While trying to look for superfluous I/O accesses that can be optimized
away, I stumbled upon this ACPI sleep I/O access and couldn't figure out
why the hell this dummy op was necessary.
After more than one hour of internet research, I had collected a sufficient
number of documents (among those very old kernel versions) that finally
told me what this dummy read was about: STPCLK# doesn't get asserted in time
on (some) chipsets, which is why we need to have a dummy I/O read to delay
further instruction processing until the CPU is fully stopped.
Signed-off-by: Andreas Mohr <andi@lisas.de> Signed-off-by: Len Brown <len.brown@intel.com>
ACPI: C-States: only demote on current bus mastering activity
Only if bus master activity is going on at the present, we should avoid
entering C3-type sleep, as it might be a faulty transition. As long as the
bm_activity bitmask was based on the number of calls to the ACPI idle
function, looking at previous moments made sense. Now, with it being based on
what happened this jiffy, looking at this jiffy should be sufficient.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Len Brown <len.brown@intel.com>
Do not assume there was bus mastering activity if the idle handler didn't get
called, as there's only reason to not enter C3-type sleep if there is bus
master activity going on. Only for the "promotion" into C3-type sleep bus
mastering activity is taken into account, and there only current bus mastering
activity, and not pure guessing should lead to the decision on whether to
enter C3-type sleep or not.
Also, as bm_activity is a jiffy-based bitmask (bit 0: bus mastering activity
during this juffy, bit 31: bus mastering activity 31 jiffies ago), fix the
setting of bit 0, as it might be called multiple times within one jiffy.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Len Brown <len.brown@intel.com>
Track the actual time spent in C-States (C2 upwards, we can't determine this
for C1), not only the number of invocations. This is especially useful for
dynamic ticks / "tickless systems", but is also of interest on normal systems,
as any interrupt activity leads to C-States being exited, not only the timer
interrupt.
The time is being measured in PM timer ticks, so an increase by one equals 279
nanoseconds.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Len Brown <len.brown@intel.com>
Implemented a new acpi_spinlock type for the OSL lock
interfaces. This allows the type to be customized to
the host OS for improved efficiency (since a spinlock is
usually a very small object.)
Implemented support for "ignored" bits in the ACPI
registers. According to the ACPI specification, these
bits should be preserved when writing the registers via
a read/modify/write cycle. There are 3 bits preserved
in this manner: PM1_CONTROL[0] (SCI_EN), PM1_CONTROL[9],
and PM1_STATUS[11].
http://bugzilla.kernel.org/show_bug.cgi?id=3691
Implemented the initial deployment of new OSL mutex
interfaces. Since some host operating systems have
separate mutex and semaphore objects, this feature was
requested. The base code now uses mutexes (and the new
mutex interfaces) wherever a binary semaphore was used
previously. However, for the current release, the mutex
interfaces are defined as macros to map them to the
existing semaphore interfaces.
Fixed several problems with the support for the control
method SyncLevel parameter. The SyncLevel now works
according to the ACPI specification and in concert with the
Mutex SyncLevel parameter, since the current SyncLevel is
a property of the executing thread. Mutual exclusion for
control methods is now implemented with a mutex instead
of a semaphore.
Fixed three instances of the use of the C shift operator
in the bitfield support code (exfldio.c) to avoid the use
of a shift value larger than the target data width. The
behavior of C compilers is undefined in this case and can
cause unpredictable results, and therefore the case must
be detected and avoided. (Fiodor Suietov)
Added an info message whenever an SSDT or OEM table
is loaded dynamically via the Load() or LoadTable()
ASL operators. This should improve debugging capability
since it will show exactly what tables have been loaded
(beyond the tables present in the RSDT/XSDT.)
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Len Brown <len.brown@intel.com>
Kristen Accardi [Wed, 28 Jun 2006 07:09:54 +0000 (03:09 -0400)]
ACPIPHP: prevent duplicate slot numbers when no _SUN
Dock bridges generally do not implement _SUN, yet show up as ejectable
slots. If you have more than one ejectable slot that does not implement
SUN, with the current code you will get duplicate slot numbers. So, if
there is no _SUN, use the current count of the number of slots found
instead.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Len Brown <len.brown@intel.com>
Kristen Accardi [Wed, 28 Jun 2006 07:08:06 +0000 (03:08 -0400)]
ACPIPHP: use ACPI dock driver
Modify the acpiphp driver to use the ACPI dock driver for dock
notifications. Only load the acpiphp driver if we find we have pci dock
devices.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Len Brown <len.brown@intel.com>
Kristen Accardi [Wed, 28 Jun 2006 07:07:16 +0000 (03:07 -0400)]
ACPI: dock driver
Create a driver which lives in the acpi subsystem to handle dock events.
