* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Merge avlab serial board entries in parport_serial
[SERIAL] kernel console should send CRLF not LFCR
Alan Cox [Wed, 22 Mar 2006 15:52:40 +0000 (15:52 +0000)]
[PATCH] libata: Fix a drive detection problem
The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andrew Victor [Wed, 22 Mar 2006 20:14:14 +0000 (20:14 +0000)]
[ARM] 3386/1: AT91RM9200 Clock update
Patch from Andrew Victor
This patch includes a few changes to the clock support on the
AT91RM9200.
1. Added definitions for Ethernet, MMC, TWI, USARTs, and SPI peripheral
clocks.
2. Replaced some hard-coded hex values with the text definitions in
at91rm9200_sys.h.
3. If the USB96M bit is set for PLLB, then the rate of PLLB is not
affected but only the USB Host/Device clocks which are derived from it.
Issue reported by Sergei Sharonov.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor [Wed, 22 Mar 2006 20:14:13 +0000 (20:14 +0000)]
[ARM] 3384/1: AT91RM9200: Timer
Patch from Andrew Victor
If the timer interrupt is ever significantly delayed (or after the
system was suspended), the system could spin incrementing the time for
too long.
The fix is to replace the "do {} while" with a "while {}".
Orignal patch by Savin Zlobec and Peter Menzebach.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 3381/1: ixp2000: fix slowport write timing control register fields
Patch from Lennert Buytenhek
The original version of the chip docs had the PW and SU fields in
the slowport write timing control register accidentally reversed.
This is mentioned in the errata (documentation change #4) and fixed
in newer docs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the IXDP2x00s, the NPU that is PCI master is always the egress
(i.e. 'master') NPU. At least on the IXDP2800, both NPUs have flash,
so the ixp2000_has_flash() check in ixdp2x00_master_npu() is useless.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ARM] 3379/1: ixp2000: use generic 8250 debug macros
Patch from Lennert Buytenhek
The xscale UART in the ixp2000 is basically just an 8250 UART (with
some extra bits and pieces), so we can use the generic 8250 debug
macros on the ixp2000.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ixp2000 used to initially mark GPIO interrupts as invalid, and not
mark them valid until set_irq_type() was called, but this doesn't
work if you want to use request_irq() with the SA_TRIGGER_* flags.
So, just mark the GPIO interrupts valid from the beginning. We
configure GPIOs as inputs when set_irq_type() is called anyway, so
this shouldn't be a problem.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Add a secondary TSB for hugepage mappings.
[SPARC]: Respect vm_page_prot in io_remap_page_range().
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Bump driver version and reldate.
[TG3]: Skip phy power down on some devices
[TG3]: Fix SRAM access during tg3_init_one()
[X25]: dte facilities 32 64 ioctl conversion
[X25]: allow ITU-T DTE facilities for x25
[X25]: fix kernel error message 64 bit kernel
[X25]: ioctl conversion 32 bit user to 64 bit kernel
[NET]: socket timestamp 32 bit handler for 64 bit kernel
[NET]: allow 32 bit socket ioctl in 64 bit kernel
[BLUETOOTH]: Return negative error constant
James Morris [Wed, 22 Mar 2006 08:09:22 +0000 (00:09 -0800)]
[PATCH] SELinux: add slab cache for inode security struct
Add a slab cache for the SELinux inode security struct, one of which is
allocated for every inode instantiated by the system.
The memory savings are considerable.
On 64-bit, instead of the size-128 cache, we have a slab object of 96
bytes, saving 32 bytes per object. After booting, I see about 4000 of
these and then about 17,000 after a kernel compile. With this patch, we
save around 530KB of kernel memory in the latter case. On 32-bit, the
savings are about half of this.
Signed-off-by: James Morris <jmorris@namei.org> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
James Morris [Wed, 22 Mar 2006 08:09:20 +0000 (00:09 -0800)]
[PATCH] SELinux: fix hard link count for selinuxfs root directory
A further fix is needed for selinuxfs link count management, to ensure that
the count is correct for the parent directory when a subdirectory is
created. This is only required for the root directory currently, but the
code has been updated for the general case.
