[PATCH] driver core: Add the ability to bind drivers to devices from userspace
This adds a single file, "bind", to the sysfs directory of every driver
registered with the driver core. To bind a device to a driver, write
the bus id of the device you wish to bind to that specific driver to the
"bind" file (remember to not add a trailing \n). If that bus id matches
a device on that bus, and it does not currently have a driver bound to
it, the probe sequence will be initiated with that driver and device.
Note, this requires that the driver itself be willing and able to accept
that device (usually through a device id type table). This patch does
not make it possible to override the driver's id table.
[PATCH] driver core: Add the ability to unbind drivers to devices from userspace
This adds a single file, "unbind", to the sysfs directory of every
device that is currently bound to a driver. To unbind the driver from
the device, write anything to this file and they will be disconnected
from each other.
Hugh Dickins [Wed, 29 Jun 2005 14:15:40 +0000 (15:15 +0100)]
[PATCH] Fix get_request nastiness
get_request is now expected to be holding on to queue_lock, with interrupts
disabled, when it returns NULL; but one path forgot that, causing all kinds
of nastiness under swap load - badness backtraces, strange failures, BUGs.
Something reverted most of the arch/sparc/Kconfig changes, leaving
arch/sparc/ unconfigurable. This patch re-removes the parts made redundant
by drivers/Kconfig in addition to a mysterious, spurious second instance of
source "mm/Kconfig". cvs strikes again?
Signed-off-by: William Irwin <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- uv_ratio : allow a ratio of saturation between u and v. If you
have a ratio of 40 and a saturation of 100, usat will be 80 and
vstat 120. Useful to correct a bad color balance.
- full_luma_range : provide a better contrast in using the full
range 0-253 of values instead of 16-253.
- coring : to have a better black level.
- radio range is now defined on tuner-core.c. Cleaning up.
*tuner-core.c:
- some tuner_info msgs will be generated only if insmod opt
tuner_debug enabled.
- Implemented tuner-core support for VIDIO_S_TUNER to allow
changing mono/stereo mode
- Remove unneeded config options.
- I2C_CLIENT_MULTI option removed.
- support for Philips FMD12ME hybrid tuner
- allow to initialize with another tuner
- Move PHILIPS_FMD initialization code to set_type function,
* tda8290:
- Fix dumb error in tda8290 tunning.
- Radio tuner uses high-precision step instead of 62.5 KHz.
*tea5767.c:
- tuner_info msgs will be generated only if insmod tuner option
tuner_debug enabled.
- some cleanups for better reading.
- Radio tuner uses high-precision step instead of 62.5 KHz.
- Changing radio mode stereo/mono for tea5767 working.
*tuner-simple.c:
- TNF9533-D/IF UHF fixup.
- Radio tuners now uses high-precision step instead of 62.5 KHz.
*mt20xx.c:
- Radio tuner uses high-precision step instead of 62.5 KHz.
*tda9887.c:
- tab and blank spaces corrections.
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br> Signed-off-by: Gerd Knorr <kraxel@bytesex.org> Signed-off-by: Nickolay V Shmyrev <nshmyrev@yandex.ru> Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de> Signed-off-by: Michael Krufky <mkrufky@m1k.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alan Cox [Wed, 29 Jun 2005 03:45:18 +0000 (20:45 -0700)]
[PATCH] irqpoll
Anyone reporting a stuck IRQ should try these options. Its effectiveness
varies we've found in the Fedora case. Quite a few systems with misdescribed
IRQ routing just work when you use irqpoll. It also fixes up the VIA systems
although thats now fixed with the VIA quirk (which we could just make default
as its what Redmond OS does but Linus didn't like it historically).
A small number of systems have jammed IRQ sources or misdescribes that cause
an IRQ that we have no handler registered anywhere for. In those cases it
doesn't help.
Signed-off-by: Alan Cox <number6@the-village.bc.nu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently in ext3 block reservation code, the global filesystem reservation
tree lock (rsv_block) is hold during the process of searching for a space
to make a new reservation window, including while scaning the block bitmap
to verify if the avalible window has a free block. Holding the lock during
bitmap scan is unnecessary and could possibly cause scalability issue and
latency issues.
