Frej Drejhammar [Mon, 24 Mar 2008 01:43:22 +0000 (22:43 -0300)]
V4L/DVB (7452): cx88: Enable chroma AGC by default for all non-SECAM modes
An enabled chroma AGC will not degrade picture quality if enabled on a
color PAL or NTSC signal with nominal signal levels. It will give a
significant color reproduction improvement if the chroma signals
diverge from nominal levels. Therefore enable chroma AGC by default
for PAL and NTSC standards.
Frej Drejhammar [Mon, 24 Mar 2008 01:43:21 +0000 (22:43 -0300)]
V4L/DVB (7451): cx88: Add user control for chroma AGC
The cx2388x family has support for chroma AGC. This patch implements a
the V4L2_CID_CHROMA_AGC control for the cx2388x family. By default
chroma AGC is disabled, as in previous versions of the driver.
Marton Balint [Wed, 26 Mar 2008 05:07:35 +0000 (02:07 -0300)]
V4L/DVB (7449): cx88: fix oops on module removal caused by IR worker
If the IR worker is not stopped before the removal of the cx88xx module,
an OOPS may occur, because the worker function cx88_ir_work gets called.
So stop the ir worker.
This board has a s5h1409 demod, plus a xc30x8 tuner (probably, xc3018).
This patch adds proper support for radio, video, s-video, composite and ATSC.
However, support for radio and video depends on having s5h1409 i2c gate open,
otherwise, xc30x8 chip won't be visible.
For a better support, some rework is needed on cx88 driver, to allow adding
xc30x8 to i2c bus without sending i2c 0 byte reading to 0xc2 address.
Thanks to Vanessa Ezekowitz <vanessaezekowitz@gmail.com> for helping to figure
out the proper parameters for s5h1409 and the GPIO pins used by each
configuration.
Mike Isely [Sat, 8 Mar 2008 07:02:20 +0000 (04:02 -0300)]
V4L/DVB (7447): pvrusb2: Fix compilation warning
Fix use of a non-int (size_t) being passed in a printf width field.
This benign issue has apparently been around for a long time, but went
undetected until now.
Signed-off-by: Mike Isely <isely@pobox.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Tue, 22 Apr 2008 17:46:25 +0000 (14:46 -0300)]
V4L/DVB (7440): dvb-bt8xx: fix build error
Fix the following build error:
In file included from dvb-bt8xx.c:35:
dvb-bt8xx.h:42:26: error: tuner-simple.h: No such file or directory
dvb-bt8xx.c: In function 'frontend_init':
dvb-bt8xx.c:612: error: 'simple_tuner_attach' undeclared (first use in this function)
dvb-bt8xx.c:612: error: (Each undeclared identifier is reported only once
dvb-bt8xx.c:612: error: for each function it appears in.)
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of '__a'
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:612: warning: cast from pointer to integer of different size
dvb-bt8xx.c:612: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:612: warning: cast from pointer to integer of different size
dvb-bt8xx.c:612: error: called object '__a' is not a function
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of '__a'
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:696: warning: cast from pointer to integer of different size
dvb-bt8xx.c:696: warning: type defaults to 'int' in declaration of 'type name'
dvb-bt8xx.c:696: warning: cast from pointer to integer of different size
dvb-bt8xx.c:696: error: called object '__a' is not a function
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (7439): tuner-xc2028: Adds an option to allow forcing to load an specific firmware name
There are a number of different firmware versions and variants, shipped
together with boards.
This patch adds an extra parameter to the tuner-xc2028 to allow specifying for
an specific firmware name to be loaded. This helps to test for a firmware that
better fits some board.
Michael Krufky [Tue, 22 Apr 2008 17:46:12 +0000 (14:46 -0300)]
V4L/DVB (7407): tuner-simple: add module options to specify rf input
Add module options to tuner-simple, called "atv_input" and "dtv_input"
to specify which rf input to use on devices with multiple rf inputs.
If the module option is not specified, then the driver will autoselect
the rf input, as per previous behavior.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes several kernel oops, when unplugging device while it is in
use:
Basically the patch delays freeing of the internal variables in
si470x_usb_driver_disconnect, until the the last user closed the device in
si470x_fops_release. This was implemented a while ago with the help of Oliver
Neukum.
I tested the patch five times (unplugging while in use) without oops coming
from the radio-si470x driver anymore. A remaining oops was coming from the
usbaudio driver, but this is someone else task. Hopefully this fixed all
unplugging issues.
V4L/DVB (7399): Removes video_dev from tuner-xc2028 config struct
The video_dev parameter, on tuner-xc2028 were used to pass i2c private data to
tuner_callback. Since the driver already have a pointer to i2c_adap->algo_data,
uses this instead.
This parameter were used also as a magic number to idenfity if two drivers are
trying to register the same xc3028 tuner. This occurs with boards with DVB
support, where both DVB and V4L drivers will share the same tuner.
Instead of using the algo_data as a private number, after this patch, the
driver will use i2c_adap->dev, with seems more consistent.
V4L/DVB (7393): tda827x: fixed support of tuners with LNA
Tuner refactoring broke support of tuners with LNA configurations 1 and 2
for both, analog TV and DVB-T.
Additionally, this patch initializes the saa713x gpios defined by the gpiomask
at driver init to avoid undefined stated at dvb.
V4L/DVB (7392): saa7134: support 2nd DVB-S section of the MD8800
There are some restrictions:
- The 2nd DVB-S section will only work if the 1st is configured for DVB-S too.
so "options saa7134-dvb use_frontend=0,1" won't work.
- Currently it is not possible to set the higher LNB supply voltages, so
14V instead of 13V in the 2nd section.
- It is not possibe to turn off the 2nd LNB supply independently.
