This patch fixes the configuration dependencies in the vmcoreinfo data.
i386's "node_data" is defined in arch/x86/mm/discontig_32.c,
and x86_64's one is defined in arch/x86/mm/numa_64.c.
They depend on CONFIG_NUMA:
arch/x86/mm/Makefile_32:7
obj-$(CONFIG_NUMA) += discontig_32.o
arch/x86/mm/Makefile_64:7
obj-$(CONFIG_NUMA) += numa_64.o
ia64's "pgdat_list" is defined in arch/ia64/mm/discontig.c,
and it depends on CONFIG_DISCONTIGMEM and CONFIG_SPARSEMEM:
arch/ia64/mm/Makefile:9-10
obj-$(CONFIG_DISCONTIGMEM) += discontig.o
obj-$(CONFIG_SPARSEMEM) += discontig.o
ia64's "node_memblk" is defined in arch/ia64/mm/numa.c,
and it depends on CONFIG_NUMA:
arch/ia64/mm/Makefile:8
obj-$(CONFIG_NUMA) += numa.o
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp> Acked-by: Simon Horman <horms@verge.net.au> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
vmcoreinfo: rename vmcoreinfo's macros returning the size
This patchset is for the vmcoreinfo data.
The vmcoreinfo data has the minimum debugging information only for dump
filtering. makedumpfile (dump filtering command) gets it to distinguish
unnecessary pages, and makedumpfile creates a small dumpfile.
This patch:
VMCOREINFO_SIZE() should be renamed VMCOREINFO_STRUCT_SIZE() since it's always
returning the size of the struct with a given name. This change would allow
VMCOREINFO_TYPEDEF_SIZE() to simply become VMCOREINFO_SIZE() since it need not
be used exclusively for typedefs.
This discussion is the following:
http://www.ussg.iu.edu/hypermail/linux/kernel/0709.3/0582.html
Signed-off-by: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp> Acked-by: David Rientjes <rientjes@google.com> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bernhard Walle [Thu, 7 Feb 2008 08:15:19 +0000 (00:15 -0800)]
Use BOOTMEM_EXCLUSIVE for kdump
Use the BOOTMEM_EXCLUSIVE, introduced in the previous patch, to avoid
conflicts while reserving the memory for the kdump capture kernel
(crashkernel=).
Signed-off-by: Bernhard Walle <bwalle@suse.de> Cc: <linux-arch@vger.kernel.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@in.ibm.com> Acked-by: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bernhard Walle [Thu, 7 Feb 2008 08:15:17 +0000 (00:15 -0800)]
Introduce flags for reserve_bootmem()
This patchset adds a flags variable to reserve_bootmem() and uses the
BOOTMEM_EXCLUSIVE flag in crashkernel reservation code to detect collisions
between crashkernel area and already used memory.
This patch:
Change the reserve_bootmem() function to accept a new flag BOOTMEM_EXCLUSIVE.
If that flag is set, the function returns with -EBUSY if the memory already
has been reserved in the past. This is to avoid conflicts.
Because that code runs before SMP initialisation, there's no race condition
inside reserve_bootmem_core().
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix powerpc build] Signed-off-by: Bernhard Walle <bwalle@suse.de> Cc: <linux-arch@vger.kernel.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Vivek Goyal <vgoyal@in.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Thu, 7 Feb 2008 08:15:16 +0000 (00:15 -0800)]
fs menu: small reorg
- move minixfs and ROMfs to the Miscellaneous filesystems menu
- move DNOTIFY config symbol so that it is adjacent to INOTIFY
instead of being split by the QUOTA config options
- add some 'endif' annotations
- remove some whitespace (extra blank lines)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a set of changes to implement proper resource management in the
driver, including iomem space reservation and operating on physical
addresses ioremap()ped appropriately using accessory functions rather than
unportable direct assignments.
Some adjustments to code are made to reflect the architecture of the
interface, which is a centrally controlled multiport (or, as referred to
from DEC documentation, a serial line multiplexer, going up to 8 lines
originally) rather than a bundle of separate ports.
Types are changed, where applicable, to specify the width of hardware
registers explicitly. The interrupt handler is now managed in the
->startup() and ->shutdown() calls for consistency with other drivers and
also in preparation to handle the handover from the initial firmware-based
console gracefully.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dz.c: Use a helper to cast from "struct uart_port *"
Replace all casts from "struct uart_port *" to "struct dz_port *" with a
construct based on container_of(). This makes the conversion work
irrespective of where the former struct is located within the latter.
