Russell King [Wed, 27 Sep 2006 14:38:34 +0000 (15:38 +0100)]
[ARM] Move rest of MMU setup code from mm-armv.c to mmu.c
If we're going to have mmu.c for code which is specific to the MMU
machines, we might as well move the other MMU initialisation
specific code from mm-armv.c into this new file. This also allows
us to make some functions static.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Paul Brook [Sun, 24 Sep 2006 15:54:40 +0000 (16:54 +0100)]
[ARM] 3860/1: Versatile PCI config byte accesses
The ARM Versatile board PCI config space read routines are broken for byte
accesses. The access uses a byte read, so masking the bottom two bits of the
address is wrong.
I guess this is a cut/paste error from the the halfword code which uses
aligned word access+shift+mask.
Signed-off-by: Paul Brook <paul@codesourcery.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM XIP_KERNEL map created in devicemaps_init() is wrong.
The map.pfn is rounded down to an even 1MiB section boundary
which results in va/pa translations errors when XIP_PHYS_ADDR
starts on an odd 1MiB boundary and this causes the kernel to
hang. This patch fixes ARM XIP_KERNEL translation errors for
the odd 1MiB XIP_PHYS_ADDR boundary case.
Signed-off-by: George G. Davis <gdavis@mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David Anders [Thu, 21 Sep 2006 21:57:12 +0000 (22:57 +0100)]
[ARM] 3854/2: S3C2410 - add machine type for AML M5900 series (resubmitted)
Add the AML M5900 series to the list of supported machines in the
arch/arm/mach-s3c2410 directory. This ensures the core peripherals
are registered, and the timer source is configured. if selected in
the kernel config the framebuffer registers and mtd partition
information are set. This version of the patch has corrected
formatting and removed the legacy procfs directory entry.
Signed-off-by: David Anders <danders@amltd.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Document the meaning for OP_SCALAR, OP_SD and add OP_DD.
- Formatting cleanups
- Remove now redundant code for making compare instructions
operate on scalar values.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gen FUKATSU [Thu, 21 Sep 2006 13:08:24 +0000 (14:08 +0100)]
[ARM] 3789/4: Fix VFP emulation to ignore VECITR for scalar instruction
VECITR in Floating-Point Exception register indicates the number of
remaining short vector iterations after a potential exception was
detected.
In case of exception caused by scalar instructions, VECITR is NOT updated.
Therefore emulation for VFP must ignore VECITR field
and treat "veclen" as zero when recognizing scalar instructing.
Signed-off-by: Gen Fukatsu <fukatsu.gen@jp.panasonic.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dan Fandrich [Wed, 20 Sep 2006 22:28:51 +0000 (23:28 +0100)]
[ARM] 3792/2: Fix description of ZBOOT_ROM_BSS
The documentation for the ZBOOT_ROM_BSS config option describes it as
"The base address of 64KiB of read/write memory in the target for the
ROM-able zImage..." In actuality, it requires more than 100 KiB of
space in addition to enough space to hold the decompressed kernel.
This patch fixes the description in the Kconfig file.
Signed-off-by: Dan Fandrich <dfandrich@intrinsyc.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
George G. Davis [Thu, 21 Sep 2006 02:57:04 +0000 (03:57 +0100)]
[ARM] 3853/1: Fix flush_ptrace_access() thinko for nonaliasing VIPT cache case
Fix thinko in the flush_ptrace_access() "if (expr)" for the ARM
VIPT non-aliasing cache case. We only need to flush cache when
VM_EXEC is set in vma->vm_flags but "if (expr) always evaluates
to true on UP systems for the ARM VIPT non-aliasing cache case.
