Stefan Richter [Wed, 18 Jun 2008 16:20:45 +0000 (18:20 +0200)]
firewire: deadline for PHY config transmission
If the low-level driver failed to initialize a card properly without
noticing it, fw-core was blocked indefinitely when trying to send a
PHY config packet. This hung up the events kernel thread, e.g. locked
up keyboard input.
https://bugzilla.redhat.com/show_bug.cgi?id=444694
https://bugzilla.redhat.com/show_bug.cgi?id=446763
This problem was introduced between 2.6.25 and 2.6.26-rc1 by commit 2a0a2590498be7b92e3e76409c9b8ee722e23c8f "firewire: wait until PHY
configuration packet was transmitted (fix bus reset loop)".
The solution is to wait with timeout. I tested it with 7 different
working controllers and 1 non-working controller. On the working ones,
the packet callback complete()s usually --- but not always --- before a
timeout of 10ms. Hence I chose a safer timeout of 100ms.
On the few tests with the non-working controller ALi M5271, PHY config
packet transmission always timed out so far. (Fw-ohci needs to be fixed
for this controller independently of this deadline fix. Often the core
doesn't even attempt to send a phy config because not even self ID
reception works.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sat, 14 Jun 2008 12:23:43 +0000 (14:23 +0200)]
firewire: fw-ohci: unify printk prefixes
The messages which can be enabled by fw-ohci's debug module parameter
are changed from KERN_DEBUG to KERN_NOTICE level and uniformly prefixed
with "firewire_ohci: ". This further simplifies communication with
users when we ask them to capture debug messages.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
and ditto with the other node pointers which fill_bus_reset_event()
accesses. But I went the locked route because one of the two callers
already holds the lock. As a bonus, we don't need the memory barrier
anymore because device->generation and device->node_id are written in
a card->lock protected section.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Thu, 5 Jun 2008 18:50:53 +0000 (20:50 +0200)]
firewire: fw-ohci: write selfIDBufferPtr before LinkControl.rcvSelfID
OHCI 1.1 clause 5.10 requires that selfIDBufferPtr is valid when a 1 is
written into LinkControl.rcvSelfID.
This driver bug has so far not been known to cause harm because most
chips obviously accept a later selfIDBufferPtr write, at least before
HCControl.linkEnable is written.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jarod Wilson <jwilson@redhat.com> Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Stefan Richter [Thu, 5 Jun 2008 18:49:38 +0000 (20:49 +0200)]
firewire: fw-ohci: disable PHY packet reception into AR context
We want the rcvPhyPkt bit in LinkControl off before we start using the
chip. However, the spec says that the reset value of it is undefined.
Hence switch it explicitly off.
https://bugzilla.redhat.com/show_bug.cgi?id=244576#c48 shows that for
example the nForce2 integrated FireWire controller seems to have it on
by default.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jarod Wilson <jwilson@redhat.com>
Stefan Richter [Sat, 31 May 2008 17:36:06 +0000 (19:36 +0200)]
firewire: fw-ohci: use of uninitialized data in AR handler
header_length and payload_length are filled with random data if an
unknown tcode was read from the AR buffer (i.e. if the AR buffer
contained invalid data).
We still need a better strategy to recover from this, but at least
handle_ar_packet now doesn't return out of bound buffer addresses
anymore.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Linus Torvalds [Wed, 18 Jun 2008 00:47:50 +0000 (17:47 -0700)]
x86-64: Fix "bytes left to copy" return value for copy_from_user()
Most users by far do not care about the exact return value (they only
really care about whether the copy succeeded in its entirety or not),
but a few special core routines actually care deeply about exactly how
many bytes were copied from user space.
And the unrolled versions of the x86-64 user copy routines would
sometimes report that it had copied more bytes than it actually had.
Very few uses actually have partial copies to begin with, but to make
this bug even harder to trigger, most x86 CPU's use the "rep string"
instructions for normal user copies, and that version didn't have this
issue.
To make it even harder to hit, the one user of this that really cared
about the return value (and used the uncached version of the copy that
doesn't use the "rep string" instructions) was the generic write
routine, which pre-populated its source, once more hiding the problem by
avoiding the exception case that triggers the bug.
In other words, very special thanks to Bron Gondwana who not only
triggered this, but created a test-program to show it, and bisected the
behavior down to commit 08291429cfa6258c4cd95d8833beb40f828b194e ("mm:
fix pagecache write deadlocks") which changed the access pattern just
enough that you can now trigger it with 'writev()' with multiple
iovec's.