This comes from the problem that the 2nd section can't access the i2c interface
of the LNB supply chip.
V4L/DVB (7390): saa7134: clear audio DSP interface after access error
In the case of an access error to the high latency registers of
the audio DSP, the interface needs to be cleared, otherwise a cascade
of errors occurs.
This patch is closely modeled after a proposal by Mirek Slugen
drivers/media/video/bt8xx/bttv-cards.c:3030:38: warning: "/*" within comment
drivers/media/video/bt8xx/bttv-cards.c:3032:20: warning: "/*" within comment
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Tue, 22 Apr 2008 17:46:04 +0000 (14:46 -0300)]
V4L/DVB (7379): tuner: prevent instance sharing if i2c adapter is NULL
We currently do not have a method to enable instance staring if i2c adapter
is NULL, in the cases of dvb demods that write to the tuner directly using
calc_regs. Prevent possible wrong instance sharing for these cases until
a better solution can be found.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
flags used for spinlocks don't need to be initialized, except where the
compiler has no way to see, that the spin_unlock_irqrestore is only called
if the spin_lock_irqsave has been called before. Local variable
initialization doesn't have to be protected.
V4L/DVB (7376): Improve compile-time type-checking in videobuf
Make the dev member of the struct videobuf_queue of type "struct device *"
to avoid future problems. Also change the prototype of the
videobuf_queue_core_init() function.
V4L/DVB (7375): cx88/saa7134: fix magic number for xc3028 reusage detection
tuner-xc2028 needs to know when a DVB module is sharing the same analog tuner.
This is done by comparing a magic number that needs to be the same on analog
and on digital. To make easier, this magic number is a pointer to some data
struct.
With the previous code, two different pointers were using, causing a
miss-detection.
It has an audio connector coming out from a chip labeled
ATMEL
0242
AT89C2051-24PI
It is identified as follows on my Debian GNU/Linux Etch (kernel 2.6.18)
...
01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
...
01:0a.0 0400: 109e:036e (rev 11)
Subsystem: 008a:763c
Flags: bus master, medium devsel, latency 64, IRQ 58
Memory at dfffe000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
01:0a.1 0480: 109e:0878 (rev 11)
Subsystem: 008a:763c
Flags: bus master, medium devsel, latency 64, IRQ 58
Memory at dffff000 (32-bit, prefetchable) [size=4K]
Capabilities: [44] Vital Product Data
Capabilities: [4c] Power Management version 2
It was being detected as a GENERIC UNKNOWN CARD both by the 2.6.18
kernel and the latest v4l-dvb drivers, but it did not work at all. The
card has sixteen (16) BNC video inputs, four of them on the board itself
and twelve on three daughter-cards. It has a single bt878 chip, no tuner
and what looks like and audio input. After doing some research I managed
to get only eight channels working by forcing card=125 and those DID NOT
match channels 0-7 on the card, and no audio.
Based on what was working for card=125, I added the card definition
block, added a specific muxsel routine and got the card working fully
with xawtv, where the sixteen channels show up as Composite0 to
Composite15, matching the channel labels in the card and daughter-cards.
I have made no efforts yet to get audio working, but would appreciate
any pointers.
Marcin Slusarz [Tue, 22 Apr 2008 17:45:57 +0000 (14:45 -0300)]
V4L/DVB (7365): reduce stack usage of v4l1_compat_sync
poll_one allocated on stack struct poll_wqueues which is pretty big
structure (>500 bytes on x86_64). v4l1_compat_sync invokes poll_one
in a loop, so allocate struct poll_wqueues in v4l1_compat_sync (with
kmalloc) and pass it to poll_one.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Marcin Slusarz [Tue, 22 Apr 2008 17:45:57 +0000 (14:45 -0300)]
V4L/DVB (7364): reduce stack usage of v4l_compat_translate_ioctl
v4l_compat_translate_ioctl used 1376 bytes of stack (x86_64),
so split this 800 lines long function into ~20 small noinline functions;
the biggest function takes now 712 bytes (v4l1_compat_sync)
fix VIDIOCSWIN handler which printked wrong errors
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Tue, 22 Apr 2008 17:45:56 +0000 (14:45 -0300)]
V4L/DVB (7360): tuner-simple: fix return value of simple_dvb_configure
simple_dvb_configure returns the actual tuned frequency to its caller, so
it must be declared as a u32 rather than an int. As a result, we will
return 0 to indicate a failure.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Tue, 22 Apr 2008 17:45:52 +0000 (14:45 -0300)]
V4L/DVB (7348): tuner-simple: do not send i2c commands if there is no i2c adapter
if (priv->i2c_props.adap == NULL) then exit any function that would
send commands over the i2c bus. We allow drivers to attach without an
i2c adapter for cases where the dvb demod accesses the tuner directly
via calc_regs.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Tue, 22 Apr 2008 17:45:51 +0000 (14:45 -0300)]
V4L/DVB (7346): tda9887: allow multiple driver instances for the same hardware to share state
Convert tda9887 to use the new hybrid_tuner_request_state and
hybrid_tuner_release_state macros to manage state sharing between
hybrid tuner instances.
Some ATSC/DVB cards need to put the analog demodulator into standby
before tuning digital. This patch allows us to attach the tda9887
driver to the digital side of the bridge driver and be able to put
it into standby without jeopardizing the analog demod driver's state.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Tue, 22 Apr 2008 17:45:50 +0000 (14:45 -0300)]
V4L/DVB (7341): ivtv: rename tunerhz to tunertype
There are two tuner types: those for M/N standards and those for all others.
However, M/N standards are not always 60 Hz (PAL-N/Nc are 50 Hz), so rename
the module option accordingly.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
projects / linux-2.6 / log