This patch tries to address this by dropping the lock before scan the
bitmap. Before that we need to reserve the open window in case someone
else is targetting at the same window. Question was should we reserve the
whole free reservable space or just the window size we need. Reserve the
whole free reservable space will possibly force other threads which
intended to do block allocation nearby move to another block group(cause
bad layout). In this patch, we just reserve the desired size before drop
the lock and scan the block bitmap. This patch fixed a ext3 reservation
latency issue seen on a cvs check out test. Patch is tested with many fsx,
tiobench, dbench and untar a kernel test.
Signed-Off-By: Mingming Cao <cmm@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 29 Jun 2005 03:45:15 +0000 (20:45 -0700)]
[PATCH] blk: light iocontext ops
get_io_context needlessly turned off interrupts and checked for racing io
context creations. Both of which aren't needed, because the io context can
only be created while in process context of the current process.
Also, split the function in 2. A light version, current_io_context does not
elevate the reference count specifically, but can be used when in process
context, because the process holds a reference itself.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Jens Axboe <axboe@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 29 Jun 2005 03:45:13 +0000 (20:45 -0700)]
[PATCH] blk: __make_request efficiency
In the case where the request is not able to be merged by the elevator, don't
retake the lock and retry the merge mechanism after allocating a new request.
Instead assume that the chance of a merge remains slim, and now that we've
done most of the work allocating a request we may as well just go with it.
Also be rid of the GFP_ATOMIC allocation: we've got working mempools for the
block layer now, so let's save atomic memory for things like networking.
Lastly, in get_request_wait, do an initial get_request call before going into
the waitqueue. This is reported to help efficiency.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Jens Axboe <axboe@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The return value of "match_int" is checked 27 out of 28 times
In lib/parser.c
142 /**
143 * match_int: - scan a decimal representation of an integer from a substring_t
144 * @s: substring_t to be scanned
145 * @result: resulting integer on success
146 *
147 * Description: Attempts to parse the &substring_t @s as a decimal integer. On
148 * success, sets @result to the integer represented by the string and returns 0.
149 * Returns either -ENOMEM or -EINVAL on failure.
150 */
151 int match_int(substring_t *s, int *result)
152 {
153 return match_number(s, result, 0);
154 }
GOTO Masanori [Wed, 29 Jun 2005 03:45:05 +0000 (20:45 -0700)]
[PATCH] headers: include linux/types.h for usb_ch9.h
This patch for usb_ch9.h includes linux/types.h instead of asm/types.h so that
__le16 and so on is explicitly defined. It also cleans up non standard //
comment.
GOTO Masanori [Wed, 29 Jun 2005 03:45:03 +0000 (20:45 -0700)]
[PATCH] headers: enable ppc64 ___arch__swab16 and ___arch__swab32
This patch cleans up asm-ppc64/byteorder.h to enable ___arch__swab16 and
___arch__swab32 which are marked TODO currently. It removes ___arch__swab64
because ppc64 does not have short instruction combinations for swab64, the
recent gcc generates enough smart code that is equivalent to hand assembled
code under my tests.
Signed-off-by: GOTO Masanori <gotom@debian.or.jp> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sébastien Dugu [Wed, 29 Jun 2005 03:44:59 +0000 (20:44 -0700)]
[PATCH] aio-retry-fix: fix aio retry work queueing
In the case of buffered AIO, in the aio retry path (aio_run_iocb), when the
retry method returns EIOCBRETRY the kicked iocb is added to the context run
list but is never queued onto the work queue. The request therefore is
never completed.
This patch fixes that by adding the appropriate call to aio_queue_work in
aio_run_aiocb so that subsequent retries will be handled by the aio worker
thread.
Signed-off-by: Sébastien Dugué <sebastien.dugue@bull.net> Acked-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Looks like it sneaked back with the NFS ACL merge..