That commit itself was not the cause of the bug, it just allowed all the
stars to align just right that you could trigger the problem.
[ Side note: this is just the minimal fix to make the copy routines
(with __copy_from_user_inatomic_nocache as the particular version that
was involved in showing this) have the right return values.
We really should improve on the exceptional case further - to make the
copy do a byte-accurate copy up to the exact page limit that causes it
to fail. As it is, the callers have to do extra work to handle the
limit case gracefully. ]
Reported-by: Bron Gondwana <brong@fastmail.fm> Cc: Nick Piggin <npiggin@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andi Kleen <andi@firstfloor.org> Cc: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(which didn't have this problem), and since
most users that do the carethis was very hard to trigger, but
Linus Torvalds [Mon, 16 Jun 2008 20:17:33 +0000 (13:17 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2:
ocfs2: Remove ->hangup() from stack glue operations.
ocfs2: Move the call of ocfs2_hb_ctl into the stack glue.
ocfs2: Move the hb_ctl_path sysctl into the stack glue.
Joel Becker [Fri, 30 May 2008 22:58:26 +0000 (15:58 -0700)]
ocfs2: Remove ->hangup() from stack glue operations.
The ->hangup() call was only used to execute ocfs2_hb_ctl. Now that
the generic stack glue code handles this, the underlying stack drivers
don't need to know about it.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 30 May 2008 22:43:58 +0000 (15:43 -0700)]
ocfs2: Move the call of ocfs2_hb_ctl into the stack glue.
Take o2hb_stop() out of the o2cb code and make it part of the generic
stack glue as ocfs2_leave_group(). This also allows us to remove the
ocfs2_get_hb_ctl_path() function - everything to do with hb_ctl is now
part of stackglue.c. o2cb no longer needs a ->hangup() function.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Joel Becker [Fri, 30 May 2008 22:30:49 +0000 (15:30 -0700)]
ocfs2: Move the hb_ctl_path sysctl into the stack glue.
ocfs2 needs to call out to the hb_ctl program at unmount for all cluster
stacks. The first step is to move the hb_ctl_path sysctl out of the
o2cb code and into the generic stack glue.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Linus Torvalds [Mon, 16 Jun 2008 17:24:01 +0000 (10:24 -0700)]
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (21 commits)
[POWERPC] Turn on ATA_SFF so we get SATA_SVW back in defconfigs
[POWERPC] Remove ppc32's export of console_drivers
[POWERPC] Fix -Os kernel builds with newer gcc versions
[POWERPC] Fix bootwrapper builds with newer gcc versions
[POWERPC] Build fix for drivers/macintosh/mediabay.c
[POWERPC] Fix warning in pseries/eeh_driver.c
[POWERPC] Add missing of_node_put in drivers/macintosh/therm_adt746x.c
[POWERPC] Add missing of_node_put in drivers/macintosh/smu.c
[POWERPC] Add missing of_node_put in pseries/nvram.c
[POWERPC] Fix return value check logic in debugfs virq_mapping setup
[POWERPC] Fix rmb to order cacheable vs. noncacheable
powerpc/spufs: fix missed stop-and-signal event
powerpc/spufs: synchronize interaction between spu exception handling and time slicing
powerpc/spufs: remove class_0_dsisr from spu exception handling
powerpc/spufs: wait for stable spu status in spu_stopped()
[POWERPC] bootwrapper: add simpleImage* to list of boot targets
[POWERPC] 83xx: MPC837xRDB's VSC7385 ethernet switch isn't on the MDIO bus
[POWERPC] Updated Freescale PPC defconfigs
[POWERPC] 8610: Update defconfig for MPC8610 HPCD
[POWERPC] 85xx: MPC8548CDS - Fix size of PCIe IO space
...
Linus Torvalds [Mon, 16 Jun 2008 17:22:31 +0000 (10:22 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Au1200: MMC resource size off by one
[MIPS] TANBAC: Update defconfig
[MIPS] Vr41xx: Initialize PCI io_map_base
[MIPS] Malta: Always compile MTD platform device registration code.
[MIPS] Malta: Fix build errors for 64-bit kernels
[MIPS] Lasat: sysctl fixup
[MIPS] Fix buggy use of kmap_coherent.
[MIPS] Lasat: bring back from the dead
[MIPS] vpe_id is required for VSMP and SMTC builds
[MIPS] Export smp_call_function and smp_call_function_single.
