Andrew Vasquez [Mon, 29 Jan 2007 18:22:23 +0000 (10:22 -0800)]
[SCSI] qla2xxx: Set correct cabling state during initialization.
Previous work to add asynchronous-scsi-scanning support
(d19044c32baadeb80e135027124a9e845c6f057c) caused peculiar
semantic changes when no cabling was attached to the HBA
whereby unneeded and intrusive 'error-handling' would take
place due to the initial link state being unset.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Lalit Chandivade [Mon, 29 Jan 2007 18:22:22 +0000 (10:22 -0800)]
[SCSI] qla2xxx: Perform implicit LOGO during fabric logout request.
Similarly to previous LOGO requests on non-24xx hardware,
perform an implicit-LOGO as to avoid the potential 2 *
R_A_TOV delay which can result during an explicit-LOGO
request.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Andrew Vasquez [Mon, 29 Jan 2007 18:22:20 +0000 (10:22 -0800)]
[SCSI] qla2xxx: Handle IRQ-0 assignments by the system.
No restriction should be placed on the IRQ number assigned
to a given ISP. Original code incorrectly assumed a
non-zero IRQ number assignment by the system. In these
circumstances the proper freeing of the IRQ (via free_irq())
would not take place.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch removes a duplicate device id from the IPR driver. Based on
the ipr.h file, I'm not so sure this was intended to be a duplicate, and
if so, the .h file should be modified to use the proper sub-device id
instead.
This was pointed out to me by Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Fri, 26 Jan 2007 22:08:52 +0000 (14:08 -0800)]
[SCSI] libsas: Handle SCSI commands that complete with failure codes
This patch moves the code that handles SAS failures out of the main EH
function and into a separate function. It also detects commands that have
no sas_task (i.e. they completed, but with error data) and sends them into
scsi_error for processing. This allows us to handle SCSI errors (and
enables auto-spinup as a side effect) instead of dropping them on the
floor and falling into an infinite loop. It also requires the
implementation of a device reset function, which the SAS failure code has
been modified to employ for REQ_DEVICE_RESET.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Fri, 26 Jan 2007 22:08:43 +0000 (14:08 -0800)]
[SCSI] libsas: Clean up discovery failure handler code
sas_rphy_delete does two things: it removes the sas_rphy from the transport
layer and frees the sas_rphy. This can be broken down into two functions,
sas_rphy_remove and sas_rphy_free; sas_rphy_remove is of interest to
sas_discover_root_expander because it calls functions that require
sas_rphy_add as a prerequisite and can fail (namely sas_discover_expander).
In that case, sas_discover_root_expander needs to be able to undo the effects
of sas_rphy_add yet leave the job of freeing the sas_rphy to the caller of
sas_discover_root_expander.
This patch also removes some unnecessary code from sas_discover_end_dev
to eliminate an unnecessary cycle of sas_notify_lldd_gone/found for SAS
devices, thus eliminating a sas_rphy_remove call (and fixing a race condition
where a SCSI target scan can come in between the gone and found call).
It also moves the sas_rphy_free calls into sas_discover_domain and
sas_ex_discover_end_dev to complement the sas_rphy_allocation via
sas_get_port_device.
This patch does not change the semantics of sas_rphy_delete.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Fri, 26 Jan 2007 22:08:41 +0000 (14:08 -0800)]
[SCSI] libsas: Fix incorrect sas_port deformation in sas_form_port
Currently, sas_form_port checks the given asd_sas_phy's sas_phy to see if
there's already a port attached. If so, the SAS addresses of the port and
the phy are compared to determine if we need to detach from the port
because the addresses don't match or if we can stop; the SAS address stored
in the sas_port reflects whatever device _was_ attached to the port/phy, and
the SAS address stored in the sas_port reflects whatever device we just
discovered. As written, the code detaches from the port if the addresses
_do_ match, and prints an error if they do _not_ match. I believe this to
be incorrect, as it seems more logical to keep the port if the addresses
match (i.e. the phy was reset but the device didn't change), and detach it
they do not (i.e. the device changed).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Take the expose_physicals flag and allow the user to select default (physicals
available via /dev/sg), exposed (physicals available via /dev/sd for
experimental reasons) and hidden (physicals blocked from all access). This
expands the functionality of the previous expose_physicals insmod parameter
which was added to support some experimental configurations.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Tue, 23 Jan 2007 23:00:30 +0000 (15:00 -0800)]
[SCSI] aacraid: rework packet support code
Received from Mark Salyzyn,
Replace all if/else packet formations with platform function calls. This is in
recognition of the proliferation of read and write packet types, and in the
need to migrate to up-and-coming packets for new products.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Tue, 23 Jan 2007 22:59:20 +0000 (14:59 -0800)]
[SCSI] aacraid: rework communication support code
Received from Mark Salyzyn,
Replace all if/else communication transports with a platform function call.
