This patch adds extra information to the mirror status output, so that
it can be determined which device(s) have failed. For each mirror device,
a character is printed indicating the most severe error encountered. The
characters are:
* A => Alive - No failures
* D => Dead - A write failure occurred leaving mirror out-of-sync
* S => Sync - A sychronization failure occurred, mirror out-of-sync
* R => Read - A read failure occurred, mirror data unaffected
This allows userspace to properly reconfigure the mirror set.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch gives the ability to respond-to/record device failures
that happen during read operations. It also adds the ability to
read from mirror devices that are not the primary if they are
in-sync.
There are essentially two read paths in mirroring; the direct path
and the queued path. When a read request is mapped, if the region
is 'in-sync' the direct path is taken; otherwise the queued path
is taken.
If the direct path is taken, we must record bio information so that
if the read fails we can retry it. We then discover the status of
a direct read through mirror_end_io. If the read has failed, we will
mark the device from which the read was attempted as failed (so we
don't try to read from it again), restore the bio and try again.
If the queued path is taken, we discover the results of the read
from 'read_callback'. If the device failed, we will mark the device
as failed and attempt the read again if there is another device
where this region is known to be 'in-sync'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds the ability to requeue write I/O to
core device-mapper when there is a log device failure.
If a write to the log produces and error, the pending writes are
put on the "failures" list. Since the log is marked as failed,
they will stay on the failures list until a suspend happens.
Suspends come in two phases, presuspend and postsuspend. We must
make sure that all the writes on the failures list are requeued
in the presuspend phase (a requirement of dm core). This means
that recovery must be complete (because writes may be delayed
behind it) and the failures list must be requeued before we
return from presuspend.
The mechanisms to ensure recovery is complete (or stopped) was
already in place, but needed to be moved from postsuspend to
presuspend. We rely on 'flush_workqueue' to ensure that the
mirror thread is complete and therefore, has requeued all writes
in the failures list.
Because we are using flush_workqueue, we must ensure that no
additional 'queue_work' calls will produce additional I/O
that we need to requeue (because once we return from
presuspend, we are unable to do anything about it). 'queue_work'
is called in response to the following functions:
- complete_resync_work = NA, recovery is stopped
- rh_dec (mirror_end_io) = NA, only calls 'queue_work' if it
is ready to recover the region
(recovery is stopped) or it needs
to clear the region in the log*
**this doesn't get called while
suspending**
- rh_recovery_end = NA, recovery is stopped
- rh_recovery_start = NA, recovery is stopped
- write_callback = 1) Writes w/o failures simply call
bio_endio -> mirror_end_io -> rh_dec
(see rh_dec above)
2) Writes with failures are put on
the failures list and queue_work is
called**
** write_callbacks don't happen
during suspend **
- do_failures = NA, 'queue_work' not called if suspending
- add_mirror (initialization) = NA, only done on mirror creation
- queue_bio = NA, 1) delayed I/O scheduled before flush_workqueue
is called. 2) No more I/Os are being issued.
3) Re-attempted READs can still be handled.
(Write completions are handled through rh_dec/
write_callback - mention above - and do not
use queue_bio.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adds the calls to 'fail_mirror' if an error occurs during
mirror recovery (aka resynchronization). 'fail_mirror' is responsible
for recording the type of error by mirror device and ensuring an event
gets raised for the purpose of notifying userspace.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch gives mirror the ability to handle device failures
during normal write operations.
The 'write_callback' function is called when a write completes.
If all the writes failed or succeeded, we report failure or
success respectively. If some of the writes failed, we call
fail_mirror; which increments the error count for the device, notes
the type of error encountered (DM_RAID1_WRITE_ERROR), and
selects a new primary (if necessary). Note that the primary
device can never change while the mirror is not in-sync (IOW,
while recovery is happening.) This means that the scenario
where a failed write changes the primary and gives
recovery_complete a chance to misread the primary never happens.