This driver is not an "ACPI" driver, because acpi drivers require that the
object be present when the driver is loaded.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Cc: Dave Hansen <haveblue@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Len Brown <len.brown@intel.com>
Kristen Accardi [Sat, 24 Jun 2006 23:36:00 +0000 (19:36 -0400)]
KEVENT: add new uevent for dock
so that userspace can be notified of dock and undock events.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Len Brown <len.brown@intel.com>
The ASL Acquire operator (17.5.1 in ACPI 3.0 spec) is allowed to time out
and return True without acquiring the semaphore. There's no indication in
the spec that this is an actual error, so this message should be
debug-only, as the message for successful acquisition is.
This used to be an ACPI_DEBUG_PRINT, but it was mis-classified as
ACPI_DB_ERROR rather than ACPI_DB_MUTEX, so it got swept up in Thomas'
recent patch to enable ACPI error messages even without CONFIG_ACPI_DEBUG.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Mon, 26 Jun 2006 23:06:08 +0000 (16:06 -0700)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (56 commits)
[PATCH] fs/ocfs2/dlm/: cleanups
ocfs2: fix compiler warnings in dlm_convert_lock_handler()
ocfs2: dlm_print_one_mle() needs to be defined
ocfs2: remove whitespace in dlmunlock.c
ocfs2: move dlm work to a private work queue
ocfs2: fix incorrect error returns
ocfs2: tune down some noisy messages during dlm recovery
ocfs2: display message before waiting for recovery to complete
ocfs2: mlog in dlm_convert_lock_handler() should be ML_ERROR
ocfs2: retry operations when a lock is marked in recovery
ocfs2: use cond_resched() in dlm_thread()
ocfs2: use GFP_NOFS in some dlm operations
ocfs2: wait for recovery when starting lock mastery
ocfs2: continue recovery when a dead node is encountered
ocfs2: remove unneccesary spin_unlock() in dlm_remaster_locks()
ocfs2: dlm_remaster_locks() should never exit without completing
ocfs2: special case recovery lock in dlmlock_remote()
ocfs2: pending mastery asserts and migrations should block each other
ocfs2: temporarily disable automatic lock migration
ocfs2: do not unconditionally purge the lockres in dlmlock_remote()
...
Kurt Hackel [Mon, 1 May 2006 21:29:28 +0000 (14:29 -0700)]
ocfs2: retry operations when a lock is marked in recovery
Before checking for a nonexistent lock, make sure the lockres is not marked
RECOVERING. The caller will just retry and the state should be fixed up when
recovery completes.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Kurt Hackel [Mon, 1 May 2006 20:49:20 +0000 (13:49 -0700)]
ocfs2: dlm_remaster_locks() should never exit without completing
We cannot restart recovery. Once we begin to recover a node, keep the state
of the recovery intact and follow through, regardless of any other node
deaths that may occur.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Kurt Hackel [Mon, 1 May 2006 20:47:50 +0000 (13:47 -0700)]
ocfs2: special case recovery lock in dlmlock_remote()
If the previous master of the recovery lock dies, let calc_usage take it
down completely and let the caller completely redo the dlmlock() call.
Otherwise, there will never be an opportunity to re-master the lockres and
recovery wont be able to progress.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Kurt Hackel [Mon, 1 May 2006 20:32:27 +0000 (13:32 -0700)]
ocfs2: pending mastery asserts and migrations should block each other
Use the existing structure for blocking migrations when ASTs are pending to
achieve the same result. If we can catch the assert before it goes on the
wire, just cancel it and let the migration continue.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Now we never change the owner of a lock resource until unmount or node
death. This will be re-enabled once some issues in the algorithm used have
been resolved.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Kurt Hackel [Mon, 1 May 2006 20:27:10 +0000 (13:27 -0700)]
ocfs2: do not unconditionally purge the lockres in dlmlock_remote()
In dlmlock_remote(), do not call purge_lockres until the lock resource
actually changes. otherwise, the mastery info on the lockres will go away
underneath the caller.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Kurt Hackel [Mon, 1 May 2006 19:02:07 +0000 (12:02 -0700)]
ocfs2: increase backoff before waiting for recovery
When mastering non-recovery lock resources, additional time was frequently
needed to allow the disk heartbeat to catch up with the network timeout. the
recovery lock resource is time critical and avoids this path.