By popular request I have implemented it as an inline function rather than
a macro this time.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dz: clean up and improve the setup of termios settings
A set of changes to the way termios settings are propagated to the serial
port hardware. The DZ11 only supports a selection of fixed baud settings,
so some requests may not be fulfilled. Keep the old setting in such a case
and failing that resort to 9600bps. Also add a missing update of the
transmit timeout. And remove the explicit encoding of the line selected
from writes to the Line Parameters Register as it has been preencoded by
the ->set_termios() call already. Finally, remove a duplicate macro for
the Receiver Enable bit.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that I have got the necessary piece of hardware (thanks, Thiemo!), I may
well offer myself as the maintainer for the dz serial driver. I hope nobody
objects.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dz: handle special conditions on reception correctly
Handle the read and ignore status masks correctly. Handle the BREAK condition
as expected: a framing error with a null character is a BREAK, any other
framing error is a framing error indeed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ->start_tx(), ->stop_tx() and ->stop_rx() backends are called with the
port's lock already taken. Remove locking from within them and wrap around
calls as necessary.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat the Kconfig entries and update descriptions for accuracy. Select the
driver by default for configurations of interest. For the curious: 32BIT
means only 32-bit DECstations support the device, not that the driver is not
64-bit clean; I have not checked that either though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Well, panic() is a little bit undue if request_irq() fails; there is probably
no need to justify it any further. Handle the case gracefully, by
unregistering the driver.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dz: always check if it is safe to console_putchar()
Polled transmission is tricky enough with the DZ11 design. While "loop" is
set to a high value, conceptually you are not allowed to transmit without
checking whether the device offers the right transmission line (yes, it is the
device that selects the line -- the driver has no control over it other than
disabling the transmitter offered if it is the wrong one), so the loop has to
be run at least once.
Well, the '1977 or PDP11 view of how serial lines should be handled... Except
that the serial interface used to be quite an impressive board back then
rather than chip.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Cc: Jiri Slaby <jirislaby@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bryan Boatright [Thu, 7 Feb 2008 08:14:58 +0000 (00:14 -0800)]
drivers/edac: pci: broken parity regression
Using the EDAC code in kernel.org kernel version 2.6.23.8 I am seeing the
following problem:
In the kernel there is a pci device attribute located in sysfs that is
checked by the EDAC PCI scanning code. If that attribute is set,
PCI parity/error scannining is skipped for that device. The attribute
is:
broken_parity_status
as is located in /sys/devices/pci<XXX>/0000:XX:YY.Z directorys for
PCI devices.
I don't think this check was actually implemented. I have a misbehaved card
that reports a parity error every 1000 ms:
Nov 25 07:28:43 beta kernel: EDAC PCI: Master Data Parity Error on 0000:05:01.0
Nov 25 07:28:44 beta kernel: EDAC PCI: Master Data Parity Error on 0000:05:01.0
Nov 25 07:28:45 beta kernel: EDAC PCI: Master Data Parity Error on 0000:05:01.0
Setting that card's broken_parity_status bit did not mask the error:
I looked through the EDAC code and did not readily see any reference to
broken_parity_status at all (which makes sense based on the behavior I am
seeing). I applied the following patch as a proof-of-concept and now EDAC's
PCI parity error reporting behaves as documented:
bryan
Good regression find, bryan. It used to work. sigh.
I added more logic to your patch, for more coverage of the error.
Dave Jiang [Thu, 7 Feb 2008 08:14:56 +0000 (00:14 -0800)]
drivers-edac: add marvell mv64x60 driver
Marvell mv64x60 SoC support for EDAC. Used on PPC and MIPS platforms.
Development and testing done on PPC Motorola prpmc2800 ATCA board.
[akpm@linux-foundation.org: make mv64x60_ctl_name static] Signed-off-by: Dave Jiang <djiang@mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk Signed-off-by: Douglas Thompson <dougthompson@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adds driver for the Cell memory controller when used without a Hypervisor such
as on the IBM Cell blades. There might still be some improvements to do to
this such as finding if it's possible to properly obtain more details about
the address of the error but it's good enough already to report CE counts
which is our main priority at the moment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk Signed-off-by: Doug Thompson <dougthompson@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Blanchard [Thu, 7 Feb 2008 08:14:51 +0000 (00:14 -0800)]
drivers-edac: use round_jiffies_relative
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Arjan van de Ven <arjan@linux.intel.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk Signed-off-by: Doug Thompson <dougthompson@xmission.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Samuel Ortiz [Thu, 7 Feb 2008 08:14:49 +0000 (00:14 -0800)]
ASIC3 driver
This is a patch for the Compaq ASIC3 multi function chip, found in many
PDAs (iPAQs, HTCs...).
