Al Viro [Mon, 16 May 2005 00:59:55 +0000 (01:59 +0100)]
[SCSI] TYPE_RBC cache fixes (sbp2.c affected)
a) TYPE_SDAD renamed to TYPE_RBC and taken to scsi.h
b) in sbp2.c remapping of TYPE_RPB to TYPE_DISK turned off
c) relevant places in midlayer and sd.c taught to accept TYPE_RBC
d) sd.c::sd_read_cache_type() looks into page 6 when dealing with
TYPE_RBC - these guys have writeback cache flag there and are not guaranteed
to have page 8 at all.
e) sd_read_cache_type() got an extra sanity check - it checks that
it got the page it asked for before using its contents. And screams if
mismatch had happened. Rationale: there are broken devices out there that
are "helpful" enough to go for "I don't have a page you've asked for, here,
have another one". For example, PL3507 had been caught doing just that...
f) sbp2 sets sdev->use_10_for_rw and sdev->use_10_for_ms instead
of bothering to remap READ6/WRITE6/MOD_SENSE, so most of the conversions
in there are gone now.
Incidentally, I wonder if USB storage devices that have no
mode page 8 are simply RBC ones. I haven't touched that, but it might
be interesting to check...
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Matthew Wilcox [Fri, 20 May 2005 18:15:43 +0000 (19:15 +0100)]
[SCSI] sym2 version 2.2.1
sym2 version 2.2.1:
- Fix MMIO BAR detection (Thanks to Bob Picco)
- Fix odd-sized transfers with a wide bus (Thanks to Larry Stephens)
- Write posting fixes (Thanks to Thibaut Varene)
- Change one of the GFP_KERNEL allocations back into a GFP_ATOMIC
- Make CCB_BA() return a script-endian address
- Move range checks and disabling of devices from the queuecommand path
to slave_alloc()
- Remove a warning in sym_setup_cdb()
- Keep a pointer to the scsi_target instead of the scsi_dev in the tcb
- Remove a check for the upper layers passing an oversized cmd
- Replace CAM_REQ_ constants with the Linux DID_ constants
- Replace CAM_DIR_ constants with the Linux DMA_ constants
- Inline sym_read_parisc_pdc() on non-parisc systems
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New code from the Adaptec driver. Performance enhancement for newer
adapters. I hope that this isn't too big for a single patch. I believe
that other than the few small cleanups mentioned, that the changes are
all related.
- Added Variable FIB size negotiation for new adapters.
- Added support to maximize scatter gather tables and thus permit
requests larger than 64KB/each.
- Limit Scatter Gather to 34 elements for ROMB platforms.
- aac_printf is only enabled with AAC_QUIRK_34SG
- Large FIB ioctl support
- some minor cleanup
Passes sparse check.
I have tested it on x86 and ppc64 machines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] saved and restore result for timed out commands
Save and restore the scmd->result, so that timed out commands do not
return the result of the TEST UNIT READY or the start/stop commands. Code
is already in place to save and restore the result for the request sense
case.
The previous version of this patch erroneously removed the "if" check,
instead add a comment as to why the "if" is needed.
Signed-off-by: Patrick Mansfield <patmans@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Tejun Heo [Fri, 13 May 2005 15:46:08 +0000 (00:46 +0900)]
[SCSI] remove a timer race in scsi_queue_insert()
scsi_queue_insert() has four callers. Three callers call with
timer disabled and one (the second invocation in
scsi_dispatch_cmd()) calls with timer activated.
scsi_queue_insert() used to always call scsi_delete_timer()
and ignore the return value. This results in race with timer
expiration. Remove scsi_delete_timer() call from
scsi_queue_insert() and make the caller delete timer and check
the return value.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] ipr: Fix ipr PCI hotplug hang with CDROM attach
Currently, during PCI hotplug remove, if the upper layer
drivers of the attached devices send commands down as part
of the remove action, like a CDROM, the hotplug action
will hang forever due to the ipr driver returning
SCSI_MLQUEUE_HOST_BUSY. Patch fixes this.
Signed-off-by: Brian King <brking@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Kai Makisara [Sun, 1 May 2005 15:11:55 +0000 (18:11 +0300)]
[SCSI] SCSI tape: fix permissions for SG_IO, etc.