Signed-off-by: Kurt Hackel <kurt.hackel@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Joel Becker [Fri, 17 Mar 2006 01:40:37 +0000 (17:40 -0800)]
[PATCH] ocfs2: Alloc at least a page for the DLM hash
The OCFS2 DLM allocates a number of pages for a hash to lookup locks.
There was a bug where a PAGE_SIZE bigger than the hash size (eg, 64K
pages) would result in zero pages allocated.
Signed-off-by: Joel Becker <joel.becker@oracle.com> Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial:
typo fixes
Clean up 'inline is not at beginning' warnings for usb storage
Storage class should be first
i386: Trivial typo fixes
ixj: make ixj_set_tone_off() static
spelling fixes
fix paniced->panicked typos
Spelling fixes for Documentation/atomic_ops.txt
move acknowledgment for Mark Adler to CREDITS
remove the bouncing email address of David Campbell
Karsten Keil [Mon, 26 Jun 2006 18:21:01 +0000 (20:21 +0200)]
[PATCH] fix processing of the last byte in isdn_readbchan_tty()
The changes in the tty handling contain a bug while accessing
the last byte in the skb. Since special sequence for control of
DTMF and FAX via ttyI* devices handled via this path, these services
do not work anymore.
"It seems too little tested: "losetup -d /dev/loop0" fails with
EINVAL because nothing sets lo_thread; but even when you patch
loop_thread() to set lo->lo_thread = current, it can't survive
more than a few dozen iterations of the loop below (with a tmpfs
mounted on /tst):
j=0
cp /dev/zero /tst
while :
do
let j=j+1
echo "Doing pass $j"
losetup /dev/loop0 /tst/zero
mkfs -t ext2 -b 1024 /dev/loop0 >/dev/null 2>&1
mount -t ext2 /dev/loop0 /mnt
umount /mnt
losetup -d /dev/loop0
done
it collapses with failed ioctl then BUG_ON(!bio).
I think the original lo_done completion was more subtle and safe
than the kthread conversion has allowed for."
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: trivial fixes in Makefile
kbuild: adding symbols in Kconfig and defconfig to TAGS
kbuild: replace abort() with exit(1)
kbuild: support for %.symtypes files
kbuild: fix silentoldconfig recursion
kbuild: add option for stripping modules while installing them
kbuild: kill some false positives from modpost
kbuild: export-symbol usage report generator
kbuild: fix make -rR breakage
kbuild: append -dirty for updated but uncommited changes
kbuild: append git revision for all untagged commits
kbuild: fix module.symvers parsing in modpost
kbuild: ignore make's built-in rules & variables
kbuild: bugfix with initramfs
kbuild: modpost build fix
kbuild: check license compatibility when building modules
kbuild: export-type enhancement to modpost.c
kbuild: add dependency on kernel.release to the package targets
kbuild: `make kernelrelease' speedup
kconfig: KCONFIG_OVERWRITECONFIG
...
Greg Ungerer [Mon, 26 Jun 2006 06:33:15 +0000 (16:33 +1000)]
[PATCH] m68knommu: use configurable RAM setup page_offset.h
Remove board specific base RAM conditionals from page_offset.h
With the Kconfig time configurable RAM setup none of this is required.
It is all based on the Kconfig (CONFIG_RAMBASE) option now.
Greg Ungerer [Mon, 26 Jun 2006 06:33:05 +0000 (16:33 +1000)]
[PATCH] m68knommu: use configurable RAM setup in linker script
Remove the fixed RAM configurations for each board type from the
linker script. Replace with simple defines usng the flexible RAM
configuration options. This cleans out of lot of board specific
munging of addresses.
Greg Ungerer [Mon, 26 Jun 2006 06:32:59 +0000 (16:32 +1000)]
[PATCH] m68knommu: create configurable RAM setup
Reworked the way RAM regions are defined. Instead of coding all the
variations for each board type we now just configure RAM base and size
in the usual Kconfig setup. This much simplifies the code, and makes it
a lot more flexible when setting up new boards or board varients.
Greg Ungerer [Mon, 26 Jun 2006 06:34:09 +0000 (16:34 +1000)]
[PATCH] m68knommu: remove unused vars from generic 68328 start code
Clean out unused variable definitions from 68328 start up code.
Also use a more appropriate start address for the case of relocating
the kernel code to RAM (from ROM/flash).
projects / linux-2.6 / log