Paul Mundt [Sat, 28 Jul 2007 14:45:43 +0000 (23:45 +0900)]
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
BLK_DEV_BSG was added outside of the if BLOCK check, which allows it to
be enabled when CONFIG_BLOCK=n. This leads to many screenlengths of
errors, starting with a parse error on the request_queue_t definition.
Obviously this wasn't intended for CONFIG_BLOCK=n usage, so just move the
option back in to the block.
Caught with a randconfig on sh.
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Jens Axboe <jens.axboe@oracle.com> Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Salyzyn, Mark [Fri, 27 Jul 2007 14:29:26 +0000 (10:29 -0400)]
[SCSI] aacraid: fix Sunrise Lake reset handling
The patch is *much* smaller than the description. I am attempting to
answer to those that want to understand an issue that was reported in
May this year.
If a Sunrise Lake based card that requires an alternate reset mechanism
is set up to ignore the commanded IOP_RESET it reports 0x00000010
(IOP_RESET ignored) instead of 0x3803000F (use alternate reset mechanism
to reset all cores), and thus the reset platform function decides to
switch to IOP_RESET_ALWAYS because the reset platform function
parameters indicate that we *need* to reset the card. IOP_RESET_ALWAYS
then responds with the 0x3803000F return code, but alas we treat this as
an error instead of using the alternate reset mechanism (put a 0x03 into
the register offset 0x38). The reset fails, but the fact that the
IOP_RESET_ALWAYS command was issued has put the card in a purposeful
shutdown state in preparation for the alternate hardware reset to be
applied. Yuck.
IOP_RESET is ignored in internal production cards, typically to ensure
that we catch all adapter lockup issues without the driver progressing
further, so this would not appear to be a field issue and thus this
patch was destined to be only in the internal Adaptec source tree.
IOP_RESET_ALWAYS is reserved for
kexec/kdump/FirmwareUpdate/AutomatedTestFrames so we did not function as
expected in any case. Also in the past we have had OEMs specifically
request that cards not be resetable after a BlinkLED/FirmwareAssert for
one reason or another and To head off the possibility that the Sunrise
Lake based cards would suffer a similar fate, we propose the enclosed
fix.
Yinghai Lu of SUN had a pre-production card with IOP_RESET disabled when
he reported an issue to the linux kernel list back in May regarding a
kexec problem resulting from this reset being ignore. His fix was to
update the Firmware to one that did not ignore the IOP_RESET. Previous
kernels did not attempt to reset the adapter and that is why it surfaced
as a regression in his hands.
The current list of aacraid based cards that use Sunrise Lake:
9005:0285:9005:02b5 Adaptec 5445
9005:0285:9005:02b6 Adaptec 5805
9005:0285:9005:02b7 Adaptec 5085
9005:0285:9005:02c3 Adaptec 51205
9005:0285:9005:02c4 Adaptec 51605
9005:0285:9005:02ce Adaptec 51245
9005:0285:9005:02cf Adaptec 51645
9005:0285:9005:02d0 Adaptec 52445
9005:0285:9005:02d1 Adaptec 5405
9005:0285:9005:02b8 ICP ICP5445SL
9005:0285:9005:02b9 ICP ICP5085SL
9005:0285:9005:02ba ICP ICP5805SL
9005:0285:9005:02c5 ICP ICP5125SL
9005:0285:9005:02c6 ICP ICP5165SL
9005:0285:108e:7aac SUN STK RAID REM
9005:0285:108e:0286 SUN STK RAID INT
9005:0285:108e:0287 SUN STK RAID EXT
9005:0285:108e:7aae SUN STK RAID EM
All of these are publicly released with IOP_RESET enabled. So there is
no immediate need for this patch.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Salyzyn, Mark [Fri, 27 Jul 2007 13:48:49 +0000 (09:48 -0400)]
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
Customer running an application that issues SYNCHRONIZE_CACHE calls
directly noticed the broad stroke of the current implementation in the
aacraid driver resulting in multiple applications feeding I/O to the
storage causing the issuing application to stall for long periods of
time. By only waiting for the current WRITE commands, rather than all
commands, to complete; and those that are in range of the
SYNCHRONIZE_CACHE call that would associate more tightly with the
issuing application before telling the Firmware to flush it's dirty
cache, we managed to reduce the stalling. The Firmware itself still
flushes all the dirty cache associated with the array ignoring the
range, it just does so in a more timely manner.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Matthew Wilcox [Thu, 26 Jul 2007 14:56:23 +0000 (10:56 -0400)]
[SCSI] advansys: lindent and other large, uninteresting changes
- Run Lindent
- Move advansys_detect and advansys_release to the end of the file
- Split advansys_board_found out of advansys_detect
- Rename a few variables, such as shp to shost and pci_devp to pdev
- Turn STATIC into static
Signed-off-by: Matthew Wilcox <matthew@wil.cx> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Wide transfers are required for every setting of PPR apart from QAS.