[MIPS] Bring the SWARM defconfig up to date
[MIPS] Sibyte: Build RTC support as an object
[MIPS] Fix the fix for divide by zero error in build_{clear,copy}_page
[MIPS] Fix build for PNX platforms.
[MIPS] Add RM200 with R5000 CPU to known ARC machines
[MIPS] Better load address for big endian SNI RM
[MIPS] SB1250: Initialize io_map_base
[MIPS] Alchemy: Add au1500 reserved interrupt
[MIPS] Export empty_zero_page for sake of the ext4 module.
David Woodhouse [Mon, 16 Jun 2008 11:24:17 +0000 (12:24 +0100)]
Export <linux/a.out.h> to userspace again.
This seems to have been removed accidentally in commit ed7b1889da256977574663689b598d88950bbd23 ("Unexport asm/page.h"), but
wasn't supposed to have been -- the original patch at
http://lkml.org/lkml/2007/10/30/144 just moved it from $(header-y) to
$(unifdef-y)
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Woodhouse [Mon, 16 Jun 2008 11:18:24 +0000 (12:18 +0100)]
Remove #ifdef CONFIG_ARCH_SUPPORTS_AOUT from <linux/a.out.h>
This file is only included where it makes sense now, so there's no need
for the CONFIG_ARCH_SUPPORTS_AOUT conditional -- and that conditional is
bad, because we want to export <linux/a.out.h> to userspace.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Woodhouse [Mon, 16 Jun 2008 11:18:13 +0000 (12:18 +0100)]
Remove last traces of a.out support from ELF loader.
In commit d20894a23708c2af75966534f8e4dedb46d48db2 ("Remove a.out
interpreter support in ELF loader"), Andi removed support for a.out
interpreters from the ELF loader, which was only ever needed for the
transition from a.out to ELF.
This removes the last traces of that support, in particular the
inclusion of <linux/a.out.h>.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Woodhouse [Mon, 16 Jun 2008 11:11:54 +0000 (12:11 +0100)]
Include <asm/a.out.h> in fs/exec.c only for Alpha.
We only need it for the /sbin/loader hack for OSF/1 executables, and we
don't want to include it otherwise.
While we're at it, remove the redundant '&& CONFIG_ARCH_SUPPORTS_AOUT'
in the ifdef around that code. It's already dependent on __alpha__, and
CONFIG_ARCH_SUPPORTS_AOUT is hard-coded to 'y' there.
Signed-off-by: David Woodhouse <dwmw2@infradead.org> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sergei Shtylyov [Thu, 8 May 2008 19:06:17 +0000 (23:06 +0400)]
[MIPS] Au1200: MMC resource size off by one
Au12x0 MMC platform device strangely claims 0x41 bytes for its
memory-mapped registers. Make it claim the whole 0x80000 instead according
to the memory map given in the datasheets.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thomas Horsten [Sun, 15 Jun 2008 01:17:11 +0000 (02:17 +0100)]
[MIPS] Lasat: sysctl fixup
LASAT's sysctl interface was broken, it failed a check during boot because
a single entry had a sysctl number and the rest were unnumbered. When I
fixed it I noticed that the whole sysctl file needed a spring clean, it was
using mutexes where it wasn't needed (it's only needed to protect during
writes to the EEPROM), so I moved that stuff out and generally cleaned the
whole thing up.
So now, LASAT's sysctl/proc interface is working again.
Signed-off-by: Thomas Horsten <thomas@horsten.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Sat, 14 Jun 2008 21:22:08 +0000 (22:22 +0100)]
[MIPS] Fix buggy use of kmap_coherent.
Assuming the call of kmap_coherent in local_r4k_flush_cache_page doesn't
need fixing this was skipped in fcae549295bcae801ac48fc1c2030ab8cc487020.
Turns out it needed the same change after all.
Thomas Horsten [Sat, 14 Jun 2008 01:32:42 +0000 (02:32 +0100)]
[MIPS] Lasat: bring back from the dead
After the common MIPS CPU interrupt controller (for irq0-7) was introduced
the Lasat boards didn't get their interrupts right, so nothing worked. The
old routines need to be offset by the new 8 hardware interrupts common to
all MIPS CPU's.
Signed-off-by: Thomas Horsten <thomas@horsten.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SWARM defconfig file has not been regenerated for over a year now.
Here is a patch to bring the file up to date. Additionally some important
and sometimes confusing changes happened meanwhile. Here is the list of
notable corresponding updates to the configuration:
1. CPU_SB1_PASS_2_2 is now selected rather than CPU_SB1_PASS_1. The
latter requires a non-standard -msb1-pass1-workarounds option to be
supported by GCC and I am told is quite rare anyway.