Signed-off-by: Christoph Hellwig <hch@lst.de> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: Neil Brown <neilb@cse.unsw.edu.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Wed, 29 Jun 2005 03:44:54 +0000 (20:44 -0700)]
[PATCH] swabb.h warning fixes
In file included from drivers/media/dvb/ttpci/av7110_hw.c:38:
include/linux/byteorder/swabb.h:96: warning: type qualifiers ignored on function return type
include/linux/byteorder/swabb.h:110: warning: type qualifiers ignored on function return type
In file included from drivers/media/dvb/ttpci/av7110_v4l.c:36:
include/linux/byteorder/swabb.h:96: warning: type qualifiers ignored on function return type
include/linux/byteorder/swabb.h:110: warning: type qualifiers ignored on function return type
In file included from drivers/media/dvb/ttpci/av7110_av.c:37:
include/linux/byteorder/swabb.h:96: warning: type qualifiers ignored on function return type
include/linux/byteorder/swabb.h:110: warning: type qualifiers ignored on function return type
drivers/isdn/icn/icn.c:719:4: warning: #warning TODO test headroom or use skb->nb to flag ACK
In file included from drivers/media/dvb/ttpci/av7110_ca.c:39:
include/linux/byteorder/swabb.h:96: warning: type qualifiers ignored on function return type
include/linux/byteorder/swabb.h:110: warning: type qualifiers ignored on function return type
In file included from drivers/media/dvb/ttpci/av7110.c:41:
include/linux/byteorder/swabb.h:96: warning: type qualifiers ignored on function return type
include/linux/byteorder/swabb.h:110: warning: type qualifiers ignored on function return type
Does declaring a function to return a const value actually mean something to
gcc?
Dunno. Kill it and replace sone `__inline__'s with `inline' too.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Wed, 29 Jun 2005 03:44:53 +0000 (20:44 -0700)]
[PATCH] hisax warning fixes
drivers/isdn/hisax/hfc4s8s_l1.c:317: warning: type qualifiers ignored on function return type
drivers/isdn/hisax/hfc4s8s_l1.c:329: warning: type qualifiers ignored on function return type
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid race occurs when some process have open file descriptor for class
device attributes and already firmware allocated memory are freed. Don't
allow negative loading timeout.
Signed-off-by: Stanislaw W. Gruszka <stf_xl@wp.pl> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oleg Nesterov [Wed, 29 Jun 2005 03:44:47 +0000 (20:44 -0700)]
[PATCH] ITIMER_REAL: fix possible deadlock and race
As Steven Rostedt pointed out, there are 2 problems with ITIMER_REAL
timers.
1. do_setitimer() does not call del_timer_sync() in case
when the timer is not pending (it_real_value() returns 0).
This is wrong, the timer may still be running, and it can
rearm itself.
2. It calls del_timer_sync() with tsk->sighand->siglock held.
This is deadlockable, because timer's handler needs this
lock too.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru> Acked-by: Steven Rostedt <rostedt@goodmis.org> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patrick McHardy [Tue, 28 Jun 2005 23:04:44 +0000 (16:04 -0700)]
[NETFILTER]: Fix connection tracking bug in 2.6.12
In 2.6.12 we started dropping the conntrack reference when a packet
leaves the IP layer. This broke connection tracking on a bridge,
because bridge-netfilter defers calling some NF_IP_* hooks to the bridge
layer for locally generated packets going out a bridge, where the
conntrack reference is no longer available. This patch keeps the
reference in this case as a temporary solution, long term we will
remove the defered hook calling. No attempt is made to drop the
reference in the bridge-code when it is no longer needed, tc actions
could already have sent the packet anywhere.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Tue, 28 Jun 2005 22:58:50 +0000 (15:58 -0700)]
[NET]: Add missing include to linux/netdevice.h
linux/etherdevice.h can't be included standalone at the moment, which
is required in order to sort the header files in the recommended
alphabetic order. This patch fixes that and is needed to build spider_net.
Signed-off-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 28 Jun 2005 22:40:02 +0000 (15:40 -0700)]
[IPVS]: Close race conditions on ip_vs_conn_tab list modification
In an smp system, it is possible for an connection timer to expire, calling
ip_vs_conn_expire while the connection table is being flushed, before
ct_write_lock_bh is acquired.