It seems the DV code starts at the minimum, which turns on DT and Wide
regardless of the setting of max_width. Redo the PPR and period
setting routines to respect max_width (i.e. start at period = 10 if it
is zero).
This fixes bugzilla 8366
Acked-by: "Freels, James D." <freelsjd@ornl.gov> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Seokmann Ju [Thu, 26 Jul 2007 20:43:34 +0000 (13:43 -0700)]
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
This is a patch to fix 'segmentation fault' issue which was initiated
by Richard Lary <rlary@us.ibm.com>. Thanks again Richard.
- on following sysfs attritute function, changes have made so that both
count and offset input parameters are honored by the functions.
= qla2x00_sysfs_read_nvram()
= qla2x00_sysfs_read_vpd()
- made changes so that NVRAM data to be cached to minimize H/W accesses
during agent querying of the driver's.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Salyzyn, Mark [Thu, 26 Jul 2007 18:20:02 +0000 (14:20 -0400)]
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
Minor unimportant cuttings from the floor bundled in with a version
stamp update. Only controversial change is the dropping of Alan Cox
copyright on the nark.c module since that file has no code written by
him in it.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Thu, 26 Jul 2007 17:46:47 +0000 (12:46 -0500)]
[SCSI] iscsi_tcp: Turn off bounce buffers
It was found by LSI that on setups with large amounts of memory
we were bouncing buffers when we did not need to. If the iscsi tcp
code touches the data buffer (or a helper does),
it will kmap the buffer. iscsi_tcp also does not interact with hardware,
so it does not have any hw dma restrictions. This patch sets the bounce
buffer settings for our device queue so buffers should not be bounced
because of a driver limit.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Thu, 26 Jul 2007 17:46:48 +0000 (12:46 -0500)]
[SCSI] libiscsi: fix cmd seqeunce number checking
We should not be checking the cmd windown for just handling r2t responses.
And if the window closes in on us, always have scsi-ml requeue the command
from our queuecommand function.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Thu, 26 Jul 2007 17:46:46 +0000 (12:46 -0500)]
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
This prevents the iscsi modules from being unloaded while
there are active mounts from an iscsi target.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com> Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Thu, 26 Jul 2007 17:46:45 +0000 (12:46 -0500)]
[SCSI] libiscsi: make sure session is not blocked when removing host
When we logout we block the session since we are not taking any more
commands, but when we call remove host we want to make sure any
IO that got queued up and blocked gets failed upwards quickly, so
we unblock the session and fail it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We also need to fix sym53c8xx only to bind to the PCI ID if it is of
device class PCI_CLASS_STORAGE_SCSI (otherwise it will be the cpqarray
RAID device).
Signed-off-by: Chip Coldwell <coldwell@redhat.com> Cc: Matthew Wilcox <willy@debian.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Mon, 23 Jul 2007 14:53:51 +0000 (09:53 -0500)]
[SCSI] bsg: fix unused variable warnings for BLK_DEV_BSG=n
Just using #defines for the
bsg_register_queue()/bsg_unregister_queue() can cause undefined
variables when they're defined to nothing. Use dummy inline functions
instead.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Darrick J. Wong [Tue, 24 Jul 2007 16:33:49 +0000 (09:33 -0700)]
[SCSI] libsas: SMP request handler shouldn't crash when rphy is NULL
sas_smp_handler crashes when smp utils are used with an aic94xx host
because certain devices (the sas_host itself, specifically) lack rphy
structures. No rphy means no SMP target support, but we shouldn't crash
here.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Alan Cox [Mon, 23 Jul 2007 13:51:05 +0000 (14:51 +0100)]
[SCSI] aacraid: Fix security hole
On the SCSI layer ioctl path there is no implicit permissions check for
ioctls (and indeed other drivers implement unprivileged ioctls). aacraid
however allows all sorts of very admin only things to be done so should
check.