Signed-off-by: George G. Davis <gdavis@mvista.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 3851/1: iop3xx: add io-data glantank support
Add support for the IO-Data GLAN Tank, from Martin Michlmayr.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Wed, 20 Sep 2006 20:57:06 +0000 (21:57 +0100)]
[ARM] 3846/1: S3C24XX: Fix osiris memory map
The memory mapping for the Osiris machine
are all off by one bit, and the base address
has been fixed for writing (bit25 is being
checked by the write, but not on read)
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Wed, 20 Sep 2006 19:32:33 +0000 (20:32 +0100)]
[ARM] 3840/1: S3C2412: Add machine VSTMS
Add new machine VSTMS
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Gleixner <tglx@linuxtronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the iop32x code isn't iop321-specific, and the iop33x code isn't
iop331-specfic, do a s/iop321/iop32x/ and s/iop331/iop33x/, and tidy up
the code to conform to the coding style guidelines somewhat better.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Revamp the iop3xx board support: move the support code for each iop
board type into its own file, start using platform serial and platform
physmap flash devices, switch to a per-board time tick rate, and get
rid of the ARCH_EP80219 and STEPD config options by doing the relevant
checks at run time.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 3825/1: iop3xx: use cp6 enable/disable macros
Add CP6 enable/disable sequences to the timekeeping code and the IRQ
code. As a result, we can't depend on CP6 access being enabled when
we enter get_irqnr_and_base anymore, so switch the latter over to
using memory-mapped accesses for now.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add macros to enable and disable access to CP6. On the iop3xx, enabling
CP6 access unfortunately also enables access to that coprocessor from
unprivileged code, so we need these macros to enable and disable access
to the coprocessor whenever we need to access it.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 3817/1: iop3xx: split the iop3xx mach into iop32x and iop33x
Split the iop3xx mach type into iop32x and iop33x -- split the config
symbols, and move the code in the mach-iop3xx directory to the mach-iop32x
and mach-iop33x directories.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Mon, 18 Sep 2006 09:19:06 +0000 (10:19 +0100)]
[ARM] 3806/2: S3C2412: Fix GPIO VA when only S3C2412 selected
The s3c24xx_va_gpio2 variable is only used
when the S3C2412 and another cpu-type is
being used in the kernel. This patch ensures
it is not set when it is not being used.
Fixes bug report by Thomas Gleixner.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 3814/1: move 80200 dma_inv_range() erratum check out of line
On stepping A0/A1 of the 80200, invalidating D-cache by line doesn't
clear the dirty bits, which means that if we invalidate a dirty line,
the dirty data can still be written back to memory later on.
To work around this, dma_inv_range() on these two processors is
implemented as dma_flush_range() (i.e. do a clean D-cache line before
doing the invalidate D-cache line.) For this, we currently have a
processor ID check in xscale_dma_inv_range(), but a better solution
is to add a separate cache_fns and proc_info for A0/A1 80200.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prevent userland from mapping in physical address regions >= 4G by
checking for that in valid_mmap_phys_addr_range().
Unfortunately, we cannot override valid_mmap_phys_addr_range() without
also overriding valid_phys_addr_range(), so copy drivers/char/mem.c's
version of valid_phys_addr_range() over to arch/arm/mm/mmap.c as well.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 3810/1: switch atomic helpers over to raw_local_irq_{save,restore}
Now that we have raw_* variants of local_irq_$FOO(), switch the atomic
helpers over to use those raw_* variants. This is necessary when using
lockdep on pre-ARMv6 hardware, as lockdep uses atomic_t counters in the
trace_hardirqs_off() path.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Fri, 15 Sep 2006 23:04:23 +0000 (00:04 +0100)]
[ARM] 3802/1: S3C24XX: PM tidy up cache flushing
Change to using flush_cache_all() in pm.c and
also remove the need to flush the cache in the
PM code.
This changes the sleep.S code to have an entry
to store the registers for resume, and then a
second entry (after the caches are cleaned)
to do the suspend and resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM kernel has several uses of asm("foo%?"). %? is a GCC internal
modifier used to output conditional execution predicates. However, no
version of GCC supports conditionalizing asm statements. GCC 4.2 will
correctly expand %? to the empty string in user asms. Earlier versions may
reuse the condition from the previous instruction. In 'if (foo) asm
("bar%?");' this is somewhat likely to be right... but not reliable.
So, the only safe thing to do is to remove the uses of %?. I believe
the tlbflush.h occurances were supposed to be removed before, based
on the comment about %? not working at the top of that file.
Old versions of GCC could omit branches around user asms if the asm didn't
mark the condition codes as clobbered. This problem hasn't been seen on any
recent (3.x or 4.x) GCC, but it could theoretically happen. So, where
%? was removed a cc clobber was added.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 27 Aug 2006 11:38:34 +0000 (12:38 +0100)]
[ARM] Optimise VFP thread notify function a little
The common case for the thread notifier is a context switch. Tell
gcc that this is the most likely condition so it can optimise the
function for this case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Sun, 27 Aug 2006 11:26:34 +0000 (12:26 +0100)]
[ARM] Fix kernel/fork.c for lockdep on ARM
ARM has interrupts enabled over context switches (iow, has
__ARCH_WANT_INTERRUPTS_ON_CTXSW defined.) The lockdep code in fork.c
assumes that interrupts are always disabled. Fix this wrong
assumption by making the initialisation of 'p->hardirqs_enabled'
depend on __ARCH_WANT_INTERRUPTS_ON_CTXSW.
