Liam Girdwood [Thu, 10 Nov 2005 17:45:39 +0000 (17:45 +0000)]
[ARM] 3098/1: pxa2xx disable ssp irq
Patch from Liam Girdwood
This patch allows users of the pxa SSP driver to register their own irq
handlers instead of using the default SSP handler. It also cleans up the
CKEN clock and irq detection as the values are now stored in a table.
This patch replaces 2845/1
Changes:-
o Added flags parameter to ssp_init()
o Added SSP_NO_IRQ flag to disable registering of ssp irq handler (for
drivers that want to register their own handler)
o Cleaned up clock and irq detection, values are now stored in table.
o Added build changes to allow other drivers (e.g audio) to select the
ssp driver.
o corgi_ssp.c changed to use new interface.
Signed-off-by: Liam Girdwood <liam.girdwood@wolfsonmicro.com> Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Richard Purdie [Thu, 10 Nov 2005 17:42:29 +0000 (17:42 +0000)]
[ARM] 3096/1: Add SharpSL Zaurus power and battery management core driver
Patch from Richard Purdie
This patch adds a power and battery management core driver which with
the addition of the right device files, supports the c7x0 and cxx00
series of Sharp Zaurus handhelds.
The driver is complex for several reasons. Battery charging is manually
monitored and controlled. When suspended, the device needs to
periodically partially resume, check the charging status and then
re-suspend. It does without bothering the higher linux layers as
a full resume and re-suspend is unnecessary. The code is carefully
written to avoid interrupts or calling code outside the module under
these circumstances. It also vets the various wake up sources and
monitors the device's power situation.
Hooks to limit the backlight intensity and to notify the battery
monitoring code of backlight events are connected/added as the
backlight is one of the biggest users of power on the device.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tony Lindgren [Thu, 10 Nov 2005 14:26:51 +0000 (14:26 +0000)]
[ARM] 3145/1: OMAP 3a/5: Add support for omap24xx
Patch from Tony Lindgren
This patch adds support for omap24xx series of processors.
The files live in arch/arm/mach-omap2, and share common
files with omap15xx and omap16xx processors in
arch/arm/plat-omap.
Omap24xx support was originally added for 2.6.9 by TI.
This code was then improved and integrated to share common
code with omap15xx and omap16xx processors by various
omap developers, such as Paul Mundt, Juha Yrjola, Imre Deak,
Tony Lindgren, Richard Woodruff, Nishant Menon, Komal Shah
et al.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tony Lindgren [Thu, 10 Nov 2005 14:26:48 +0000 (14:26 +0000)]
[ARM] 3141/1: OMAP 1/5: Update omap1 specific files
Patch from Tony Lindgren
This patch syncs the mainline kernel with linux-omap tree.
The highlights of the patch are:
- Omap1 serial pport and framebuffer init updates by Imre Deak
- Add support for omap310 processor and Palm Tungsten E PDA
by Laurent Gonzales, Romain Goyet, et al. Omap310 and
omap1510 processors are now handled as omap15xx.
- Omap1 specific changes to shared omap clock framework
by Tony Lindgren
- Omap1 specific changes to shared omap pin mux framework
by Tony Lindgren
- Other misc fixes, such as update memory timings for smc91x,
omap1 specific device initialization etc.
Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Alessandro Zummo [Thu, 10 Nov 2005 14:05:04 +0000 (14:05 +0000)]
[ARM] 3140/1: NSLU2 machine support
Patch from Alessandro Zummo
This patch adds support for the LinkSys NSLU2 running with
both big and little-endian kernels. The LinkSys NSLU2 is
a cost engineered ARM, XScale 420 based system similar to
the the Intel IXDP425 evaluation board. It uses the
IXP4XX ARCH.
While this patch applies independently of other patches
the resultant kernel requires further patches to successfully
use onboard devices, including the onboard flash. Since these
patches are independent of this one they will be submitted
separately.
A defconfig is not included here because not all of
the required drivers are actually in the kernel.
We intend to provide one as soon as the patches
will be incorporated in mainstream.
This patch is the combined work of nslu2-linux.org
Signed-off-by: John Bowler <jbowler@acm.org> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Deepak Saxena <dsaxena@plexity.net> Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Igor Popik [Thu, 6 Oct 2005 18:32:58 +0000 (20:32 +0200)]
[PCMCIA] i82365: release all resources if no devices are found
The i82365 driver does not release all the resources when the device is not
found. This can cause an oops when reading /proc/ioports after module
unload.