Signed-off-by: Alan Cox <alan@redhat.com> Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The recent 9p commit: bd238fb431f31989898423c8b6496bc8c4204a86 that
supposedly only moved files also introduced a new 9p sysctl interface
that did not properly register it's sysctl binary numbers.
And since it was only for debugging clearly did not need a binary fast
path in any case. So this patch just remove the binary numbers.
See Documentation/sysctl/ctl_unnumbered.txt for more details.
While I was at it I cleaned up the sysctl initializers a little as
well so there is less to read.
Cc: Latchesar Ionkov <lucho@ionkov.net> Cc: Eric Van Hensbergen <ericvh@gmail.com> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Support small QP queues
IB/ehca: Make internal_create/destroy_qp() static
IB/ehca: Move ehca2ib_return_code() out of line
IB/ehca: Generate async event when SRQ limit reached
IB/ehca: Support large page MRs
IB/mlx4: Fix error path in create_qp_common()
mlx4_core: Change command token on timeout
IB/mthca: Change command token on timeout
IB/ipath: Remove ipath_layer dead code
IB/mlx4: Fix leaks in __mlx4_ib_modify_qp
Al Viro [Sat, 21 Jul 2007 22:29:12 +0000 (23:29 +0100)]
take declarations of enable_irq() et.al. to linux/interrupt.h
Now that the last inlined instances are gone, all that is left to do
is turning disable_irq_nosync on arm26 and m68k from defines to aliases
and we are all set - we can make these externs in linux/interrupt.h
uncoditional and kill remaining instances in asm/irq.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
James Bottomley [Sun, 22 Jul 2007 18:15:55 +0000 (13:15 -0500)]
[SCSI] libsas: make ATA functions selectable by a config option
Not everyone wants libsas automatically to pull in libata. This patch
makes the behaviour configurable, so you can build libsas with or
without ATA support.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Convert from struct class_device to struct device
leds: leds-gpio for ngw100
leds: Add warning printks in error paths
leds: Fix trigger unregister_simple if register_simple fails
leds: Use menuconfig objects II - LED
leds: Teach leds-gpio to handle timer-unsafe GPIOs
leds: Add generic GPIO LED driver
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
leds: cr_bllcd.c: build fix
backlight: Convert from struct class_device to struct device
backlight: Fix order of Kconfig entries
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Clean up duplicate includes in drivers/macintosh/
[POWERPC] Quiet section mismatch warning on pcibios_setup
[POWERPC] init and exit markings for hvc_iseries
[POWERPC] Quiet section mismatch in hvc_rtas.c
[POWERPC] Constify of_platform_driver match_table
[POWERPC] hvcs: Make some things static and const
[POWERPC] Constify of_platform_driver name
[POWERPC] MPIC protected sources
[POWERPC] of_detach_node()'s device node argument cannot be const
[POWERPC] Fix ARCH=ppc builds
[POWERPC] mv64x60: Use mutex instead of semaphore
[POWERPC] Allow smp_call_function_single() to current cpu
[POWERPC] Allow exec faults on readable areas on classic 32-bit PowerPC
[POWERPC] Fix future firmware feature fixups function failure
[POWERPC] fix showing xmon help
[POWERPC] Make xmon_write accept a const buffer
[POWERPC] Fix misspelled "CONFIG_CHECK_CACHE_COHERENCY" Kconfig option.
[POWERPC] cell: CONFIG_SPE_BASE is a typo
Al Viro [Sun, 22 Jul 2007 09:59:06 +0000 (10:59 +0100)]
fix broken handling of port=... in NFS option parsing
Obviously broken on little-endian; fortunately, the option is not
frequently used...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ Hey, sparse is wonderful, but even better than sparse is having people
like Al that actually _run_ it and fix bugs using it. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (77 commits)
ACPI: Populate /sys/firmware/acpi/tables/
ACPI: create CONFIG_ACPI_DEBUG_FUNC_TRACE
ACPI: update ACPI proc I/F removal schedule
ACPI: update feature-removal-schedule.txt, /sys/firmware/acpi/namespace is gone
ACPI: export ACPI events via acpi_mc_group multicast group
ACPI: fix empty macros found by -Wextra
ACPI: drivers/acpi/pci_link.c: lower printk severity
sony-laptop: Fix event reading in sony-laptop
sony-laptop: Add Vaio FE to the special init sequence
sony-laptop: Make the driver use MSC_SCAN and a setkeycode and getkeycode key table.
