Li Yang [Mon, 23 Apr 2007 17:38:18 +0000 (10:38 -0700)]
USB: update MAINAINERS and CREDITS for Freescale USB driver
Add MAINAINERS and CREDITS entry for Freescale Highspeed USB device
driver.
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Li Yang [Mon, 23 Apr 2007 17:37:36 +0000 (10:37 -0700)]
USB: update gadget files for fsl_usb2_udc driver
Update gadget_chip.c, ether.c for newly added Freescale Highspeed USB
device driver.
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Li Yang [Mon, 23 Apr 2007 17:54:25 +0000 (10:54 -0700)]
USB: add Freescale high-speed USB SOC device controller driver
Freescale high-speed USB SOC can be found on some Freescale processors
among different architectures. It supports both host and device functions.
This driver adds its device support for Linux USB Gadget layer.
It is tested on MPC8349 and MPC8313, but should work on other platforms
with minor tweaks. The driver passed USBCV 1.3 compliance tests. Note
that this driver doesn't yet include OTG support.
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Jiang Bo <tanya.jiang@freescale.com> Signed-off-by: Bruce Schmid <duck@freescale.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: iowarrior.c: timeouts too small in usb_control_msg calls
The driver uses usb_control_msg() for exchanging data with the device.
When the driver lived freeley _outside_ the kernel tree (pre 2.6.21) the
timeouts for these calls where set to 5*HZ for reading, 1HZ for writing.
(These timeouts seemed to work fine for all users of the driver, at
least nobody complained in the last 2 years.
The current code (2.6.21-rc5) removed the 'HZ' from the timeouts and
left the driver with 5 jiffies for reading and 1 jiffy for writing. My
new machine is fast, but not that fast.
The patch also removes a useless debug statement, which was left over
from testing a broken firmware version
Phil Dibowitz [Mon, 16 Apr 2007 06:42:40 +0000 (23:42 -0700)]
USB: Remove Huawei unusual_devs entry
Per the Rui Santos and the hardware manufacturers, this actually inhibits
useful parts of the hardware. The correct way to use this hardware is with the
software at http://www.kanoistika.sk/bobovsky/archiv/umts/ and the manufacturers
are also planning on including Linux drivers/material in future revisions.
I have found that /drivers/usb/misc/ldusb.c works with the "PICDEM Full
Speed USB"
http://www.microchip.com/stellent/idcplg?IdcService=SS_GET_PAGE&nodeId=1406&dDocName=en021940
Signed-off-by: Joey S Goncalves <jgoncalves@peragrin.com> Cc: Michael Hund <MHund@LD-Didactic.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sun, 22 Apr 2007 18:05:52 +0000 (11:05 -0700)]
USB: remove ancient/broken CRIS hcd
Remove the old crisv10 HCD ... it can't have built for some time,
doesn't even have a Kconfig entry, was the last driver not to have
been converted to the "hcd" framework, and considering the usbcore
changes since its last patch was merged, has just got to buggy as
all get-out.
I'm told Axis has a new driver, and will be submitting it soon.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: Mikael Starvik <mikael.starvik@axis.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Erik Hovland [Mon, 23 Apr 2007 17:50:15 +0000 (10:50 -0700)]
usb ethernet gadget, workaround network stack API glitch
Another workaround for the glitch in the network layer, whereby one call
ignores the (otherwise kernel-wide) convention that free() calls should
not oops when passed nulls. This code already handles that API glitch in
most other paths.
From: Erik Hovland <erik@hovland.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simon Arlott [Thu, 26 Apr 2007 07:38:05 +0000 (00:38 -0700)]
USB: cxacru: ADSL state management
The device has commands to start/stop the ADSL function, so this adds a
sysfs attribute to allow it to be started/stopped/restarted. It also stops
polling the device for status when the ADSL function is disabled.
There are no problems with sending multiple start or stop commands, even
with a fast loop of them the device still works. There is no need to
protect the restart process from further user actions while it's waiting
for 1.5s.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: Duncan Sands <duncan.sands@math.u-psud.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simon Arlott [Thu, 26 Apr 2007 07:38:04 +0000 (00:38 -0700)]
usbatm: Detect usb device shutdown and ignore failed urbs
Detect usb device shutdown and ignore failed urbs. This happens when the
driver is unloaded or the device is unplugged.