Signed-off-by: James Morris <jmorris@namei.org> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
James Morris [Wed, 22 Mar 2006 08:09:19 +0000 (00:09 -0800)]
[PATCH] selinuxfs cleanups: sel_make_avc_files
Fix copy & paste error in sel_make_avc_files(), removing a supurious call to
d_genocide() in the error path. All of this will be cleaned up by
kill_litter_super().
Signed-off-by: James Morris <jmorris@namei.org> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
James Morris [Wed, 22 Mar 2006 08:09:18 +0000 (00:09 -0800)]
[PATCH] selinuxfs cleanups: sel_make_bools
Remove the call to sel_make_bools() from sel_fill_super(), as policy needs to
be loaded before the boolean files can be created. Policy will never be
loaded during sel_fill_super() as selinuxfs is kernel mounted during init and
the only means to load policy is via selinuxfs.
Also, the call to d_genocide() on the error path of sel_make_bools() is
incorrect and replaced with sel_remove_bools().
Signed-off-by: James Morris <jmorris@namei.org> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unify the error path of sel_fill_super() so that all errors pass through the
same point and generate an error message. Also, removes a spurious dput() in
the error path which breaks the refcounting for the filesystem
(litter_kill_super() will correctly clean things up itself on error).
Signed-off-by: James Morris <jmorris@namei.org> Acked-by: Stephen Smalley <sds@tycho.nsa.gov> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stephen Smalley [Wed, 22 Mar 2006 08:09:13 +0000 (00:09 -0800)]
[PATCH] selinux: Disable automatic labeling of new inodes when no policy is loaded
This patch disables the automatic labeling of new inodes on disk
when no policy is loaded.
Discussion is here:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=180296
In short, we're changing the behavior so that when no policy is loaded,
SELinux does not label files at all. Currently it does add an 'unlabeled'
label in this case, which we've found causes problems later.
SELinux always maintains a safe internal label if there is none, so with this
patch, we just stick with that and wait until a policy is loaded before adding
a persistent label on disk.
The effect is simply that if you boot with SELinux enabled but no policy
loaded and create a file in that state, SELinux won't try to set a security
extended attribute on the new inode on the disk. This is the only sane
behavior for SELinux in that state, as it cannot determine the right label to
assign in the absence of a policy. That state usually doesn't occur, but the
rawhide installer seemed to be misbehaving temporarily so it happened to show
up on a test install.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov> Acked-by: James Morris <jmorris@namei.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Jackson [Wed, 22 Mar 2006 08:09:11 +0000 (00:09 -0800)]
[PATCH] mm: slab cache interleave rotor fix
The alien cache rotor in mm/slab.c assumes that the first online node is
node 0. Eventually for some archs, especially with hotplug, this will no
longer be true.
Fix the interleave rotor to handle the general case of node numbering.
Signed-off-by: Paul Jackson <pj@sgi.com> Acked-by: Christoph Lameter <clameter@engr.sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bogus node loop in hugetlb.c alloc_fresh_huge_page(), which was
assuming that nodes are numbered contiguously from 0 to num_online_nodes().
Once the hotplug folks get this far, that will be false.
Signed-off-by: Paul Jackson <pj@sgi.com> Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] slab: fix drain_array() so that it works correctly with the shared_array
The list_lock also protects the shared array and we call drain_array() with
the shared array. Therefore we cannot go as far as I wanted to but have to
take the lock in a way so that it also protects the array_cache in
drain_pages.
(Note: maybe we should make the array_cache locking more consistent? I.e.
always take the array cache lock for shared arrays and disable interrupts
for the per cpu arrays?)
