[POWERPC] Fix PowerPC 750CL and 750GX CPU features
PowerPC 750CL has high BATs. The patch below adds a CPU_FTRS_750CL that
includes that. Without it, the original firmware mappings in the high BATs
aren't cleared which continue to override the linux translations.
It also adds CPU_FTR_COMMON to CPU_FTRS_750GX for completeness.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Will Schmidt [Tue, 17 Apr 2007 14:44:46 +0000 (00:44 +1000)]
[POWERPC] hvc_console: Polling mode timer backoff
Add a back-off mechanism to hvc_console's polling logic. This change
drops the timers/second ratio from ~90 to ~1/2 while the console is
idle.
This change is most noticeable when watching /proc/timer_stats output.
This only affects when the hvc_console is running in poll mode, i.e.
power4 and cell systems.
I've tested on Power4, Michael Ellerman has both contributed to the
patch and tested on cell.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com> Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Acked-by: Linas Vepstas <linas@austin.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Tue, 24 Apr 2007 03:57:12 +0000 (13:57 +1000)]
[POWERPC] Partially revert "Add correct interrupt property for pegasos ide"
It turns out that commit e48059225c2edc6f1e5a2008261f1efdf606f247
breaks some existing systems that use the via82cxxx driver. This
reverts the change to via82cxxx.c.
Jeremy Kerr [Mon, 23 Apr 2007 19:35:47 +0000 (21:35 +0200)]
[POWERPC] cell: enable RTAS-based PTCAL for Cell XDR memory
Enable Periodic Recalibration (PTCAL) support for Cell XDR memory,
using the new ibm,cbe-start-ptcal and ibm,cbe-stop-ptcal RTAS calls.
Tested on QS20 and QS21 (by Thomas Huth). It seems that SLOF has
problems disabling, at least on QS20; this patch should only be
used once these problems have been addressed.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Christian Krafft [Mon, 23 Apr 2007 19:35:46 +0000 (21:35 +0200)]
[POWERPC] cell: add support for proper device-tree
This patch adds support for a proper device-tree.
A porper device-tree on cell contains be nodes
for each CBE containg nodes for SPEs and all the
other special devices on it.
Ofcourse oldschool devicetree is still supported.
Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Christian Krafft [Mon, 23 Apr 2007 19:35:45 +0000 (21:35 +0200)]
[POWERPC] add of_iomap function
The of_iomap function maps memory for a given
device_node and returns a pointer to that memory.
This is used at some places, so it makes sense to
a seperate function.
Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Christian Krafft [Mon, 23 Apr 2007 19:35:44 +0000 (21:35 +0200)]
[POWERPC] pmi probe device by device-type
At the moment the pmi device driver is probing for devices with
a given type and a given name. As there may be devices of
the same type but with a different name, probing should be
done also for device type only.
Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Christian Krafft [Mon, 23 Apr 2007 19:35:43 +0000 (21:35 +0200)]
[POWERPC] add check for initialized driver data to pmi driver
This patch adds a check for the private driver data to be initialized.
The bug showed up, as the caller found a pmi device by it's type.
Whereas the pmi driver probes for the type and the name.
Since the name was not as the driver expected, it did not initialize.
A more relaxed probing will be supplied with an extra patch, too.
Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Christian Krafft [Mon, 23 Apr 2007 19:35:42 +0000 (21:35 +0200)]
[POWERPC] cell: use pmi in cpufreq driver
The new PMI driver was added in order to support
cpufreq on blades that require the frequency to
be controlled by the service processor, so use it
on those.
Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Christian Krafft [Mon, 23 Apr 2007 19:35:41 +0000 (21:35 +0200)]
[POWERPC] cbe_thermal: add throttling attributes to cpu and spu nodes
This patch adds some attributes the cpu and spu nodes:
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_begin
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_end
/sys/devices/system/[c|s]pu/[c|s]pu*/thermal/throttle_full_stop
Signed-off-by: Christian Krafft <krafft@de.ibm.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Jeremy Kerr [Mon, 23 Apr 2007 19:08:29 +0000 (21:08 +0200)]
[POWERPC] spu_base: fix initialisation on systems with no SPEs
This change fixes the case where spu_base and spufs are initialised on a
system with no SPEs - unconditionally create the spu_lists so spu_alloc
doesn't explode, and check for spu_management ops before starting spufs.
spu_base.c is always built into the kernel image, so there is no need
for a cleanup function. And some of the things it does are in the
way for my following patches, so I'd rather get rid of it ASAP.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
- remove the spu_acquire_runnable from spu_run_init. I need to
opencode it in spufs_run_spu in the next patch
- remove various inline attributes, we don't really want to inline
long functions with multiple callsites
- cleanup return values and runcntl_write calls in spu_run_init
- use normal kernel codingstyle in spu_reacquire_runnable
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Akinobu Mita [Mon, 23 Apr 2007 19:08:26 +0000 (21:08 +0200)]
[POWERPC] spufs: enable SPU coredump for kernel-builtin spufs
spu_coredump_calls.owner is NULL in case of a builtin spufs,
so the checks in here break.
Check for the availability of the spu_coredump_calls variable
instead.
Akinobu Mita [Mon, 23 Apr 2007 19:08:22 +0000 (21:08 +0200)]
[POWERPC] spufs: use memcpy_fromio() to copy from local store
GCC may generates inline copy loop to handle memcpy() function
instead of kernel defined memcpy(). But this inlined version of memcpy()
causes an alignment interrupt when copying from local store.
This patch uses memcpy_fromio() and memcpy_toio to copy local store
to prevent memcpy() being inlined.
Signed-off-by: Akinobu Mita <mita@fixstars.com> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Akinobu Mita [Mon, 23 Apr 2007 19:08:19 +0000 (21:08 +0200)]
[POWERPC] spufs: fix missing error handling in module_init()
spufs module_init forgot to call a few cleanup functions
on error path. This patch also includes cosmetic changes in
spu_sched_init() (identation fix and return error code).
[modified by hch to apply ontop of the latest schedule changes]
Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Akinobu Mita <mita@fixstars.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
[POWERPC] spufs: make spu page faults not block scheduling
Until now, we have always entered the spu page fault handler
with a mutex for the spu context held. This has multiple
bad side-effects:
- it becomes impossible to suspend the context during
page faults
- if an spu program attempts to access its own mmio
areas through DMA, we get an immediate livelock when
the nopage function tries to acquire the same mutex
This patch makes the page fault logic operate on a
struct spu_context instead of a struct spu, and moves it
from spu_base.c to a new file fault.c inside of spufs.
We now also need to copy the dar and dsisr contents
of the last fault into the saved context to have it
accessible in case we schedule out the context before
activating the page fault handler.
Luke Browning [Mon, 23 Apr 2007 19:08:13 +0000 (21:08 +0200)]
[POWERPC] spu sched: make addition to stop_wq and runque atomic vs wakeup
Addition to stop_wq needs to happen before adding to the runqeueue and
under the same lock so that we don't have a race window for a lost
wake up in the spu scheduler.
Signed-off-by: Luke Browning <lukebrowning@us.ibm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
[POWERPC] spufs: streamline locking for isolated spu setup
For quite a while now spu state is protected by a simple mutex instead
of the old rw_semaphore, and this means we can simplify the locking
around spu_setup_isolated a lot.
Instead of doing an spu_release before entering spu_setup_isolated and
then calling the complicated spu_acquire_exclusive we can now simply
enter the function locked an in guaranteed runnable state, so that the
only bit of spu_acquire_exclusive that's left is the call to
spu_unmap_mappings.
Similarly there's no more need to unlock and reacquire the state_mutex
when spu_setup_isolated is done, but we can always return with the
lock held and only drop it in spu_run_init in the failure case.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
[POWERPC] spufs: remove woken threads from the runqueue early
A single context should only be woken once, and we should not have
more wakeups for a given priority than the number of contexts on
that runqueue position.