This is in recognition of the need to migrate to up-and-coming transports.
Currently the Linux driver does not support two available communication
transports provided by our products, these will be added in future patches, and
will expand the platform function set.
Signed-off-by Mark Haverkamp <markh@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Brian King [Tue, 23 Jan 2007 17:25:37 +0000 (11:25 -0600)]
[SCSI] ipr: PCI error recovery fix
Since the pci_block_user_cfg_access API was modified to track
block/unblocks, it was discovered that the ipr driver had a
path through its code (in PCI error recovery) which would unblock
when not previously blocked.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Brian King [Tue, 23 Jan 2007 17:25:23 +0000 (11:25 -0600)]
[SCSI] ipr: Remove usage of pci driver data
Since ipr handles dynamic ids, it must handle driver_data
not being set, so remove the current usage of driver_data
so it can be used for other things in future patches.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Alexis Bruemmer [Tue, 16 Jan 2007 23:36:12 +0000 (15:36 -0800)]
[SCSI] aic94xx: fix typos and update verison number
fix typos and bump version number
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Alexis Bruemmer <alexisb@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:38 +0000 (14:15 -0800)]
[SCSI] aic94xx: Scan SAS devices asynchronously
Add the necessary hooks to the aic94xx driver to support the asynchronous SCSI
device scan infrastructure.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:35 +0000 (14:15 -0800)]
[SCSI] libsas: sysfs phy control attributes should not be S_IWUGO
Allowing the phy reset controls to be world-triggerable does not seem like
a terribly good idea because SAS devices can be disrupted (and ATA devices
are really disrupted) by a phy reset. By default only root should be able
to do things like that.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:32 +0000 (14:15 -0800)]
[SCSI] aic94xx: Lock DDB read/write accesses
Extend the use of the DDB lock to include all DDB accesses, because
DDB updates now occur from multiple threads. This fixes the SMP timeout
problems that we were occasionally seeing with a x260, because the
controller got confused when the DDBs got corrupted.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:29 +0000 (14:15 -0800)]
[SCSI] aic94xx: Fix DDB and SCB initialization
Ed Chim of Adaptec informs us that the DDB registers need to be zeroed at
initialization time and that some SCB initializations need to happen even if
we don't use the SCB.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:26 +0000 (14:15 -0800)]
[SCSI] aic94xx: Match request_firmware with release_firmware
The vmalloc() blob holding the sequencer firmware wasn't being released at
module unload time, which resulted in a memory leak.
Signed-off-by: Alexis Bruemmer <alexisb@us.ibm.com> Acked-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:23 +0000 (14:15 -0800)]
[SCSI] aic94xx: Remove workqueue code from REQ_TASK_ABORT/REQ_DEVICE_RESET code
Now that task aborts and device port resets are done by the EH, we can
remove all the code that set up workqueues and such and simply call
sas_task_abort and let libsas figure things out.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:20 +0000 (14:15 -0800)]
[SCSI] libsas: Delay issuing ABORT TASK TMF until the error handler
sas_task_abort() should simply abort the upper-level SCSI command and wait
until the error handler to send the actual ABORT TASK command. By
deferring things to the EH we simplify the concurrency coordination and
eliminate some race conditions. Note that sas_task_abort has a few hooks
to handle libsas internal commands properly too.