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] slab: make drain_array more universal by adding more parameters
And a parameter to drain_array to control the freeing of all objects and
then use drain_array() to replace instances of drain_array_locked with
drain_array. Doing so will avoid taking locks in those locations if the
arrays are empty.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] slab: cache_reap(): further reduction in interrupt holdoff
cache_reap takes the l3->list_lock (disabling interrupts) unconditionally
and then does a few checks and maybe does some cleanup. This patch makes
cache_reap() only take the lock if there is work to do and then the lock is
taken and released for each cleaning action.
The checking of when to do the next reaping is done without any locking and
becomes racy. Should not matter since reaping can also be skipped if the
slab mutex cannot be acquired.
The same is true for the touched processing. If we get this wrong once in
awhile then we will mistakenly clean or not clean the shared cache. This
will impact performance slightly.
Note that the additional drain_array() function introduced here will fall
out in a subsequent patch since array cleaning will now be very similar
from all callers.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make shrink_all_memory() repeat the attempts to free more memory if there
seems to be no pages to free.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Cc: Pavel Machek <pavel@ucw.cz> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chen, Kenneth W [Wed, 22 Mar 2006 08:09:03 +0000 (00:09 -0800)]
[PATCH] optimize follow_hugetlb_page
follow_hugetlb_page() walks a range of user virtual address and then fills
in list of struct page * into an array that is passed from the argument
list. It also gets a reference count via get_page(). For compound page,
get_page() actually traverse back to head page via page_private() macro and
then adds a reference count to the head page. Since we are doing a virt to
pte look up, kernel already has a struct page pointer into the head page.
So instead of traverse into the small unit page struct and then follow a
link back to the head page, optimize that with incrementing the reference
count directly on the head page.
The benefit is that we don't take a cache miss on accessing page struct for
the corresponding user address and more importantly, not to pollute the
cache with a "not very useful" round trip of pointer chasing. This adds a
moderate performance gain on an I/O intensive database transaction
workload.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com> Cc: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Quite a long time back, prepare_hugepage_range() replaced
is_aligned_hugepage_range() as the callback from mm/mmap.c to arch code to
verify if an address range is suitable for a hugepage mapping.
is_aligned_hugepage_range() stuck around, but only to implement
prepare_hugepage_range() on archs which didn't implement their own.
Most archs (everything except ia64 and powerpc) used the same
implementation of is_aligned_hugepage_range(). On powerpc, which
implements its own prepare_hugepage_range(), the custom version was never
used.
In addition, "is_aligned_hugepage_range()" was a bad name, because it
suggests it returns true iff the given range is a good hugepage range,
whereas in fact it returns 0-or-error (so the sense is reversed).
This patch cleans up by abolishing is_aligned_hugepage_range(). Instead
prepare_hugepage_range() is defined directly. Most archs use the default
version, which simply checks the given region is aligned to the size of a
hugepage. ia64 and powerpc define custom versions. The ia64 one simply
checks that the range is in the correct address space region in addition to
being suitably aligned. The powerpc version (just as previously) checks
for suitable addresses, and if necessary performs low-level MMU frobbing to
set up new areas for use by hugepages.
No libhugetlbfs testsuite regressions on ppc64 (POWER5 LPAR).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:59 +0000 (00:08 -0800)]
[PATCH] hugepage: Move hugetlb_free_pgd_range() prototype to hugetlb.h
The optional hugepage callback, hugetlb_free_pgd_range() is presently
implemented non-trivially only on ia64 (but I plan to add one for powerpc
shortly). It has its own prototype for the function in asm-ia64/pgtable.h.
However, since the function is called from generic code, it make sense for
its prototype to be in the generic hugetlb.h header file, as the protypes
other arch callbacks already are (prepare_hugepage_range(),
set_huge_pte_at(), etc.). This patch makes it so.
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:58 +0000 (00:08 -0800)]
[PATCH] hugepage: Fix hugepage logic in free_pgtables() harder
Turns out the hugepage logic in free_pgtables() was doubly broken. The
loop coalescing multiple normal page VMAs into one call to free_pgd_range()
had an off by one error, which could mean it would coalesce one hugepage
VMA into the same bundle (checking 'vma' not 'next' in the loop). I
transferred this bug into the new is_vm_hugetlb_page() based version.
