Pavel Emelyanov [Thu, 17 Jul 2008 03:20:58 +0000 (20:20 -0700)]
inet: prepare struct net for TCP MIB accounting
This is the same as the first patch in the set, but preparing
the net for TCP_XXX_STATS - save the struct net on the stack
where required and possible.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Thu, 17 Jul 2008 03:19:08 +0000 (20:19 -0700)]
ipv4: prepare net initialization for IP accounting
Some places, that deal with IP statistics already have where to
get a struct net from, but use it directly, without declaring
a separate variable on the stack.
So, save this net on the stack for future IP_XXX_STATS macros.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Thu, 17 Jul 2008 03:16:14 +0000 (20:16 -0700)]
netdrv intel: always enable VLAN filtering except in promiscous mode
Currently VLAN filtering is enabled when the first VLAN is added.
Obviously before that there's no point in receiving any VLAN packets.
Now that we disable VLAN filtering in promiscous mode, we can keep
the VLAN filters enabled the remaining time.
Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
promiscous mode means to disable *all* filters. Currently only unicast
and multicast filtering is disabled. This patch changes all Intel
drivers to also disable VLAN filtering.
Signed-off-by: Patrick McHardy <kaber@trash.net> Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
ipvs: More reliable synchronization on connection close
This patch enhances the synchronization of the closing connections
between the master and the backup director. It prevents the closed
connections to expire with the 15 min timeout of the ESTABLISHED
state on the backup and makes them expire as they would do on the
master with much shorter timeouts.
Signed-off-by: Rumen G. Bogdanovski <rumen@voicecho.com> Acked-by: Simon Horman <horms@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Sven Wegener [Wed, 16 Jul 2008 11:13:56 +0000 (11:13 +0000)]
ipvs: Put backup thread on mcast socket wait queue
Instead of doing an endless loop with sleeping for one second, we now put the
backup thread onto the mcast socket wait queue and it gets woken up as soon as
we have data to process.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Acked-by: Simon Horman <horms@verge.net.au>
Sven Wegener [Wed, 16 Jul 2008 11:13:50 +0000 (11:13 +0000)]
ipvs: Use kthread_run() instead of doing a double-fork via kernel_thread()
This also moves the setup code out of the daemons, so that we're able to
return proper error codes to user space. The current code will return success
to user space when the daemon is started with an invald mcast interface. With
these changes we get an appropriate "No such device" error.
We longer need our own completion to be sure the daemons are actually running,
because they no longer contain code that can fail and kthread_run() takes care
of the rest.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net> Acked-by: Simon Horman <horms@verge.net.au>
Johannes Berg [Tue, 15 Jul 2008 09:08:24 +0000 (02:08 -0700)]
wireless: fix warnings from QoS patch
When I removed the special "default" meaning from the QoS
parameters, I forgot to update drivers and this lead to
warnings because some drivers were checking for the special
values and putting in defaults. This fixes that by removing
the default special-casing completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Tue, 15 Jul 2008 07:51:45 +0000 (00:51 -0700)]
bluetooth/hci_bcsp: fix bitrev Kconfig
Fix bluetooth hci_bcsp Kconfig to avoid build errors:
drivers/built-in.o: In function `bcsp_prepare_pkt':
hci_bcsp.c:(.text+0x7e9ac): undefined reference to `bitrev16'
drivers/built-in.o: In function `bcsp_recv':
hci_bcsp.c:(.text+0x7f276): undefined reference to `bitrev16'
hci_bcsp.c:(.text+0x7f293): undefined reference to `bitrev16'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Ackey-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net>
net: refactor tcp splice receive path to improve readability
- move all of the details on offsets, lengths and buffers into a
single function instead of doing these operation from multiple places
- use a bottom up approach: try to avoid details in the high level
functions, introduce them gradually as we go deeper in the function
call stack
With helpful feedback from Jarek Poplawski.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com> Acked-by: Jarek Poplawski <jarkao2@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 15 Jul 2008 07:15:08 +0000 (00:15 -0700)]
netdev: Do not use TX lock to protect address lists.