It is a simplified version of Paul Sokolovsky's first proposal [1]. With
this code, it is basically a GPIO and IRQ expander. My plan is to add more
features once this patch gets reviewed and accepted.
[1] http://lkml.org/lkml/2007/5/1/46
Signed-off-by: Samuel Ortiz <sameo@openedhand.com> Cc: Paul Sokolovsky <pmiscml@gmail.com> Cc: Ben Dooks <ben@trinity.fluff.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Jackson [Thu, 7 Feb 2008 08:14:48 +0000 (00:14 -0800)]
cpusets: update_cpumask documentation fix
Update cpuset documentation to match the October 2007 "Fix cpusets
update_cpumask" changes that now apply changes to a cpusets 'cpus' allowed
mask immediately to the cpus_allowed of the tasks in that cpuset.
Signed-off-by: Paul Jackson <pj@sgi.com> Acked-by: Cliff Wickman <cpw@sgi.com> Cc: David Rientjes <rientjes@google.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pavel Emelyanov [Thu, 7 Feb 2008 08:14:47 +0000 (00:14 -0800)]
Handle pid namespaces in cgroups code
There's one place that works with task pids - its the "tasks" file in cgroups.
The read/write handlers assume, that the pid values go to/come from the user
space and thus it is a virtual pid, i.e. the pid as it is seen from inside a
namespace.
Tune the code accordingly.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Acked-by: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Jackson [Thu, 7 Feb 2008 08:14:47 +0000 (00:14 -0800)]
hotplug cpu move tasks in empty cpusets - refinements
- Narrow the scope of callback_mutex in scan_for_empty_cpusets().
- Avoid rewriting the cpus, mems of cpusets except when it is likely that
we'll be changing them.
- Have remove_tasks_in_empty_cpuset() also check for empty mems.
Signed-off-by: Paul Jackson <pj@sgi.com> Acked-by: Cliff Wickman <cpw@sgi.com> Cc: David Rientjes <rientjes@google.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Jackson [Thu, 7 Feb 2008 08:14:46 +0000 (00:14 -0800)]
hotplug cpu: move tasks in empty cpusets to parent various other fixes
Various minor formatting and comment tweaks to Cliff Wickman's
[PATCH_3_of_3]_cpusets__update_cpumask_revision.patch
I had had "iff", meaning "if and only if" in a comment. However, except for
ancient mathematicians, the abbreviation "iff" was a tad too cryptic. Cliff
changed it to "if", presumably figuring that the "iff" was a typo. However,
it was the "only if" half of the conjunction that was most interesting.
Reword to emphasis the "only if" aspect.
The locking comment for remove_tasks_in_empty_cpuset() was wrong; it said
callback_mutex had to be held on entry. The opposite is true.
Several mentions of attach_task() in comments needed to be
changed to cgroup_attach_task().
A comment about notify_on_release was no longer relevant,
as the line of code it had commented, namely:
set_bit(CS_RELEASED_RESOURCE, &parent->flags);
is no longer present in that place in the cpuset.c code.
Similarly a comment about notify_on_release before the
scan_for_empty_cpusets() routine was no longer relevant.
Removed extra parentheses and unnecessary return statement.
Renamed attach_task() to cpuset_attach() in various comments.
Removed comment about not needing memory migration, as it seems the migration
is done anyway, via the cpuset_attach() callback from cgroup_attach_task().
Signed-off-by: Paul Jackson <pj@sgi.com> Acked-by: Cliff Wickman <cpw@sgi.com> Cc: David Rientjes <rientjes@google.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Menage [Thu, 7 Feb 2008 08:14:45 +0000 (00:14 -0800)]
cgroups: update comments in cpuset.c
Some of the comments in kernel/cpuset.c were stale following the
transition to control groups; this patch updates them to more closely
match reality.
Signed-off-by: Paul Menage <menage@google.com> Acked-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cliff Wickman [Thu, 7 Feb 2008 08:14:43 +0000 (00:14 -0800)]
hotplug cpu: move tasks in empty cpusets to parent
This patch corrects a situation that occurs when one disables all the cpus in
a cpuset.
Currently, the disabled (cpu-less) cpuset inherits the cpus of its parent,
which is incorrect because it may then overlap its cpu-exclusive sibling.
Tasks of an empty cpuset should be moved to the cpuset which is the parent of
their current cpuset. Or if the parent cpuset has no cpus, to its parent,
etc.
And the empty cpuset should be released (if it is flagged notify_on_release).