Also add some asserts to trap future problems in this area more
easily.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
[POWERPC] spu sched: ensure preempted threads are put back on the runqueue, part2
To not lose a spu thread we need to make sure it always gets put back
on the runqueue. In find_victim aswell as in the scheduler tick as done
in the previous patch.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
[POWERPC] spufs: clear mapping pointers after last close
Make sure the pointers to various mappings are cleared once the last
user stopped using them. This avoids accessing freed memory when
tearing down the gang directory aswell as optimizing away
pte invalidations if no one uses these.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
[POWERPC] spufs: use cancel_rearming_delayed_workqueue when stopping spu contexts
The scheduler workqueue may rearm itself and deadlock when we try to stop
it. Put a flag in place to avoid skip the work if we're tearing down
the context.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Paul Mackerras [Fri, 13 Apr 2007 00:46:21 +0000 (10:46 +1000)]
[POWERPC] Fix detection of loader-supplied initrd on OF platforms
Commit 79c8541924a220964f9f2cbed31eaa9fdb042eab introduced code to move
the initrd if it was in a place where it would get overwritten by the
kernel image. Unfortunately this exposed the fact that the code that
checks whether the values passed in r3 and r4 are intended to indicate
the start address and size of an initrd image was not as thorough as the
kernel's checks. The symptom is that on OF-based platforms, the
bootwrapper can cause an exception which causes the system to drop back
into OF.
Previously it didn't matter so much if the code incorrectly thought that
there was an initrd, since the values for start and size were just passed
through to the kernel. Now the bootwrapper needs to apply the same checks
as the kernel since it is now using the initrd data itself (in the process
of copying it if necessary). This adds the code to do that.
Kumar Gala [Thu, 12 Apr 2007 23:01:34 +0000 (18:01 -0500)]
[POWERPC] Miscellaneous arch/powerpc Kconfig and platform/Kconfig cleanup
* Cleaned up some whitespace in arch/powerpc/Kconfig
* Moved sourcing of platforms/embedded6xx/Kconfig into platform/Kconfig
* Moved sourcing of platforms/4xx/Kconfig into platform/Kconfig and disabled it
* Removed EMBEDDEDBOOT since its not supported in arch/powerpc
* Removed PC_KEYBOARD since its not used anywhere
* Moved a few CONFIG options around in platform/Kconfig
* Moved interrupt controllers into platform/Kconfig out of bus section
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Joachim Fenkes [Thu, 22 Mar 2007 16:00:46 +0000 (17:00 +0100)]
[POWERPC] ibmebus: change probe/remove interface from using loc-code to DT path
In some cases, multiple OFDT nodes might share the same location code, so
the location code is not a unique identifier for an OFDT node. Changed the
ibmebus probe/remove interface to use the DT path of the device node instead
of the location code.
The DT path must be written into probe/remove right as it would appear in
the "devspec" attribute of the ebus device: relative to the DT root, with a
leading slash and without a trailing slash. One trailing newline will not
hurt; multiple newlines will (like perl's chomp()).
Example:
Add a device "/proc/device-tree/foo@12345678" to ibmebus like this:
echo /foo@12345678 > /sys/bus/ibmebus/probe
Remove the device like this:
echo /foo@12345678 > /sys/bus/ibmebus/remove
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Here's an implementation of DEBUG_PAGEALLOC for 64 bits powerpc.
It applies on top of the 32 bits patch.
Unlike Anton's previous attempt, I'm not using updatepp. I'm removing
the hash entries from the bolted mapping (using a map in RAM of all the
slots). Expensive but it doesn't really matter, does it ? :-)
Memory hot-added doesn't benefit from this unless it's added at an
address that is below end_of_DRAM() as calculated at boot time.
Here's an implementation of DEBUG_PAGEALLOC for ppc32. It disables BAT
mapping and is only tested with Hash table based processor though it
shouldn't be too hard to adapt it to others.
[POWERPC] Fix 32-bit mm operations when not using BATs
On hash table based 32 bits powerpc's, the hash management code runs with
a big spinlock. It's thus important that it never causes itself a hash
fault. That code is generally safe (it does memory accesses in real mode
among other things) with the exception of the actual access to the code
itself. That is, the kernel text needs to be accessible without taking
a hash miss exceptions.