[Ralf: Afaik -msb1-pass1-workarounds is available only in Monta Vista's
special Sibyte gcc 3.0 variant and gcc 3.0 is too old to build a modern
kernel anyway.]
2. PHYLIB and BROADCOM_PHY are both built in and NETDEV_1000 enabled as
required by SB1250_MAC.
3. USB and USB_OHCI_HCD are enabled as there is an OHCI chip onboard.
4. TMPFS is enabled, because I use it. ;-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Build the SWARM platform library is as an object rather than an archive
so that files which only contain symbols used by initcalls and do not
provide any symbols that would pull them from an archive still work.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Mackerras [Mon, 16 Jun 2008 11:14:12 +0000 (21:14 +1000)]
[POWERPC] Turn on ATA_SFF so we get SATA_SVW back in defconfigs
This enables CONFIG_ATA_SFF in the defconfigs that are intended to
work on a G5 powermac, i.e. g5_defconfig and ppc64_defconfig. Since
the support for the SATA cell in the K2 chipset is provided by the
sata_svw.c driver, and that depends on CONFIG_ATA_SFF, we need to turn
that and CONFIG_SATA_SVW back on so we can get to the hard disk on G5s.
This breaks the kernel if we enable CONFIG_CC_OPTIMIZE_FOR_SIZE. To fix
this we add the use the save/restore code from gcc and simplified it down
for our needs (integer only).
Additionally, we have to link this code into each module. The other
solution was to add EXPORT_SYMBOL() which meant going through the
trampoline which seemed nonsensical for these out-of-line routines.
Finally, we add some checks to prom_init_check.sh to ignore the
out-of-line save/restore functions.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Adrian Bunk [Tue, 10 Jun 2008 17:47:45 +0000 (03:47 +1000)]
[POWERPC] Build fix for drivers/macintosh/mediabay.c
This fixes the following build error with CONFIG_BLK_DEV_IDE_PMAC=n:
<-- snip -->
...
CC drivers/macintosh/mediabay.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/macintosh/mediabay.c: In function 'check_media_bay':
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/macintosh/mediabay.c:428: error: 'struct media_bay_info' has no member named 'cd_index'
make[3]: *** [drivers/macintosh/mediabay.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andrew Morton [Mon, 9 Jun 2008 23:26:10 +0000 (09:26 +1000)]
[POWERPC] Fix warning in pseries/eeh_driver.c
Fix this:
/usr/src/devel/arch/powerpc/platforms/pseries/eeh_driver.c: In function 'print_device_node_tree':
/usr/src/devel/arch/powerpc/platforms/pseries/eeh_driver.c:55: warning: ISO C90 forbids mixed declarations and code
also make that function look like it's part of Linux.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
n = of_find_node_by_name(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f(n,...)
when != E = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n1 = f(n,...)
|
E = n
|
return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
n = of_find_node_by_type(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f1(n,...)
when != E1 = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n2 = f2(n,...)
|
E2 = n
|
return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
n = of_find_node_by_type(...)
...
if (!n) S
... when != of_node_put(n)
when != n1 = f1(n,...)
when != E1 = n
when any
when strict
(
+ of_node_put(n);
return -C;
|
of_node_put(n);
|
n2 = f2(n,...)
|
E2 = n
|
return ...;
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Emil Medve [Thu, 22 May 2008 19:49:22 +0000 (05:49 +1000)]
[POWERPC] Fix return value check logic in debugfs virq_mapping setup
debugfs_create_file() returns a non-NULL (non-zero) value in case of
success, not a NULL value.
This fixes this non-critical boot-time debugging error message:
[ 1.316386] calling irq_debugfs_init+0x0/0x50
[ 1.316399] initcall irq_debugfs_init+0x0/0x50 returned -12 after 0 msecs
[ 1.316411] initcall irq_debugfs_init+0x0/0x50 returned with error code -12
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com> Acked-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Nick Piggin [Wed, 21 May 2008 14:10:56 +0000 (00:10 +1000)]
[POWERPC] Fix rmb to order cacheable vs. noncacheable
lwsync is explicitly defined not to have any effect on the ordering of
accesses to device memory, so it cannot be used for rmb(). sync appears
to be the only barrier which fits the bill.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Luke Browning [Mon, 16 Jun 2008 00:42:38 +0000 (10:42 +1000)]
powerpc/spufs: fix missed stop-and-signal event
There is a delay in the transition to the stopped state for class 2
interrupts. In some cases, the controlling thread detects the state of
the spu as running, and goes back to sleep resulting in a hung
application as the event is missed.