Depends on the cgroup_scan_tasks() function (proposed by David Rientjes) to
iterate through all tasks in the cpu-less cpuset. We are deliberately
avoiding a walk of the tasklist.
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Cliff Wickman <cpw@sgi.com> Cc: Paul Menage <menage@google.com> Cc: Paul Jackson <pj@sgi.com> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cliff Wickman [Thu, 7 Feb 2008 08:14:42 +0000 (00:14 -0800)]
cgroups: mechanism to process each task in a cgroup
Provide cgroup_scan_tasks(), which iterates through every task in a cgroup,
calling a test function and a process function for each. And call the process
function without holding the css_set_lock lock.
The idea is David Rientjes', predicting that such a function will make it much
easier in the future to extend things that require access to each task in a
cgroup without holding the lock,
[akpm@linux-foundation.org: cleanup]
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Cliff Wickman <cpw@sgi.com> Cc: Paul Menage <menage@google.com> Cc: Paul Jackson <pj@sgi.com> Acked-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Balbir Singh [Thu, 7 Feb 2008 08:14:41 +0000 (00:14 -0800)]
Memory controller remove control_type feature
Based on the discussion at http://lkml.org/lkml/2007/12/20/383, it was felt
that control_type might not be a good thing to implement right away. We
can add this flexibility at a later point when required.
per-zone and reclaim enhancements for memory controller: modifies vmscan.c for isolate globa/cgroup lru activity
When using memory controller, there are 2 levels of memory reclaim.
1. zone memory reclaim because of system/zone memory shortage.
2. memory cgroup memory reclaim because of hitting limit.
These two can be distinguished by sc->mem_cgroup parameter.
(scan_global_lru() macro)
This patch tries to make memory cgroup reclaim routine avoid affecting
system/zone memory reclaim. This patch inserts if (scan_global_lru()) and
hook to memory_cgroup reclaim support functions.
This patch can be a help for isolating system lru activity and group lru
activity and shows what additional functions are necessary.
* mem_cgroup_calc_mapped_ratio() ... calculate mapped ratio for cgroup.
* mem_cgroup_reclaim_imbalance() ... calculate active/inactive balance in
cgroup.
* mem_cgroup_calc_reclaim_active() ... calculate the number of active pages to
be scanned in this priority in mem_cgroup.
* mem_cgroup_calc_reclaim_inactive() ... calculate the number of inactive pages
to be scanned in this priority in mem_cgroup.
* mem_cgroup_all_unreclaimable() .. checks cgroup's page is all unreclaimable
or not.
* mem_cgroup_get_reclaim_priority() ...
* mem_cgroup_note_reclaim_priority() ... record reclaim priority (temporal)
* mem_cgroup_remember_reclaim_priority()
.... record reclaim priority as
zone->prev_priority.
This value is used for calc reclaim_mapped.
[akpm@linux-foundation.org: fix unused var warning] Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: David Rientjes <rientjes@google.com> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: Kirill Korotaev <dev@sw.ru> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Paul Menage <menage@google.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
per-zone and reclaim enhancements for memory controller: per-zone active inactive counter
This patch adds per-zone status in memory cgroup. These values are often read
(as per-zone value) by page reclaiming.
In current design, per-zone stat is just a unsigned long value and not an
atomic value because they are modified only under lru_lock. (So, atomic_ops
is not necessary.)
This patch adds ACTIVE and INACTIVE per-zone status values.
For handling per-zone status, this patch adds
struct mem_cgroup_per_zone {
...
}
and some helper functions. This will be useful to add per-zone objects
in mem_cgroup.
This patch turns memory controller's early_init to be 0 for calling
kmalloc() in initialization.
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: David Rientjes <rientjes@google.com> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: Kirill Korotaev <dev@sw.ru> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Paul Menage <menage@google.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
per-zone and reclaim enhancements for memory controller: add scan_global_lru macro
This is used to detect which scan_control scans global lru or mem_cgroup lru.
And compiled to be static value (1) when memory controller is not configured.
This may make the meaning obvious.
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: David Rientjes <rientjes@google.com> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: Kirill Korotaev <dev@sw.ru> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Paul Menage <menage@google.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a handler "pre_destroy" to cgroup_subsys. It is called before
cgroup_rmdir() checks all subsys's refcnt.