Signed-off-by: Igor Popik <igor.popik@gmail.com> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Paul Mackerras [Thu, 10 Nov 2005 05:06:30 +0000 (16:06 +1100)]
ppc64: Add declarations to ppc64 headers as well as powerpc headers
For now, we need these declarations that we moved from C code in
the asm-ppc64 versions of these headers as well as the asm-powerpc
versions. The asm-ppc64 versions will be disappearing shortly.
Linas Vepstas [Fri, 4 Nov 2005 00:50:48 +0000 (18:50 -0600)]
[PATCH] ppc64: mark failed devices
17-eeh-slot-marking-bug.patch
A device that experiences a PCI outage may be just one deivce out
of many that was affected. In order to avoid repeated reports of
a failure, the entire tree of affected devices should be marked
as failed. This patch marks up the entire tree.
Signed-off-by: Linas Vepstas <linas@linas.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Thu, 10 Nov 2005 04:26:20 +0000 (15:26 +1100)]
[PATCH] powerpc: Move more ppc64 files with no ppc32 equivalent to powerpc
This patch moves a bunch more files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
hvcall.h
proc_ppc64.c
sysfs.c
lparcfg.c
rtas_pci.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
phbs_remap_io(), which maps the PCI IO space into the kernel virtual space,
is called too early on powermac, and thus doesn't work.
This fixes it by removing the call from all platforms and putting it back
into the ppc64 common code where it belongs, after the actual probing of
the bus.
That means that before that call, only the ISA IO space (if any) is mapped,
any PIO access (from quirks for example) will fail. This happens not to be
a problem for now, but we'll have to rework that code if it becomes one in
the future.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
That DART (U3 iommu) code didn't properly scale the number of entries
when using !4k pages. That caused crashes when booting G5s with more
than 2Gb of RAM. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Trond Myklebust [Thu, 10 Nov 2005 02:45:24 +0000 (21:45 -0500)]
[PATCH] SUNRPC: don't reencode when looping in call transmit.
If the call to xprt_transmit() fails due to socket buffer space
exhaustion, we do not need to re-encode the RPC message when we
loop back through call_transmit.
Re-encoding can actually end up triggering the WARN_ON() in
call_decode() if we re-encode something like a read() request and
auth->au_rslack has changed.
It can also cause us to increment the RPCSEC_GSS sequence number
beyond the limits of the allowed window.
Paul Mackerras [Thu, 10 Nov 2005 03:30:20 +0000 (14:30 +1100)]
powerpc: 32-bit fixes for xmon
This makes the memory examine/change command print the address as
8 digits instead of 16, and makes the memory dump command print
4 4-byte values per line instead of 2 8-byte values.
Paul Mackerras [Thu, 10 Nov 2005 03:29:18 +0000 (14:29 +1100)]
powerpc: Add user CPU features for POWER4, POWER5, POWER5+ and Cell.
This is at the request of the glibc folks, who want to use these bits
to select libraries optimized for the microarchitecture and new
instructions in these processors.
Paul Mackerras [Thu, 10 Nov 2005 03:28:03 +0000 (14:28 +1100)]
powerpc: Fix SMP time initialization problem
We were getting the last_jiffy per-cpu variable set ahead of the current
timebase in smp_space_timers on SMP machines. This caused the loop in
timer_interrupt to loop virtually forever, since tb_ticks_since assumes
that it will never be called with the timebase behind the last_jiffy
value.
Paul Mackerras [Thu, 10 Nov 2005 02:37:51 +0000 (13:37 +1100)]
[PATCH] powerpc: merge code values for identifying platforms
This patch merges platform codes. systemcfg->platform is no longer used,
systemcfg use in general is deprecated as much as possible (and renamed
_systemcfg before it gets completely moved elsewhere in a future patch),
_machine is now used on ppc64 along as ppc32. Platform codes aren't gone
yet but we are getting a step closer. A bunch of asm code in head[_64].S
is also turned into C code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch consolidates macros used to generate assembly for
compatibility across different CPUs or configs. A new header,
asm-powerpc/asm-compat.h contains the main compatibility macros. It
uses some preprocessor magic to make the macros suitable both for use
in .S files, and in inline asm in .c files. Headers (bitops.h,
uaccess.h, atomic.h, bug.h) which had their own such compatibility
macros are changed to use asm-compat.h.
ppc_asm.h is now for use in .S files *only*, and a #error enforces
that. As such, we're a lot more careless about namespace pollution
here than in asm-compat.h.