I'm not sure what other urb statuses should be ignored, and the warning
message doesn't need to be shown when the module is unloaded or the device
is removed.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: Duncan Sands <duncan.sands@math.u-psud.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Leon Leong [Thu, 26 Apr 2007 07:38:02 +0000 (00:38 -0700)]
USB: BandRich BandLuxe HSDPA Data Card Driver
Add the detection for the BandRich BandLuxe C100/C100S/C120 HSDPA Data
Card. With the vendor and product IDs are set properly, the data card can
be detected and works fine.
Signed-off-by: Leon Leong <upleong@bandrich.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 17 Apr 2007 20:06:29 +0000 (13:06 -0700)]
USB: add an ohci board-specific quirk
Use the new ohci-pci quirk infrastructure to address the problem it was
created to address: a quirk specific to the Portege 4000, in buzilla as
http://bugzilla.kernel.org/show_bug.cgi?id=6723
Also fix a misuse of "__devinit" for the quirk functions. It must not
be used without first ensuring that the references from the quirk tables
are gone, and that the function using those quirk tables is also gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 17 Apr 2007 23:10:10 +0000 (16:10 -0700)]
USB: usbnet reports minidriver name through ethtool
Update "usbnet" so that ethtool reports the name of the minidriver in use
(e.g. asix, cdc_ether, dm9601, rndis_host) instead of "usbnet". This is a
better match to how other network drivers work, resolving a minor open issue.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Wed, 18 Apr 2007 00:53:20 +0000 (17:53 -0700)]
USB: rndis_host, various cleanups
Cleanups to the rndis_host code, and a tweak that helps talking to
PXA hardware. Mostly from Ole André Vadla Ravnås <oleavr@gmail.com>
- Prevent SET_INTERFACE requests, they give PXA hardware bad indigestion
- For paranoia, null a pointer after freeing its data
- Wrap up ActiveSync oddities for RNDIS_QUERY in one routine
- Use that wrapper when getting the Ethernet address
- Whitespace fixes
Plus add a comment noting the open issues about some RNDIS clients still
needing TBD kinds of browbeating to accept non-jumbogram packets.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Wed, 11 Apr 2007 20:47:26 +0000 (13:47 -0700)]
usbmon: bus zero
Add the "bus zero" feature to the usbmon. If a user process specifies bus
with number zero, it receives events from all buses. This is useful when
we wish to see initial enumeration when a bus is created, typically after
a modprobe. Until now, an application had to loop until a new bus could
be open, then start capturing on it. This procedure was cumbersome and
could lose initial events. Also, often it's too bothersome to find exactly
to which bus a specific device is attached.
Paolo Albeni provided the original concept implementation. I added the
handling of "bus->monitored" flag and generally fixed it up.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Tony Lindgren [Sun, 1 Apr 2007 01:15:43 +0000 (18:15 -0700)]
USB: Allow transfer_buffer with transfer_dma
Some host controller drivers may need a PIO fallback when a DMA channel
is temporarily unavailable. This patch provides an address that such
drivers can use for PIO in those cases, and nulls that field out when
no such address is available (highmem) which should help usbmon.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 27 Mar 2007 17:33:59 +0000 (13:33 -0400)]
USB: add "last_busy" field for use in autosuspend
This patch (as877) adds a "last_busy" field to struct usb_device, for
use by the autosuspend framework. Now if an autosuspend call comes at
a time when the device isn't busy but hasn't yet been idle for long
enough, the timer can be set to exactly the desired value. And we
will be ready to handle things like HID drivers, which can't maintain
a useful usage count and must rely on the time-of-last-use to decide
when to autosuspend.
The patch also makes some related minor improvements:
Move the calls to the autosuspend condition-checking routine
into usb_suspend_both(), which is the only place where it
really matters.
If the autosuspend timer is already running, don't stop
and restart it.
Replace immediate returns with gotos so that the optional
debugging ouput won't be bypassed.
If autoresume is disabled but the device is already awake,
don't return an error for an autoresume call.
Don't try to autoresume a device if it isn't suspended.
(Yes, this undercuts the previous change -- so sue me.)
Don't duplicate existing code in the autosuspend work routine.
Fix the kerneldoc in usb_autopm_put_interface(): If an
autoresume call fails, the usage counter is left unchanged.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 27 Mar 2007 14:02:34 +0000 (16:02 +0200)]
USB: fix omninet write vs. close race
omninet kills all URBs in close. However write() returns as soon as
the URB has been submitted. Killing the last URB means a race that
can lose that date written in the last call to write().