Here's the fix.
This one didn't bite on powerpc previously for the same reason the
is_hugepage_only_range() problem didn't: powerpc's hugetlb_free_pgd_range()
is identical to free_pgd_range(). It didn't bite on ia64 because the
hugepage region is distant enough from any other region that the separated
PMD_SIZE distance test would always prevent coalescing the two together.
No libhugetlbfs testsuite regressions (ppc64, POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:57 +0000 (00:08 -0800)]
[PATCH] hugepage: Fix hugepage logic in free_pgtables()
free_pgtables() has special logic to call hugetlb_free_pgd_range() instead
of the normal free_pgd_range() on hugepage VMAs. However, the test it uses
to do so is incorrect: it calls is_hugepage_only_range on a hugepage sized
range at the start of the vma. is_hugepage_only_range() will return true
if the given range has any intersection with a hugepage address region, and
in this case the given region need not be hugepage aligned. So, for
example, this test can return true if called on, say, a 4k VMA immediately
preceding a (nicely aligned) hugepage VMA.
At present we get away with this because the powerpc version of
hugetlb_free_pgd_range() is just a call to free_pgd_range(). On ia64 (the
only other arch with a non-trivial is_hugepage_only_range()) we get away
with it for a different reason; the hugepage area is not contiguous with
the rest of the user address space, and VMAs are not permitted in between,
so the test can't return a false positive there.
Nonetheless this should be fixed. We do that in the patch below by
replacing the is_hugepage_only_range() test with an explicit test of the
VMA using is_vm_hugetlb_page().
This in turn changes behaviour for platforms where is_hugepage_only_range()
returns false always (everything except powerpc and ia64). We address this
by ensuring that hugetlb_free_pgd_range() is defined to be identical to
free_pgd_range() (instead of a no-op) on everything except ia64. Even so,
it will prevent some otherwise possible coalescing of calls down to
free_pgd_range(). Since this only happens for hugepage VMAs, removing this
small optimization seems unlikely to cause any trouble.
This patch causes no regressions on the libhugetlbfs testsuite - ppc64
POWER5 (8-way), ppc64 G5 (2-way) and i386 Pentium M (UP).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Acked-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:56 +0000 (00:08 -0800)]
[PATCH] hugepage: Make {alloc,free}_huge_page() local
Originally, mm/hugetlb.c just handled the hugepage physical allocation path
and its {alloc,free}_huge_page() functions were used from the arch specific
hugepage code. These days those functions are only used with mm/hugetlb.c
itself. Therefore, this patch makes them static and removes their
prototypes from hugetlb.h. This requires a small rearrangement of code in
mm/hugetlb.c to avoid a forward declaration.
This patch causes no regressions on the libhugetlbfs testsuite (ppc64,
POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:55 +0000 (00:08 -0800)]
[PATCH] hugepage: Strict page reservation for hugepage inodes
These days, hugepages are demand-allocated at first fault time. There's a
somewhat dubious (and racy) heuristic when making a new mmap() to check if
there are enough available hugepages to fully satisfy that mapping.
A particularly obvious case where the heuristic breaks down is where a
process maps its hugepages not as a single chunk, but as a bunch of
individually mmap()ed (or shmat()ed) blocks without touching and
instantiating the pages in between allocations. In this case the size of
each block is compared against the total number of available hugepages.
It's thus easy for the process to become overcommitted, because each block
mapping will succeed, although the total number of hugepages required by
all blocks exceeds the number available. In particular, this defeats such
a program which will detect a mapping failure and adjust its hugepage usage
downward accordingly.
The patch below addresses this problem, by strictly reserving a number of
physical hugepages for hugepage inodes which have been mapped, but not
instatiated. MAP_SHARED mappings are thus "safe" - they will fail on
mmap(), not later with an OOM SIGKILL. MAP_PRIVATE mappings can still
trigger an OOM. (Actually SHARED mappings can technically still OOM, but
only if the sysadmin explicitly reduces the hugepage pool between mapping
and instantiation)
This patch appears to address the problem at hand - it allows DB2 to start
correctly, for instance, which previously suffered the failure described
above.
