the available CPUs or 2, whatever is more.
Andi Kleen [Sat, 5 Nov 2005 16:25:53 +0000 (17:25 +0100)]
[PATCH] x86_64: Only use asm/sections.h to declare section symbols
Adding __initdata_* to asm-generic/sections.h
Replaces a lot of open coded externs in arch/x86_64/*
I had to change __bss_end to __bss_stop to match the other architectures.
We should zap the low mappings, as soon as possible, so that we can catch
kernel bugs more effectively. Previously early boot had NULL mapped
and didn't trap on NULL references.
This patch introduces boot_level4_pgt, which will always have low identity
addresses mapped. Druing boot, all the processors will use this as their
level4 pgt. On BP, we will switch to init_level4_pgt as soon as we enter C
code and zap the low mappings as soon as we are done with the usage of
identity low mapped addresses. On AP's we will zap the low mappings as
soon as we jump to C code.
Andi Kleen [Sat, 5 Nov 2005 16:25:53 +0000 (17:25 +0100)]
[PATCH] x86_64: Fix gcc 4 warning in aperture.c
Fix
arch/x86_64/kernel/aperture.c: In function #iommu_hole_init#:
arch/x86_64/kernel/aperture.c:199: warning: #aper_order# may be used uninitialized in this function
James Cleverdon [Sat, 5 Nov 2005 16:25:53 +0000 (17:25 +0100)]
[PATCH] i386/x86-64: Share interrupt vectors when there is a large number of interrupt sources
Here's a patch that builds on Natalie Protasevich's IRQ compression
patch and tries to work for MPS boots as well as ACPI. It is meant for
a 4-node IBM x460 NUMA box, which was dying because it had interrupt
pins with GSI numbers > NR_IRQS and thus overflowed irq_desc.
The problem is that this system has 270 GSIs (which are 1:1 mapped with
I/O APIC RTEs) and an 8-node box would have 540. This is much bigger
than NR_IRQS (224 for both i386 and x86_64). Also, there aren't enough
vectors to go around. There are about 190 usable vectors, not counting
the reserved ones and the unused vectors at 0x20 to 0x2F. So, my patch
attempts to compress the GSI range and share vectors by sharing IRQs.
Jacob Shin [Sat, 5 Nov 2005 16:25:53 +0000 (17:25 +0100)]
[PATCH] x86_64: Support for AMD specific MCE Threshold.
MC4_MISC - DRAM Errors Threshold Register realized under AMD K8 Rev F.
This register is used to count correctable and uncorrectable ECC errors that occur during DRAM read operations.
The user may interface through sysfs files in order to change the threshold configuration.
bank%d/error_count - reads current error count, write to clear.
bank%d/interrupt_enable - set/clear interrupt enable.
bank%d/threshold_limit - read/write the threshold limit.
APIC vector 0xF9 in hw_irq.h.
5 software defined bank ids in mce.h.
new apic.c function to setup threshold apic lvt.
defaults to interrupt off, count enabled, and threshold limit max.
sysfs interface created on /sys/devices/system/threshold.
Andi Kleen [Sat, 5 Nov 2005 16:25:53 +0000 (17:25 +0100)]
[PATCH] x86_64: Account mem_map in VM holes accounting
The VM needs to know about lost memory in zones to accurately
balance dirty pages. This patch accounts mem_map in there too,
which fixes a constant errror of a few percent. Also some
other misc mappings and the kernel text itself are accounted
too.
Andi Kleen [Sat, 5 Nov 2005 16:25:53 +0000 (17:25 +0100)]
[PATCH] x86_64: Add 4GB DMA32 zone
Add a new 4GB GFP_DMA32 zone between the GFP_DMA and GFP_NORMAL zones.
As a bit of historical background: when the x86-64 port
was originally designed we had some discussion if we should
use a 16MB DMA zone like i386 or a 4GB DMA zone like IA64 or
both. Both was ruled out at this point because it was in early
2.4 when VM is still quite shakey and had bad troubles even
dealing with one DMA zone. We settled on the 16MB DMA zone mainly
because we worried about older soundcards and the floppy.
But this has always caused problems since then because
device drivers had trouble getting enough DMA able memory. These days
the VM works much better and the wide use of NUMA has proven
it can deal with many zones successfully.
So this patch adds both zones.
This helps drivers who need a lot of memory below 4GB because
their hardware is not accessing more (graphic drivers - proprietary
and free ones, video frame buffer drivers, sound drivers etc.).
Previously they could only use IOMMU+16MB GFP_DMA, which
was not enough memory.