While we're at it, this patch adds a call to the PPC405_ERR77 macro in
futex.h which should have had it already, but didn't.
Built and booted on pSeries, Maple and iSeries (ARCH=powerpc). Built
for 32-bit powermac (ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Thu, 10 Nov 2005 00:50:16 +0000 (11:50 +1100)]
[PATCH] powerpc: Merge cacheflush.h and cache.h
The ppc32 and ppc64 versions of cacheflush.h were almost identical.
The two versions of cache.h are fairly similar, except for a bunch of
register definitions in the ppc32 version which probably belong better
elsewhere. This patch, therefore, merges both headers. Notable
points:
- there are several functions in cacheflush.h which exist only
on ppc32 or only on ppc64. These are handled by #ifdef for now, but
these should probably be consolidated, along with the actual code
behind them later.
- Confusingly, both ppc32 and ppc64 have a
flush_dcache_range(), but they're subtly different: it uses dcbf on
ppc32 and dcbst on ppc64, ppc64 has a flush_inval_dcache_range() which
uses dcbf. These too should be merged and consolidated later.
- Also flush_dcache_range() was defined in cacheflush.h on
ppc64, and in cache.h on ppc32. In the merged version it's in
cacheflush.h
- On ppc32 flush_icache_range() is a normal function from
misc.S. On ppc64, it was wrapper, testing a feature bit before
calling __flush_icache_range() which does the actual flush. This
patch takes the ppc64 approach, which amounts to no change on ppc32,
since CPU_FTR_COHERENT_ICACHE will never be set there, but does mean
renaming flush_icache_range() to __flush_icache_range() in
arch/ppc/kernel/misc.S and arch/powerpc/kernel/misc_32.S
- The PReP register info from asm-ppc/cache.h has moved to
arch/ppc/platforms/prep_setup.c
- The 8xx register info from asm-ppc/cache.h has moved to a
new asm-powerpc/reg_8xx.h, included from reg.h
- flush_dcache_all() was defined on ppc32 (only), but was
never called (although it was exported). Thus this patch removes it
from cacheflush.h and from ARCH=powerpc (misc_32.S) entirely. It's
left in ARCH=ppc for now, with the prototype moved to ppc_ksyms.c.
Built for Walnut (ARCH=ppc), 32-bit multiplatform (pmac, CHRP and PReP
ARCH=ppc, pmac and CHRP ARCH=powerpc). Built and booted on POWER5
LPAR (ARCH=powerpc and ARCH=ppc64).
Built for 32-bit powermac (ARCH=ppc and ARCH=powerpc). Built and
booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64). Built and booted
on G5 (ARCH=powerpc)
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Thomas Graf [Thu, 10 Nov 2005 01:25:56 +0000 (02:25 +0100)]
[NETLINK]: Generic netlink family
The generic netlink family builds on top of netlink and provides
simplifies access for the less demanding netlink users. It solves
the problem of protocol numbers running out by introducing a so
called controller taking care of id management and name resolving.
Generic netlink modules register themself after filling out their
id card (struct genl_family), after successful registration the
modules are able to register callbacks to command numbers by
filling out a struct genl_ops and calling genl_register_op(). The
registered callbacks are invoked with attributes parsed making
life of simple modules a lot easier.
Although generic netlink modules can request static identifiers,
it is recommended to use GENL_ID_GENERATE and to let the controller
assign a unique identifier to the module. Userspace applications
will then ask the controller and lookup the idenfier by the module
name.
Due to the current multicast implementation of netlink, the number
of generic netlink modules is restricted to 1024 to avoid wasting
memory for the per socket multiacst subscription bitmask.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces netlink_run_queue() to handle the receive queue of
a netlink socket in a generic way. Processes as much as there
was in the queue upon entry and invokes a callback function
for each netlink message found. The callback function may
refuse a message by returning a negative error code but setting
the error pointer to 0 in which case netlink_run_queue() will
return with a qlen != 0.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Introduces a new type-safe interface for netlink message and
attributes handling. The interface is fully binary compatible
with the old interface towards userspace. Besides type safety,
this interface features attribute validation capabilities,
simplified message contstruction, and documentation.