Also rename do_sas_task_abort to __sas_task_abort just in case we really
want to abort the task *right now* and we don't have a scsi_cmnd attached
to the command. This is a hook for libata internal commands to abort.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:17 +0000 (14:15 -0800)]
[SCSI] libsas: Enable the EH strategy handler to reset a phy after a command
When a SAS LLDD needs to request a device port reset, it needs to have all
commands aborted before it can reset the port. Since commands are put on
the EH's list in the order that they were queued, the LLDD can set a "need
reset" flag in the last task to be aborted so that the EH can reset the
port after all commands are aborted.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:15 +0000 (14:15 -0800)]
[SCSI] libsas: Remove SAS_TASK_INITIATOR_ABORTED flag
This flag is no longer necessary because we push tasks to be aborted into
the EH as soon as we possibly can, and let the SCSI EH code take care of
the coordination for which this flag was used.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:12 +0000 (14:15 -0800)]
[SCSI] aic94xx: Don't eat TMF_QUERY_TASK results
In this driver, TMF_QUERY_TASK translates to QUERY_SSP_TASK. The
sequencer, it seems, is perfectly happy sending us a SSP response, which
this function promptly "converts" into TMF_RESP_FUNC_FAILED. This leads to
the SAS EH making bad decisions based on bad data, so we should not perform
the conversion in this case.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:06 +0000 (14:15 -0800)]
[SCSI] aic94xx: Set lldd_max_execute_num in sas_ha
The aic94xx module has a parameter that looks like it should set
lldd_max_execute_num in the sas_ha, but it never sets this value. Either
we should set it or remove the parameter. This allows us to enable task
collector mode for this driver, though it is still off by default.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:03 +0000 (14:15 -0800)]
[SCSI] libsas: Destroy the task collector thread after releasing ports
If we use task collector mode, we can end up destroying the task collector
thread before we release the ports, which is bad if a port release causes
a disk I/O (such as cache flushing).
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:15:00 +0000 (14:15 -0800)]
[SCSI] libsas: Reset timer on taskless scsi_cmnds in sas_scsi_timed_out
Every so often, a scsi_cmnd will time out, and the libsas timeout handler
will discover that the scsi_cmnd does not have a sas_task attached to it.
This can happen in two cases: (1) the scsi_cmnd actually made it through
libsas to the HBA and is now going through scsi_done, or (2) the
scsi_cmnd has been held up (host lock, slab alloc, etc) and libsas has
not yet attached a sas_task. In both cases, it is safe to ask SCSI for
more time to process the command via EH_RESET_TIMER; we cannot blindly
return EH_HANDLED because if (2) happens, we could end up calling
scsi_done while another CPU is heading towards sas_queuecommand, which
causes slab corruption when sas_task_done updates the freed scsi_cmnd.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:14:57 +0000 (14:14 -0800)]
[SCSI] libsas: Add a sysfs knob to enable/disable a phy
This patch lets a user arbitrarily enable or disable a phy via sysfs.
Potential applications include shutting down a phy to replace one
lane of wide port, and (more importantly) providing a method for the
libata SATL to control the phy.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:14:55 +0000 (14:14 -0800)]
[SCSI] libsas: Don't give scsi_cmnds to the EH if they never made it to the SAS LLDD or have already returned
On a system with many SAS targets, it appears possible that a scsi_cmnd
can time out without ever making it to the SAS LLDD or at the same time
that a completion is occurring. In both of these cases, telling the
LLDD to abort the sas_task makes no sense because the LLDD won't know
about the sas_task; what we really want to do is to increase the timer.
Note that this involves creating another sas_task bit to indicate
whether or not the task has been sent to the LLDD; I could have
implemented this by slightly redefining SAS_TASK_STATE_PENDING, but
this way seems cleaner.
This second version amends the aic94xx portion to set the
TASK_AT_INITIATOR flag for all sas_tasks that were passed to
lldd_execute_task.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:14:52 +0000 (14:14 -0800)]
[SCSI] libsas: Clean up rphys/port dev list after a discovery error on an expander
sas_get_port_device assigns a rphy to a domain device in anticipation
of finding a disk. When a discovery error occurs in
sas_discover_{sata,sas,expander}*, however, we need to clean up that
rphy and the port device list so that we don't GPF. In addition, we
need to check the result of the second sas_notify_lldd_dev_found.
This patch seems ok on a x260, x366 and x206m.
This patch fixes up sas_expander.c separately because jejb has some
cleanup patches of his own that are a prerequisite.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Thu, 11 Jan 2007 22:14:49 +0000 (14:14 -0800)]
[SCSI] libsas: Clean up rphys/port dev list after a discovery error.
sas_get_port_device assigns a rphy to a domain device in anticipation
of finding a disk. When a discovery error occurs in
sas_discover_{sata,sas,expander}*, however, we need to clean up that
rphy and the port device list so that we don't GPF. In addition, we
need to check the result of the second sas_notify_lldd_dev_found.
This patch seems ok on a x260, x366 and x206m.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Seokmann Ju [Tue, 9 Jan 2007 19:37:52 +0000 (11:37 -0800)]
[SCSI] qla2xxx: correct locking while call starget_for_each_device()
Removed spin_unlock_irq()/spin_lock_irq() pairs surrounding
starget_for_each_device() calls.
