Rafal Bilski [Sun, 7 Oct 2007 07:24:32 +0000 (00:24 -0700)]
Longhaul: add auto enabled "revid_errata" option
VIA C3 Ezra-T has RevisionID equal to 1, but it needs RevisionKey to be 0
or CPU will ignore new frequency and will continue to work at old
frequency. New "revid_errata" option will force RevisionKey to be set to
0, whatever RevisionID is.
Additionaly "Longhaul" will not silently ignore unsuccessful transition.
It will try to check if "revid_errata" or "disable_acpi_c3" options need to
be enabled for this processor/system.
Same for Longhaul ver. 2 support. It will be disabled if none of above
options will work.
Best case scenario (with patch apllied and v2 enabled):
longhaul: VIA C3 'Ezra' [C5C] CPU detected. Longhaul v2 supported.
longhaul: Using northbridge support.
longhaul: VRM 8.5
longhaul: Max VID=1.350 Min VID=1.050, 13 possible voltage scales
longhaul: f: 300000 kHz, index: 0, vid: 1050 mV
[...]
longhaul: Voltage scaling enabled.
Worst case scenario:
longhaul: VIA C3 'Ezra-T' [C5M] CPU detected. Powersaver supported.
longhaul: Using northbridge support.
longhaul: Using ACPI support.
longhaul: VRM 8.5
longhaul: Claims to support voltage scaling but min & max are both 1.250. Voltage scaling disabled
longhaul: Failed to set requested frequency!
longhaul: Enabling "Ignore Revision ID" option.
longhaul: Failed to set requested frequency!
longhaul: Disabling ACPI C3 support.
longhaul: Disabling "Ignore Revision ID" option.
longhaul: Failed to set requested frequency!
longhaul: Enabling "Ignore Revision ID" option.
[akpm@linux-foundation.org: coding-style cleanups] Signed-off-by: Rafal Bilski <rafalbilski@interia.pl> Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Blanchard [Sun, 7 Oct 2007 07:24:31 +0000 (00:24 -0700)]
Fix timer_stats printout of events/sec
When using /proc/timer_stats on ppc64 I noticed the events/sec field wasnt
accurate. Sometimes the integer part was incorrect due to rounding (we
werent taking the fractional seconds into consideration).
The fraction part is also wrong, we need to pad the printf statement and
take the bottom three digits of 1000 times the value.
Signed-off-by: Anton Blanchard <anton@samba.org> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Oct 2007 23:17:38 +0000 (16:17 -0700)]
Don't do load-average calculations at even 5-second intervals
It turns out that there are a few other five-second timers in the
kernel, and if the timers get in sync, the load-average can get
artificially inflated by events that just happen to coincide.
So just offset the load average calculation it by a timer tick.
Noticed by Anders Boström, for whom the coincidence started triggering
on one of his machines with the JBD jiffies rounding code (JBD is one of
the subsystems that also end up using a 5-second timer by default).
Tested-by: Anders Boström <anders@bostrom.dyndns.org> Cc: Chuck Ebbert <cebbert@redhat.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 7 Oct 2007 23:02:55 +0000 (16:02 -0700)]
VT_WAITACTIVE: Avoid returning EINTR when not necessary
We should generally prefer to return ERESTARTNOHAND rather than EINTR,
so that processes with unhandled signals that get ignored don't return
EINTR.
This can help with X startup issues:
Fatal server error:
xf86OpenConsole: VT_WAITACTIVE failed: Interrupted system call
although the real fix is having the X server always retry EINTR
regardless (since EINTR does happen for signals that have handlers
installed). Keithp has a patch for that.
Regardless, ERESTARTNOHAND is the correct thing to use.
Fix non-terminated PCI match table in PowerMac IDE
The PCI device table in the powermac IDE driver isn't properly
terminated. Depending on how your kernel is linked and other random
factors, you can end up with this driver matched against any other PCI
device in your system, possibly crashing at boot.
Thanks to Heikki for tracking this down with me, the bug have been there
for some time, though it rarely hurts due to luck. In this case, the
switch from .22 to .23-rc9 is causing it to show up due to differences
in the resulting layout of .data I suppose.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <pmac@au1.ibm.com> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Cc: Heikki Lindholm <holindho@cs.helsinki.fi> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When pinning and unpinning pagetables, we must protect them against
being used by other CPUs, lest they see the pagetable in an
intermediate read-only-but-not-pinned state.