The resulting netlink code should be smaller, less error prone
and easier to understand.
Signed-off-by: Thomas Graf <tgraf@suug.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Mackerras [Thu, 10 Nov 2005 01:00:55 +0000 (12:00 +1100)]
ppc/powerpc: workarounds for old Open Firmware versions
This adds code to work around some problems with old versions of
Open Firmware, such as on the early powermacs (7500 etc.) and the
"Longtrail" CHRP machine. On these machines we have to claim
the physical and virtual address ranges explicitly when claiming
memory and then set up a V->P mapping.
The Longtrail has more problems: setprop doesn't work, and we have
to set an "allow-reclaim" variable to 0 in order to get claim on
physical memory ranges to fail if the memory is already claimed.
Yasuyuki Kozakai [Thu, 10 Nov 2005 00:38:16 +0000 (16:38 -0800)]
[NETFILTER]: Add nf_conntrack subsystem.
The existing connection tracking subsystem in netfilter can only
handle ipv4. There were basically two choices present to add
connection tracking support for ipv6. We could either duplicate all
of the ipv4 connection tracking code into an ipv6 counterpart, or (the
choice taken by these patches) we could design a generic layer that
could handle both ipv4 and ipv6 and thus requiring only one sub-protocol
(TCP, UDP, etc.) connection tracking helper module to be written.
In fact nf_conntrack is capable of working with any layer 3
protocol.
The existing ipv4 specific conntrack code could also not deal
with the pecularities of doing connection tracking on ipv6,
which is also cured here. For example, these issues include:
1) ICMPv6 handling, which is used for neighbour discovery in
ipv6 thus some messages such as these should not participate
in connection tracking since effectively they are like ARP
messages
2) fragmentation must be handled differently in ipv6, because
the simplistic "defrag, connection track and NAT, refrag"
(which the existing ipv4 connection tracking does) approach simply
isn't feasible in ipv6
3) ipv6 extension header parsing must occur at the correct spots
before and after connection tracking decisions, and there were
no provisions for this in the existing connection tracking
design
4) ipv6 has no need for stateful NAT
The ipv4 specific conntrack layer is kept around, until all of
the ipv4 specific conntrack helpers are ported over to nf_conntrack
and it is feature complete. Once that occurs, the old conntrack
stuff will get placed into the feature-removal-schedule and we will
fully kill it off 6 months later.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: Arnaldo Carvalho de Melo <acme@mandriva.com>
Linas Vepstas [Fri, 4 Nov 2005 00:50:17 +0000 (18:50 -0600)]
[PATCH] ppc64: Save & restore of PCI device BARS
14-eeh-device-bar-save.patch
After a PCI device has been resest, the device BAR's and other config
space info must be restored to the same state as they were in when
the firmware first handed us this device. This will allow the
PCI device driver, when restarted, to correctly recognize and set up
the device.
Tis patch saves the device config space as early as reasonable after
the firmware has handed over the device. Te state resore funcion
is inteded for use by the EEH recovery routines.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:50:10 +0000 (18:50 -0600)]
[PATCH] ppc64: PCI reset support routines
13-eeh-recovery-support-routines.patch
EEH Recovery support routines
This patch adds routines required to help drive the recovery of
EEH-frozen slots. The main function is to drive the PCI #RST
signal line high for a qurter of a second, and then allow for
a second & a half of settle time.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:50:04 +0000 (18:50 -0600)]
[PATCH] ppc64: PCI error event dispatcher
12-eeh-event-dispatcher.patch
ppc64: EEH Recovery dispatcher thread
This patch adds a mechanism to create recovery threads when an
EEH event is received. Since an EEH freeze state may be detected
within an interrupt context, we need to get out of the interrupt
context before starting recovery. This dispatcher does this in
two steps: first, it uses a workqueue to get out, and then
lanuches a kernel thread, so that the recovery routine can
sleep for exteded periods without upseting the keventd.