This is currently guaranteed by having a BAT register mapping part of the
linear mapping permanently, which includes the kernel text. But this is
not true if using the "nobats" kernel command line option (which can be
useful for debugging) and will not be true when using DEBUG_PAGEALLOC
implemented in a subsequent patch.
This patch fixes this by pre-faulting in the hash table pages that hit
the kernel text, and making sure we never evict such a page under hash
pressure.
The 32 bits map_page() function is used internally by the mm code
for early mmu mappings and for ioremap. It should never be called
for an address that already has a valid PTE or hash entry, so we
add a BUG_ON for that and remove the useless flush_HPTE call.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/mm/pgtable_32.c | 9 ++++++---
1 file changed, 6 insertions(+), 3 deletions(-) Signed-off-by: Paul Mackerras <paulus@samba.org>
The current tlb flush code on powerpc 64 bits has a subtle race since we
lost the page table lock due to the possible faulting in of new PTEs
after a previous one has been removed but before the corresponding hash
entry has been evicted, which can leads to all sort of fatal problems.
This patch reworks the batch code completely. It doesn't use the mmu_gather
stuff anymore. Instead, we use the lazy mmu hooks that were added by the
paravirt code. They have the nice property that the enter/leave lazy mmu
mode pair is always fully contained by the PTE lock for a given range
of PTEs. Thus we can guarantee that all batches are flushed on a given
CPU before it drops that lock.
We also generalize batching for any PTE update that require a flush.
Batching is now enabled on a CPU by arch_enter_lazy_mmu_mode() and
disabled by arch_leave_lazy_mmu_mode(). The code epects that this is
always contained within a PTE lock section so no preemption can happen
and no PTE insertion in that range from another CPU. When batching
is enabled on a CPU, every PTE updates that need a hash flush will
use the batch for that flush.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Make the alignment exception handler use the new _inatomic variants
of __get/put_user. This fixes erroneous warnings in the very rare
cases where we manage to have copy_tofrom_user_inatomic() trigger
an alignment exception.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/kernel/align.c | 56 ++++++++++++++++++++++++--------------------
1 file changed, 31 insertions(+), 25 deletions(-) Signed-off-by: Paul Mackerras <paulus@samba.org>
Olaf Hering [Wed, 4 Apr 2007 16:20:04 +0000 (18:20 +0200)]
[POWERPC] Add correct interrupt property for pegasos ide
The firmware assigns irq 20/21 to the VIA IDE device on Pegasos.
But the required interrupt is 14/15.
Maybe someone confused decimal vs. hexadecimal values.
Signed-off-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Rename get_property to of_get_property: the last one
This also fixes a bug where a property value was being modified
in place.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Rename get_property to of_get_property: drivers
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Rename get_property to of_get_property: sound
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Rename get_property to of_get_property: arch/powerpc
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Rename get_property to of_get_property: include
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Tue, 3 Apr 2007 11:24:02 +0000 (21:24 +1000)]
[POWERPC] Allow drivers to map individual 4k pages to userspace
Some drivers have resources that they want to be able to map into
userspace that are 4k in size. On a kernel configured with 64k pages
we currently end up mapping the 4k we want plus another 60k of
physical address space, which could contain anything. This can
introduce security problems, for example in the case of an infiniband
adaptor where the other 60k could contain registers that some other
program is using for its communications.
This patch adds a new function, remap_4k_pfn, which drivers can use to
map a single 4k page to userspace regardless of whether the kernel is
using a 4k or a 64k page size. Like remap_pfn_range, it would
typically be called in a driver's mmap function. It only maps a
single 4k page, which on a 64k page kernel appears replicated 16 times
throughout a 64k page. On a 4k page kernel it reduces to a call to
remap_pfn_range.
The way this works on a 64k kernel is that a new bit, _PAGE_4K_PFN,
gets set on the linux PTE. This alters the way that __hash_page_4K
computes the real address to put in the HPTE. The RPN field of the
linux PTE becomes the 4k RPN directly rather than being interpreted as
a 64k RPN. Since the RPN field is 32 bits, this means that physical
addresses being mapped with remap_4k_pfn have to be below 2^44,
i.e. 0x100000000000.