As Matthew W. pointed out, starget_for_each_device() can be called under
a spinlock being held.
The change has been tested and verified on qla2xxx.ko module.
Thanks Matthew W. and Hisashi H. for help.
Signed-off-by: Andrew Vasquez <Andrew.vasquez@qlogic.com> Signed-off-by: Seokmann Ju <Seokmann.ju@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Kurt Garloff [Tue, 9 Jan 2007 01:28:54 +0000 (02:28 +0100)]
[SCSI] scsi_scan message cosmetic error
Hi,
Minor typo ...
In my first iteration of patches (that got merged), the
BLIST_ATTACH_PQ3 actually had the value 0x800000, but that
got changed later to avoid conflicts. This piece must have
been overlooked.
You could obviously do something like %x and then add the
bitflags, but that looks overkill for something that does
not tend to change.
Please merge.
(Patch applied against latest 2.6.20rc version that I tested.)
From: Kurt Garloff <kurt@garloff.de>
Subject: [SCSI SCAN] Fix logging message for PQ3 devices
The blacklist flags BLIST_ATTACH_PQ3 has value 0x1000000,
not 0x800000.
Signed-off-by: Kurt Garloff <garloff@suse.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Randy Dunlap [Wed, 10 Jan 2007 05:40:52 +0000 (21:40 -0800)]
[SCSI] megaraid: more kernel-doc fixes
More megaraid kernel-doc fixes.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Sumant Patro <sumantp@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Randy Dunlap [Sat, 6 Jan 2007 06:41:48 +0000 (22:41 -0800)]
[SCSI] megaraid: fix kernel-doc
kernel-doc modifications:
- change "@param var" notation to @var;
- change function/description separator from ':' to '-';
- change var/description separator from '-' to ':';
- fix a few doc. typos;
- don't use kernel-doc /** lead-in when the doc. block is not kernel-doc;
- use Linux common */ ending comment format instead of **/;
- use correct function parameter names;
- place function parameters immediately after the function short description;
- place kernel-doc immediately before its function or macro;
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Acked-by: Sumant Patro <sumantp@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Sumant Patro [Fri, 5 Jan 2007 15:10:09 +0000 (07:10 -0800)]
[SCSI] megaraid_{mm,mbox}: init fix for kdump
1. Changes in Initialization to fix kdump failure.
Send SYNC command on loading.
This command clears the pending commands in the adapter
and re-initialize its internal RAID structure.
Without this change, megaraid driver either panics or fails to
initialize the adapter during kdump's second kernel boot
if there are pending commands or interrupts from other devices
sharing the same IRQ.
2. Authors email-id domain name changed from lsil.com to lsi.com.
Also modified the MODULE_AUTHOR to megaraidlinux@lsi.com
Signed-off-by: Sumant Patro <sumant.patro@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Douglas Gilbert [Fri, 5 Jan 2007 05:05:25 +0000 (00:05 -0500)]
[SCSI] scsi_debug: error processing
After discussions in the thread titled:
[PATCH] scsi_debug: illegal blocking memory allocation
here is a patch containing the discussed fix and some other
fixes and additions. The patch is against lk 2.6.20-rc3 .
The version is bumped to 1.81 .
ChangeLog:
- Change several GFP_KERNEL allocations to GFP_ATOMIC
as they can be called from queuecommand() context
- check above allocation returns and if out of memory
report DID_REQUEUE in two cases, DID_NO_CONNECT in
another, and fail slave configure() in another
- add support for WRITE BUFFER command
- add aborted_command error injection support
(opts mask 0x10), similar mechanism to
recovered_error injection.
Signed-off-by: Douglas Gilbert <dougg@torque.net> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Douglas Gilbert [Fri, 5 Jan 2007 04:48:54 +0000 (23:48 -0500)]
[SCSI] mptctl for mptsas
This patch makes the mptctl pass through available if
the mptsas driver is selected. Without this patch
if mptsas is the only fusion driver chosen, then
the mptctl is not presented as an option.
smp_utils uses the mptctl driver to pass SAS SMP
functions through a MPT SAS HBA.