Since the list iterator loop in ip_vs_con_flush releases and re-acquires the
spinlock (even though it doesn't re-enable softirqs), it is possible for the
expiration function to modify the connection list, while it is being traversed
in ip_vs_conn_flush.
The result is that the next pointer gets set to NULL, and subsequently
dereferenced, resulting in an oops.
Signed-off-by: Neil Horman <nhorman@redhat.com> Acked-by: JulianAnastasov Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 28 Jun 2005 22:25:31 +0000 (15:25 -0700)]
[NET]: Remove gratuitous use of skb->tail in network drivers.
Many drivers use skb->tail unnecessarily.
In these situations, the code roughly looks like:
dev = dev_alloc_skb(...);
[optional] skb_reserve(skb, ...);
... skb->tail ...
But even if the skb_reserve() happens, skb->data equals
skb->tail. So it doesn't make any sense to use anything
other than skb->data in these cases.
Another case was the s2io.c driver directly mucking with
the skb->data and skb->tail pointers. It really just wanted
to do an skb_reserve(), so that's what the code was changed
to do instead.
Another reason I'm making this change as it allows some SKB
cleanups I have planned simpler to merge. In those cleanups,
skb->head, skb->tail, and skb->end pointers are removed, and
replaced with skb->head_room and skb->tail_room integers.
Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Jeff Garzik <jgarzik@pobox.com>
Ingo Molnar [Tue, 28 Jun 2005 14:40:42 +0000 (16:40 +0200)]
[PATCH] Tweak idle thread setup semantics
This patch tweaks idle thread setup semantics a bit: instead of setting
NEED_RESCHED in init_idle(), we do an explicit schedule() before calling
into cpu_idle().
This patch, while having no negative side-effects, enables wider use of
cond_resched()s. (which might happen in the stock kernel too, but it's
particulary important for voluntary-preempt)
Currently we cap request allocations at q->nr_requests, but we allow a
batching io context to allocate up to 32 more (default setting). This
can flood the queue with request allocations, with only a few batching
processes. The real fix would be to limit the number of batchers, but
as that isn't currently tracked, I suggest we just cap the maximum
number of allocated requests to eg 50% over the limit.
This was observed in real life, users typically see this as vmstat bo
numbers going off the wall with seconds of no queueing afterwards.
Behaviour this bursty is not beneficial.
Vlad Yasevich [Tue, 28 Jun 2005 20:24:23 +0000 (13:24 -0700)]
[SCTP] Make init & delayed sack timeouts configurable by user.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Bizon [Tue, 28 Jun 2005 20:21:12 +0000 (13:21 -0700)]
[IPV4]: ipconfig.c: fix dhcp timeout behaviour
I think there is a small bug in ipconfig.c in case IPCONFIG_DHCP is set
and dhcp is used.
When a DHCPOFFER is received, ip address is kept until we get DHCPACK.
If no ack is received, ic_dynamic() returns negatively, but leaves the
offered ip address in ic_myaddr.
This makes the main loop in ip_auto_config() break and uses the maybe
incomplete configuration.
Not sure if it's the best way to do, but the following trivial patch
correct this.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Dietmar Eggemann [Tue, 28 Jun 2005 20:06:23 +0000 (13:06 -0700)]
[IPV4]: Snmpv2 Mib IP counter ipInAddrErrors support
I followed Thomas' proposal to see every martian destination as a case
where the ipInAddrErrors counter has to be incremented. There are
two advantages by doing so: (1) The relation between the ipInReceive
counter and all the other ipInXXX counters is more accurate in the
case the RTN_UNICAST code check fails and (2) it makes the code in
ip_route_input_slow easier.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Lindgren [Tue, 28 Jun 2005 20:01:16 +0000 (21:01 +0100)]
[PATCH] ARM: 2760/1: Add a warning on dynamic tick timekeeping on some platforms
Patch from Tony Lindgren
This patch was suggested by RMK, and adds a warning on the accuracy
of timekeeping when using dynamic tick on some platforms. Depending
on the timer implementation, dynamic tick may affect the accuracy of
timekeeping.