This patch is against 2.6.12-rc3 + linus-patch from April 30. The patch
contains the following fixes:
- CAP_SYS_RAWIO is used instead of CAP_SYS_ADMIN; fix from Alan Cox
- only direct sending of SCSI commands requires this permission
- the st status is modified is successful unload is performed using
SCSI_IOCTL_STOP_UNIT
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 27 Apr 2005 13:05:51 +0000 (06:05 -0700)]
[SCSI] aacraid: remove sparse warnings
This patch addresses the sparse -Wbitwise warnings that Christoph wanted
me to eliminate. This mostly consisted of making data structure
elements of hardware associated structures the __le* equivalent.
Although there were a couple places where there was mixing of cpu and le
variable math. These changes have been tested on both an x86 and ppc
machine running bonnie++. The usage of the LE32_ALL_ONES macro has been
eliminated.
Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/scsi/dpt_i2o.c: In function ‘adpt_isr’:
drivers/scsi/dpt_i2o.c:2030: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2031: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2042: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2043: warning: passing argument 2 of ‘writel’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2046: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2048: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2055: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2062: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2069: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c: In function ‘adpt_i2o_to_scsi’: drivers/scsi/dpt_i2o.c:2239: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2243: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2248: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
drivers/scsi/dpt_i2o.c:2259: warning: passing argument 1 of ‘readl’ makes pointer from integer without a cast
It define variables which are only used with a type of 'void __iomem *'
with this type instead of the incorrect 'unsigned long' type.
It also remove pointless casts.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch contains cleanups including the following:
- remove #ifdef'ed code for other OS's
- remove other unused code
- make needlessly global code static
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] make scsi_queue_insert() use blk_requeue_request()
scsi_queue_insert() used to use blk_insert_request() for requeueing
requests. This depends on the unobvious behavior of
blk_insert_request() setting REQ_SPECIAL and REQ_SOFTBARRIER when
requeueing. This patch makes scsi_queue_insert() use
blk_requeue_request(). As REQ_SPECIAL means special requests and
REQ_SOFTBARRIER is automatically handled by blk layer now, no flag
needs to be set.
Note that scsi_queue_insert() now calls scsi_run_queue() itself, and
the prototype of the function is added right above
scsi_queue_insert(). This is temporary, as later requeue path
consolidation patchset removes scsi_queue_insert(). By adding
temporary prototype, we can do away with unnecessarily moving
functions.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] make scsi_requeue_request() use blk_requeue_request()
scsi_requeue_request() used to use blk_insert_request() for requeueing
requests. This depends on the unobvious behavior of
blk_insert_request() setting REQ_SPECIAL and REQ_SOFTBARRIER when
requeueing. This patch makes scsi_queue_insert() use
blk_requeue_request(). As REQ_SPECIAL means special requests and
REQ_SOFTBARRIER is automatically handled by blk layer now, no flag
needs to be set.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] remove requeue feature from blk_insert_request()
blk_insert_request() has a unobivous feature of requeuing a
request setting REQ_SPECIAL|REQ_SOFTBARRIER. SCSI midlayer
was the only user and as previous patches removed the usage,
remove the feature from blk_insert_request(). Only special
requests should be queued with blk_insert_request(). All
requeueing should go through blk_requeue_request().
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_init_io() used to set REQ_SPECIAL when it fails sg
allocation before requeueing the request by returning
BLKPREP_DEFER. REQ_SPECIAL is being updated to mean special
requests. So, remove REQ_SPECIAL setting.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] make blk layer set REQ_SOFTBARRIER on defer and requeue
This is the reworked version of the patch. It sets REQ_SOFTBARRIER
in two places - in elv_next_request() on BLKPREP_DEFER and in
blk_requeue_request().
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The fusion Kconfig forgets to set CONFIG_FUSION, which is required to
get the upper makefile to descend into the fusion directory. Add this
back as a variable and make the two upper level modules select it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
(1) mptfc.c: This driver is having module_init, module_exit, and probe.
(2) mptfc.c: Registering for Fibre Channel pci ids are done from this
module.