The fact that the primary can change has necessitated the change
to the default_mirror field. We need to protect against reading
garbage while the primary changes. We then add the bio to a new
list in the mirror set, 'failures'. For every bio in the 'failures'
list, we call a new function, '__bio_mark_nosync', where we mark
the region 'not-in-sync' in the log and properly set the region
state as, RH_NOSYNC. Userspace must also be notified of the
failure. This is done by 'raising an event' (dm_table_event()).
If fail_mirror is called in process context the event can be raised
right away. If in interrupt context, the event is deferred to the
kmirrord thread - which raises the event if 'event_waiting' is set.
Backwards compatibility is maintained by ignoring errors if
the DM_FEATURES_HANDLE_ERRORS flag is not present.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Milan Broz [Fri, 8 Feb 2008 02:11:27 +0000 (02:11 +0000)]
dm snapshot: combine consecutive exceptions in memory
Provided sector_t is 64 bits, reduce the in-memory footprint of the
snapshot exception table by the simple method of using unused bits of
the chunk number to combine consecutive entries.
Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Brian Wood [Fri, 8 Feb 2008 02:11:24 +0000 (02:11 +0000)]
dm: stripe enhanced status return
This patch adds additional information to the status line. It is added at the
end of the returned text so it will not interfere with existing
implementations using this data. The addition of this information will allow
for a common return interface to match that returned with the dm-raid1.c
status line (with Jonathan Brassow's patches).
Here is a sample of what is returned with a mirror "status" call:
isw_eeaaabgfg_mirror: 0 488390920 mirror 2 8:16 8:32 3727/3727 1 AA 1 core
Here's what's returned with this patch for a stripe "status" call:
isw_dheeijjdej_stripe: 0 976783872 striped 2 8:16 8:32 1 AA
Signed-off-by: Brian Wood <brian.j.wood@intel.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Brian Wood [Fri, 8 Feb 2008 02:11:22 +0000 (02:11 +0000)]
dm: stripe trigger event on failure
This patch adds the stripe_end_io function to process errors that might
occur after an IO operation. As part of this there are a number of
enhancements made to record and trigger events:
- New atomic variable in struct stripe to record the number of
errors each stripe volume device has experienced (could be used
later with uevents to report back directly to userspace)
- New workqueue/work struct setup to process the trigger_event function
- New end_io function. It is here that testing for BIO error conditions
take place. It determines the exact stripe that cause the error,
records this in the new atomic variable, and calls the queue_work() function
- New trigger_event function to process failure events. This
calls dm_table_event()
Signed-off-by: Brian Wood <brian.j.wood@intel.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Milan Broz [Fri, 8 Feb 2008 02:10:22 +0000 (02:10 +0000)]
dm: refactor deferred bio_list processing
Refactor deferred bio_list processing.
- use separate _merge_pushback_list function
- move deferred bio list pick up to flush function
- use bio_list_pop instead of bio_list_get
- simplify noflush flag use
No real functional change in this patch.
Signed-off-by: Milan Broz <mbroz@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Andrew Morton [Fri, 8 Feb 2008 02:10:11 +0000 (02:10 +0000)]
dm snapshot: use uninitialized_var
drivers/md/dm-exception-store.c: In function 'persistent_read_metadata':
drivers/md/dm-exception-store.c:452: warning: 'new_snapshot' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Linus Torvalds [Thu, 7 Feb 2008 21:21:02 +0000 (13:21 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
BKL-removal: Implement a compat_ioctl handler for JFS
BKL-removal: Use unlocked_ioctl for jfs
Jesse Barnes [Thu, 7 Feb 2008 19:15:20 +0000 (11:15 -0800)]
i915: Fix GR register array size off-by-one bug
Make sure we have enough room for all the GR registers or we'll end up
clobbering the AR index register (which should actually be harmless
unless the BIOS is making an assumption about it).
Andi Kleen [Sun, 27 Jan 2008 22:58:51 +0000 (16:58 -0600)]
BKL-removal: Use unlocked_ioctl for jfs
Convert jfs_ioctl over to not use the BKL. The only potential race
I could see was with two ioctls in parallel changing the flags
and losing the updates. Use the i_mutex to protect against this.
Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
It's possible that the caller of sysfs_remove_group messed up and passed in an attribute group that was not really registered to this kobject. But don't panic for such a foolish error, spit out a warning about what happened, and continue on our way safely.
The original patch breaks BIOS updates on all Dell machines. The path to
the firmware file for the dell_rbu driver changes, which breaks all of
the userspace tools which rely on it.
Note that this patch re-introduces a problem with i2c name collision
that was previously fixed by this patch.
Signed-off-by: Michael E Brown <michael_e_brown@dell.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "whole_disk" attribute was not properly converted in the block
device conversion earlier, and if the file is read, bad things can
happen. This patch fixes this, making the attribute an empty one,
preserving the original functionality.
Many thanks to David Miller for finding this, and pointing me in the
proper place within the block code to look.
Acked-by: David S. Miller <davem@davemloft.net> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Use regsets in arch_ptrace().
[SPARC64]: Use regsets in arch_ptrace().
[SPARC32]: Use regsets for ELF core dumping.
[SPARC64]: Use regsets for ELF core dumping.
[SPARC64]: Remove unintentional ptrace debugging messages.
[SPARC]: Move over to arch_ptrace().
[SPARC]: Remove PTRACE_SUN* handling.
[SPARC]: Kill DEBUG_PTRACE code.
[SPARC32]: Add user regset support.
[SPARC64]: Add user regsets.
[SPARC64]: Fix booting on non-zero cpu.
Linus Torvalds [Thu, 7 Feb 2008 18:20:31 +0000 (10:20 -0800)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6: (120 commits)
[MTD] Fix mtdoops.c compilation
[MTD] [NOR] fix startup lock when using multiple nor flash chips
[MTD] [DOC200x] eccbuf is statically defined and always evaluate to true
[MTD] Fix maps/physmap.c compilation with CONFIG_PM
[MTD] onenand: Add panic_write function to the onenand driver
[MTD] mtdoops: Use the panic_write function when present
[MTD] Add mtd panic_write function pointer
[MTD] [NAND] Freescale enhanced Local Bus Controller FCM NAND support.
[MTD] physmap.c: Add support for multiple resources
[MTD] [NAND] Fix misparenthesization introduced by commit 78b65179...
[MTD] [NAND] Fix Blackfin NFC ECC calculating bug with page size 512 bytes
[MTD] [NAND] Remove wrong operation in PM function of the BF54x NFC driver
[MTD] [NAND] Remove unused variable in plat_nand_remove
[MTD] Unlocking all Intel flash that is locked on power up.
[MTD] [NAND] at91_nand: Make mtdparts option can override board info
[MTD] mtdoops: Various minor cleanups
[MTD] mtdoops: Ensure sequential write to the buffer
[MTD] mtdoops: Perform write operations in a workqueue
[MTD] mtdoops: Add further error return code checking
[MTD] [NOR] Test devtype, not definition in flash_probe(), drivers/mtd/devices/lart.c
...
Linus Torvalds [Thu, 7 Feb 2008 17:45:14 +0000 (09:45 -0800)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Add HP Jornada 6xx driver
leds: Remove the now uneeded ixp4xx driver
leds: Add power LED to the wrap driver
leds: Fix led-gpio active_low default brightness
leds: hw acceleration for Clevo mail LED driver
leds: Add support for hardware accelerated LED flashing
leds: Standardise LED naming scheme
leds: Add clevo notebook LED driver
The recently introduced page walker (walk_page_range()) calls pgd_offset with a
const struct mm_struct pointer, causing the following compile warning on m68k:
mm/pagewalk.c:111: warning: passing argument 1 of 'pgd_offset' discards qualifiers from pointer target type
Make the `mm' parameter of the inline function pgd_offset() const to shut it
up.