This patch causes no regressions on the libhugetblfs testsuite, and makes a
test (designed to catch this problem) pass which previously failed (ppc64,
POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:53 +0000 (00:08 -0800)]
[PATCH] hugepage: serialize hugepage allocation and instantiation
Currently, no lock or mutex is held between allocating a hugepage and
inserting it into the pagetables / page cache. When we do go to insert the
page into pagetables or page cache, we recheck and may free the newly
allocated hugepage. However, since the number of hugepages in the system
is strictly limited, and it's usualy to want to use all of them, this can
still lead to spurious allocation failures.
For example, suppose two processes are both mapping (MAP_SHARED) the same
hugepage file, large enough to consume the entire available hugepage pool.
If they race instantiating the last page in the mapping, they will both
attempt to allocate the last available hugepage. One will fail, of course,
returning OOM from the fault and thus causing the process to be killed,
despite the fact that the entire mapping can, in fact, be instantiated.
The patch fixes this race by the simple method of adding a (sleeping) mutex
to serialize the hugepage fault path between allocation and insertion into
pagetables and/or page cache. It would be possible to avoid the
serialization by catching the allocation failures, waiting on some
condition, then rechecking to see if someone else has instantiated the page
for us. Given the likely frequency of hugepage instantiations, it seems
very doubtful it's worth the extra complexity.
This patch causes no regression on the libhugetlbfs testsuite, and one
test, which can trigger this race now passes where it previously failed.
Actually, the test still sometimes fails, though less often and only as a
shmat() failure, rather processes getting OOM killed by the VM. The dodgy
heuristic tests in fs/hugetlbfs/inode.c for whether there's enough hugepage
space aren't protected by the new mutex, and would be ugly to do so, so
there's still a race there. Another patch to replace those tests with
something saner for this reason as well as others coming...
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Gibson [Wed, 22 Mar 2006 08:08:51 +0000 (00:08 -0800)]
[PATCH] hugepage: Small fixes to hugepage clear/copy path
Move the loops used in mm/hugetlb.c to clear and copy hugepages to their
own functions for clarity. As we do so, we add some checks of need_resched
- we are, after all copying megabytes of memory here. We also add
might_sleep() accordingly. We generally dropped locks around the clear and
copy, already but not everyone has PREEMPT enabled, so we should still be
checking explicitly.
For this to work, we need to remove the clear_huge_page() from
alloc_huge_page(), which is called with the page_table_lock held in the COW
path. We move the clear_huge_page() to just after the alloc_huge_page() in
the hugepage no-page path. In the COW path, the new page is about to be
copied over, so clearing it was just a waste of time anyway. So as a side
effect we also fix the fact that we held the page_table_lock for far too
long in this path by calling alloc_huge_page() under it.
It causes no regressions on the libhugetlbfs testsuite (ppc64, POWER5).
Signed-off-by: David Gibson <dwg@au1.ibm.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Zhang, Yanmin [Wed, 22 Mar 2006 08:08:50 +0000 (00:08 -0800)]
[PATCH] Enable mprotect on huge pages
2.6.16-rc3 uses hugetlb on-demand paging, but it doesn_t support hugetlb
mprotect.
From: David Gibson <david@gibson.dropbear.id.au>
Remove a test from the mprotect() path which checks that the mprotect()ed
range on a hugepage VMA is hugepage aligned (yes, really, the sense of
is_aligned_hugepage_range() is the opposite of what you'd guess :-/).
In fact, we don't need this test. If the given addresses match the
beginning/end of a hugepage VMA they must already be suitably aligned. If
they don't, then mprotect_fixup() will attempt to split the VMA. The very
first test in split_vma() will check for a badly aligned address on a
hugepage VMA and return -EINVAL if necessary.