As a fix this is moved to shutdown().
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Fri, 30 Mar 2007 11:11:00 +0000 (13:11 +0200)]
USB: fix catc error handling
this driver ignores errors while starting the transmit queue. It will
never be reported stopped as the completion handler won't run
and it will never be started again as it will be considered started.
This patch adds error handling.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jelle Foks [Mon, 26 Mar 2007 01:08:35 +0000 (21:08 -0400)]
USB: ftdi_sio: Add USB ID of ADSTech USBX-707
This patch adds the USB ID of the ADS Tech USBX-707 USB IR blaster (that
comes with the ADS Tech PTV-305 grabber card), which has a ftdi232bm
inside hooked up to a pic.
With this it should be fairly straightforward to make at least lirc
receiving work with this device. I will submit a patch to lirc for that
as soon as I have one ready, I'm getting data with minicom with this
patch, but need to figure out some more details such as best/correct
baudrate.
Kay Sievers [Tue, 13 Mar 2007 14:59:31 +0000 (15:59 +0100)]
USB: make usbdevices export their device nodes instead of using a separate class
o The "real" usb-devices export now a device node which can
populate /dev/bus/usb.
o The usb_device class is optional now and can be disabled in the
kernel config. Major/minor of the "real" devices and class devices
are the same.
o The environment of the usb-device event contains DEVNUM and BUSNUM to
help udev and get rid of the ugly udev rule we need for the class
devices.
o The usb-devices and usb-interfaces share the same bus, so I used
the new "struct device_type" to let these devices identify
themselves. This also removes the current logic of using a magic
platform-pointer.
The name of the device_type is also added to the environment
which makes it easier to distinguish the different kinds of devices
on the same subsystem.
It looks like this:
add@/devices/pci0000:00/0000:00:1d.1/usb2/2-1
ACTION=add
DEVPATH=/devices/pci0000:00/0000:00:1d.1/usb2/2-1
SUBSYSTEM=usb
SEQNUM=1533
MAJOR=189
MINOR=131
DEVTYPE=usb_device
PRODUCT=46d/c03e/2000
TYPE=0/0/0
BUSNUM=002
DEVNUM=004
This udev rule works as a replacement for usb_device class devices:
SUBSYSTEM=="usb", ACTION=="add", ENV{DEVTYPE}=="usb_device", \
NAME="bus/usb/$env{BUSNUM}/$env{DEVNUM}", MODE="0644"
Updated patch, which needs the device_type patches in Greg's tree.
I also got a bugzilla assigned for this. :)
https://bugzilla.novell.com/show_bug.cgi?id=250659
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 20 Mar 2007 18:59:39 +0000 (14:59 -0400)]
USB: add power/level sysfs attribute
This patch (as874) adds another piece to the user-visible part of the
USB autosuspend interface. The new power/level sysfs attribute allows
users to force the device on (with autosuspend off), force the device
to sleep (with autoresume off), or return to normal automatic operation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Stokes [Sat, 17 Mar 2007 14:14:12 +0000 (16:14 +0200)]
USB: ati_remote2: Add channel support
Add logical channel support for ATI Remote Wonder II
The ATI Remote Wonder II can be configured with one of 16 unique logical
channels. Allowing up to 16 remotes to be used independently within
range of each other. This change adds functionality to configure the
receiver and filter the input data to respond or exclude remotes
configured with different logical channels.
Signed-off-by: Peter Stokes <linux@dadeos.freeserve.co.uk> Acked-by: Ville Syrjala <syrjala@sci.fi> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 20 Mar 2007 12:54:05 +0000 (13:54 +0100)]
USB: sierra close race
the sierra driver does not directly use usb_kill_urb(). It uses a wrapper.
This wrapper means that callbacks which are running are not killed during
close, resubmitting and illicitly pushing data into the tty layer.
The whole purpose of usb_kill_urb() is subverted. The wrapper must be removed.
The same problem as the option driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 20 Mar 2007 12:41:21 +0000 (13:41 +0100)]
USB: option close race
the option driver does not directly use usb_kill_urb(). It uses a wrapper.
This wrapper means that callbacks which are running are not killed during
close, resubmitting and illicitly pushing data into the tty layer.