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 15 Jul 2008 07:08:33 +0000 (00:08 -0700)]
netdev: Add addr_list_lock to struct net_device.
This will be used to protect the per-device unicast and multicast
address lists, as well as the callbacks into the drivers which
configure such state such as ->set_rx_mode() and ->set_multicast_list().
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Tue, 15 Jul 2008 06:02:09 +0000 (23:02 -0700)]
icmp: drop unused MIB accounting wrappers
There are ICMP_XXX_STATS that are not used in the kernel, so I remove
them, not to "just patch" them later. But if there's some sense in
keeping them, kick me - I will remake this set keeping them.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Tue, 15 Jul 2008 06:01:40 +0000 (23:01 -0700)]
inet: toss struct net initialization around
Some places, that deal with ICMP statistics already have where
to get a struct net from, but use it directly, without declaring
a separate variable on the stack.
Since I will need this net soon, I declare a struct net on the
stack and use it in the existing places in a separate patch not
to spoil the future ones.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 15 Jul 2008 05:50:15 +0000 (22:50 -0700)]
packet: support extensible, 64 bit clean mmaped ring structure
The tpacket_hdr is not 64 bit clean due to use of an unsigned long
and can't be extended because the following struct sockaddr_ll needs
to be at a fixed offset.
Add support for a version 2 tpacket protocol that removes these
limitations.
Userspace can query the header size through a new getsockopt option
and change the protocol version through a setsockopt option. The
changes needed to switch to the new protocol version are:
1. replace struct tpacket_hdr by struct tpacket2_hdr
2. query header len and save
3. set protocol version to 2
- set up ring as usual
4. for getting the sockaddr_ll, use (void *)hdr + TPACKET_ALIGN(hdrlen)
instead of (void *)hdr + TPACKET_ALIGN(sizeof(struct tpacket_hdr))
Steps 2 and 4 can be omitted if the struct sockaddr_ll isn't needed.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 15 Jul 2008 05:49:30 +0000 (22:49 -0700)]
vlan: deliver packets received with VLAN acceleration to network taps
When VLAN header stripping is used, packets currently bypass packet
sockets (and other network taps) completely. For locally existing
VLANs, they appear directly on the VLAN device, for unknown VLANs
they are silently dropped.
Add a new function netif_nit_deliver() to deliver incoming packets
to all network interface taps and use it in __vlan_hwaccel_rx() to
make VLAN packets visible on the underlying device.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 15 Jul 2008 05:49:06 +0000 (22:49 -0700)]
vlan: Don't store VLAN tag in cb
Use a real skb member to store the skb to avoid clashes with qdiscs,
which are allowed to use the cb area themselves. As currently only real
devices that consume the skb set the NETIF_F_HW_VLAN_TX flag, no explicit
invalidation is neccessary.
The new member fills a hole on 64 bit, the skb layout changes from:
Allan Stephens [Tue, 15 Jul 2008 05:45:33 +0000 (22:45 -0700)]
tipc: Optimization to multicast name lookup algorithm
This patch simplifies and speeds up TIPC's algorithm for identifying
on-node and off-node destinations that overlap a multicast name
sequence range. Rather than traversing the list of all known name
publications within the cluster, it now traverses the (potentially
much shorter) list of name publications made by the node itself, and
determines if any off-node destinations exist by comparing the sizes
of the two lists. (Since the node list must be a subset of the
cluster list, a difference in sizes means that at least one off-node
destination must exist.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 15 Jul 2008 05:44:58 +0000 (22:44 -0700)]
tipc: Add missing locks when inspecting node list & link list
This patch ensures that TIPC configuration commands that display info
about neighboring nodes and their links take the spinlocks that
protect the node list and link lists from changing while the lists
are being traversed.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 15 Jul 2008 05:44:32 +0000 (22:44 -0700)]
tipc: Fix bug in scope checking for multicast messages
This patch ensures that TIPC's multicast message name lookup
algorithm does individualized scope checking for each published
name it examines. Previously, scope checking was only done for
the first name in a name table publication list, which could
result in incoming multicast messages being delivered to ports
publishing names with "node" scope, or not being delivered to
ports publishing names with "cluster" or "zone" scope.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 15 Jul 2008 05:44:01 +0000 (22:44 -0700)]
tipc: Eliminate improper use of TIPC_OK error code
This patch corrects many places where TIPC routines indicated
successful completion by returning TIPC_OK instead of 0.