I think this is useful for subsys which have some extra refs even if there
are no tasks in cgroup. By adding pre_destroy(), the kernel keeps the rule
"destroy() against subsystem is called only when refcnt=0." and allows css
ref to be used by other objects than tasks.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: David Rientjes <rientjes@google.com> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: Kirill Korotaev <dev@sw.ru> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Paul Menage <menage@google.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memory cgroup enhancements: add status accounting function for memory cgroup
Add statistics account infrastructure for memory controller. All account
information is stored per-cpu and caller will not have to take lock or use
atomic ops. This will be used by memory.stat file later.
CACHE includes swapcache now. I'd like to divide it to
PAGECACHE and SWAPCACHE later.
This patch adds 3 functions for accounting.
* __mem_cgroup_stat_add() ... for usual routine.
* __mem_cgroup_stat_add_safe ... for calling under irq_disabled section.
* mem_cgroup_read_stat() ... for reading stat value.
* renamed PAGECACHE to CACHE (because it may include swapcache *now*)
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix smp_processor_id-in-preemptible]
[akpm@linux-foundation.org: uninline things]
[akpm@linux-foundation.org: remove dead code] Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: YAMAMOTO Takashi <yamamoto@valinux.co.jp> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Cc: Kirill Korotaev <dev@sw.ru> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Paul Menage <menage@google.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Thu, 7 Feb 2008 08:14:22 +0000 (00:14 -0800)]
memcgroup: fix hang with shmem/tmpfs
The memcgroup regime relies upon a cgroup reclaiming pages from itself within
add_to_page_cache: which may involve some waiting. Whereas shmem and tmpfs
rely upon using add_to_page_cache while holding a spinlock: when it cannot
wait. The consequence is that when a cgroup reaches its limit, shmem_getpage
just hangs - unless there is outside memory pressure too, neither kswapd nor
radix_tree_preload get it out of the retry loop.
In most cases we can mem_cgroup_cache_charge the page waitably first, to
attach the page_cgroup in advance, so add_to_page_cache will do no more than
increment a count; then mem_cgroup_uncharge_page after (in both success and
failure cases) to balance the books again.
And where there used to be a congestion_wait for kswapd (recently made
redundant by radix_tree_preload), use mem_cgroup_cache_charge with NULL page
to go through a cycle of allocation and freeing, without accounting to any
particular page, and without updating the statistics vector. This brings the
cgroup below its limit so the next try usually succeeds.
Hugh Dickins [Thu, 7 Feb 2008 08:14:19 +0000 (00:14 -0800)]
memcgroup: tidy up mem_cgroup_charge_common
Tidy up mem_cgroup_charge_common before extending it. Adjust some comments,
but mainly clean up its loop: I've an aversion to loops full of continues,
then a break or a goto at the bottom. And the is_atomic test should be on the
__GFP_WAIT bit, not GFP_ATOMIC bits.
memory cgroup enhancements: remember "a page is charged as page cache"
Add a flag to page_cgroup to remember "this page is
charged as cache."
cache here includes page caches and swap cache.
This is useful for implementing precise accounting in memory cgroup.
TODO:
distinguish page-cache and swap-cache
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: YAMAMOTO Takashi <yamamoto@valinux.co.jp> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
memory cgroup enhancements: fix zone handling in try_to_free_mem_cgroup_page
Because NODE_DATA(node)->node_zonelists[] is guaranteed to contain all
necessary zones, it is not necessary to use for_each_online_node.
And this for_each_online_node() makes reclaim routine start always
from node 0. This is not good. This patch makes reclaim start from
caller's node and just use usual (default) zonelist order.
[akpm@linux-foundation.org: fix warning] Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Thu, 7 Feb 2008 08:14:13 +0000 (00:14 -0800)]
memcgroup: revert swap_state mods
If we're charging rss and we're charging cache, it seems obvious that we
should be charging swapcache - as has been done. But in practice that
doesn't work out so well: both swapin readahead and swapoff leave the
majority of pages charged to the wrong cgroup (the cgroup that happened to
read them in, rather than the cgroup to which they belong).
(Which is why unuse_pte's GFP_KERNEL while holding pte lock never showed up
as a problem: no allocation was ever done there, every page read being
already charged to the cgroup which initiated the swapoff.)
It all works rather better if we leave the charging to do_swap_page and
unuse_pte, and do nothing for swapcache itself: revert mm/swap_state.c to
what it was before the memory-controller patches. This also speeds up
significantly a contained process working at its limit: because it no
longer needs to keep waiting for swap writeback to complete.