A kernel thread is created with each EEH event, rather than
having one long-running daemon started at boot time. This is
because it is anticipated that EEH events will be very rare
(very very rare, ideally) and so its pointless to cluter the
process tables with a daemon that will almost never run.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Bugfix: With the curent linux-2.6.14-rc2-git6, EEH errors are
ignored because thier detection requires an unused, uninitialized
flag to be set. This patch removes the unused flag.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:49:38 +0000 (18:49 -0600)]
[PATCH] ppc64: bugfix: crash on PCI hotplug
09-hotplug-bugfix.patch
In the current 2.6.14-rc2-git6 kernel, performing a Dynamic LPAR Add
of a hotplug slot will crash the system, with the following (abbreviated)
stack trace:
The root cause was that __init __alloc_bootmem() was called long after
boot had finished, resulting in a crash because this routine is undefined
after boot time. The patch below fixes this crash, and adds some docs to
clarify the code.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:49:31 +0000 (18:49 -0600)]
[PATCH] ppc64: escape hatch for spinning interrupt deadlocks
08-eeh-spin-counter.patch
One an EEH event is triggers, all further I/O to a device is blocked (until
reset). Bad device drivers may end up spinning in their interrupt handlers,
trying to read an interrupt status register that will never change state.
This patch moves that spin counter to a per-device structure, and adds
some diagnostic prints to help locate the bad driver.
Signed-off-by: Linas Vepstas <linas@linas.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:49:23 +0000 (18:49 -0600)]
[PATCH] ppc64: serialize reports of PCI errors
07-eeh-report-race.patch
When a PCI slot is isolated, all PCI functions under that slot are affected.
If hese functions have separate device drivers, the EEH isolation event
might be reported multiple times. This patch adds a lock to prevent the
racing of such multiple reports. It also marks every device under the slot
as having experienced an EEH event, so that multiple reports may be
recognized more easily.
Signed-off-by: Linas Vepstas <linas@linas.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:49:15 +0000 (18:49 -0600)]
[PATCH] ppc64: avoid PCI error reporting for empty slots
06-eeh-empty-slot-error.patch
Performing PCI config-space reads to empty PCI slots can lead to reports of
"permanent failure" from the firmware. Ignore permanent failures on empty slots.
Signed-off-by: Linas Vepstas <linas@linas.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:48:52 +0000 (18:48 -0600)]
[PATCH] ppc64: PCI error rate statistics
04-eeh-statistics.patch
This minor patch adds some statistics-gathering counters that allow the
behaviour of the EEH subsystem o be monitored. While far from perfect,
it does provide a rudimentary device that makes understanding of the
current state of the system a bit easier.
Signed-off-by: Linas Vepstas <linas@linas.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:48:45 +0000 (18:48 -0600)]
[PATCH] ppc64: PCI address cache minor fixes
03-eeh-addr-cache-cleanup.patch
This is a minor patch to clean up a buglet related to the PCI address cache.
(The buglet doesn't manifes itself unless there are also bugs elsewhere,
which is why its minor.). Also:
-- Improved debug printing.
-- Declare some private routines as static
-- Adds reference counting to struct pci_dn->pcidev structure
Signed-off-by: Linas Vepstas <linas@linas.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Linas Vepstas [Fri, 4 Nov 2005 00:47:50 +0000 (18:47 -0600)]
[PATCH] ppc64: misc minor cleanup
02-eeh-minor-cleanup.patch
This patch performs some minor cleanup of the eeh.c file, including:
-- trim some trailing whitespace
-- remove extraneous #includes
-- use the macro PCI_DN uniformly, instead of the void pointer chase.
-- typos in comments
-- improved debug printk's
Signed-off-by: Linas Vepstas <linas@linas.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] ppc64: Don't panic when early __ioremap fails
Early calls to __ioremap() will panic if the hash insertion fails. This
patch makes them return NULL instead. It happens with some pSeries users
who enabled CONFIG_BOOTX_TEXT. The later is getting an incorrect address
for the fame buffer and the hash insertion fails. With this patch, it
will display an error instead of crashing at boot.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olaf Hering [Wed, 9 Nov 2005 19:54:43 +0000 (20:54 +0100)]
[PATCH] ppc64 boot: fix compile warnings
Fix a few compile warnings
arch/ppc64/boot/addRamDisk.c:166: warning: int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:170: warning: int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:265: warning: unsigned int format, long unsigned int arg (arg 2)
arch/ppc64/boot/addRamDisk.c:302: warning: unsigned int format, long unsigned int arg (arg 3)
Signed-off-by: Olaf Hering <olh@suse.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olaf Hering [Wed, 9 Nov 2005 19:53:43 +0000 (20:53 +0100)]
[PATCH] ppc64 boot: remove sysmap from required filenames
A stripped vmlinux does not contain enough symbols to recreate the
System.map. The System.map file is only used to determine the end of
the runtime memory size. This is the same value (rounded up to
PAGE_SIZE) as ->memsiz in the ELF program header.