The whole purpose of usb_kill_urb() is subverted. The wrapper must be removed.
Alan Stern [Mon, 19 Mar 2007 19:33:11 +0000 (15:33 -0400)]
UHCI: Add some WARN_ON()s
This patch (as872) adds some WARN_ON()s to various error checks which
are never supposed to fail. Unsettlingly, one of them has shown up in
a user's log! Maybe making the warning more visible and having the
call-stack information available will help pinpoint the source of the
problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap [Sat, 17 Mar 2007 01:33:13 +0000 (18:33 -0700)]
USB: dm9601: fix sparse NULL warnings
Fix sparse NULL warnings:
drivers/usb/net/dm9601.c:88:23: warning: Using plain integer as NULL pointer
drivers/usb/net/dm9601.c:174:22: warning: Using plain integer as NULL pointer
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Fri, 16 Mar 2007 19:28:28 +0000 (20:28 +0100)]
USB: overhaul of mos7840 driver
This fixes:
- breaking DMA rules about buffers
- usage of _global_ variables to save a single device's attributes
- racy access to urb->status
- smp monotonity issue with statistics
- use of one buffer for many simultaneous URBs
- error handling introduced
- several instances of following NULL pointers
- use after free
- unnecessary GFP_ATOMIC
- GFP_KERNEL in interrupt
- various cleanups
- write room granularity issue that bit cdc-acm
- race in shutdown
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 15 Mar 2007 19:54:30 +0000 (15:54 -0400)]
EHCI: add delay to bus_resume before accessing ports
This patch (as870) adds a delay to ehci-hcd's bus_resume routine.
Apparently there are controllers and/or BIOSes out there which need
such a delay to get the ports back into their correct state. This
fixes Bugzilla #8190.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 13 Mar 2007 20:39:15 +0000 (16:39 -0400)]
USB: Allow autosuspend delay to equal 0
This patch (as867) adds an entry for the new power/autosuspend
attribute in Documentation/ABI/testing, and it changes the behavior of
the delay value. Now a delay of 0 means to autosuspend as soon as
possible, and negative values will prevent autosuspend.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 13 Mar 2007 20:37:30 +0000 (16:37 -0400)]
USB: separate autosuspend from external suspend
This patch (as866) adds new entry points for external USB device
suspend and resume requests, as opposed to internally-generated
autosuspend or autoresume. It also changes the existing
remote-wakeup code paths to use the new routines, since remote wakeup
is not the same as autoresume.
As part of the change, it turns out to be necessary to do remote
wakeup of root hubs from a workqueue. We had been using khubd, but it
does autoresume rather than an external resume. Using the
ksuspend_usb_wq workqueue for this purpose seemed a logical choice.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ehci-fsl: change SI_CTRL, PRI_CTRL register offsets according to errata
Correct the offsets of the SI_CTRL, PRI_CTRL registers according to
the Reference Manual errata sheet in order to prevent unwanted
settings regarding burst transactions and priority states.
Signed-off-by: Christian Engelmayer <Christian.Engelmayer@frequentis.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Tue, 13 Mar 2007 15:10:52 +0000 (11:10 -0400)]
USB: fix race in HCD removal
This patch (as865) fixes a race in the HCD removal code discovered by
Milan Plzik. Arrival of an interrupt after the root hub was
unregistered could cause the root-hub status timer to start up, even
after it was supposed to have been shut down. The problem is fixed by
moving the del_timer_sync() call to after the HCD's stop() method, at
which time IRQ generation should be disabled.
Cc: Milan Plzik <milan.plzik@gmail.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simon Arlott [Tue, 6 Mar 2007 10:47:46 +0000 (02:47 -0800)]
USB: MAINTAINERS: cxacru
I've acquired a second device for testing and plan to make some changes in
the near future to export all the device stats to sysfs (based on my
proposed patch to add them to the proc file ~2007-01-30).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Acked-by: Duncan Sands <baldrick@free.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simon Arlott [Tue, 6 Mar 2007 10:47:45 +0000 (02:47 -0800)]
USB: cxacru: export detailed device info through sysfs
When the device is polled for status there is a lot of useful status
information available that is ignored. This patch stores the device info
array when the status is polled and adds sysfs files to the usb device to
allow userspace to query it. Since the device updates its status
internally once a second the poll time is changed to this, and
round_jiffies_relative is used to avoid waking the cpu unnecessarily.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: Duncan Sands <duncan.sands@free.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simon Arlott [Tue, 6 Mar 2007 10:47:43 +0000 (02:47 -0800)]
usbatm: create sysfs link "device" from atm class device to usb interface
There is currently no path from the ATM device in /sys to the USB device's
interface that the driver is using; this patch creates a "device" symlink. It
is then possible to get to the cxacru ADSL statistics
(http://lkml.org/lkml/2007/2/23/328):
If this link is not appropriate I'd have to create device files in
/sys/class/atm/cxacru0 instead - which seems less appropriate since the ADSL
statistics are for the USB device not ATM (which is running over the ADSL).