On i386 and x86-64, pte flag _PAGE_PSE collides with _PAGE_PROTNONE. The
identify of hugetlb pte is lost when changing page protection via mprotect.
A page fault occurs later will trigger a bug check in huge_pte_alloc().
The fix is to always make new pte a hugetlb pte and also to clean up
legacy code where _PAGE_PRESENT is forced on in the pre-faulting day.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com> Cc: David Gibson <david@gibson.dropbear.id.au> Cc: "David S. Miller" <davem@davemloft.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Ken Chen <kenneth.w.chen@intel.com> Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com> Cc: Andi Kleen <ak@muc.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current current get_init_ra_size is not optimal across different IO
sizes and max_readahead values. Here is a quick summary of sizes computed
under current design and under the attached patch. All of these assume 1st
IO at offset 0, or 1st detected sequential IO.
32k max, 4k request
old new
-----------------
8k 8k
16k 16k
32k 32k
128k max, 4k request
old new
-----------------
32k 16k
64k 32k
128k 64k
128k 128k
128k max, 32k request
old new
-----------------
32k 64k <-----
64k 128k
128k 128k
512k max, 4k request
old new
-----------------
4k 32k <----
16k 64k
64k 128k
128k 256k
512k 512k
Cc: Oleg Nesterov <oleg@tv-sign.ru> Cc: Steven Pratt <slpratt@austin.ibm.com> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Oleg Nesterov [Wed, 22 Mar 2006 08:08:47 +0000 (00:08 -0800)]
[PATCH] readahead: ->prev_page can overrun the ahead window
If get_next_ra_size() does not grow fast enough, ->prev_page can overrun
the ahead window. This means the caller will read the pages from
->ahead_start + ->ahead_size to ->prev_page synchronously.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru> Cc: Steven Pratt <slpratt@austin.ibm.com> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh Dickins [Wed, 22 Mar 2006 08:08:46 +0000 (00:08 -0800)]
[PATCH] shmem: inline to avoid warning
shmem.c was named and shamed in Jesper's "Building 100 kernels" warnings:
shmem_parse_mpol is only used when CONFIG_TMPFS parses mount options; and
only called from that one site, so mark it inline like its non-NUMA stub.
[PATCH] vmscan: emove obsolete checks from shrink_list() and fix unlikely in refill_inactive_zone()
As suggested by Marcelo:
1. The optimization introduced recently for not calling
page_referenced() during zone reclaim makes two additional checks in
shrink_list unnecessary.
2. The if (unlikely(sc->may_swap)) in refill_inactive_zone is optimized
for the zone_reclaim case. However, most peoples system only does swap.
Undo that.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Marcelo Tosatti <marcelo.tosatti@cyclades.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 22 Mar 2006 08:08:40 +0000 (00:08 -0800)]
[PATCH] remove set_page_count() outside mm/
set_page_count usage outside mm/ is limited to setting the refcount to 1.
Remove set_page_count from outside mm/, and replace those users with
init_page_count() and set_page_refcounted().
This allows more debug checking, and tighter control on how code is allowed
to play around with page->_count.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A couple of places set_page_count(page, 1) that don't need to.
Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 22 Mar 2006 08:08:33 +0000 (00:08 -0800)]
[PATCH] mm: make __put_page internal
Remove __put_page from outside the core mm/. It is dangerous because it does
not handle compound pages nicely, and misses 1->0 transitions. If a user
later appears that really needs the extra speed we can reevaluate.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 22 Mar 2006 08:08:32 +0000 (00:08 -0800)]
[PATCH] x86_64: pageattr use single list
Use page->lru.next to implement the singly linked list of pages rather than
the struct deferred_page which needs to be allocated and freed for each
page.
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 22 Mar 2006 08:08:30 +0000 (00:08 -0800)]
[PATCH] sg: use compound pages
sg increments the refcount of constituent pages in its higher order memory
allocations when they are about to be mapped by userspace. This is done so
the subsequent get_page/put_page when doing the mapping and unmapping does not
free the page.