Is it unfair that swap pages become uncharged once they're unmapped, even
though they're still clearly private to particular cgroups? For a short
while, yes; but PageReclaim arranges for those pages to go to the end of
the inactive list and be reclaimed soon if necessary.
shmem/tmpfs pages are a distinct case: their charging also benefits from
this change, but their second life on the lists as swapcache pages may
prove more unfair - that I need to check next.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Cc: Pavel Emelianov <xemul@openvz.org> Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Thu, 7 Feb 2008 08:14:12 +0000 (00:14 -0800)]
memcgroup: fix zone isolation OOM
mem_cgroup_charge_common shows a tendency to OOM without good reason, when
a memhog goes well beyond its rss limit but with plenty of swap available.
Seen on x86 but not on PowerPC; seen when the next patch omits swapcache
from memcgroup, but we presume it can happen without.
mem_cgroup_isolate_pages is not quite satisfying reclaim's criteria for OOM
avoidance. Already it has to scan beyond the nr_to_scan limit when it
finds a !LRU page or an active page when handling inactive or an inactive
page when handling active. It needs to do exactly the same when it finds a
page from the wrong zone (the x86 tests had two zones, the PowerPC tests
had only one).
Don't increment scan and then decrement it in these cases, just move the
incrementation down. Fix recent off-by-one when checking against
nr_to_scan. Cut out "Check if the meta page went away from under us",
presumably left over from early debugging: no amount of such checks could
save us if this list really were being updated without locking.
This change does make the unlimited scan while holding two spinlocks
even worse - bad for latency and bad for containment; but that's a
separate issue which is better left to be fixed a little later.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Cc: Pavel Emelianov <xemul@openvz.org> Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bugfix for memory cgroup controller: avoid !PageLRU page in mem_cgroup_isolate_pages
This patch makes mem_cgroup_isolate_pages() to be
- ignore !PageLRU pages.
- fixes the bug that isolation makes no progress if page_zone(page) != zone
page once find. (just increment scan in this case.)
kswapd and memory migration removes a page from list when it handles
a page for reclaiming/migration.
Because __isolate_lru_page() doesn't moves page !PageLRU pages, it will
be safe to avoid touching !PageLRU() page and its page_cgroup.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bugfix for memory cgroup controller: migration under memory controller fix
While using memory control cgroup, page-migration under it works as following.
==
1. uncharge all refs at try to unmap.
2. charge regs again remove_migration_ptes()
==
This is simple but has following problems.
==
The page is uncharged and charged back again if *mapped*.
- This means that cgroup before migration can be different from one after
migration
- If page is not mapped but charged as page cache, charge is just ignored
(because not mapped, it will not be uncharged before migration)
This is memory leak.
==
This patch tries to keep memory cgroup at page migration by increasing
one refcnt during it. 3 functions are added.
mem_cgroup_prepare_migration() --- increase refcnt of page->page_cgroup
mem_cgroup_end_migration() --- decrease refcnt of page->page_cgroup
mem_cgroup_page_migration() --- copy page->page_cgroup from old page to
new page.
During migration
- old page is under PG_locked.
- new page is under PG_locked, too.
- both old page and new page is not on LRU.
These 3 facts guarantee that page_cgroup() migration has no race.
Tested and worked well in x86_64/fake-NUMA box.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rik van Riel [Thu, 7 Feb 2008 08:14:08 +0000 (00:14 -0800)]
kswapd should only wait on IO if there is IO
The current kswapd (and try_to_free_pages) code has an oddity where the
code will wait on IO, even if there is no IO in flight. This problem is
notable especially when the system scans through many unfreeable pages,
causing unnecessary stalls in the VM.
Additionally, tasks without __GFP_FS or __GFP_IO in the direct reclaim path
will sleep if a significant number of pages are encountered that should be
written out. This gives kswapd a chance to write out those pages, while
the direct reclaim task sleeps.
Signed-off-by: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Thu, 7 Feb 2008 08:14:07 +0000 (00:14 -0800)]
oom: add sysctl to enable task memory dump
Adds a new sysctl, 'oom_dump_tasks', that enables the kernel to produce a
dump of all system tasks (excluding kernel threads) when performing an
OOM-killing. Information includes pid, uid, tgid, vm size, rss, cpu,
oom_adj score, and name.
This is helpful for determining why there was an OOM condition and which
rogue task caused it.
It is configurable so that large systems, such as those with several
thousand tasks, do not incur a performance penalty associated with dumping
data they may not desire.
If an OOM was triggered as a result of a memory controller, the tasklist
shall be filtered to exclude tasks that are not a member of the same
cgroup.