Currently at least OMAP is known to have accurate timekeeping with
dynamic tick.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Richard Purdie [Tue, 28 Jun 2005 20:01:03 +0000 (21:01 +0100)]
[PATCH] ARM: 2761/1: OProfile: Add call graphing support for arm
Patch from Richard Purdie
Add functions to generate backtraces of both kernel and user processes
which allows oprofile's call graphing functionality to be used on arm.
This requires unstripped binaries/libs which use a frame pointer.
Signed-off-by: Richard Purdie Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David S. Miller [Tue, 28 Jun 2005 19:39:40 +0000 (12:39 -0700)]
[EBTABLES]: Fix thinkos in ebt_log.c
When converting over the skb_header_pointer(), I converted parts of
this module incorrectly. Kill the 'u' union in ebt_log() and all the
bogus references to it.
Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH] PCI: use the MCFG table to properly access pci devices (x86-64)
Now that we have access to the whole MCFG table, let's properly use it
for all pci device accesses (as that's what it is there for, some boxes
don't put all the busses into one entry.)
If, for some reason, the table is incorrect, we fallback to the "old
style" of mmconfig accesses, namely, we just assume the first entry in
the table is the one for us, and blindly use it.
[PATCH] PCI: use the MCFG table to properly access pci devices (i386)
Now that we have access to the whole MCFG table, let's properly use it
for all pci device accesses (as that's what it is there for, some boxes
don't put all the busses into one entry.)
If, for some reason, the table is incorrect, we fallback to the "old
style" of mmconfig accesses, namely, we just assume the first entry in
the table is the one for us, and blindly use it.
[PATCH] PCI: add proper MCFG table parsing to ACPI core.
This patch is the first step in properly handling the MCFG PCI table.
It defines the structures properly, and saves off the table so that the
pci mmconfig code can access it. It moves the parsing of the table a
little later in the boot process, but still before the information is
needed.
Keith Moore [Thu, 2 Jun 2005 10:42:37 +0000 (12:42 +0200)]
[PATCH] cpqphp: fix oops during unload without probe
drivers/pci/hotplug/cpqphp_core.c calls cpqphp_event_start_thread()
in one_time_init(), which is called whenever the hardware is probed.
Unfortunately, cpqphp_event_stop_thread() is *always* called when
the module is unloaded. If the hardware is never probed, then
cpqphp_event_stop_thread() tries to manipulate a couple of
uninitialized mutexes.
Signed-off-by: Keith Moore <keithmo@exmsft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Andrew Morton [Tue, 7 Jun 2005 06:07:46 +0000 (23:07 -0700)]
[PATCH] PCI: fix up errors after dma bursting patch and CONFIG_PCI=n
With CONFIG_PCI=n:
In file included from include/linux/pci.h:917,
from lib/iomap.c:6:
include/asm/pci.h:104: warning: `enum pci_dma_burst_strategy' declared inside parameter list
include/asm/pci.h:104: warning: its scope is only this definition or declaration, which is probably not what you want.
include/asm/pci.h: In function `pci_dma_burst_advice':
include/asm/pci.h:106: dereferencing pointer to incomplete type
include/asm/pci.h:106: `PCI_DMA_BURST_INFINITY' undeclared (first use in this function)
include/asm/pci.h:106: (Each undeclared identifier is reported only once
include/asm/pci.h:106: for each function it appears in.)
make[1]: *** [lib/iomap.o] Error 1
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David S. Miller [Thu, 2 Jun 2005 19:55:50 +0000 (12:55 -0700)]
[PATCH] PCI: DMA bursting advice
After seeing, at best, "guesses" as to the following kind
of information in several drivers, I decided that we really
need a way for platforms to specifically give advice in this
area for what works best with their PCI controller implementation.
Basically, this new interface gives DMA bursting advice on
PCI. There are three forms of the advice:
1) Burst as much as possible, it is not necessary to end bursts
on some particular boundary for best performance.
2) Burst on some byte count multiple. A DMA burst to some multiple of
number of bytes may be done, but it is important to end the burst
on an exact multiple for best performance.