Signed-off-by: Douglas Gilbert <dougg@torque.net> Acked-by: "Moore, Eric" <Eric.Moore@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi_retry_command only has a single caller, so there is no point
in having this function. Additionally the memset of the sense
buffer it does is entirely superflous as scsi_request_fn already
calls scsi_init_cmd_errh to perform this memset before the command
is reissued.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a patch, which allows not only disabling bursting but to specify
different burst lenghts. This feature is needed to get the 53c700 driver
working for the onboard SCSI controller of SNI RM machines, which only
work reliably with a 4 word burst length.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Jens Axboe [Fri, 12 Jan 2007 11:20:26 +0000 (12:20 +0100)]
[PATCH] blktrace: only add a bounce trace when we really bounce
Currently we issue a bounce trace when __blk_queue_bounce() is called,
but that merely means that the device has a lower dma mask than the
higher pages in the system. The bio itself may still be lower pages. So
move the bounce trace into __blk_queue_bounce(), when we know there will
actually be page bouncing.
Linus Torvalds [Fri, 12 Jan 2007 02:26:28 +0000 (18:26 -0800)]
Merge branch 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid:
HID: Fix DRIVER_DESC macro
HID: mousepoll parameter makes no sense for generic HID
HID: tiny patch to remove a kmalloc cast
HID: fix mappings for DiNovo Edge Keyboard - Logitech USB BT receiver
Linus Torvalds [Fri, 12 Jan 2007 02:25:44 +0000 (18:25 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
Revert "ACPI: ibm-acpi: make non-generic bay support optional"
ACPI: update MAINTAINERS
ACPI: schedule obsolete features for deletion
ACPI: delete two spurious ACPI messages
ACPI: rename cstate_entry_s to cstate_entry
ACPI: ec: enable printk on cmdline use
ACPI: Altix: ACPI _PRT support
Daniel Ritz [Fri, 8 Dec 2006 17:07:01 +0000 (18:07 +0100)]
[PATCH] PCMCIA: fix drivers broken by recent cleanup
Setting .ConfigBase and .Present is now done at the pcmcia core.
The driver cleanup missed a few places where the driver did set .Present
to PRESENT_OPTION and later to the values from the CIS. Setting to
PRESENT_OPTION now overrides the values from the CIS. So just remove
those lines.
Andrew Morton [Thu, 11 Jan 2007 07:15:45 +0000 (23:15 -0800)]
[PATCH] FD_ZERO build fix
unionfs managed to hit this on s390. Some architectures use __ptr_t in their
FD_ZERO implementation. We don't have a __ptr_t. Switch them over to plain
old void*.
Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "Luck, Tony" <tony.luck@intel.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Josef 'Jeff' Sipek <jsipek@cs.sunysb.edu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michael Buesch [Thu, 11 Jan 2007 07:15:43 +0000 (23:15 -0800)]
[PATCH] Fix HWRNG built-in initcalls priority
This changes all HWRNG driver initcalls to module_init(). We must probe
the RNGs after the major kernel subsystems are already up and running (like
PCI).
This fixes Bug 7730.
http://bugzilla.kernel.org/show_bug.cgi?id=7730
Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: Jan Beulich <jbeulich@novell.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan Beulich [Thu, 11 Jan 2007 07:15:41 +0000 (23:15 -0800)]
[PATCH] intel-rng workarounds
Add a load option to intel-rng to allow skipping the FWH detection,
necessary in case the BIOS has locked read-only the firmware hub space.
Also prevent any attempt to write to firmware space if it cannot be write
enabled (apparently caused hangs on some systems not having an FWH and thus
also not having a respective RNG).
Signed-off-by: Jan Beulich <jbeulich@novell.com> Signed-off-by: Michael Buesch <mb@bu3sch.de> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Chinner [Thu, 11 Jan 2007 07:15:41 +0000 (23:15 -0800)]
[PATCH] Revert bd_mount_mutex back to a semaphore
Revert bd_mount_mutex back to a semaphore so that xfs_freeze -f /mnt/newtest;
xfs_freeze -u /mnt/newtest works safely and doesn't produce lockdep warnings.
(XFS unlocks the semaphore from a different task, by design. The mutex
code warns about this)
Signed-off-by: Dave Chinner <dgc@sgi.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Miller [Thu, 11 Jan 2007 07:15:40 +0000 (23:15 -0800)]
[PATCH] really fix funsoft driver
Fix void cast and re-enable on sparc.
Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trond Myklebust [Thu, 11 Jan 2007 07:15:39 +0000 (23:15 -0800)]
[PATCH] NFS: Fix race in nfs_release_page()
NFS: Fix race in nfs_release_page()
invalidate_inode_pages2() may find the dirty bit has been set on a page
owing to the fact that the page may still be mapped after it was locked.
Only after the call to unmap_mapping_range() are we sure that the page
can no longer be dirtied.