(The TIPC_OK symbol has the value 0, but it should only be used
in contexts that deal with the error code field of a TIPC
message header.)
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 15 Jul 2008 05:43:32 +0000 (22:43 -0700)]
tipc: Fix race condition that could cause accept() to fail
This patch ensurs that accept() returns successfully even when
the newly created socket is immediately disconnected by its peer.
Previously, accept() would fail if it was unable to pass back
the optional address info for the socket's peer before the
socket became disconnected; TIPC now allows accept() to gather
peer address information after disconnection. As a bonus, the
revised code accesses the socket's port more efficiently, without
the overhead incurred by a reference table lookup.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Tue, 15 Jul 2008 05:42:19 +0000 (22:42 -0700)]
tipc: Remove unneeded parameter to tipc_createport_raw()
This patch eliminates an unneeded parameter when creating a low-level
TIPC port object. Instead of returning both the pointer to the port
structure and the port's reference ID, it now returns only the pointer
since the port structure contains the reference ID as one of its fields.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Li [Tue, 15 Jul 2008 05:39:52 +0000 (22:39 -0700)]
bnx2: Support secondary MAC addresses.
Add support for configuring secondary unicast addresses. There
are 4 additional perfect match filters which can be used for
secondary unicast address support.
* Modified bnx2_set_mac_addr() to be more generic in handling
the setting of the perfect match filters
* Changed bnx2_set_rx_mode() to handle the unicast dev_addr_list
Signed-off-by: Benjamin Li <benli@broadcom.com> Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Tue, 15 Jul 2008 05:39:03 +0000 (22:39 -0700)]
bnx2: Allow flexible VLAN tag settings.
Negotiate with boot code and ASF firmware to see if it can
support keeping VLAN tags in the RX packets. If supported
by firmware, the VLAN tag will be kept in the RX packet
unless VLAN acceleration is registered.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
netlabel: return msg overflow error from netlbl_cipsov4_list faster
Currently, we are trying to place the information from the kernel to
1, 2, 3 and 4 pages sequentially. These pages are allocated via slab.
Though, from the slab point of view steps 3 and 4 are equivalent on
most architectures. So, lets skip 3 pages attempt.
By the way, should we switch from .doit to .dumpit interface here?
The amount of data seems quite big for me.
Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Paul Moore <paul.moore@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
net: Remove references to wan-router.txt in Kconfigs
This patch removes references in drivers/net/wan/Kconfig and
net/wanrouter/Kconfig to Documentation/networking/wan-router.txt
which was removed in commit 99971e70fdc1862e120f3319fc0a4dba8c728acf
("[WANPIPE]: Forgotten bits of Sangoma drivers removal.").
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Max Krasnyansky [Tue, 15 Jul 2008 05:18:19 +0000 (22:18 -0700)]
tun: Fix/rewrite packet filtering logic
Please see the following thread to get some context on this
http://marc.info/?l=linux-netdev&m=121564433018903&w=2
Basically the issue is that current multi-cast filtering stuff in
the TUN/TAP driver is seriously broken.
Original patch went in without proper review and ACK. It was broken and
confusing to start with and subsequent patches broke it completely.
To give you an idea of what's broken here are some of the issues:
- Very confusing comments throughout the code that imply that the
character device is a network interface in its own right, and that packets
are passed between the two nics. Which is completely wrong.
- Wrong set of ioctls is used for setting up filters. They look like
shortcuts for manipulating state of the tun/tap network interface but
in reality manipulate the state of the TX filter.
- ioctls that were originally used for setting address of the the TX filter
got "fixed" and now set the address of the network interface itself. Which
made filter totaly useless.
- Filtering is done too late. Instead of filtering early on, to avoid
unnecessary wakeups, filtering is done in the read() call.