The best example of this I am aware of are the PPC64 PCI
controllers, where if you end a burst mid-cacheline then
chip has to refetch the data and the IOMMU translations
which hurts performance a lot.
3) Burst on a single byte count multiple. Bursts shall end
exactly on the next multiple boundary for best performance.
Sparc64 and Alpha's PCI controllers operate this way. They
disconnect any device which tries to burst across a cacheline
boundary.
Actually, newer sparc64 PCI controllers do not have this behavior.
That is why the "pdev" is passed into the interface, so I can
add code later to check which PCI controller the system is using
and give advice accordingly.
Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Michael Ellerman [Fri, 13 May 2005 07:44:10 +0000 (17:44 +1000)]
[PATCH] PCI: fix-pci-mmap-on-ppc-and-ppc64.patch
This is an updated version of Ben's fix-pci-mmap-on-ppc-and-ppc64.patch
which is in 2.6.12-rc4-mm1.
It fixes the patch to work on PPC iSeries, removes some debug printks
at Ben's request, and incorporates your
fix-pci-mmap-on-ppc-and-ppc64-fix.patch also.
Originally from Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch was discussed at length on linux-pci and so far, the last
iteration of it didn't raise any comment. It's effect is a nop on
architecture that don't define the new pci_resource_to_user() callback
anyway. It allows architecture like ppc who put weird things inside of
PCI resource structures to convert to some different value for user
visible ones. It also fixes mmap'ing of IO space on those archs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] ACPI based I/O APIC hot-plug: acpiphp support
This patch adds PCI based I/O xAPIC hot-add support to ACPIPHP
driver. When PCI root bridge is hot-added, all PCI based I/O xAPICs
under the root bridge are hot-added by this patch. Hot-remove support
is TBD.
[PATCH] ACPI based I/O APIC hot-plug: add interfaces
This patch adds the following new interfaces for I/O xAPIC
hotplug. The implementation of these interfaces depends on each
architecture.
o int acpi_register_ioapic(acpi_handle handle, u64 phys_addr,
u32 gsi_base);
This new interface is to add a new I/O xAPIC specified by
phys_addr and gsi_base pair. phys_addr is the physical address
to which the I/O xAPIC is mapped and gsi_base is global system
interrupt base of the I/O xAPIC. acpi_register_ioapic returns
0 on success, or negative value on error.
o int acpi_unregister_ioapic(acpi_handle handle, u32 gsi_base);
This new interface is to remove a I/O xAPIC specified by
gsi_base. acpi_unregister_ioapic returns 0 on success, or
negative value on error.
Rajesh Shah [Thu, 28 Apr 2005 07:25:57 +0000 (00:25 -0700)]
[PATCH] acpi hotplug: decouple slot power state changes from physical hotplug
Current acpiphp code does not distinguish between the physical presence and
power state of a device/slot. That is, if a device has to be disabled, it
also tries to physically ejects the device. This patch decouples power state
from physical presence. You can now echo to the corresponding sysfs power
control file to repeatedly enable and disable a device without having to
physically re-insert it.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:55 +0000 (00:25 -0700)]
[PATCH] acpi hotplug: fix slot power-down problem with acpiphp
Earlier I reported that Matthew's acpiphp rewrite had problem in powering down
slot on my i386 system. The following patch is needed to get the acpiphp
rewrite properly powering down the slot.
Signed-off-by: Dely Sy <dely.l.sy@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:54 +0000 (00:25 -0700)]
[PATCH] acpi hotplug: clean up notify handlers on acpiphp unload
A root bridge may not have directly attached hotpluggable slots under it.
Instead, it may have p2p bridges with slots under it. In this case, we need
to clean up the p2p bridges and slots properly too. Patch below applies on
top of the original patch, and fixes this problem. Without this, acpiphp
leaves behind notify handlers on module unload, and subsequent module load
attempts don't work properly too. Patch was tested on an ia64 Tiger4 box.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:53 +0000 (00:25 -0700)]
[PATCH] acpi hotplug: convert acpiphp to use generic resource code
This patch converts acpiphp to use the generic PCI resource assignment code.