The patch also factors out the code in arch/powerpc/mm/hash_utils_64.c
that deals with demoting a process to use 4k pages into one function
that gets called in the various different places where we need to do
that. There were some discrepancies between exactly what was done in
the various places, such as a call to spu_flush_all_slbs in one case
but not in others.
Milton Miller [Thu, 29 Mar 2007 13:31:41 +0000 (07:31 -0600)]
[POWERPC] bootwrapper: Decompress less, check more
Our kernels put everything in the first load segment, and we read that.
Instead of decompressing to the end of the gzip stream or supplied image
and hoping we get it all, decompress the expected size and complain if
it is not available.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Milton Miller [Wed, 28 Mar 2007 08:21:04 +0000 (02:21 -0600)]
[POWERPC] bootwrapper: no-gzip fixes
Commit a9903811bf8d130a26004f9cb27b66513a267908 missed two uses of the
the .gz suffix in the wrapper script and didn't clean the additonal
possibly cached files.
Signed-off-by: Milton Miller <miltonm@bga.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Milton Miller [Wed, 28 Mar 2007 08:21:02 +0000 (02:21 -0600)]
[POWERPC] bootwrapper: missing relocation in crt0.S
crt0.S had provisions to provide run address relocaton to got2 and
cache flush, but not on the bss clear or stack pointer load. Apply
the same fixup for them.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
72486f1f8f0a2bc828b9d30cf4690cf2dd6807fc inverted the sense for enabling
hotplug CPU controls without reference to any other architecture other than
i386, ia64 and PowerPC. This left everyone else without hotplug CPU control.
Fix powerpc for this brain damage.
(akpm: patch adapted from rmk's ARM fix. Changelog stolen from rmk)
Signed-off-by: Giuliano Pochini <pochini@shiny.it> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Bart Van Assche [Tue, 27 Mar 2007 05:40:29 +0000 (21:40 -0800)]
[POWERPC] Ocotea board: ntpd complains that the frequency error exceeds the tolerance
Lifted from http://bugzilla.kernel.org/show_bug.cgi?id=8182
Steps to reproduce:
- Boot an Ocotea board with the mainline 2.6.20.1 kernel.
- Create an /etc/ntp.conf file with at least one NTP server and iburst mode set.
- Issue the command "ntpd -g".
- Wait about two minutes.
- Verify ntpd's status via "ntpq -pn" and by looking in /var/log/ntp.
This fixes this problem by adjusting the expected clock frequency.
Cc: Kumar Gala <galak@gate.crashing.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no reason to yield the CPU in spu_yield - if the backing
thread reenters spu_run it gets added to the end of the runqueue for
it's priority. So the yield is just a slowdown for the case where
we have higher priority contexts waiting.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
Tony Vroon [Thu, 22 Mar 2007 23:31:08 +0000 (23:31 +0000)]
[POWERPC] PMU LED whitelisting of PowerMac 7,2 and 7,3
This allows the PMU LED on both a PowerMac 7,2 (Dual G5 2.0GHz, June 2003)
and a PowerMac 7,3 (Dual G5 2.0GHz, June 2004) to be controlled.
The physical LED is never off, unlike an iBook/PowerBook LED.
It is rather dim ("off") or very bright ("on").