When using split pte locks, doing this properly would require taking
all the pte locks for the pagetable while pinning, but this may overflow
the PREEMPT_BITS part of the preempt counter if the process has mapped
more than about 512M of memory.
However, failing to take the pte locks causes write-protect faults when
the pageout code is trying to clear the Access bit on a pte which is part
of a freshy created and still being pinned process after fork.
This is a short-term fix until the problem is solved properly.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Acked-by: Rik van Riel <riel@redhat.com> Acked-by: Hugh Dickins <hugh@veritas.com> Cc: David Rientjes <rientjes@google.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andi Kleen <ak@suse.de> Cc: Keir Fraser <keir@xensource.com> Cc: Jan Beulich <jbeulich@novell.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 5 Oct 2007 21:09:10 +0000 (14:09 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4598/2: OSIRIS: Ensure we do not get nRSTOUT during suspend
[ARM] 4597/2: OSIRIS: ensure CPLD0 is preserved after suspend
Ben Dooks [Thu, 4 Oct 2007 22:16:42 +0000 (23:16 +0100)]
[ARM] 4597/2: OSIRIS: ensure CPLD0 is preserved after suspend
Ensure that CPLD is restored to the original state
on resume, and that before going into suspend we
select the NAND bank we booted from for restarting.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 8169/8110SC currently announces itself as:
[...]
eth0: RTL8169sc/8110sc at 0x........, ..:..:..:..:..:.., XID 18000000 IRQ ..
^^^^^^^^
It uses RTL_GIGA_MAC_VER_05 and this part of the changeset can cut
its performance by a factor of 2~2.5 as reported by Timo.
(the driver includes code just before the hunk to write the ChipCmd
register when mac_version == RTL_GIGA_MAC_VER_0[1-4])
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Timo Jantunen <jeti@welho.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linus Torvalds [Fri, 5 Oct 2007 15:08:08 +0000 (08:08 -0700)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix 'niu' complex IRQ probing.
[SPARC64]: check fork_idle() error
[SPARC64]: Temporary workaround for PCI-E slot on T1000.
[SPARC64]: VIO device addition log message level is too high.
[SPARC64]: Fix domain-services port probing.
[SPARC64]: Don't use in/local regs for ldx/stx data in N1 memcpy.
Serge Belyshev [Thu, 4 Oct 2007 21:10:04 +0000 (23:10 +0200)]
Remove unnecessary cast in prefetch()
It is ok to call prefetch() function with NULL argument, as specifically
commented in include/linux/prefetch.h. But in standard C, it is invalid
to dereference NULL pointer (see C99 standard 6.5.3.2 paragraph 4 and
note #84).
prefetch() has a memory reference for its argument.
Newer gcc versions (4.3 and above) will use that to conclude that "x"
argument is non-null and thus wreaking havok everywhere prefetch() was
inlined.
Fixed by removing cast and changing asm constraint.
[ It seems in theory gcc 4.2 could miscompile this too; although no
cases known. In 2.6.24 we should probably switch to
__builtin_prefetch() instead, but this is a simpler fix for now.
-- AK ]
Giuseppe Sacco [Thu, 4 Oct 2007 21:09:12 +0000 (23:09 +0200)]
[MIPS] IP32: Enable PCI bridges
Fixe MACE PCI addressing by adding the bus number parameter.
Remove check of the used slot since every slot should be valid.
Converted mkaddr from #define to inline function.
Signed-off-by: Giuseppe Sacco <eppesuig@debian.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hugh Dickins [Thu, 4 Oct 2007 15:56:06 +0000 (16:56 +0100)]
Fix sys_remap_file_pages BUG at highmem.c:15!
Gurudas Pai reports kernel BUG at arch/i386/mm/highmem.c:15! below
sys_remap_file_pages, while running Oracle database test on x86 in 6GB
RAM: kunmap thinks we're in_interrupt because the preempt count has
wrapped.
That's because __do_fault expected to unmap page_table, but one of its
two callers do_nonlinear_fault already unmapped it: let do_linear_fault
unmap it first too, and then there's no need to pass the page_table arg
down.
Why have we been so slow to notice this? Probably through forgetting
that the mapping_cap_account_dirty test means that sys_remap_file_pages
nowadays only goes the full nonlinear vma route on a few memory-backed
filesystems like ramfs, tmpfs and hugetlbfs.
[ It also depends on CONFIG_HIGHPTE, so it becomes even harder to
trigger in practice. Many who have need of large memory have probably
migrated to x86-64..