In order to fix this, NFS has hooked the releasepage() method and tries
to write the page out between the call to unmap_mapping_range() and the
call to remove_mapping(). This, however leads to deadlocks in the page
reclaim code, where the page may be locked without holding a reference
to the inode or dentry.
Fix is to add a new address_space_operation, launder_page(), which will
attempt to write out a dirty page without releasing the page lock.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Also, the bare SetPageDirty() can skew all sort of accounting leading to
other nasties.
[akpm@osdl.org: cleanup] Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Vivek Goyal [Thu, 11 Jan 2007 07:15:36 +0000 (23:15 -0800)]
[PATCH] i386: sched_clock using init data tsc_disable fix
o sched_clock() a non-init function is using init data tsc_disable. This
is flagged by MODPOST on i386 if CONFIG_RELOCATABLE=y
WARNING: vmlinux - Section mismatch: reference to .init.data:tsc_disable from .text between 'sched_clock' (at offset 0xc0109d58) and 'tsc_update_callback'
Vivek Goyal [Thu, 11 Jan 2007 07:15:35 +0000 (23:15 -0800)]
[PATCH] Kdump documentation update
o Kdump documentation update.
- Update details for using relocatable kernel.
- Start using kexec-tools-testing release as it is latest and old
kexec-tools can't load relocatable bzImage file.
- Also add kdump on ia64 specific details.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com> Cc: Horms <horms@verge.net.au> Cc: Mohan Kumar M <mohan@in.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Gautham R Shenoy [Thu, 11 Jan 2007 07:15:34 +0000 (23:15 -0800)]
[PATCH] Change cpu_up and co from __devinit to __cpuinit
Compiling the kernel with CONFIG_HOTPLUG = y and CONFIG_HOTPLUG_CPU = n
with CONFIG_RELOCATABLE = y generates the following modpost warnings
WARNING: vmlinux - Section mismatch: reference to .init.data: from
.text between '_cpu_up' (at offset 0xc0141b7d) and 'cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.data: from
.text between '_cpu_up' (at offset 0xc0141b9c) and 'cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.text:__cpu_up
from .text between '_cpu_up' (at offset 0xc0141bd8) and 'cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.data: from
.text between '_cpu_up' (at offset 0xc0141c05) and 'cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.data: from
.text between '_cpu_up' (at offset 0xc0141c26) and 'cpu_up'
WARNING: vmlinux - Section mismatch: reference to .init.data: from
.text between '_cpu_up' (at offset 0xc0141c37) and 'cpu_up'
This is because cpu_up, _cpu_up and __cpu_up (in some architectures) are
defined as __devinit
AND
__cpu_up calls some __cpuinit functions.
Since __cpuinit would map to __init with this kind of a configuration,
we get a .text refering .init.data warning.
This patch solves the problem by converting all of __cpu_up, _cpu_up
and cpu_up from __devinit to __cpuinit. The approach is justified since
the callers of cpu_up are either dependent on CONFIG_HOTPLUG_CPU or
are of __init type.
Thus when CONFIG_HOTPLUG_CPU=y, all these cpu up functions would land up
in .text section, and when CONFIG_HOTPLUG_CPU=n, all these functions would
land up in .init section.
Tested on a i386 SMP machine running linux-2.6.20-rc3-mm1.
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com> Cc: Vivek Goyal <vgoyal@in.ibm.com> Cc: Mikael Starvik <starvik@axis.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Kyle McMartin <kyle@mcmartin.ca> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Hansen [Thu, 11 Jan 2007 07:15:30 +0000 (23:15 -0800)]
[PATCH] Fix sparsemem on Cell
Fix an oops experienced on the Cell architecture when init-time functions,
early_*(), are called at runtime. It alters the call paths to make sure
that the callers explicitly say whether the call is being made on behalf of
a hotplug even, or happening at boot-time.
It has been compile tested on ppc64, ia64, s390, i386 and x86_64.
Acked-by: Arnd Bergmann <arndb@de.ibm.com> Signed-off-by: Dave Hansen <haveblue@us.ibm.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Acked-by: Andy Whitcroft <apw@shadowen.org> Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Brice Goglin [Thu, 11 Jan 2007 07:15:29 +0000 (23:15 -0800)]
[PATCH] increment pos before looking for the next cap in __pci_find_next_ht_cap
While testing 2.6.20-rc3 on a machine with some CK804 chipsets, we noticed
that quirk_nvidia_ck804_msi_ht_cap() was not detecting HT MSI capabilities
anymore. It is actually caused by the MSI mapping on the root chipset
being the 2nd HT capability in the chain. pci_find_ht_capability() does
not seem to find anything but the first HT cap correctly, because it
forgets to increment the position before looking for the next cap. The
following patch seems to fix it.