Signed-off-by: Tony Vroon <chainsaw@gentoo.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olaf Hering [Thu, 22 Mar 2007 22:14:07 +0000 (23:14 +0100)]
[POWERPC] Fix link errors when EEH is disabled
Fix link errors with CONFIG_EEH=n:
arch/powerpc/platforms/built-in.o: In function `.pcibios_fixup_new_pci_devices':
(.text+0x41c8): undefined reference to `.eeh_add_device_tree_late'
arch/powerpc/platforms/built-in.o: In function `.init_phb_dynamic':
(.text+0x4280): undefined reference to `.eeh_add_device_tree_early'
arch/powerpc/platforms/built-in.o: In function `.pcibios_remove_pci_devices':
(.text+0x42fc): undefined reference to `.eeh_remove_bus_device'
arch/powerpc/platforms/built-in.o: In function `.pcibios_add_pci_devices':
(.text+0x43c0): undefined reference to `.eeh_add_device_tree_early'
arch/powerpc/platforms/built-in.o: In function `.pSeries_final_fixup':
(.init.text+0xb4): undefined reference to `.pci_addr_cache_build'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Thu, 22 Mar 2007 06:02:21 +0000 (17:02 +1100)]
[POWERPC] Clean up zImage handling of the command line
This cleans up how the zImage code manipulates the kernel
command line. Notable improvements from the old handling:
- Command line manipulation is consolidated into a new
prep_cmdline() function, rather than being scattered across start()
and some helper functions
- Less stack space use: we use just a single global command
line buffer, which can be initialized by an external tool as before,
we no longer need another command line sized buffer on the stack.
- Easier to support platforms whose firmware passes a
commandline, but not a device tree. Platform code can now point new
loader_info fields to the firmware's command line, rather than having
to do early manipulation of the /chosen bootargs property which may
then be rewritten again by the core.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
David Gibson [Thu, 22 Mar 2007 06:02:21 +0000 (17:02 +1100)]
[POWERPC] Add device tree utility functions to zImage
This patch adds a library of useful device tree manipulation functions
to the zImage library, for use by platform code. These functions are
based on the hooks already in dt_ops, so they're not dependent on a
particular device tree implementation. This patch also slightly
streamlines the code in main.c using these new functions.
This is a consolidation of my work in this area with Scott Wood's
patches to a very similar end.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Olof Johansson [Thu, 22 Mar 2007 14:34:13 +0000 (09:34 -0500)]
[POWERPC] Use mtocrf instruction in asm when CONFIG_POWER4_ONLY=y
mtocrf is a faster single-field mtcrf (move to condition register
fields) instruction available in POWER4 and later processors. It can
make quite a difference in performance on some implementations, so use
it for CONFIG_POWER4_ONLY builds.
Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Jake Moilanen [Thu, 29 Mar 2007 13:44:02 +0000 (08:44 -0500)]
[POWERPC] DMA 4GB boundary protection
There are many adapters which cannot handle DMAing across any 4 GB
boundary. For instance, the latest Emulex adapters.
This normally is not an issue as firmware gives dma-windows under
4gigs. However, some of the new System-P boxes have dma-windows above
4gigs, and this present a problem.
During initialization of the IOMMU tables, the last entry at each 4GB
boundary is marked as used. Thus no mappings can cross the boundary.
If a table ends at a 4GB boundary, the entry is not marked as used.
A boot option to remove this 4GB protection is given w/ protect4gb=off.
This exposes the potential issue for driver and hardware development
purposes.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Sylvain Munaut [Mon, 12 Feb 2007 22:13:27 +0000 (23:13 +0100)]
[POWERPC] Add uevent handler for of_platform_bus
Adding this handler allow userspace to properly handle the module
autoloading. The generation of the uevent itself is now common to
all bus using of_device, so not much code here.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
myri10ge: update driver version to 1.3.0-1.233
myri10ge: more Intel chipsets providing aligned PCIe completions
myri10ge: fix management of the firmware 4KB boundary crossing restriction
cxgb3 - missing CPL hanler and register setting.
cxgb3 - MAC watchdog update
cxgb3 - avoid deadlock with mac watchdog
skge: fix wake on lan
sky2: phy workarounds for Yukon EC-U A1
sky2: turn on clocks when doing resume
sky2: turn carrier off when down
skge: turn carrier off when down
[PATCH] bcm43xx: Fix PPC machine checks and match loopback gain specs
[PATCH] bcm43xx: Fix 802.11b/g scan limits to match regulatory reqs
[PATCH] zd1211rw: Fix E2P_PHY_REG patching
[PATCH] zd1211rw: Reject AL2230S devices
projects / linux-2.6 / log