Linus Torvalds [Thu, 7 Feb 2008 17:07:16 +0000 (09:07 -0800)]
Merge branch 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (22 commits)
drm: add initial r500 drm support
radeon: setup the ring buffer fetcher to be less agressive.
drm: fixup some of the ioctl function exit paths
drm: the drm really should call pci_set_master..
i915: Add chipset id for Intel Integrated Graphics Device
drm: cleanup DRM_DEBUG() parameters
drm/i915: add support for E7221 chipset
drm: don't cast a pointer to pointer of list_head
mga_dma: return 'err' not just zero from mga_do_cleanup_dma()
drm: add _DRM_DRIVER flag, and re-order unload.
drm: enable udev node creation
drm: Make DRM_IOCTL_GET_CLIENT return EINVAL when it can't find client #idx.
drm: move drm_mem_init to proper place in startup sequence
drm: call driver load function after initialising AGP
drm: Fix ioc32 compat layer
drm: fd.o bug #11895: Only add the AGP base to map offset if the caller didn't.
i915: add suspend/resume support
drm: update DRM sysfs support
drm: Initialize the AGP structure's base address at init rather than enable.
drm: move two function extern into the correct block
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Add missing printk levels to e_powersaver
[CPUFREQ] Fix sparse warning in powernow-k8
[CPUFREQ] Support Model D parts and newer in e_powersaver
[CPUFREQ] Powernow-k8: Update to support the latest Turion processors
[CPUFREQ] fix configuration help message
[CPUFREQ] powernow-k8 print pstate instead of fid/did for family 10h
[CPUFREQ] Eliminate cpufreq_userspace scaling_setspeed deadlock
[CPUFREQ] gx-suspmod.c: use boot_cpu_data instead of current_cpu_data
[CPUFREQ] fix incorrect comment on show_available_freqs() in freq_table.c
[CPUFREQ] drivers/cpufreq: Add missing "space"
[CPUFREQ] arch/x86: Add missing "space"
[CPUFREQ] Remove pointless Kconfig dependancy
Jiri Slaby [Thu, 7 Feb 2008 08:16:45 +0000 (00:16 -0800)]
Char: mxser, ioctl cleanup
- remove dead MOXA_GET_CONF (always returned -ENXIO)
- remove useless MOXA_GET_CUMAJOR (unused)
- use get/put_user instead of copy_from/to_user for simple types
- cleanup TIOCMIWAIT -- return -ERESTARTSYS on signal, move condition into
separate function
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Reviewed-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 7 Feb 2008 08:16:42 +0000 (00:16 -0800)]
Char: mxser, remove special baudrate processing
Let the special baudrate processing on the tty layer. Also remove
set/get_special_rate ioctls introduced in commit f64c84a1668930d1ca2b7dbaa92146c2139cb508, since it is no longer needed.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Reviewed-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 7 Feb 2008 08:16:40 +0000 (00:16 -0800)]
Char: serial167, remove bottomhalf
- Cy_EVENT_OPEN_WAKEUP is simple wake_up
- Cy_EVENT_HANGUP is wake_up + tty_hangup, which schedules its own work
- Cy_EVENT_WRITE_WAKEUP is tty_wakeup which may be called directly too
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 7 Feb 2008 08:16:39 +0000 (00:16 -0800)]
Char: stallion, remove bottomhalf
- tty_hangup schedules a bottomhalf itself, tty_wakeup doesn't need it
- call the CD code (part of work handler previously) directly from the code
(it wakes somebody up or calls tty_hangup at worse)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 7 Feb 2008 08:16:36 +0000 (00:16 -0800)]
Char: stallion, fix compiler warnings
Don't emit warnings on 64 bit platforms from min(). sizeof() on those
is not uint, neither 2 pointers difference, cast it to uint by min_t in
both cases.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 7 Feb 2008 08:16:33 +0000 (00:16 -0800)]
Char: rocket, printk cleanup
- add KERN_ level to each print
- change some levels appropriately
- add \n at the ends where missing
- change two complex printks into dev_info, where the original info is
printed automatically
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frank Sorenson [Thu, 7 Feb 2008 08:16:31 +0000 (00:16 -0800)]
i8k: Inspiron E1705 fix
Needs the following in order to work correctly on my Inspiron E1705:
Add DMI Product name to i8k for Dell MP061 hardware (Inspiron 9400/E1705)
Signed-off-by: Frank Sorenson <frank@tuxrocks.com> Cc: Bradley Smith <bradjsmith@btinternet.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bradley Smith [Thu, 7 Feb 2008 08:16:30 +0000 (00:16 -0800)]
I8K: add i8k driver to the x86_64 Kconfig
Adds i8k driver to the x86_64 Kconfig.