[akpm@linux-foundation.org: cleanups] Signed-off-by: Simon Arlott <simon@fire.lp0.eu> Cc: Duncan Sands <duncan.sands@math.u-psud.fr> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 9 Mar 2007 20:41:13 +0000 (15:41 -0500)]
usbcore: move usb_autosuspend_work
This patch (as864) moves the work routine for USB autosuspend from one
source file to another. This permits the removal of one whole global
symbol (!) and should smooth the way for more changes in the future.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Fri, 9 Mar 2007 04:02:26 +0000 (20:02 -0800)]
libusual: change block scope variable to function scope
Someone changed the code to kthread and used his style instead of mine.
The problem with the block variables is that they provoke shadowing,
which is actually exactly what has happened in my other tree which
has the class patch.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Sun, 25 Feb 2007 03:27:33 +0000 (19:27 -0800)]
usbmon: Extended text API
This patch adds a new text API, codenamed '1u', which captures more URB
fields than old '1t' interface did. Also the '1u' text API is compatible
with the future "bus zero" extension.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Thu, 1 Mar 2007 13:31:02 +0000 (14:31 +0100)]
USB: fix skeleton driver
compilation of the skeleton driver is currently broken. It doesn't compile.
So while I am it:
- fix typo
- add comments to answer common questions
- actually allow autosuspend in the driver struct
- increase paralellism by restricting code under locks
Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Sat, 24 Feb 2007 20:23:52 +0000 (12:23 -0800)]
pxa2xx_udc: cleanups, use platform_get_irq
Make the pxa2xx_udc driver fetch its IRQ from platform resources
rather than using compile-time constants, so that it works properly
on IXP4xx systems not just PXA21x/25x/26x.
Other updates:
- Do that using platform_get_irq()
- Switch to platform_driver_probe()
- Handle device_add() errors
- Remove "function" sysfs attribute and its potential errors
- Whitespace cleanups
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (46 commits)
dev_dbg: check dev_dbg() arguments
drivers/base/attribute_container.c: use mutex instead of binary semaphore
mod_sysfs_setup() doesn't return errno when kobject_add_dir() failure occurs
s2ram: add arch irq disable/enable hooks
define platform wakeup hook, use in pci_enable_wake()
security: prevent permission checking of file removal via sysfs_remove_group()
device_schedule_callback() needs a module reference
s390: cio: Delay uevents for subchannels
sysfs: bin.c printk fix
Driver core: use mutex instead of semaphore in DMA pool handler
driver core: bus_add_driver should return an error if no bus
debugfs: Add debugfs_create_u64()
the overdue removal of the mount/umount uevents
kobject: Comment and warning fixes to kobject.c
Driver core: warn when userspace writes to the uevent file in a non-supported way
Driver core: make uevent-environment available in uevent-file
kobject core: remove rwsem from struct subsystem
qeth: Remove usage of subsys.rwsem
PHY: remove rwsem use from phy core
IEEE1394: remove rwsem use from ieee1394 core
...
[akpm@linux-foundation.org: fix a couple of things which broke] Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Akinobu Mita [Thu, 26 Apr 2007 07:12:09 +0000 (00:12 -0700)]
mod_sysfs_setup() doesn't return errno when kobject_add_dir() failure occurs
mod_sysfs_setup() doesn't return an errno when kobject_add_dir() for module
"holders" directory fails. So caller of mod_sysfs_setup() will keep going
and get oops.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For powermac, we need to do some things between suspending devices and
device_power_off, for example setting the decrementer. This patch
allows architectures to define arch_s2ram_{en,dis}able_irqs in their
asm/suspend.h to have control over this step.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Pavel Machek <pavel@ucw.cz> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 26 Apr 2007 07:12:06 +0000 (00:12 -0700)]
define platform wakeup hook, use in pci_enable_wake()
This defines a platform hook to enable/disable a device as a wakeup event
source. It's initially for use with ACPI, but more generally it could be used
whenever enable_irq_wake()/disable_irq_wake() don't suffice.