FUJITA Tomonori [Wed, 3 Oct 2007 00:00:58 +0000 (09:00 +0900)]
[SCSI] megaraid_old: fix READ_CAPACITY
The bulk transfer mode got eleminated by 3f6270ef76f2ce5c134615a470685d6c2a66c07e. Unfortunately, this mode is
required for READ_CAPACITY commands on certain cards, so put it back
again. This fixes a boot failure regression reported by Burton
Windle.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
David S. Miller [Thu, 4 Oct 2007 04:37:57 +0000 (21:37 -0700)]
[SPARC64]: Temporary workaround for PCI-E slot on T1000.
The PCI-E slot on T1000 connects directly to the Fire PCI chip with no
intervening bridges visible in the OBP tree.
Unfortunately the bus numbering of the device in that slot is
different (2) from the PCI host controller (0), and thus the
pci_bus_{read,write}_config_*() calls don't work out.
Complicating things further the Fire PCI controller has no config
space it responds to either.
For now treat this case specially so that devices in the slot work.
Longer term we need to perhaps cons up a dummy bridge between the Fire
and the PCI-E slot so that the bus hierarchy is complete inside of the
kernel and thus the bus numbering all works out right.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 3 Oct 2007 22:43:17 +0000 (15:43 -0700)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Terminally fix local_{dec,sub}_if_positive
[MIPS] Type proof reimplementation of cmpxchg.
[MIPS] pg-r4k.c: Fix a typo in an R4600 v2 erratum workaround
Linus Torvalds [Wed, 3 Oct 2007 22:34:07 +0000 (15:34 -0700)]
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: fix PORT_J BUG for BF537/6 EMAC driver reported by Kalle Pokki <kalle.pokki@iki.fi>
Blackfin arch: gpio pinmux and resource allocation API required by BF537 on chip ethernet mac driver
Blackfin arch: add some missing syscall
binfmt_flat: checkpatch fixing minimum support for the blackfin relocations
Binfmt_flat: Add minimum support for the Blackfin relocations
Olof Johansson [Wed, 3 Oct 2007 01:45:27 +0000 (20:45 -0500)]
libata: fix for sata_mv >64KB DMA segments
Fix bug in sata_mv for cases where the IOMMU layer has merged SG entries
to larger than 64KB. They need to be split up before being sent to
the driver.
Just for simplicity's sake, split up at 64K boundary instead of 64K size,
since that's what the common code does anyway.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unneeded check that caused problems with jumbo frame sizes.
The check was recently added and is wrong.
When using jumbo frames the sky2 driver does fragmentation, so
rx_data_size is less than mtu.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ralf Baechle [Wed, 3 Oct 2007 13:29:19 +0000 (14:29 +0100)]
[MIPS] Terminally fix local_{dec,sub}_if_positive
They contain 64-bit instructions so wouldn't work on 32-bit kernels or
32-bit hardware. Since there are no users, blow them away. They
probably were only ever created because there are atomic_sub_if_positive
and atomic_dec_if_positive which exist only for sake of semaphores.
CC net/ieee80211/softmac/ieee80211softmac_wx.o
/home/kernel/src/net/ieee80211/softmac/ieee80211softmac_wx.c: In function â\80\98ieee80211softmac_wx_set_essidâ\80\99:
/home/kernel/src/net/ieee80211/softmac/ieee80211softmac_wx.c:117: warning: label â\80\98outâ\80\99 defined but not used
David S. Miller [Tue, 2 Oct 2007 23:17:17 +0000 (16:17 -0700)]
[SPARC64]: Don't use in/local regs for ldx/stx data in N1 memcpy.
It doesn't matter for use in 64-bit objects, but when used in
32-bit environments the top 32-bits of the local and in
registers will get chopped off on the next register window
spill/restore which leads to difficult to track down and
subtle bugs.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 2 Oct 2007 17:35:28 +0000 (10:35 -0700)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix missing load-twin usage in Niagara-1 memcpy.
[SPARC64]: Fix put_user() calls in binfmt_aout32.c
[SPARC]: Fix EBUS use of uninitialized variable.
Linus Torvalds [Tue, 2 Oct 2007 17:34:49 +0000 (10:34 -0700)]
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IEEE80211]: avoid integer underflow for runt rx frames
[TCP]: secure_tcp_sequence_number() should not use a too fast clock
[SFQ]: Remove artificial limitation for queue limit.