(3) mptfc.c: Convert MODULE_PARM to module_param
Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
(1) mptspi.c: This driver is having module_init, module_exit, and probe.
(2) mptspi.c: Registering for SCSI pci ids are done from this module.
(3) mptspi.c: Convert MODULE_PARM to module_param
Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
(1) mptscsih.c: Remove credits, -sralston references , update copyright
(2) mptscsih.c: split driver support
(3) mptscsih.c: module_init, module_exit, and probe routines moved to new
stub drivers, mptfc and mptspi
(4) mptscsih.c: some global parameters are moved to MPT_SCSI_HOST
(5) mptscsih.c: removed scsi_device_online check.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] mptfusion: Kconfig Adding new bus type drivers for fusion drivers.
(1) Kconfig - added new mptspi and mptfc scsi lld drivers
(2) Kconfig - increased MAX_SGE from 40 to 128
(2) Makefile - compilation support for split drivers
(3) Makefile - cleaned up debug defines; e.g. removed obsolete, added others
Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Both drivers are marked broken and haven't compiled since very early
2.5.x. And they're for IDE hardware so they shouldn't have been
written to the SCSI layer at all.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Jeff Dike [Sat, 7 May 2005 04:30:55 +0000 (21:30 -0700)]
[PATCH] uml: x86_64 fixes
This fixes some x86_64 bugs -
- maybe_map returns -1 on error instead of 0, which is interpreted as
physical address 0
- removed an include of ipc.h, which isn't needed
- fixed the calculation of signal frame location
- the signal delivery code is now immune to the stack expansion check
- added a missing include
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 7 May 2005 04:30:54 +0000 (21:30 -0700)]
[PATCH] uml: Fix process exit race
tt-mode closes switch_pipes in exit_thread_tt and kills processes in
switch_to_tt, if the exit_state is EXIT_DEAD or EXIT_ZOMBIE.
In very rare cases the exiting process can be scheduled out after having set
exit_state and closed switch_pipes (from release_task it calls proc_pid_flush,
which might sleep). If this process is to be restarted, UML failes in
switch_to_tt with:
write of switch_pipe failed, err = 9
We fix this by closing switch_pipes not in exit_thread_tt, but later in
release_thread_tt. Additionally, we set switch_pipe[0] = 0 after closing.
switch_to_tt must not kill "from" process depending on its exit_state, but
must kill it after release_thread was processed only, so it examines
switch_pipe[0] for its decision.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 7 May 2005 04:30:52 +0000 (21:30 -0700)]
[PATCH] uml: Use CONFIG variable for address space size
tt/mem.c still uses hardcoded TOP for i386 instead of CONFIG_TOP_ADDR provided
by subarch's Kconfig_XXXX, which would be right.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 7 May 2005 04:30:51 +0000 (21:30 -0700)]
[PATCH] uml: Turn literal numbers into symbolic constants
So, there I was, looking at my own code, wondering what the magic setjmp
return values did. This patch turns the constants that are used to make
requests of the initial thread into meaningful symbols.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 7 May 2005 04:30:51 +0000 (21:30 -0700)]
[PATCH] uml: Makefile cleanup
This eliminates some stuff from arch/um/kernel/Makefile which refers to a
file which has long since been deleted.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 7 May 2005 04:30:50 +0000 (21:30 -0700)]
[PATCH] uml: Eliminate unusable function
Eliminate the non-inline version of switch_mm, which can't be used,
considering the inline version in asm/mmu_context.h
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 7 May 2005 04:30:49 +0000 (21:30 -0700)]
[PATCH] uml: S390 preparation, save an extra register
s390 tt-mode needs to save not only syscall number, but an further register
also.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bodo Stroesser [Sat, 7 May 2005 04:30:46 +0000 (21:30 -0700)]
[PATCH] uml: S390 preparation, peekusr/pokeusr defined by subarch
s390 needs to change some parts of arch/um/kernel/ptrace.c. Thus, the code
regarding PEEKUSER and POKEUSER are shifted to arch/um/sys-<subarch>/ptrace.c.