Another common problem is that hardware who has full memory
addressing for >4GB misses it for some control structures in memory
(like transmit rings or other metadata). They tended to allocate memory
in the 16MB GFP_DMA or the IOMMU/swiotlb then using pci_alloc_consistent,
but that can tie up a lot of precious 16MB GFPDMA/IOMMU/swiotlb memory
(even on AMD systems the IOMMU tends to be quite small) especially if you have
many devices. With the new zone pci_alloc_consistent can just put
this stuff into memory below 4GB which works better.
One argument was still if the zone should be 4GB or 2GB. The main
motivation for 2GB would be an unnamed not so unpopular hardware
raid controller (mostly found in older machines from a particular four letter
company) who has a strange 2GB restriction in firmware. But
that one works ok with swiotlb/IOMMU anyways, so it doesn't really
need GFP_DMA32. I chose 4GB to be compatible with IA64 and because
it seems to be the most common restriction.
The new zone is so far added only for x86-64.
For other architectures who don't set up this
new zone nothing changes. Architectures can set a compatibility
define in Kconfig CONFIG_DMA_IS_DMA32 that will define GFP_DMA32
as GFP_DMA. Otherwise it's a nop because on 32bit architectures
it's normally not needed because GFP_NORMAL (=0) is DMA able
enough.
One problem is still that GFP_DMA means different things on different
architectures. e.g. some drivers used to have #ifdef ia64 use GFP_DMA
(trusting it to be 4GB) #elif __x86_64__ (use other hacks like
the swiotlb because 16MB is not enough) ... . This was quite
ugly and is now obsolete.
These should be now converted to use GFP_DMA32 unconditionally. I haven't done
this yet. Or best only use pci_alloc_consistent/dma_alloc_coherent
which will use GFP_DMA32 transparently.
Paul Mackerras [Mon, 14 Nov 2005 10:55:15 +0000 (21:55 +1100)]
powerpc: Fix clearing of the FPSCR when invoking a signal handler
As pointed out by Gary Byers, we were clearing the image of the FPSCR
(floating point status and control register) in the thread_struct before
copying it to the user stack when invoking a signal. Thus the task
would see its FPSCR getting cleared when it took a signal.
While fixing it I noticed that our swapcontext system call was also
clearing FPSCR. It shouldn't, so I fixed that too.
Yasuyuki Kozakai [Mon, 14 Nov 2005 23:28:45 +0000 (15:28 -0800)]
[NETFILTER] fix leak of fragment queue at unloading nf_conntrack_ipv6
This patch makes nf_conntrack_ipv6 free all IPv6 fragment queues at module
unloading time. Also introduce a BUG_ON if we ever again have leaks in
the memory accounting.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yasuyuki Kozakai [Mon, 14 Nov 2005 23:28:18 +0000 (15:28 -0800)]
[NETFILTER] nf_conntrack: fix possibility of infinite loop while evicting nf_ct_frag6_queue
This synchronizes nf_ct_reasm with ipv6 reassembly, and fixes a possibility
of an infinite loop if CPUs evict and create nf_ct_frag6_queue in parallel.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yasuyuki Kozakai [Mon, 14 Nov 2005 23:27:43 +0000 (15:27 -0800)]
[NETFILTER]: fix type of sysctl variables in nf_conntrack_ipv6
These variables should be unsigned. This fixes sysctl handler for
nf_ct_frag6_{low,high}_thresh.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yasuyuki Kozakai [Mon, 14 Nov 2005 23:26:58 +0000 (15:26 -0800)]
[NETFILTER]: cleanup IPv6 Netfilter Kconfig
This removes linux 2.4 configs in comments as TODO lists.
And this also move the entry of nf_conntrack to top like IPv4 Netfilter
Kconfig.
Based on original patch by Krzysztof Piotr Oledzki <ole@ans.pl>.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Staticaly linked nf_conntrack_ipv4 requires nf_conntrack. but currently
nf_conntrack is linked after it. This changes the order of ipv4 and netfilter
to fix this.
Signed-off-by: Krzysztof Oledzki <olenf@ans.pl> Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
This patch unconditionally requires CAP_NET_ADMIN for all nfnetlink
messages. It also removes the per-message cap_required field, since all
existing subsystems use CAP_NET_ADMIN for all their messages anyway.
Patrick McHardy owes me a beer if we ever need to re-introduce this.
Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
KOVACS Krisztian [Mon, 14 Nov 2005 23:23:01 +0000 (15:23 -0800)]
[NETFILTER] nf_conntrack: Add missing code to TCP conntrack module
Looks like the nf_conntrack TCP code was slightly mismerged: it does
not contain an else branch present in the IPv4 version. Let's add that
code and make the testsuite happy.