Move over to the preferred way, that is, using compound pages instead. This
fixes a whole class of possible obscure bugs where a get_user_pages on a
constituent page may outlast the user mappings or even the driver.
Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Hugh Dickins <hugh@veritas.com> Cc: Douglas Gilbert <dougg@torque.net> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh Dickins [Wed, 22 Mar 2006 08:08:29 +0000 (00:08 -0800)]
[PATCH] remove VM_DONTCOPY bogosities
Now that it's madvisable, remove two pieces of VM_DONTCOPY bogosity:
1. There was and is no logical reason why VM_DONTCOPY should be in the
list of flags which forbid vma merging (and those drivers which set
it are also setting VM_IO, which itself forbids the merge).
2. It's hard to understand the purpose of the VM_HUGETLB, VM_DONTCOPY
block in vm_stat_account: but never mind, it's under CONFIG_HUGETLB,
which (unlike CONFIG_HUGETLB_PAGE or CONFIG_HUGETLBFS) has never been
defined.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] zone_reclaim: additional comments and cleanup
Add some comments to explain how zone reclaim works. And it fixes the
following issues:
- PF_SWAPWRITE needs to be set for RECLAIM_SWAP to be able to write
out pages to swap. Currently RECLAIM_SWAP may not do that.
- remove setting nr_reclaimed pages after slab reclaim since the slab shrinking
code does not use that and the nr_reclaimed pages is just right for the
intended follow up action.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Wed, 22 Mar 2006 08:08:20 +0000 (00:08 -0800)]
[PATCH] vmscan return nr_reclaimed
Change all the vmscan functions to retunr the number-of-reclaimed pages and
remove scan_conrtol.nr_reclaimed.
Saves ten-odd bytes of text and makes things clearer and more consistent.
The patch also changes the behaviour of zone_reclaim() when it falls back to slab shrinking. Christoph says
"Setting this to one means that we will rescan and shrink the slab for
each allocation if we are out of zone memory and RECLAIM_SLAB is set. Plus
if we do an order 0 allocation we do not go off node as intended.
"We better set this to zero. This means the allocation will go offnode
despite us having potentially freed lots of memory on the zone. Future
allocations can then again be done from this zone."
Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Christoph Lameter <christoph@lameter.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Wed, 22 Mar 2006 08:08:19 +0000 (00:08 -0800)]
[PATCH] vmscan: use unsigned longs
Turn basically everything in vmscan.c into `unsigned long'. This is to avoid
the possibility that some piece of code in there might decide to operate upon
more than 4G (or even 2G) of pages in one hit.
This might be silly, but we'll need it one day.
Cc: Christoph Lameter <clameter@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Wed, 22 Mar 2006 08:08:18 +0000 (00:08 -0800)]
[PATCH] vmscan: scan_control cleanup
Initialise as much of scan_control as possible at the declaration site. This
tidies things up a bit and assures us that all unmentioned fields are zeroed
out.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] Thin out scan_control: remove nr_to_scan and priority
Make nr_to_scan and priority a parameter instead of putting it into scan
control. This allows various small optimizations and IMHO makes the code
easier to read.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Wed, 22 Mar 2006 08:08:16 +0000 (00:08 -0800)]
[PATCH] on_each_cpu(): disable local interrupts
When on_each_cpu() runs the callback on other CPUs, it runs with local
interrupts disabled. So we should run the function with local interrupts
disabled on this CPU, too.
And do the same for UP, so the callback is run in the same environment on both
UP and SMP. (strictly it should do preempt_disable() too, but I think
local_irq_disable is sufficiently equivalent).
Also uninlines on_each_cpu(). softirq.c was the most appropriate file I could
find, but it doesn't seem to justify creating a new file.