Acked-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge branch 'fixes' of git://git.linux-nfs.org/pub/linux/nfs-2.6
* 'fixes' of git://git.linux-nfs.org/pub/linux/nfs-2.6:
NFS: Fix nfs_page use after free issues in fs/nfs/write.c
NFSv4: Fix incorrect semaphore release in _nfs4_do_open()
NFS: Fix Oopsable condition in nfs_readpage_sync()
Those changes were needed for EFI-environment Intel macs, but broke some
newer Intel 965 boards, so for now it's better to revert to our old
2.6.17 behaviour and at least avoid introducing any new breakage.
Andi Kleen has a set of patches that work with both EFI and the broken
Intel 965 boards, which will be applied once they get wider testing.
Cc: Arjan van de Ven <arjan@infradead.org> Cc: Edgar Hucek <hostmaster@ed-soft.at> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* git://git.infradead.org/mtd-2.6:
[MTD] Use SEEK_{SET,CUR,END} instead of hardcoded values in mtdchar lseek()
MTD: Fix bug in fixup_convert_atmel_pri
[JFFS2][SUMMARY] Fix a summary collecting bug.
[PATCH] [MTD] DEVICES: Fill more device IDs in the structure of m25p80
MTD: Add lock/unlock operations for Atmel AT49BV6416
MTD: Convert Atmel PRI information to AMD format
fs/jffs2/xattr.c: remove dead code
[PATCH] [MTD] Maps: Add dependency on alternate probe methods to physmap
[PATCH] MTD: Add Macronix MX29F040 to JEDEC
[MTD] Fixes of performance and stability issues in CFI driver.
block2mtd.c: Make kernel boot command line arguments work (try 4)
[MTD NAND] Fix lookup error in nand_get_flash_type()
remove #error on !PCI from pmc551.c
MTD: [NAND] Fix the sharpsl driver after breakage from a core conversion
[MTD] NAND: OOB buffer offset fixups
make fs/jffs2/nodelist.c:jffs2_obsolete_node_frag() static
[PATCH] [MTD] NAND: fix dead URL in Kconfig
Dave Kleikamp [Tue, 19 Sep 2006 03:12:33 +0000 (20:12 -0700)]
[PATCH] EXT2: Remove superblock lock contention in ext2_statfs
Fix a performance degradation introduced in 2.6.17. (30% degradation
running dbench with 16 threads)
Commit 21730eed11de42f22afcbd43f450a1872a0b5ea1, which claims to make
EXT2_DEBUG work again, moves the taking of the kernel lock out of
debug-only code in ext2_count_free_inodes and ext2_count_free_blocks and
into ext2_statfs.
Matthew Wilcox [Tue, 19 Sep 2006 03:12:27 +0000 (20:12 -0700)]
[PATCH] headers_check: Clean up asm-parisc/page.h for user headers
Remove definitions of PAGE_* from the user view
Delete unnecessary comments referring to the size of pages
Only include <asm-generic> if we're in __KERNEL__
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Kyle McMartin <kyle@parisc-linux.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
as it turns out, the bug is caused by handle_level_irq(), which if it
races with another CPU already handling this IRQ, it _unmasks_ the IRQ
line on the way out. This is not how 2.6.17 works, and we introduced
this bug in one of the early genirq cleanups right before it went into
-mm. (the bug was not in the genirq patchset for a long time, and we
didnt notice the bug due to the lack of -rt rebase to the new genirq
code. -rt, and hardirq-preemption in particular opens up such races much
wider than anything else.)
Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It turns out that eflags is important to save and restore not just
because of iopl, but due to the magic bits like the NT bit, which we
don't want leaking between different threads.
Tested-by: Mike Galbraith <efault@gmx.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[ATM] CLIP: Do not refer freed skbuff in clip_mkip().
[NET]: Drop tx lock in dev_watchdog_up
[PACKET]: Don't truncate non-linear skbs with mmaped IO
[NET]: Mark frame diverter for future removal.
[NETFILTER]: Add secmark headers to header-y
[ATM]: linux-atm-general mailing list is subscribers only
[ATM]: [he] when transmit fails, unmap the dma regions
[TCP] tcp-lp: update information to MAINTAINERS
[TCP] tcp-lp: bug fix for oops in 2.6.18-rc6
[BRIDGE]: random extra bytes on STP TCN packet
[IPV6]: Accept -1 for IPV6_TCLASS
[IPV6]: Fix tclass setting for raw sockets.
[IPVS]: remove the debug option go ip_vs_ftp
[IPVS]: Make sure ip_vs_ftp ports are valid
[IPVS]: auto-help for ip_vs_ftp
[IPVS]: Document the ports option to ip_vs_ftp in kernel-parameters.txt
[TCP]: Turn ABC off.