Signed-off-by: Bradley Smith <bradjsmith@btinternet.com> Cc: Frank Sorenson <frank@tuxrocks.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bradley Smith [Thu, 7 Feb 2008 08:16:27 +0000 (00:16 -0800)]
I8K: allow i8k driver to be built on x86_64 systems
Adds #if clause and additional inline assembly so that the driver
builds on x86_64 systems.
Signed-off-by: Bradley Smith <bradjsmith@btinternet.com> Cc: Frank Sorenson <frank@tuxrocks.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add cmpxchg_local to sparc, move __cmpxchg to system.h
Move cmpxchg and add cmpxchg_local to system.h.
Use the new generic cmpxchg_local (disables interrupt).
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: William Lee Irwin III <wli@holomorphy.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gunnar Larisch [Thu, 7 Feb 2008 08:16:22 +0000 (00:16 -0800)]
Add cmpxchg_local to ppc
Add a local processor version of cmpxchg for ppc.
Implements __cmpxchg_u32_local and uses it for 32 bits cmpxchg_local.
It uses the non NMI safe cmpxchg_local_generic for 1, 2 and 8 bytes
cmpxchg_local.
Signed-off-by: Gunnar Larisch <gl@denx.de> Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is for Mathieu Desnoyers's include/asm-m32r/local.h.
Applying the new include/asm-m32r/local.h, inclusion of linux/sched.h
is needed to fix a build error of arch/m32r/kernel/smpboot.c.
<-- snip -->
...
CC arch/m32r/kernel/smpboot.o
/project/m32r-linux/kernel/work/linux-2.6_dev.git/arch/m32r/kernel/smpboot.c: In function 'do_boot_cpu':
/project/m32r-linux/kernel/work/linux-2.6_dev.git/arch/m32r/kernel/smpboot.c:279: error: implicit declaration of function 'fork_idle'
/project/m32r-linux/kernel/work/linux-2.6_dev.git/arch/m32r/kernel/smpboot.c:279: warning: assignment makes pointer from integer without a cast
/project/m32r-linux/kernel/work/linux-2.6_dev.git/arch/m32r/kernel/smpboot.c:283: error: dereferencing pointer to incomplete type
/project/m32r-linux/kernel/work/linux-2.6_dev.git/arch/m32r/kernel/smpboot.c:289: error: dereferencing pointer to incomplete type
/project/m32r-linux/kernel/work/linux-2.6_dev.git/arch/m32r/kernel/smpboot.c:290: error: implicit declaration of function 'task_thread_info'
/project/m32r-linux/kernel/work/linux-2.6_dev.git/arch/m32r/kernel/smpboot.c:290: error: invalid type argument of '->'
/project/m32r-linux/kernel/work/linux-2.6_dev.git/arch/m32r/kernel/smpboot.c: In function 'start_secondary':
/project/m32r-linux/kernel/work/linux-2.6_dev.git/arch/m32r/kernel/smpboot.c:429: error: implicit declaration of function 'cpu_init'
make[2]: *** [arch/m32r/kernel/smpboot.o] Error 1
<-- snip -->
the #endif /* CONFIG_SMP */ should cover the default condition, or it may cause
bad parameter to be silently missed.
To make it work correctly, we have to remove the ifdef CONFIG SMP surrounding
__xchg_called_with_bad_pointer declaration. Thanks to Adrian Bunk for detecting
this.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Acked-by: Hirokazu Takata <takata@linux-m32r.org> Cc: Adrian Bunk <bunk@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cmpxchg_local and cmpxchg64_local will use the architecture specific
__cmpxchg_local_u32 for 32 bits arguments, and use the generic
__cmpxchg_local_generic for 8, 16 and 64 bits arguments.
projects / linux-2.6 / log