Dale Farnsworth [Mon, 1 Oct 2007 23:02:18 +0000 (16:02 -0700)]
mv643xx_eth: Do not modify struct netdev tx_queue_len
This driver erroneously zeros dev->tx_queue_len, since
mp->tx_ring_size has not yet been initialized. Actually,
the driver shouldn't modify tx_queue_len at all and should
leave the value set by alloc_etherdev(), currently 1000.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
David S. Miller [Tue, 2 Oct 2007 08:03:09 +0000 (01:03 -0700)]
[SPARC64]: Fix missing load-twin usage in Niagara-1 memcpy.
For the case where the source is not aligned modulo 8
we don't use load-twins to suck the data in and this
kills performance since normal loads allocate in the
L1 cache (unlike load-twin) and thus big memcpys swipe
the entire L1 D-cache.
We need to allocate a register window to implement this
properly, but that actually simplifies a lot of things
as a nice side-effect.
Signed-off-by: David S. Miller <davem@davemloft.net>
[IEEE80211]: avoid integer underflow for runt rx frames
Reported by Chris Evans <scarybeasts@gmail.com>:
> The summary is that an evil 80211 frame can crash out a victim's
> machine. It only applies to drivers using the 80211 wireless code, and
> only then to certain drivers (and even then depends on a card's
> firmware not dropping a dubious packet). I must confess I'm not
> keeping track of Linux wireless support, and the different protocol
> stacks etc.
>
> Details are as follows:
>
> ieee80211_rx() does not explicitly check that "skb->len >= hdrlen".
> There are other skb->len checks, but not enough to prevent a subtle
> off-by-two error if the frame has the IEEE80211_STYPE_QOS_DATA flag
> set.
>
> This leads to integer underflow and crash here:
>
> if (frag != 0)
> flen -= hdrlen;
>
> (flen is subsequently used as a memcpy length parameter).
How about this?
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 1 Oct 2007 20:58:36 +0000 (13:58 -0700)]
[TCP]: secure_tcp_sequence_number() should not use a too fast clock
TCP V4 sequence numbers are 32bits, and RFC 793 assumed a 250 KHz clock.
In order to follow network speed increase, we can use a faster clock, but
we should limit this clock so that the delay between two rollovers is
greater than MSL (TCP Maximum Segment Lifetime : 2 minutes)
Choosing a 64 nsec clock should be OK, since the rollovers occur every
274 seconds.
[SFQ]: Remove artificial limitation for queue limit.
This is followup to Patrick's patch. A little optimization to enqueue
routine allows to remove artificial limitation on queue length.
Plus, testing showed that hash function used by SFQ is too bad or even worse.
It does not even sweep the whole range of hash values.
Switched to Jenkins' hash.
Signed-off-by: Alexey Kuznetsov <kaber@ms2.inr.ac.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Andi Kleen [Mon, 1 Oct 2007 08:20:08 +0000 (01:20 -0700)]
x86_64: increase VDSO_TEXT_OFFSET for ancient binutils
For some reason old binutils genertate larger headers so increase the text
offset of the vdso to avoid linker errors.
Roland McGrath explains:
"There are extra symbols in the '.dynsym' section that are responsible
for the size difference (They also cause corresponding inflation in
'.gnu.version')
Older ld's wrongly generated these unneeded symbols in .dynsym. This
was fixed not all that long ago (2006); binutils-2.17.50.0.6 might be
the first fixed version, but I have not verified for sure where the
cutoff was.
The unneeded symbols et al from old ld add almost 700 bytes excess.
This limits fairly tightly the amount by which the actual text and
data in the vDSO can grow in the future without pushing the whole
file over 4kb. If it does grow later on, we should consider changing
the layout with a config option or something to pack it better
without that padding, when building the kernel with newer binutils."
Signed-off-by: Andi Kleen <ak@suse.de> Cc: Roland McGrath <roland@redhat.com> Cc: Badari Pulavarty <pbadari@us.ibm.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In a desperate attempt to get a changelog entry in 2.6.23, I took a look
into it.
It turns out we are passing a real and not a virtual irq into
get_irq_server. This works for the case where hwirq < NR_IRQS and we
set virq = hwirq. In my case however hwirq = 590082 and we try and
access irq_desc[590082], slightly past the end at 512 entries.