At least, this proves that having a ttl is good idea since the machine
would have been stucked in an infinite loop if we didn't have a ttl :)
We have to pass pos + PCI_CAP_LIST_NEXT to __pci_find_next_cap_ttl to
get the next HT cap instead of the same one again.
Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Andrew J. Gallatin <gallatin@myri.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Nathan Lynch [Thu, 11 Jan 2007 07:15:28 +0000 (23:15 -0800)]
[PATCH] sched: tasks cannot run on cpus onlined after boot
Commit 5c1e176781f43bc902a51e5832f789756bff911b ("sched: force /sbin/init
off isolated cpus") sets init's cpus_allowed to a subset of cpu_online_map
at boot time, which means that tasks won't be scheduled on cpus that are
added to the system later.
Make init's cpus_allowed a subset of cpu_possible_map instead. This should
still preserve the behavior that Nick's change intended.
Thanks to Giuliano Pochini for reporting this and testing the fix:
Linus Torvalds [Fri, 12 Jan 2007 02:18:04 +0000 (18:18 -0800)]
Don't put "linux_banner" in the .init section
It might save a few bytes after bootup, but it causes the string to be
linked in at the end of the final vmlinux image, which defeats the whole
point of doing all this, namely allowing some broken user-space binaries
to search for the kernel version string in the kernel binary.
So just remove the __init specifier.
Cc: Olaf Hering <olaf@aepfle.de> Cc: Jean Delvare <khali@linux-fr.org> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Andrey Borzenkov <arvidjaar@mail.ru> Cc: Andrew Morton <akpm@osdl.org> Acked-by: Andy Whitcroft <apw@shadowen.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ACPI_BAY has not been merged into mainline yet, so the changes to ibm-acpi
related Kconfig entries that depend on ACPI_BAY were permanently disabling
ibm-acpi bay support. This is a serious regression for ThinkPad users.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Thu, 11 Jan 2007 02:06:14 +0000 (18:06 -0800)]
Merge branch 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6:
[PATCH] x86-64: Fix warnings in ia32_aout.c
[PATCH] i386: Convert some functions to __init to avoid MODPOST warnings
[PATCH] i386: Fix memory hotplug related MODPOST generated warning
[PATCH] x86-64: tighten up printks
[PATCH] x86-64: - Ignore long SMI interrupts in clock calibration
[PATCH] x86-64: pci quirks MODPOST warning fix
[PATCH] x86-64: Modpost whitelist reference to more symbols (pattern 3)
[PATCH] x86-64: modpost add more symbols to whitelist pattern2
[PATCH] i386: make apic probe function non-init
[PATCH] i386: cpu hotplug/smpboot misc MODPOST warning fixes
[PATCH] x86-64: Use different constraint for gcc < 4.1 in bitops.h
[PATCH] x86-64: Make noirqdebug_setup function non init to fix modpost warning
[PATCH] i386: Update defconfig
[PATCH] x86-64: Update defconfig
Andi Kleen [Thu, 11 Jan 2007 00:52:45 +0000 (01:52 +0100)]
[PATCH] x86-64: Fix warnings in ia32_aout.c
Fix
linux/arch/x86_64/ia32/ia32_aout.c: In function ‘create_aout_tables’:
linux/arch/x86_64/ia32/ia32_aout.c:244: warning: cast from pointer to integer of different size
linux/arch/x86_64/ia32/ia32_aout.c:253: warning: cast from pointer to integer of different size
with gcc 4.3 Signed-off-by: Andi Kleen <ak@suse.de>
Vivek Goyal [Thu, 11 Jan 2007 00:52:44 +0000 (01:52 +0100)]
[PATCH] i386: Convert some functions to __init to avoid MODPOST warnings
o Some functions which should have been in init sections as they are called
only once. Put them in init sections. Otherwise MODPOST generates warning
as these functions are placed in .text and they end up accessing something
in init sections.
WARNING: vmlinux - Section mismatch: reference to .init.text:migration_init
from .text between 'do_pre_smp_initcalls' (at offset 0xc01000d1) and
'run_init_process'
Jack Steiner [Thu, 11 Jan 2007 00:52:44 +0000 (01:52 +0100)]
[PATCH] x86-64: - Ignore long SMI interrupts in clock calibration
Ensure that no SMI interrupts occur between the read of the HPET & TSC
in the clock calibration loop.