It's quite large, but most of it is deleting the acpiphp_pci and acpiphp_res
files. It's tested on an hp Integrity rx8620 (which won't work without this
patch). Testers with other hardware welcomed.
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:53 +0000 (00:25 -0700)]
[PATCH] acpi bridge hotadd: Export the interface to get PCI id for an ACPI handle
Export an acpi interface to get PCI domain/bus/devfn information from the
corresponding namespace handle. Used by acpiphp code to transpate the device
handle of the hot-plugged root bridge to the corresponding pci location
information.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:52 +0000 (00:25 -0700)]
[PATCH] acpi bridge hotadd: Allow ACPI .add and .start operations to be done independently
Create new interfaces to recursively add an acpi namespace object to the acpi
device list, and recursively start the namespace object. This is needed for
ACPI based hotplug of a root bridge hierarchy where the add operation must be
performed first and the start operation must be performed separately after the
hot-plugged devices have been properly configured.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:51 +0000 (00:25 -0700)]
[PATCH] acpi bridge hotadd: Read bridge resources when fixing up the bus
Read bridge io/mem/pfmem ranges when fixing up the bus so that bus resources
are tracked. This is required to properly support pci end device and bridge
hotplug.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:50 +0000 (00:25 -0700)]
[PATCH] acpi bridge hotadd: Remove hot-plugged devices that could not be allocated resources
When hot-plugging an I/O hierarchy that contains many bridges and leaf
devices, it's possible that there are not enough resources to start all the
device present. If we fail to assign a resource, clear the corresponding
value in the pci_dev structure, so other code can take corrective action.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:49 +0000 (00:25 -0700)]
[PATCH] acpi bridge hotadd: Make the PCI remove routines safe for failed hot-plug
When a root bridge hierarchy is hot-plugged, resource requirements for the new
devices may be greater than what the root bridge is decoding. In this case,
we want to remove devices that did not get needed resources. These devices
have been scanned into bus specific lists but not yet added to the global
device list. Make sure the pci remove functions can handle this case.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:49 +0000 (00:25 -0700)]
[PATCH] acpi bridge hotadd: Link newly created pci child bus to its parent on creation
When a pci child bus is created, add it to the parent's children list
immediately rather than waiting till pci_bus_add_devices(). For hot-plug
bridges/devices, pci_bus_add_devices() may be called much later, after they
have been properly configured. In the meantime, this allows us to use the
normal pci bus search functions for the hot-plug bridges/buses.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:48 +0000 (00:25 -0700)]
[PATCH] acpi bridge hotadd: Take the PCI lock when modifying pci bus or device lists
With root bridge and pci bridge hot-plug, new buses and devices can be added
or removed at run time. Protect the pci bus and device lists with the pci
lock when doing so.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:47 +0000 (00:25 -0700)]
[PATCH] acpi bridge hotadd: Prevent duplicate bus numbers when scanning PCI bridge
When hot-plugging a root bridge, as we try to assign bus numbers we may find
that the hotplugged hieratchy has more PCI to PCI bridges (i.e. bus
requirements) than available. Make sure we don't step over an existing bus
when that happens.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:46 +0000 (00:25 -0700)]
[PATCH] acpi bridge hotadd: Make pcibios_fixup_bus() hot-plug safe
PCI scan code calls the arch specific pcibios_fixup_bus() each time it scans a
new bridge. For root bridge hot-plug, the bridge and it's attached devices
may not have been configured properly yet, so it's not safe to claim those
resources at this time.
This code goes away when we clean up the way pci resources are claimed (in
pci_enable_device()), so this is only a stopgap fix.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rajesh Shah [Thu, 28 Apr 2005 07:25:45 +0000 (00:25 -0700)]
[PATCH] acpi bridge hotadd: Fix pci_enable_device() for p2p bridges
When checking if a PCI to PCI bridge should be enabled to decode memory and/or
IO resources, we need to look at all device resources not just the first 6.
This is needed to allow PCI bridges to pass down memory and IO accesses to
child devices even when the bridge itself does not consume resources in its
PCI BARs.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-2.6 / log