Lucky we ship lots of memory with our machines.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linus Torvalds [Mon, 1 Oct 2007 20:17:28 +0000 (13:17 -0700)]
Fix possible splice() mmap_sem deadlock
Nick Piggin points out that splice isn't being good about the mmap
semaphore: while two readers can nest inside each others, it does leave
a possible deadlock if a writer (ie a new mmap()) comes in during that
nesting.
Original "just move the locking" patch by Nick, replaced by one by me
based on an optimistic pagefault_disable(). And then Jens tested and
updated that patch.
Reported-by: Nick Piggin <npiggin@suse.de> Tested-by: Jens Axboe <jens.axboe@oracle.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lachlan McIlroy says:
It tried to fix an issue where log replay is replaying an inode cluster
initialisation transaction that should not be replayed because the inode
cluster on disk is more up to date. Since we don't log file sizes (we
rely on inode flushing to get them to disk) then we can't just replay
all the transations in the log and expect the inode to be completely
restored. We lose file size updates. Unfortunately this fix is causing
more (serious) problems than it is fixing.
Calling handle_futex_death in exit_robust_list for the different robust
mutexes of a thread basically frees the mutex. Another thread might grab
the lock immediately which updates the next pointer of the mutex.
fetch_robust_entry over the next pointer might therefore branch into the
robust mutex list of a different thread. This can cause two problems: 1)
some mutexes held by the dead thread are not getting freed and 2) some
mutexs held by a different thread are freed.
The next point need to be read before calling handle_futex_death.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Samuel Ortiz [Mon, 1 Oct 2007 08:20:12 +0000 (01:20 -0700)]
VT ioctl race fix
When calling the RELDISP VT ioctl, we are reading vt_newvt while the
console workqueue could be messing with it (through change_console()). We
fix this race by taking the console semaphore before reading vt_newvt.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com> Acked-by: Antonino Daplas <adaplas@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark Lord [Mon, 1 Oct 2007 08:20:10 +0000 (01:20 -0700)]
Fix SMP poweroff hangs
We need to disable all CPUs other than the boot CPU (usually 0) before
attempting to power-off modern SMP machines. This fixes the
hang-on-poweroff issue on my MythTV SMP box, and also on Thomas Gleixner's
new toybox.
Signed-off-by: Mark Lord <mlord@pobox.com> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ralf Baechle [Mon, 1 Oct 2007 08:20:10 +0000 (01:20 -0700)]
hugetlb: fix clear_user_highpage arguments
The virtual address space argument of clear_user_highpage is supposed to be
the virtual address where the page being cleared will eventually be mapped.
This allows architectures with virtually indexed caches a few clever
tricks. That sort of trick falls over in painful ways if the virtual
address argument is wrong.
Dave Jones [Mon, 1 Oct 2007 08:20:09 +0000 (01:20 -0700)]
Add /dev/oldmem to devices.txt documentation
Signed-off-by: Dave Jones <davej@redhat.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: <device@lanana.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Store any note sections after the exception tables like the other
architectures do. This is required for .note.gnu.build-id emitted from
binutils 2.18 onwards if nothing else.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A "cleanup" almost two years ago deleted the old definition from
<asm/fcntl.h>, so asm-generic/fcntl.h defaulted it to the the same
value as FASYNC ... which happened to be the wrong thing.
Ian Armstrong [Sat, 18 Aug 2007 18:58:51 +0000 (15:58 -0300)]
V4L/DVB (6052): ivtv: fix udma yuv bug
Using udma yuv causes the driver becomes locked into that mode. This prevents
use of the mpeg decoder & non-udma yuv output. This patch clears the
operating mode when the device is closed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jan Lübbe [Sat, 29 Sep 2007 16:47:51 +0000 (18:47 +0200)]
fix console change race exposed by CFS
The new behaviour of CFS exposes a race which occurs if a switch is
requested when vt_mode.mode is VT_PROCESS.
The process with vc->vt_pid is signaled before vc->vt_newvt is set.
This causes the switch to fail when triggered by the monitoing process
because the target is still -1.
[ If the signal sending fails, the subsequent "reset_vc(vc)" will then
reset vt_newvt to -1, so this works for that case too. - Linus ]
Signed-off-by: Jan Lübbe <jluebbe@lasnet.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nick Piggin [Sat, 29 Sep 2007 13:28:48 +0000 (15:28 +0200)]
i386: remove bogus comment about memory barrier
The comment being removed by this patch is incorrect and misleading.
In the following situation:
1. load ...