I noticed that a 2.66GHz system incorrectly detected the processor
clock speed about 1/7 of the time:
time.c: Detected 2660.005 MHz processor. (most of the time)
time.c: Detected 2988.203 MHz processor. (sometime)
The problem is caused by an SMI interrupt occuring in hpet_calibrate_tsc()
between the read of the HPET & TSC. Prior to switching the BIOS into
ACPI mode, it appears that every 27msec an SMI interrupt occurs. The
SMI interrupt takes 4.8 msec to process.
Note: On my test system, TICK_MIN had to be >380. I picked 5000
to minimize risk of having a value that is too small for other
platforms.
Vivek Goyal [Thu, 11 Jan 2007 00:52:44 +0000 (01:52 +0100)]
[PATCH] x86-64: pci quirks MODPOST warning fix
o MODPOST generates warnings for i386 if kernel is compiled with
CONFIG_RELOCATABLE=y
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc_ich6' (at offset 0xc0217d58) and 'quirk_cardbus_legacy'
WARNING: vmlinux - Section mismatch: reference to .init.data: from .text between 'asus_hides_smbus_lpc' (at offset 0xc0217fd9) and 'pci_match_id'
o Two quirk functions which are non __init, are accessing data which is
of type __init.
Vivek Goyal [Thu, 11 Jan 2007 00:52:44 +0000 (01:52 +0100)]
[PATCH] x86-64: Modpost whitelist reference to more symbols (pattern 3)
o MODPOST generates warning on i386 if kernel is compiled with
CONFIG_RELOCATABLE=y.
WARNING: vmlinux - Section mismatch: reference to .init.text:__init_begin from .text between 'free_initmem' (at offset 0xc0114fd3) and 'do_test_wp_bit'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'core_kernel_text' (at offset 0xc012aeae) and 'kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'core_kernel_text' (at offset 0xc012aeb7) and 'kernel_text_address'
WARNING: vmlinux - Section mismatch: reference to .init.text:_sinittext from .text between 'get_symbol_pos' (at offset 0xc0135776) and 'reset_iter'
WARNING: vmlinux - Section mismatch: reference to .init.text:_einittext from .text between 'get_symbol_pos' (at offset 0xc013577d) and 'reset_iter'
o These symbols (__init_begin, _sinittext, _einittext) belong to init
section and generally represent a section boundary. These are special
symbols in the sense that their size is zero and no memory is allocated
for them in init section. Their addr and value are same. So even if
we free the init section, it is ok to reference them.
o Whitelist access to such select symbols in MODPOST.
Vivek Goyal [Thu, 11 Jan 2007 00:52:44 +0000 (01:52 +0100)]
[PATCH] x86-64: modpost add more symbols to whitelist pattern2
o MODPOST generates warning for i386 if compiled with CONFIG_RELOCATABLE=y
and serial console support is enabled.
o Serial console setup function, serial8250_console_setup(), is a non __init
function and it calls functions which are of type __init().
(uart_parse_options() and uart_set_options()). Assuming, setup will
be called during init time, changing serial8250_console_setup() to __init.
o Adding one more pattern to modpost whitelist. Console drivers might
have *_console structures containing references to setup functions which
can be of __init type. Don't generate warnings for those.
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'serial8250_console' (at offset 0xc05a33d8) and 'serial8250_reg'
Vivek Goyal [Thu, 11 Jan 2007 00:52:44 +0000 (01:52 +0100)]
[PATCH] i386: make apic probe function non-init
o struct genapic contains pointer to probe() function which is of type
__init. Hence MODPOST generates warning if kernel is compiled with
CONFIG_RELOCATABLE=y for i386.
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'apic_summit' (at offset 0xc058b504) and 'apic_bigsmp'
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'apic_bigsmp' (at offset 0xc058b5a4) and 'cpu.4471'
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'apic_es7000' (at offset 0xc058b644) and 'apic_default'
WARNING: vmlinux - Section mismatch: reference to .init.text: from .data between 'apic_default' (at offset 0xc058b6e4) and 'interrupt'
o One of the possible options is to put special case check in MODPOST to
not emit warnings for this case but I think it is not a very good option
in terms of maintenance.
o Another option is to make probe() function non __init. Anyway this function
is really small so not freeing this memory after init is not a big deal.
Secondly, from a programming perspective, probably genapic should not
provide pointers to functions which have been freed as genapic is non
__init and is used even after initialization is complete.
projects / linux-2.6 / log