[NEIGH]: neigh_table_clear() doesn't free stats
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3815/1: headers_install support for ARM
[ARM] 3794/1: S3C24XX: do not defined set_irq_wake when no CONFIG_PM
[ARM] 3793/1: S3C2412: fix wrong serial info struct
[ARM] 3780/1: Fix iop321 cpuid
[ARM] 3786/1: pnx4008: update defconfig
[ARM] 3785/1: S3C2412: Fix idle code as default uses wrong clocks
[ARM] 3784/1: S3C2413: fix config for MACH_S3C2413/MACH_SMDK2413
Ben Dooks [Mon, 18 Sep 2006 12:30:17 +0000 (13:30 +0100)]
[ARM] 3793/1: S3C2412: fix wrong serial info struct
Patch from Ben Dooks
The S3C2440 serial info struct is being passed
through the S3C2412 serial info struct probe
routine.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Thomas Glexiner <tglx@linutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David S. Miller [Mon, 18 Sep 2006 08:47:13 +0000 (01:47 -0700)]
[OPENPROMIO]: Handle current_node being NULL correctly.
If the user tries to traverse to the next node of the
last node, we get NULL in current_node and a zero phandle
returned. That's fine, but if the user tries to obtain
properties in that state, we try to dereference a NULL
pointer in the downcall to the of_*() routines.
So protect against that.
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 18 Sep 2006 07:22:30 +0000 (00:22 -0700)]
[NET]: Drop tx lock in dev_watchdog_up
Fix lockdep warning with GRE, iptables and Speedtouch ADSL, PPP over ATM.
On Sat, Sep 02, 2006 at 08:39:28PM +0000, Krzysztof Halasa wrote:
>
> =======================================================
> [ INFO: possible circular locking dependency detected ]
> -------------------------------------------------------
> swapper/0 is trying to acquire lock:
> (&dev->queue_lock){-+..}, at: [<c02c8c46>] dev_queue_xmit+0x56/0x290
>
> but task is already holding lock:
> (&dev->_xmit_lock){-+..}, at: [<c02c8e14>] dev_queue_xmit+0x224/0x290
>
> which lock already depends on the new lock.
This turns out to be a genuine bug. The queue lock and xmit lock are
intentionally taken out of order. Two things are supposed to prevent
dead-locks from occuring:
1) When we hold the queue_lock we're supposed to only do try_lock on the
tx_lock.
2) We always drop the queue_lock after taking the tx_lock and before doing
anything else.
>
> the existing dependency chain (in reverse order) is:
>
> -> #1 (&dev->_xmit_lock){-+..}:
> [<c012e7b6>] lock_acquire+0x76/0xa0
> [<c0336241>] _spin_lock_bh+0x31/0x40
> [<c02d25a9>] dev_activate+0x69/0x120
This path obviously breaks assumption 1) and therefore can lead to ABBA
dead-locks.
I've looked at the history and there seems to be no reason for the lock
to be held at all in dev_watchdog_up. The lock appeared in day one and
even there it was unnecessary. In fact, people added __dev_watchdog_up
precisely in order to get around the tx lock there.
The function dev_watchdog_up is already serialised by rtnl_lock since
its only caller dev_activate is always called under it.
So here is a simple patch to remove the tx lock from dev_watchdog_up.
In 2.6.19 we can eliminate the unnecessary __dev_watchdog_up and
replace it with dev_watchdog_up.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Mon, 18 Sep 2006 06:59:57 +0000 (23:59 -0700)]
[PACKET]: Don't truncate non-linear skbs with mmaped IO
Non-linear skbs are truncated to their linear part with mmaped IO.
Fix by using skb_copy_bits instead of memcpy.
Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
The code for frame diverter is unmaintained and has bitrotted.
The number of users is very small and the code has lots of problems.
If anyone is using it, they maybe exposing themselves to bad packet attacks.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
James Morris [Thu, 14 Sep 2006 04:04:55 +0000 (21:04 -0700)]
[NETFILTER]: Add secmark headers to header-y
This patch includes xt_SECMARK.h and xt_CONNSECMARK.h to the kernel
headers which are exported via 'make headers_install'. This is needed to
allow userland code to be built correctly with these features.
Please apply, and consider for inclusion with 2.6.18 as a bugfix.
Signed-off-by: James Morris <jmorris@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Sorry that the patch submited yesterday still contain a small bug.
This version have already been test for hours with BT connections. The
oops is now difficult to reproduce.
Signed-off-by: Wong Hoi Sing Edison <hswong3i@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log