Also, the target vmlinux.initrd doesnt work in 2.6.14:
arch/ppc64/boot/addRamDisk arch/ppc64/boot/ramdisk.image.gz vmlinux.strip arch/ppc64/boot/vmlinux.initrd
Name of vmlinux output file missing.
Signed-off-by: Olaf Hering <olh@suse.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
Marcelo Tosatti [Wed, 9 Nov 2005 13:00:16 +0000 (11:00 -0200)]
[PATCH] fs_enet build fix
Due to the recent update of the platform code, some platform device
drivers fail to compile. This fix is for fs_enet, adding #include of a
new header, to which a number of platform stuff has been relocated.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Matt Porter [Wed, 9 Nov 2005 13:42:05 +0000 (06:42 -0700)]
[PATCH] ppc32: fix ppc44x fpu build
Fixes ppc44x fpu support that broke from a bad arch/powerpc merge.
Instead of adding KernelFP back in (which duplicates code) we use
the same kernel fpu unavailable handler as classic PPC processors.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Wed, 9 Nov 2005 02:38:01 +0000 (13:38 +1100)]
[PATCH] powerpc: Move various ppc64 files with no ppc32 equivalent to powerpc
This patch moves a bunch of files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
abs_addr.h
compat.h
lppaca.h
paca.h
tce.h
cpu_setup_power4.S
ioctl32.c
firmware.c
pacaData.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
- pacaData.c renamed paca.c to remove studlyCaps
- Misplaced { moved in lppaca.h
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Wed, 9 Nov 2005 02:04:06 +0000 (13:04 +1100)]
[PATCH] powerpc: Merge current.h
This patch merges current.h. This is a one-big-ifdef merge, but both
versions are so tiny, I think we can live with it. While we're at it,
we get rid of the fairly pointless redirection through get_current()
in the ppc64 version.
Built and booted on POWER5 LPAR (ARCH=powerpc & ARCH=ppc64). Built
for 32-bit pmac (ARCH=powerpc & ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Wed, 9 Nov 2005 00:21:07 +0000 (11:21 +1100)]
[PATCH] powerpc: Merge signal.h
Having already merged the ppc and ppc64 versions of signal.c, this
patch finishes the job by merging signal.h. The two versions were
almost identical already. Notable changes:
- We use BITS_PER_LONG to correctly size sigset_t
- Remove some uneeded #includes and struct forward
declarations. This does mean adding an include to signal_32.c which
relied on the indirect inclusion of sigcontext.h
- As the ppc64 version, the merged signal.h has prototypes for
do_signal() and do_signal32(). Thus remove extra prototypes from
ppc_ksyms.c which had them directly.
Built and booted on POWER5 LPAR (ARCH=ppc64 and ARCH=powerpc). Built
for 32-bit powermac (ARCH=ppc and ARCH=powerpc) and Walnut (ARCH=ppc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Andrew Morton [Wed, 9 Nov 2005 23:45:30 +0000 (15:45 -0800)]
[PATCH] powerpc: sched fixups
- Re-add a hunk lost during merge: ppc64 is missing the hunk that disables
preempt on the secondary CPUs before they call cpu_idle().
- ppc's cpu_idle() had the need_resched() test wrong.
Cc: Nick Piggin <nickpiggin@yahoo.com.au> CC: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Anton Blanchard <anton@samba.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chen, Kenneth W [Wed, 9 Nov 2005 23:45:29 +0000 (15:45 -0800)]
[PATCH] optimize activate_task()
recalc_task_prio() is called from activate_task() to calculate dynamic
priority and interactive credit for the activating task. For real-time
scheduling process, all that dynamic calculation is thrown away at the end
because rt priority is fixed. Patch to optimize recalc_task_prio() away
for rt processes.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com> Acked-by: Ingo Molnar <mingo@elte.hu> Cc: Nick Piggin <piggin@cyberone.com.au> Cc: Con Kolivas <kernel@kolivas.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ondrej Zary [Wed, 9 Nov 2005 23:25:15 +0000 (00:25 +0100)]
[PATCH] ide-floppy: software eject not working with LS-120 drive
The problem (eject not working on ATAPI LS-120 drive) is caused by
idefloppy_ioctl() function which *first* tries generic_ide_ioctl()
and *only* if it fails with -EINVAL, proceeds with the specific ioctls.