Also s390 debug registers need to be updated, when singlestepping is switched
on / off. Thus, setting/resetting of singlestepping is centralized in the new
function set_singlestep(), which also inserts the macro
SUBARCH_SET_SINGLESTEP(mode), if defined.
Finally, s390 has the "ieee_instruction_pointer" in its
registers, which also is allowed to be read via
To implement this feature, sys_ptrace inserts the macro
SUBARCH_PTRACE_SPECIAL, if defined.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 7 May 2005 04:30:45 +0000 (21:30 -0700)]
[PATCH] uml: command line handling cleanup
Command line handling cleanups - a couple of things made static and an
unused declaration removed from header.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 7 May 2005 04:30:44 +0000 (21:30 -0700)]
[PATCH] uml: Remove include/asm-um/elf.h
I accidentally included include/asm-um/elf.h as a real file in a previous
patch. This patch eliminates it.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sat, 7 May 2005 04:30:43 +0000 (21:30 -0700)]
[PATCH] uml: __deprecated makes build unnecessarily noisy
Remove the __deprecated from verify_area_skas and verify_area_tt. Since
verify_area is itself marked __deprecated, and it is the only caller of
these, then they don't need to be marked. Marking them only makes the
build noisier.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jiri Benc [Sat, 7 May 2005 04:30:42 +0000 (21:30 -0700)]
[PATCH] video/tuner: add VIDEO_G_FREQUENCY and freq range to VIDIOC_G_TUNER
This patch adds a VIDIOC_G_FREQUENCY command to tuner-core.c and sets
lowest and highest tunable frequencies in v4l2_tuner structure returned by
VIDIOC_G_TUNER command.
Jiri Benc [Sat, 7 May 2005 04:30:42 +0000 (21:30 -0700)]
[PATCH] video/tuner: fix tuner->freq updating
In VIDIOC_S_FREQUENCY command in tuner-core.c, t->freq is set to a new
value before calling set_freq(). This is not necessary, as set_freq() sets
t->freq itself. Moreover, it causes problems with Philips tuners, as they
need to take into consideration difference between previous and new
frequency.
Kumar Gala [Sat, 7 May 2005 04:30:41 +0000 (21:30 -0700)]
[PATCH] ppc32: Fix POWER3/POWER4 compiler error
In separating out support for hardware floating point we missed the fact
that both POWER3 and POWER4 have HW FP. Enable CONFIG_PPC_FPU for POWER3
and POWER4 fixes the issue.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com> Acked-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Mackerras [Sat, 7 May 2005 00:41:03 +0000 (17:41 -0700)]
[PATCH] ppc64: enable CONFIG_RTAS_PROC by default
This patch enables CONFIG_RTAS_PROC by default on pSeries. This will
preserve /proc/ppc64/rtas/rmo_buffer, which is needed by librtas.
Signed-off-by: John Rose <johnrose@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Sat, 7 May 2005 00:41:01 +0000 (17:41 -0700)]
[PATCH] revert msdos partitioning fix
This change from March 3rd causes the partition parsing code to ignore
partitions which have a signature byte of zero. Turns out that more people
have such partitions than we expected, and their device numbering is coming up
wrong in post-2.6.11 kernels.
So revert the change while we think about the problem a bit more.
James Bottomley [Fri, 6 May 2005 18:14:48 +0000 (13:14 -0500)]
[SCSI] correct the sym2 period setting routines
There's a slight bug in the routines in that if the period requires dt,
then the routine will unconditionally set it. DT may only be set if
Wide is also set, so this turns back on the wide bit.
For domain validation to work correctly, we need to observe the wide bit
absolutely.
Acked by: Matthew Wilcox <willy@debian.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Jens Axboe [Fri, 6 May 2005 06:37:44 +0000 (08:37 +0200)]
[PATCH] fix alsa via82xx resume
Trying software suspend on my workstation makes it crash on resume. The
problem is that via82xx marks the chip_init function as _devinit, but calls
it on resume as well.
Paul Mackerras [Fri, 6 May 2005 06:28:56 +0000 (16:28 +1000)]
[PATCH] ppc64: global interrupt queue cleanup
Move the code to set global interrupt queue membership to xics.c,
and remove no longer needed extern declarations. Also call it on
all cpus (even the boot cpu) to prepare for kexec.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: R Sharada <sharada@in.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trivial patch to remove our last direct reference to contig_page_data.