The list goes on and on :)
So the patch cleans all that up. It introduces simple and clean interface for
setting up TX filters (TUNSETTXFILTER + tun_filter spec) and does filtering
before enqueuing the packets.
TX filtering is useful in the scenarios where TAP is part of a bridge, in
which case it gets all broadcast, multicast and potentially other packets when
the bridge is learning. So for example Ethernet tunnelling app may want to
setup TX filters to avoid tunnelling multicast traffic. QEMU and other
hypervisors can push RX filtering that is currently done in the guest into the
host context therefore saving wakeups and unnecessary data transfer.
Signed-off-by: Max Krasnyansky <maxk@qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:59:03 +0000 (20:59 -0700)]
8021q: Check return of dev_set_promiscuity/allmulti
dev_set_promiscuity/allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
Here, we check all positive increment for promiscuity and allmulti
to get error return.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:57:07 +0000 (20:57 -0700)]
macvlan: Check return of dev_set_allmulti
allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
Here, we check the positive increment for allmulti to get error return.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:56:34 +0000 (20:56 -0700)]
ipv4: Fix ipmr unregister device oops
An oops happens during device unregister.
The following oops happened when I add two tunnels, which
use a same device, and then delete one tunnel.
Obviously deleting tunnel "A" causes device unregister, which
send a notification, and after receiving notification, ipmr do
unregister again for tunnel "B" which also use same device.
That is wrong.
After receiving notification, ipmr only needs to decrease reference
count and don't do duplicated unregister.
Fortunately, IPv6 side doesn't add tunnel in ip6mr, so it's clean.
This patch fixs:
- unregister device oops
- using after dev_put()
Wang Chen [Tue, 15 Jul 2008 03:55:26 +0000 (20:55 -0700)]
ipv4: Check return of dev_set_allmulti
allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
Here, we check the positive increment for allmulti to get error return.
PS: For unwinding tunnel creating, we let ipip->ioctl() to handle it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:54:23 +0000 (20:54 -0700)]
ipv6: Check return of dev_set_allmulti
allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
Here, we check the positive increment for allmulti to get error return.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:53:13 +0000 (20:53 -0700)]
bridge: Check return of dev_set_promiscuity
dev_set_promiscuity/allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
Here, we check the positive increment for promiscuity to get error return.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:51:36 +0000 (20:51 -0700)]
bonding: Check return of dev_set_promiscuity/allmulti
dev_set_promiscuity/allmulti might overflow.
Commit: "netdevice: Fix promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
In bond_alb and bond_main, we check all positive increment for promiscuity
and allmulti to get error return.
But there are still two problems left.
1. Some code path has no mechanism to signal errors upstream.
2. If there are multi slaves, it's hard to tell which slaves increment
promisc/allmulti successfully and which failed.
So I left these problems to be FIXME.
Fortunately, the overflow is very rare case.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Tue, 15 Jul 2008 03:49:46 +0000 (20:49 -0700)]
af_packet: Check return of dev_set_promiscuity/allmulti
dev_set_promiscuity/allmulti might overflow. Commit: "netdevice: Fix
promiscuity and allmulti overflow" in net-next makes
dev_set_promiscuity/allmulti return error number if overflow happened.
In af_packet, we check all positive increment for promiscuity and
allmulti to get error return.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Acked-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi: make index unsigned int for iwl_send_led_cmd
This is a small fix to change the idx type from int to unsigned.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Zhu Yi [Fri, 11 Jul 2008 03:53:40 +0000 (11:53 +0800)]
iwlwifi: send TXPOWER command after a new RXON command
The patch fixes the problem that TXPOWER command is not sent
after we issue a new RXON command which requires a tune. Otherwise
we won't be able to Tx any frames.
Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:39 +0000 (11:53 +0800)]
iwlwifi: enable active scanning
This patch enables active scan on active channels.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:38 +0000 (11:53 +0800)]
iwlwifi: unify 4965 and 5000 scanning code
This patch unifies 4965 and 5000 scanning code.