Cc: Andrea Arcangeli <andrea@suse.de> Cc: Christoph Lameter <clameter@sgi.com> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Thu, 7 Feb 2008 08:14:06 +0000 (00:14 -0800)]
memcontrol: move oom task exclusion to tasklist scan
Creates a helper function to return non-zero if a task is a member of a
memory controller:
int task_in_mem_cgroup(const struct task_struct *task,
const struct mem_cgroup *mem);
When the OOM killer is constrained by the memory controller, the exclusion
of tasks that are not a member of that controller was previously misplaced
and appeared in the badness scoring function. It should be excluded
during the tasklist scan in select_bad_process() instead.
[akpm@linux-foundation.org: build fix] Cc: Christoph Lameter <clameter@sgi.com> Cc: Balbir Singh <balbir@linux.vnet.ibm.com> Signed-off-by: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Balbir Singh [Thu, 7 Feb 2008 08:14:05 +0000 (00:14 -0800)]
memory controller BUG_ON()
Move mem_controller_cache_charge() above radix_tree_preload().
radix_tree_preload() disables preemption, even though the gfp_mask passed
contains __GFP_WAIT, we cannot really do __GFP_WAIT allocations, thus we
hit a BUG_ON() in kmem_cache_alloc().
This patch moves mem_controller_cache_charge() to above radix_tree_preload()
for cache charging.
Hugh Dickins [Thu, 7 Feb 2008 08:14:04 +0000 (00:14 -0800)]
memcgroup: reinstate swapoff mod
This patch reinstates the "swapoff: scan ptes preemptibly" mod we started
with: in due course it should be rendered down into the earlier patches,
leaving us with a more straightforward mem_cgroup_charge mod to unuse_pte,
allocating with GFP_KERNEL while holding no spinlock and no atomic kmap.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Cc: Pavel Emelianov <xemul@openvz.org> Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Rientjes [Thu, 7 Feb 2008 08:14:03 +0000 (00:14 -0800)]
memcontrol: move mm_cgroup to header file
Inline functions must preceed their use, so mm_cgroup() should be defined
in linux/memcontrol.h.
include/linux/memcontrol.h:48: warning: 'mm_cgroup' declared inline after
being called
include/linux/memcontrol.h:48: warning: previous declaration of
'mm_cgroup' was here
Balbir Singh [Thu, 7 Feb 2008 08:14:02 +0000 (00:14 -0800)]
Memory controller: make charging gfp mask aware
Nick Piggin pointed out that swap cache and page cache addition routines
could be called from non GFP_KERNEL contexts. This patch makes the
charging routine aware of the gfp context. Charging might fail if the
cgroup is over it's limit, in which case a suitable error is returned.
This patch was tested on a Powerpc box. I am still looking at being able
to test the path, through which allocations happen in non GFP_KERNEL
contexts.
[kamezawa.hiroyu@jp.fujitsu.com: problem with ZONE_MOVABLE] Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Balbir Singh [Thu, 7 Feb 2008 08:14:01 +0000 (00:14 -0800)]
Memory controller: make page_referenced() cgroup aware
Make page_referenced() cgroup aware. Without this patch, page_referenced()
can cause a page to be skipped while reclaiming pages. This patch ensures
that other cgroups do not hold pages in a particular cgroup hostage. It
is required to ensure that shared pages are freed from a cgroup when they
are not actively referenced from the cgroup that brought them in
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Balbir Singh [Thu, 7 Feb 2008 08:13:57 +0000 (00:13 -0800)]
Memory controller improve user interface
Change the interface to use bytes instead of pages. Page sizes can vary
across platforms and configurations. A new strategy routine has been added
to the resource counters infrastructure to format the data as desired.
Suggested by David Rientjes, Andrew Morton and Herbert Poetzl
Tested on a UML setup with the config for memory control enabled.
[kamezawa.hiroyu@jp.fujitsu.com: possible race fix in res_counter] Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com> Signed-off-by: Pavel Emelianov <xemul@openvz.org> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Balbir Singh [Thu, 7 Feb 2008 08:13:56 +0000 (00:13 -0800)]
Memory controller: add per cgroup LRU and reclaim
Add the page_cgroup to the per cgroup LRU. The reclaim algorithm has
been modified to make the isolate_lru_pages() as a pluggable component. The
scan_control data structure now accepts the cgroup on behalf of which
reclaims are carried out. try_to_free_pages() has been extended to become
cgroup aware.