This will make it just that much less hard to seperate NUMA and
DISCONTIG. Please forward on. Against 2.6.12-rc1
Signed-off-by: Joel Schopp <jschopp@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Mackerras [Fri, 6 May 2005 04:27:17 +0000 (14:27 +1000)]
[PATCH] ppc64: remove asm/bootinfo.h include
The defines in bootinfo.h are not used, so the include can be removed.
According to Ben, birecs are not used on ppc64:
on ppc64, we made the decision of enforcing the presence of an
OF device-tree and either an OF-like client interface or a kexec
like flattened tree.
so if your bootloader want to say things to the kernel,
it can do so by adding properties to the device-tree
compile-tested with defconfig
Signed-off-by: Olaf Hering <olh@suse.de> Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Mackerras [Fri, 6 May 2005 03:35:04 +0000 (13:35 +1000)]
[PATCH] ppc64: fix reloc_offset comment
The code in reloc_offset is actually subtracting the address in the link
register from the address calculated by the linker. Perhaps the
extended mnemonic `sub' replaced an original `subf' and the comment just
did not get updated.
Paul Mackerras [Fri, 6 May 2005 03:29:34 +0000 (13:29 +1000)]
[PATCH] ppc64: fix prom.c compile warning
The code in unflatten_device_tree knows that get_property is written to
only return with lenp equal to 1 when also returning a valid pointer.
The gcc 3.3.3 compiler is not able to prove this to itself, so it warns
about a possible uninitialized pointer dereference:
.../arch/ppc64/kernel/prom.c: In function `unflatten_device_tree':
.../arch/ppc64/kernel/prom.c:828:
warning: `p' might be used uninitialized in this function
Unless it is desired to rework the interaction between the two
functions, this will keep the existing behavior but quiet the compiler.
Adrian Bunk [Thu, 5 May 2005 23:16:22 +0000 (16:16 -0700)]
[PATCH] drivers/scsi/sym53c416.c: fix a wrong check
The Coverity checker found that this for loop was wrong.
This patch changes it to what seems to be intended.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: James Bottomley <James.Bottomley@steeleye.com> Cc: Matthew Wilcox <willy@debian.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Domen Puncer [Thu, 5 May 2005 23:16:19 +0000 (16:16 -0700)]
[PATCH] fix lib/sort regression test
The regression test in lib/sort.c is currently worthless because the array
that is generated for sorting will be all zeros. This patch fixes things
so that the array that is generated will contain unsorted integers (that
are not all identical) as was probably intended.
Signed-off-by Daniel Dickman <didickman@yahoo.com> Signed-off-by: Domen Puncer <domen@coderock.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Domen Puncer [Thu, 5 May 2005 23:16:15 +0000 (16:16 -0700)]
[PATCH] CodingStyle: trivial whitespace fixups
When I do a "diff -Nur arch/i386 arch/x86_64" to see what is different between these two
architectures, I see some differences due to whitespace issues only. The attached patch removes
some of the noise by fixing up the following files:
- arch/i386/boot/bootsect.S
- arch/i386/boot/video.S
- arch/x86_64/boot/bootsect.S
Signed-off-by: Daniel Dickman <didickman@yahoo.com> Signed-off-by: Domen Puncer <domen@coderock.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Domen Puncer [Thu, 5 May 2005 23:16:13 +0000 (16:16 -0700)]
[PATCH] ixj* - compile warning cleanup
compile warning cleanup - suggested by Adrian Bunk; remove unmaintained rcs
char strings from source and handle the occurrences of their use, make sure
kernel-userspace issues taken care of; break out into separate patch
Signed-off-by: Stephen Biggs <yrgrknmxpzlk@gawab.com> Signed-off-by: Domen Puncer <domen@coderock.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adrian Bunk [Thu, 5 May 2005 23:16:09 +0000 (16:16 -0700)]
[PATCH] make some things static
This patch makes some needlessly global identifiers static.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Acked-by: Arjan van de Ven <arjanv@infradead.org> Acked-by: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6 / log