We increases the version number to 1.3.27. Since new uCode
iwlwifi-4965-2.ucode is required for 4965 cards.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:37 +0000 (11:53 +0800)]
iwlwifi: LED use correctly blink table
This patch makes correct usage of the LED blink table.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:36 +0000 (11:53 +0800)]
iwlwifi: fix LED stall
This patch fixes LED stall. last_blink_time was updated only if LED command
was sent, causing wrong computation of the througput.
Some code cleanup comes with this patch as well
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:35 +0000 (11:53 +0800)]
iwlwifi: differentiate 4965 and 5000 hw ampdu queues number
This patch asks to allocate the correct amount of sw queues according
to hw ampdu queues number.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwlwifi: make iwl4965_mac_conf_tx in atomic context
This patch fixes iwl4965_mac_conf_tx. A mutex was taken in atomic context
leading to Oops. This patch removes the mutex and extends the hold
priv->lock. None of the field of QOS is accessed without priv->lock held.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:33 +0000 (11:53 +0800)]
iwlwifi: rs always set lq_sta->priv
This patch fixes printk NULL pointer exceptions in rs code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Guy Cohen <guy.cohen@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 11 Jul 2008 03:53:32 +0000 (11:53 +0800)]
iwlwifi: remove post associate work
This patch removes post associate work. It wasn't used.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the RTS / CTS support in iwlwifi. 5000 will send CTS to
self when allowed by spec, 4965 will send RTS or CTS to self according to
mac80211 request.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Esti Kummer [Fri, 11 Jul 2008 03:53:30 +0000 (11:53 +0800)]
iwlwifi: adding pci device ids to iwl_hw_card_ids
The patch adds PCI device IDs to iwl_hw_card_ids.
Signed-off-by: Esti Kummer <stkumer@localhost.localdomain> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Zhu Yi <yi.zhu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: dont add a STA which is not in the same IBSS
This patch avoids adding STAs that don't belong to our IBSS
ieee80211_bssid_match matches also bcast address so also APs
were added
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 10 Jul 2008 09:22:31 +0000 (11:22 +0200)]
mac80211: fix struct ieee80211_tx_queue_params
Multiple issues:
- there are no "default" values needed
- cw_min/cw_max can be larger than documented
- restructure to decrease size
- use get_unaligned_le16
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 10 Jul 2008 09:21:26 +0000 (11:21 +0200)]
mac80211: fix TX sequence numbers
This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.
This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.
It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 10 Jul 2008 09:16:47 +0000 (11:16 +0200)]
wext: make sysfs bits optional and deprecate them
The /sys/class/net/*/wireless/ direcory is, as far as I know, not
used by anyone. Additionally, the same data is available via wext
ioctls. Hence the sysfs files are pretty much useless. This patch
makes them optional and schedules them for removal.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Jean Tourrilhes <jt@hpl.hp.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the check at the entrance to ieee80211_rx_reorder_ampdu.
This check has been broken by 'mac80211: rx.c use new helpers'.
Letting QoS NULL packet in ieee80211_rx_reorder_ampdu led to packet loss in
RX.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtl8187: use different ANAPARAM*_OFF values for 8187B
For RTL8187B it seems we need special values too for ANAPARAM*_OFF
values (and not use RTL8187 ones). The ANAPARAM*_OFF values used are the
stock ones read from the hardware after a cold boot.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br> Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Wed, 9 Jul 2008 13:48:45 +0000 (15:48 +0200)]
ssb: Include dma-mapping.h
ssb.h implements DMA mapping functions, so it should
include dma-mapping.h. This fixes compile failures on certain architectures.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Wed, 9 Jul 2008 13:12:44 +0000 (15:12 +0200)]
rt2x00: Reorganize beacon handling
With the new beacon handling from mac80211 we can
reorganize the beacon handling in rt2x00 as well.
This patch will move the function to the TX handlers,
and move all duplicate code into rt2x00queue.c.
After this change the descriptor helper functions
from rt2x00queue.c no longer need to be exported
outside of rt2x00lib and can be declared static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 9 Jul 2008 12:40:37 +0000 (14:40 +0200)]
mac80211: revamp beacon configuration
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-2.6 / log