The hook is called -- if available -- inside pci_enable_wake(); and the
semantics of that call are enhanced so that support for PCI PME# is no longer
needed. It can now work for devices with "legacy PCI PM", when platform
support allows it. (That support would use some board-specific signal for for
the same purpose as PME#.)
[akpm@linux-foundation.org: Make it compile with CONFIG_PM=n] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Zhang Rui <rui.zhang@intel.com> Cc: Len Brown <lenb@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
James Morris [Thu, 26 Apr 2007 07:12:05 +0000 (00:12 -0700)]
security: prevent permission checking of file removal via sysfs_remove_group()
Prevent permission checking from being performed when the kernel wants to
unconditionally remove a sysfs group, by introducing an kernel-only variant
of lookup_one_len(), lookup_one_len_kern().
Additionally, as sysfs_remove_group() does not check the return value of
the lookup before using it, a BUG_ON has been added to pinpoint the cause
of any problems potentially caused by this (and as a form of annotation).
Signed-off-by: James Morris <jmorris@namei.org> Cc: Nagendra Singh Tomar <nagendra_tomar@adaptec.com> Cc: Tejun Heo <htejun@gmail.com> Cc: Stephen Smalley <sds@tycho.nsa.gov> Cc: Eric Paris <eparis@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 26 Apr 2007 07:12:04 +0000 (00:12 -0700)]
device_schedule_callback() needs a module reference
This patch (as896b) fixes an oversight in the design of
device_schedule_callback(). It is necessary to acquire a reference to the
module owning the callback routine, to prevent the module from being
unloaded before the callback can run.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: Satyam Sharma <satyam.sharma@gmail.com> Cc: Neil Brown <neilb@suse.de> Cc: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We often have the situation that we register a subchannel and start device
recognition, only to find out that the device is not usable after all, which
triggers an unregister of the subchannel. This often happens on hundreds of
subchannels on a LPAR, leading to a storm of events which aren't of any use.
Therefore, use uevent_suppress to delay the KOBJ_ADD uevent for a subchannel
until we know that its ccw_device is to be registered.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Eric Rannaud <eric.rannaud@gmail.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kay Sievers [Thu, 5 Apr 2007 23:40:38 +0000 (01:40 +0200)]
Driver core: warn when userspace writes to the uevent file in a non-supported way
In the future we will allow the uevent type to be written to the uevent
file to trigger the different types of uevents. But for now, as we only
support the ADD event, warn if userspace tries to write anything else to
this file.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kay Sievers [Thu, 5 Apr 2007 23:40:38 +0000 (01:40 +0200)]
Driver core: make uevent-environment available in uevent-file
This allows sysfs to show the environment variables that are available
if the uevent happens. This lets userspace not have to cache all of
this information as the kernel already knows it.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It isn't used at all by the driver core anymore, and the few usages of
it within the kernel have now all been fixed as most of them were using
it incorrectly. So remove it.
Now the whole struct subsys can be removed from the system, but that's
for a later patch...
Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
the current driver tree contains the removal of subsys.rwsem.
Unfortunately, this breaks qeth. However, it should be no problem to
fix the walking of the devices for /proc/qeth:
No need to take subsys.rwsem during walking the devices,
driver_find_devices() should already suffice.
The subsystem rwsem is not used by the driver core at all, so the use of
it in the phy code doesn't make any sense. They might possibly
want to use a local lock, but I am unsure about that.
The subsystem rwsem is not used by the driver core at all, so the use of
it in the ieee1394 code doesn't make any sense. They might possibly
want to use a local lock, but as most of these operations are already
protected by a local lock, it really doesn't look like it would be
needed.
Cc: Ben Collins <bcollins@debian.org> Cc: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: linux1394-devel <linux1394-devel@lists.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The subsystem rwsem is not used by the driver core at all, so the use of
it in the ide-proc code of it doesn't make any sense. Perhaps a local
lock might be needed, but I do not really think so.
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com> Cc: linux ide <linux-ide@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-2.6 / log