[akpm@linux-foundation.org: fix warning]
[Lee.Schermerhorn@hp.com: initialize all scan_control's isolate_pages member]
[bunk@kernel.org: make do_try_to_free_pages() static]
[hugh@veritas.com: memcgroup: fix try_to_free order]
[kamezawa.hiroyu@jp.fujitsu.com: this unlock_page_cgroup() is unnecessary] Signed-off-by: Pavel Emelianov <xemul@openvz.org> Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Balbir Singh [Thu, 7 Feb 2008 08:13:53 +0000 (00:13 -0800)]
Memory controller: memory accounting
Add the accounting hooks. The accounting is carried out for RSS and Page
Cache (unmapped) pages. There is now a common limit and accounting for both.
The RSS accounting is accounted at page_add_*_rmap() and page_remove_rmap()
time. Page cache is accounted at add_to_page_cache(),
__delete_from_page_cache(). Swap cache is also accounted for.
Each page's page_cgroup is protected with the last bit of the
page_cgroup pointer, this makes handling of race conditions involving
simultaneous mappings of a page easier. A reference count is kept in the
page_cgroup to deal with cases where a page might be unmapped from the RSS
of all tasks, but still lives in the page cache.
Credits go to Vaidyanathan Srinivasan for helping with reference counting work
of the page cgroup. Almost all of the page cache accounting code has help
from Vaidyanathan Srinivasan.
[hugh@veritas.com: fix swapoff breakage]
[akpm@linux-foundation.org: fix locking] Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com> Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com> Cc: Pavel Emelianov <xemul@openvz.org> Cc: Paul Menage <menage@google.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Kirill Korotaev <dev@sw.ru> Cc: Herbert Poetzl <herbert@13thfloor.at> Cc: David Rientjes <rientjes@google.com> Cc: <Valdis.Kletnieks@vt.edu> Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Thu, 7 Feb 2008 08:13:48 +0000 (00:13 -0800)]
memcgroup: temporarily revert swapoff mod
This patch precisely reverts the "swapoff: scan ptes preemptibly" patch
just presented. It's a temporary measure to allow existing memory
controller patches to apply without rejects: in due course they should be
rendered down into one sensible patch, and this reversion disappear.
Paul Menage [Thu, 7 Feb 2008 08:13:45 +0000 (00:13 -0800)]
cgroups: move cgroups destroy() callbacks to cgroup_diput()
Move the calls to the cgroup subsystem destroy() methods from
cgroup_rmdir() to cgroup_diput(). This allows control file reads and
writes to access their subsystem state without having to be concerned with
locking against cgroup destruction - the control file dentry will keep the
cgroup and its subsystem state objects alive until the file is closed.
The documentation is updated to reflect the changed semantics of destroy();
additionally the locking comments for destroy() and some other methods were
clarified and decrustified.
Signed-off-by: Paul Menage <menage@google.com> Cc: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Jackson [Thu, 7 Feb 2008 08:13:44 +0000 (00:13 -0800)]
cgroup simplify space stripping
Simplify the space stripping code in cgroup file write.
[akpm@linux-foundation.org: s/BUG_ON/BUILD_BUG_ON/] Signed-off-by: Paul Jackson <pj@sgi.com> Acked-by: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Jackson [Thu, 7 Feb 2008 08:13:44 +0000 (00:13 -0800)]
cgroup brace coding style fix
Coding style fix - one line conditionals don't get braces.
Signed-off-by: Paul Jackson <pj@sgi.com> Acked-by: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk [Thu, 7 Feb 2008 08:13:43 +0000 (00:13 -0800)]
kernel/cgroup.c: remove dead code
This patch removes dead code spotted by the Coverity checker
(look at the "(nbytes >= PATH_MAX)" check).
Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Paul Jackson <pj@sgi.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Thu, 7 Feb 2008 08:13:42 +0000 (00:13 -0800)]
email-clients.txt: sylpheed is OK at IMAP
This comment is not helpful (no reason given) and is incorrect.
Just stick to facts that are useful regarding working on Linux.
(akpm: I've used sylpheed+imap for years)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Thu, 7 Feb 2008 08:13:42 +0000 (00:13 -0800)]
kernel-doc: warn on badly formatted short description
Make kernel-doc warn when a function/struct/union/typedef does not contain
a properly formatted short description, such as:
* scsi_devinfo: set up the dynamic device list
or
* scsi_devinfo -
This warning is only generated when verbose (-v) mode is used.
Also explain the -v command line option in the -h output.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Thu, 7 Feb 2008 08:13:41 +0000 (00:13 -0800)]
kernel-doc: prevent duplicate description: output
Prevent duplicate output of a Description: section when there is a "blank"
("*") line between the initial function name/description line and the
"Description:" header.
Test case: drivers/scsi/scsi_devinfo.c::scsi_init_devinfo().
Rob Landley hit this while he was producing SCSI kernel-doc.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6 / log