The generic eject command fails with something other than -EINVAL
and the specific one is never executed.
This patch fixes it by first going through the internal ioctls
and only trying generic_ide_ioctl() if none of them matches.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
[PATCH] siimage: enable interrupts on Adaptec SA-1210 card
The siimage driver proports to support the Adaptec SA-1210 SATA
controller. However, at least some of those cards boot-up with their
interrupts disabled internally. The siimage driver currently ignores
that fact, so that driver does not actually work with those cards.
This patch enables those interrupts on cards that need it.
[ This is implemented based on similar code in the libata-based
sata_sil driver. ]
Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Linus Torvalds [Wed, 9 Nov 2005 22:56:00 +0000 (14:56 -0800)]
Fix AGP compile on non-x86 architectures
AGP shouldn't use "global_flush_tlb()" to flush the AGP mappings, that i
spurely an x86'ism. The proper AGP mapping flusher that should be used
is "flush_agp_mappings()", which on x86 obviously happens to do a global
TLB flush.
This makes AGP (or at least the config _I_ happen to use) compile again
on ppc64.
Jordan Crouse [Wed, 9 Nov 2005 22:26:09 +0000 (23:26 +0100)]
[PATCH] ide: AMD Geode GX/LX support
From: "Jordan Crouse" <jordan.crouse@amd.com>
The core IDE engine on the CS5536 is the same as the other AMD southbridges,
so unlike the CS5535, we can simply add the appropriate PCI headers to
the existing amd74xx code.
Willem Riede [Wed, 9 Nov 2005 22:18:22 +0000 (23:18 +0100)]
[PATCH] ide: ide-scsi fails to call idescsi_check_condition for things like "Medium not present"
This patch started life as a response to fedora specific ide subsystem changes
that made error handling of my ATAPI tape drive fail; the specifics are in
The insertion of the statement rq->errors = err; near the end of
ide_end_drive_cmd() in drivers/ide/ide-io.c means that rq->errors does not
contain what it needs to in idescsi_end_request() in drivers/scsi/ide-scsi.c
anymore. Recent mainline kernels now also have this change.
The patch below makes ide-scsi whole.
Signed-off-by: Willem Riede <wrlk@riede.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Adrian Bunk [Wed, 9 Nov 2005 22:07:56 +0000 (23:07 +0100)]
[PATCH] ide: possible cleanups
This patch contains the following possible cleanups:
- pci/cy82c693.c: make a needlessly global function static
- remove the following unneeded EXPORT_SYMBOL's:
- ide-taskfile.c: do_rw_taskfile
- ide-iops.c: default_hwif_iops
- ide-iops.c: default_hwif_transport
- ide-iops.c: wait_for_ready
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Hannes Reinecke [Wed, 9 Nov 2005 21:47:18 +0000 (22:47 +0100)]
[PATCH] ide: incorrect device link for ide-cs
Devices driven by ide-cs will appear under /sys/devices instead of the
appropriate PCMCIA device. To fix this I had to extend the hw_regs_t
structure with a 'struct device' field, which allows us to set the
parent link for the appropriate hwif.
[NETFILTER] ctnetlink: ICMP_ID is u_int16_t not u_int8_t.
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER] ctnetlink: Fix oops when no ICMP ID info in message
This patch fixes an userspace triggered oops. If there is no ICMP_ID
info the reference to attr will be NULL.
Signed-off-by: Krzysztof Piotr Oledzki <ole@ans.pl> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER] ctnetlink: Add support to identify expectations by ID's
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER] ctnetlink: propagate error instaed of returning -EPERM
Propagate the error to userspace instead of returning -EPERM if the get
conntrack operation fails.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[NETFILTER] ctnetlink: return -EINVAL if size is wrong
Return -EINVAL if the size isn't OK instead of -EPERM.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Harald Welte <laforge@netfilter.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log