This change detects the stop condition and re-generates the wakeup event
after a context save.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Luke Browning [Fri, 13 Jun 2008 04:17:35 +0000 (14:17 +1000)]
powerpc/spufs: synchronize interaction between spu exception handling and time slicing
Time slicing can occur at the same time as spu exception handling
resulting in the wakeup of the wrong thread.
This change uses the the spu's register_lock to enforce synchronization
between bind/unbind and spu exception handling so that they are
mutually exclusive.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Luke Browning [Thu, 5 Jun 2008 09:30:25 +0000 (17:30 +0800)]
powerpc/spufs: remove class_0_dsisr from spu exception handling
According to the CBEA, the SPU dsisr is not updated for class 0
exceptions.
spu_stopped() is testing the dsisr that was passed to it from the class
0 exception handler, so we return a false positive here.
This patch cleans up the interrupt handler and erroneous tests in
spu_stopped. It also removes the fields from the csa since it is not
needed to process class 0 events.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide-generic: don't probe all legacy ISA IDE ports by default
ide-cs: fix releasing I/O resources
ide-cs: fix probing and add warm-plug support
ide-pmac: remove bogus comment about pmac_ide_setup_device()
ide-pmac: add ->cable_detect method
ide-pmac: bugfix for media-bay support rework
opti621: add PIO 4 support
opti621: use pre-calculated PIO timings
opti621: program devices timings separately in ->set_pio_mode
opti621: use PCI clock value provided by controller
opti621: remove DMA support
opti621: disable read prefetch
ide-generic: don't probe all legacy ISA IDE ports by default
We can't probe all legacy ISA IDE ports by default as the resources may be
occupied by other ISA devices. Add "probe_mask" module parameter and probe
only first two ISA IDE ports by default leaving the decision about probing
the rest to the user (systems with ISA ide2-6 should be very, very rare).
Reported-by: Mikael Pettersson <mikpe@it.uu.se> Bisected-by: Mikael Pettersson <mikpe@it.uu.se> Tested-by: Mikael Pettersson <mikpe@it.uu.se> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Linus Torvalds [Sat, 14 Jun 2008 20:32:56 +0000 (13:32 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: fixup write combine comment in pci_mmap_resource
x86: PAT export resource_wc in pci sysfs
x86, pci-dma.c: don't always add __GFP_NORETRY to gfp
suspend-vs-iommu: prevent suspend if we could not resume
x86: pci-dma.c: use __GFP_NO_OOM instead of __GFP_NORETRY
pci, x86: add workaround for bug in ASUS A7V600 BIOS (rev 1005)
PCI: use dev_to_node in pci_call_probe
PCI: Correct last two HP entries in the bfsort whitelist
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: update my email address
parisc: fix miscompilation of ip_fast_csum with gcc >= 4.3
parisc: fix off by one in setup_sigcontext32
parisc: export empty_zero_page
parisc: export copy_user_page_asm
parisc: move head.S to head.text section
Revert "parisc: fix trivial section name warnings"
Linus Torvalds [Fri, 13 Jun 2008 14:40:57 +0000 (07:40 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: Workaround HW bug for SB600/700 SATA controller PMP support
ahci: workarounds for mcp65
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
tcp: Revert 'process defer accept as established' changes.
ipv6: Fix duplicate initialization of rawv6_prot.destroy
bnx2x: Updating the Maintainer
net: Eliminate flush_scheduled_work() calls while RTNL is held.
drivers/net/r6040.c: correct bad use of round_jiffies()
fec_mpc52xx: MPC52xx_MESSAGES_DEFAULT: 2nd NETIF_MSG_IFDOWN => IFUP
ipg: fix receivemode IPG_RM_RECEIVEMULTICAST{,HASH} in ipg_nic_set_multicast_list()
netfilter: nf_conntrack: fix ctnetlink related crash in nf_nat_setup_info()
netfilter: Make nflog quiet when no one listen in userspace.
ipv6: Fail with appropriate error code when setting not-applicable sockopt.
ipv6: Check IPV6_MULTICAST_LOOP option value.
ipv6: Check the hop limit setting in ancillary data.
ipv6 route: Fix route lifetime in netlink message.
ipv6 mcast: Check address family of gf_group in getsockopt(MS_FILTER).
dccp: Bug in initial acknowledgment number assignment
dccp ccid-3: X truncated due to type conversion
dccp ccid-3: TFRC reverse-lookup Bug-Fix
dccp ccid-2: Bug-Fix - Ack Vectors need to be ignored on request sockets
dccp: Fix sparse warnings
dccp ccid-3: Bug-Fix - Zero RTT is possible
Tejun Heo [Mon, 9 Jun 2008 15:13:04 +0000 (00:13 +0900)]
ahci: workarounds for mcp65
MCP65 ahci can do NCQ but doesn't set the CAP bit and rev A0 and A1
can't do MSI but have MSI capability. Implement AHCI_HFLAG_YES_NCQ
and apply appropriate workarounds.