2. store 1 -> X
3. wmb
4. rmb
5. load a <- Y
6. store ...
4 will only ensure ordering of 1 with 5.
3 will only ensure ordering of 2 with 6.
Further, a CPU with strictly in-order stores will still only provide that
2 and 6 are ordered (effectively, it is the same as a weakly ordered CPU
with wmb after every store).
In all cases, 5 may still be executed before 2 is visible to other CPUs!
The additional piece of the puzzle that mb() provides is the store/load
ordering, which fundamentally cannot be achieved with any combination of
rmb()s and wmb()s.
This can be an unexpected result if one expected any sort of global ordering
guarantee to barriers (eg. that the barriers themselves are sequentially
consistent with other types of barriers). However sfence or lfence barriers
need only provide an ordering partial ordering of memory operations -- Consider
that wmb may be implemented as nothing more than inserting a special barrier
entry in the store queue, or, in the case of x86, it can be a noop as the store
queue is in order. And an rmb may be implemented as a directive to prevent
subsequent loads only so long as their are no previous outstanding loads (while
there could be stores still in store queues).
I can actually see the occasional load/store being reordered around lfence on
my core2. That doesn't prove my above assertions, but it does show the comment
is wrong (unless my program is -- can send it out by request).
So:
mb() and smp_mb() always have and always will require a full mfence
or lock prefixed instruction on x86. And we should remove this comment.
Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Paul McKenney <paulmck@us.ibm.com> Cc: David Howells <dhowells@redhat.com> Cc: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 468d09f8946d40228c56de26fe4874b2f98067ed masked the "state"
interrupt (bit 20 of the cause register). This results in Radstone's
PPC7D repeatedly re-entering the interrupt routine, locking up the
board. The following patch returns the required handling for this
interrupt.
Linas reported me that some machines were crashing at boot in
quirk_e100_interrupt. It appears that this quirk is doing an ioremap
directly on a PCI BAR value, which isn't legal and will cause all sorts
of bad things to happen on architectures where PCI BARs don't directly
match processor bus addresses.
This fixes it by using the proper PCI resources instead which is possible
since the quirk has been moved by a previous commit to happen late enough
for that.
Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TCP]: Fix MD5 signature handling on big-endian.
[NET]: Zero length write() on socket should not simply return 0.
It doesn't look as if the NFS file name limit is being initialised correctly
in the struct nfs_server. Make sure that we limit whatever is being set in
nfs_probe_fsinfo() and nfs_init_server().
Also ensure that readdirplus and nfs4_path_walk respect our file name
limits.
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
e1000: Add device IDs of blade version of the 82571 quad port
sky2: fix transmit state on resume
sky2: FE+ vlan workaround
sky2: sky2 FE+ receive status workaround
David S. Miller [Fri, 28 Sep 2007 22:18:35 +0000 (15:18 -0700)]
[TCP]: Fix MD5 signature handling on big-endian.
Based upon a report and initial patch by Peter Lieven.
tcp4_md5sig_key and tcp6_md5sig_key need to start with
the exact same members as tcp_md5sig_key. Because they
are both cast to that type by tcp_v{4,6}_md5_do_lookup().
Unfortunately tcp{4,6}_md5sig_key use a u16 for the key
length instead of a u8, which is what tcp_md5sig_key
uses. This just so happens to work by accident on
little-endian, but on big-endian it doesn't.
Instead of casting, just place tcp_md5sig_key as the first member of
the address-family specific structures, adjust the access sites, and
kill off the ugly casts.
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix fallocate on o32 binary compat ABI
[MIPS] Fix CONFIG_BUILD_ELF64 kernels with symbols in CKSEG0.
[MIPS] IP32: Fix initialization of UART base addresses.
H. Peter Anvin [Fri, 28 Sep 2007 00:17:12 +0000 (17:17 -0700)]
[x86 setup] Correct the SMAP check for INT 0x15, AX=0xe820
The e820 probe code was checking %edx, not %eax, for the SMAP
signature on return. This worked on *almost* all systems, since %edx
still contained SMAP from the call on entry, but on a handful of
systems it failed -- plus, we would have missed real mismatches.
The error output is "=d" to make sure gcc knows %edx is clobbered
here.
mpc834x USB-MPH configuration got broken by commit 6f442560021aecf08658e26ed9a37e6928ef0fa1. The selection bits in SICRL
should be cleared rather than set to configure the USB MUXes for the MPH.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
projects / linux-2.6 / log