Oh, and fix up that comment over (under?) x86's smp_call_function(). It
drives me nuts.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_NO_REAP is documented as an option that will cause this slab not to be
reaped under memory pressure. However, that is not what happens. The only
thing that SLAB_NO_REAP controls at the moment is the reclaim of the unused
slab elements that were allocated in batch in cache_reap(). Cache_reap()
is run every few seconds independently of memory pressure.
Could we remove the whole thing? Its only used by three slabs anyways and
I cannot find a reason for having this option.
There is an additional problem with SLAB_NO_REAP. If set then the recovery
of objects from alien caches is switched off. Objects not freed on the
same node where they were initially allocated will only be reused if a
certain amount of objects accumulates from one alien node (not very likely)
or if the cache is explicitly shrunk. (Strangely __cache_shrink does not
check for SLAB_NO_REAP)
Getting rid of SLAB_NO_REAP fixes the problems with alien cache freeing.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: Mark Fasheh <mark.fasheh@oracle.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove cachep->spinlock. Locking has moved to the kmem_list3 and most of
the structures protected earlier by cachep->spinlock is now protected by
the l3->list_lock. slab cache tunables like batchcount are accessed always
with the cache_chain_mutex held.
Patch tested on SMP and NUMA kernels with dbench processes running,
constant onlining/offlining, and constant cache tuning, all at the same
time.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org> Cc: Christoph Lameter <christoph@lameter.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 22 Mar 2006 08:08:08 +0000 (00:08 -0800)]
[PATCH] hugepage allocator cleanup
Insert "fresh" huge pages into the hugepage allocator by the same means as
they are freed back into it. This reduces code size and allows
enqueue_huge_page to be inlined into the hugepage free fastpath.
Eliminate occurances of hugepages on the free list with non-zero refcount.
This can allow stricter refcount checks in future. Also required for
lockless pagecache.
Signed-off-by: Nick Piggin <npiggin@suse.de>
"This patch also eliminates a leak "cleaned up" by re-clobbering the
refcount on every allocation from the hugepage freelists. With respect to
the lockless pagecache, the crucial aspect is to eliminate unconditional
set_page_count() to 0 on pages with potentially nonzero refcounts, though
closer inspection suggests the assignments removed are entirely spurious."
Acked-by: William Irwin <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 22 Mar 2006 08:08:07 +0000 (00:08 -0800)]
[PATCH] mm: cleanup bootmem
The bootmem code added to page_alloc.c duplicated some page freeing code
that it really doesn't need to because it is not so performance critical.
While we're here, make prefetching work properly by actually prefetching
the page we're about to use before prefetching ahead to the next one (ie.
get the most important transaction started first). Also prefetch just a
single page ahead rather than leaving a gap of 16.
Jack Steiner reported no problems with SGI's ia64 simulator.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 22 Mar 2006 08:08:05 +0000 (00:08 -0800)]
[PATCH] mm: split highorder pages
Have an explicit mm call to split higher order pages into individual pages.
Should help to avoid bugs and be more explicit about the code's intention.
Signed-off-by: Nick Piggin <npiggin@suse.de> Cc: Russell King <rmk@arm.linux.org.uk> Cc: David Howells <dhowells@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mundt <lethal@linux-sh.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Chris Zankel <chris@zankel.net> Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 22 Mar 2006 08:08:03 +0000 (00:08 -0800)]
[PATCH] mm: simplify vmscan vs release refcounting
The VM has an interesting race where a page refcount can drop to zero, but it
is still on the LRU lists for a short time. This was solved by testing a 0->1
refcount transition when picking up pages from the LRU, and dropping the
refcount in that case.
Instead, use atomic_add_unless to ensure we never pick up a 0 refcount page
from the LRU, thus a 0 refcount page will never have its refcount elevated
until it is allocated again.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nick Piggin [Wed, 22 Mar 2006 08:08:00 +0000 (00:08 -0800)]
[PATCH] mm: less atomic ops
In the page release paths, we can be sure that nobody will mess with our
page->flags because the refcount has dropped to 0. So no need for atomic
operations here.
Signed-off-by: Nick Piggin <npiggin@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6 / log