Sergey Lapin [Thu, 12 Jun 2008 22:21:55 +0000 (15:21 -0700)]
rtc: Ramtron FM3130 RTC support
Ramtron FM3130 is a chip with two separate devices inside, RTC clock and
FRAM. This driver provides only RTC functionality.
This chip is met in lots of custom boards with AT91SAMXXXX CPU I work
with, is cheap and in no way better or worse than any other RTC on market.
While it is mostly met on much smaller devices, I think it is great to
have it supported in Linux.
Signed-off-by: Sergey Lapin <slapin@ossfans.org> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Brownell [Thu, 12 Jun 2008 22:21:55 +0000 (15:21 -0700)]
rtc: make HPET_RTC_IRQ track HPET_EMULATE_RTC
More Kconfig tweaks related to the legacy PC RTC code:
- Describe the legacy PC RTC driver as such ... it's never quite
been clear that this driver is for PC RTCs, and now it's fair
to call this the "legacy" driver.
- Force it to understand about HPET stealing its IRQs ... kernel
code does this always when HPET is in use, there should be no
option for users to goof up the config.
This seems to fix kernel bugzilla #10729.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Maxim Levitsky <maximlevitsky@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stas Sergeev [Thu, 12 Jun 2008 22:21:54 +0000 (15:21 -0700)]
provide rtc_cmos platform device
Recently (around 2.6.25) I've noticed that RTC no longer works for me. It
turned out this is because I use pnpacpi=off kernel option to work around
the parport_pc bugs. I always did so, but RTC used to work fine in the
past, and now it have regressed.
The patch fixes the problem by creating the platform device for the RTC
when PNP is disabled. This may also help running the PNP-enabled kernel
on an older PCs.
Signed-off-by: Stas Sergeev <stsp@aknet.ru> Cc: David Brownell <david-b@pacbell.net> Cc: Ingo Molnar <mingo@elte.hu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Bjorn Helgaas <bjorn.helgaas@hp.com> Cc: Adam Belay <ambx1@neo.rr.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Thu, 12 Jun 2008 22:21:52 +0000 (15:21 -0700)]
radix-tree: fix small lockless radix-tree bug
We shrink a radix tree when its root node has only one child, in the left
most slot. The child becomes the new root node. To perform this
operation in a manner compatible with concurrent lockless lookups, we
atomically switch the root pointer from the parent to its child.
However a concurrent lockless lookup may now have loaded a pointer to the
parent (and is presently deciding what to do next). For this reason, we
also have to keep the parent node in a valid state after shrinking the
tree, until the next RCU grace period -- otherwise this lookup with the
parent pointer may not do the right thing. Notably, we need to keep the
child in the left most slot there in case that is requested by the lookup.
This is all pretty standard RCU stuff. It is worth repeating because in
my eagerness to obey the radix tree node constructor scheme, I had broken
it by zeroing the radix tree node before the grace period.
What could happen is that a lookup can load the parent pointer, then
decide it wants to follow the left most child slot, only to find the slot
contained NULL due to the concurrent shrinker having zeroed the parent
node before waiting for a grace period. The lookup would return a false
negative as a result.
Fix it by doing that clearing in the RCU callback. I would normally want
to rip out the constructor entirely, but radix tree nodes are one of those
places where they make sense (only few cachelines will be touched soon
after allocation).
This was never actually found in any lockless pagecache testing or by the
test harness, but by seeing the odd problem with my scalable vmap rewrite.
I have not tickled the test harness into reproducing it yet, but I'll
keep working at it.
Fortunately, it is not a problem anywhere lockless pagecache is used in
mainline kernels (pagecache probe is not a guarantee, and brd does not
have concurrent lookups and deletes).
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
because that changeset made k_self consider the value as a latin1
character when in Unicode mode, which is wrong; k_self should still take
the console map into account.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6 / log