Signed-off-by: KOVACS Krisztian <hidden@balabit.hu> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER] ctnetlink: More thorough size checking of attributes
Add missing size checks. Thanks Patrick McHardy for the hint.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER] nfnetlink: skip size check if size not specified (== 0)
Skip sizecheck if the size of the attribute wasn't specified, ie. zero.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER] ctnetlink: use size_t to make gcc-4.x happy
Make gcc-4.x happy. Use size_t instead of int. Thanks to Patrick McHardy
for the hint.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Garzik [Mon, 14 Nov 2005 19:50:05 +0000 (14:50 -0500)]
[libata] REQUEST SENSE handling fixes
- Move ATAPI check-condition handling out of the timeout handler
- Use multi-qc-issue feature to issue REQUEST SENSE ATAPI PACKET
command upon receiving an ATAPI check-condition.
This cleans things up a lot, and eliminates a nasty recursion bug.
Jeff Garzik [Mon, 14 Nov 2005 19:14:16 +0000 (14:14 -0500)]
[libata] minor fixes, new helpers
- in ata_dev_identify(), don't assume that all devices are either
ATA or ATAPI. In the future, this code will see port multipliers
and other devices.
- make a debugging printk less verbose
- add new helper ata_qc_reinit()
- add new helper BPRINTK() and port flag ATA_FLAG_DEBUGMSG, for
fine-grained debugging use.
Jeff Garzik [Mon, 14 Nov 2005 19:06:26 +0000 (14:06 -0500)]
[libata] fix bugs in ATAPI padding DMA mapping code
The ATAPI pad-to-next-32bit-boundary code modifies the scatterlist's
length variable, sometimes to zero. x86-64 platform would oops if a
zero-length scatterlist entry was asked to be mapped. Work around this
by ensuring that we never DMA-map a zero length buffer or SG entry.
Jeff Garzik [Mon, 14 Nov 2005 18:56:37 +0000 (13:56 -0500)]
[libata ahci] error handling fixes
Needed to get ATAPI working.
- dump hardware error bits, if hardware signals an error
- only reset hardware during timeout if a command was active
- call ata_qc_complete() with a fine-grained error mask.
Needed so that atapi_qc_complete() can distinguish between
device errors and other errors.
Paul Mackerras [Mon, 14 Nov 2005 06:31:55 +0000 (17:31 +1100)]
powerpc: Mark PREP and embedded as broken for now
These machines don't have working ARCH=powerpc support yet, so make
them depend on BROKEN so people don't enable them inadvertently and
get compile errors.
[PATCH] powerpc: kill ppc64 rtc.c, use genrtc instead
This moves the rtas RTC callbacks to rtas-rtc.c in arch/powerpc/kernel,
and kills the rest of arch/ppc64/kernel/rtc.c which was just a duplicate
of the genrtc functionality. Also enable build of genrtc for
CONFIG_PPC64 (it just works are we already have the required callbacks)
and enable it in all defconfigs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes various errors in the new functions added in the vDSO's,
I've now verified all functions on both 32 and 64 bits vDSOs. It also
fix a sign extension bug getting the initial time of day at boot that
could cause the monotonic clock value to be completely on bogus for
64 bits applications (with either the vDSO or the syscall) on
powermacs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch uses a FORCE dependency on the arch/powerpc/include/asm
symlink so that it always gets rebuilt, thus avoiding all sort of funny
errors if the .config is changed between 32 and 64 bits.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Fri, 11 Nov 2005 13:06:05 +0000 (00:06 +1100)]
[PATCH] powerpc: Turn cpu_irq_down into kexec_cpu_down
We currently have a ppc_md member called cpu_irq_down, which disables IRQs
for the cpu in question. The only caller of cpu_irq_down is the kexec code.
On pSeries we need to do more than just teardown IRQs at kexec time, so rename
the ppc_md member to kexec_cpu_down and expand it. The pSeries code needs to
know, and other platforms might too, whether we're doing a crash shutdown (ie.
panicking) or a regular kexec, so add a flag for that.
The pSeries implementation of kexec_cpu_down does an unregister VPA call, which
tells the Hypervisor to stop writing stuff into our pacas. Without this we can
get weird memory corruption bugs when we kexec, caused by the Hypervisor
writing into the first kernel's pacas which happens to be somewhere interesting
in the second kernel's memory.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Fri, 11 Nov 2005 03:25:24 +0000 (14:25 +1100)]
[PATCH] powerpc: Merge page.h
Merge asm-ppc/page.h and asm-ppc64/page.h into asm-powerpc/page.h,
asm-powerpc/page_32.h and asm-powerpc/page_64.h
Built for PPC (common_defconfig), with ARCH=powerpc, mostly built with
ARCH=ppc (other things break the build). Built and booted on P5 LPAR
for PPC64 with ARCH=ppc/powerpc (pseries_defconfig). Mostly built for
iSeries powerpc.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>