sony-laptop: Invoke _INI for SNC devices that provide it
sony-laptop: Add support for recent Vaios Fn keys (C series for now)
sony-laptop: map wireless switch events to KEY_WLAN
sony-laptop: add new SNC handlers
ACPI: thinkpad-acpi: add locking to brightness subdriver
ACPI: thinkpad-acpi: bump up version to 0.15
ACPI: thinkpad-acpi: make EC-based thermal readings non-experimental
ACPI: thinkpad-acpi: make sure DSDT TMPx readings don't return +128
ACPI: thinkpad-acpi: react to Lenovo ThinkPad differences in hot key
ACPI: thinkpad-acpi: allow use of CMOS NVRAM for brightness control
...
Sam Ravnborg [Sun, 22 Jul 2007 09:12:44 +0000 (11:12 +0200)]
x86_64: fix section mismatch warning in init.c
Fix following warning:
WARNING: vmlinux.o(.text+0x188ea): Section mismatch: reference to .init.text:__alloc_bootmem_core (between 'alloc_bootmem_high_node' and 'get_gate_vma')
alloc_bootmem_high_node() is only used from __init scope so declare it __init.
And in addition declare the weak variant __init too.
Sam Ravnborg [Sun, 22 Jul 2007 09:12:42 +0000 (11:12 +0200)]
x86_64: fix section mismatch warning in hpet.c
Fix following warnings:
WARNING: vmlinux.o(.text+0x945e): Section mismatch: reference to .init.text:__set_fixmap (between 'hpet_arch_init' and 'hpet_mask_rtc_irq_bit')
WARNING: vmlinux.o(.text+0x9474): Section mismatch: reference to .init.text:__set_fixmap (between 'hpet_arch_init' and 'hpet_mask_rtc_irq_bit')
hpet_arch_init is only used from __init context so mark it __init.
x86: Replace NSC/Cyrix specific chipset access macros by inlined functions.
Due to index register access ordering problems, when using macros a line
like this fails (and does nothing):
setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
With inlined functions this line will work as expected.
Note about a side effect: Seems on Geode GX1 based systems the
"suspend on halt power saving feature" was never enabled due to this
wrong macro expansion. With inlined functions it will be enabled, but
this will stop the TSC when the CPU runs into a HLT instruction.
Kernel output something like this:
Clocksource tsc unstable (delta = -472746897 ns)
This is the 3rd version of this patch.
- Adding missed arch/i386/kernel/cpu/mtrr/state.c
Thanks to Andres Salomon
- Adding some big fat comments into the new header file
Suggested by Andi Kleen
Keith Owens [Sun, 22 Jul 2007 09:12:36 +0000 (11:12 +0200)]
i386: Do not include other cpus' interrupt 0 in nmi_watchdog
kstat_irqs(0) includes the count of interrupt 0 from all cpus, not just
the current cpu. The updated interrupt 0 on other cpus can stop the
nmi_watchdog from tripping, so only include the current cpu's int 0.
When a machine check or NMI occurs while multiple byte code is patched
the CPU could theoretically see an inconsistent instruction and crash.
Prevent this by temporarily disabling MCEs and returning early in the
NMI handler.
x86: Fix alternatives and kprobes to remap write-protected kernel text
Reenable kprobes and alternative patching when the kernel text is write
protected by DEBUG_RODATA
Add a general utility function to change write protected text. The new
function remaps the code using vmap to write it and takes care of CPU
synchronization. It also does CLFLUSH to make icache recovery faster.
There are some limitations on when the function can be used, see the
comment.
This is a newer version that also changes the paravirt_ops code.
text_poke also supports multi byte patching now.
Contains bug fixes from Zach Amsden and suggestions from Mathieu
Desnoyers.
This patch uses the read and write functions provided at system.h
for control registers instead of writting raw assembly over and
over again in .c files. Functions to manipulate cr2 and cr8 were
provided, as they were lacking.
Also, removed some extra space after closing brackets
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the i386 behave the same way that x86_64 does when a
segfault happens. A line gets printed to the kernel log so that tools
that need to check for failures can behave more uniformly between
debug.show_unhandled_signals sysctl variable to 0 (or by doing echo 0 >
/proc/sys/debug/exception-trace)
Also, all of the lines being printed are now using printk_ratelimit() to
deny the ability of DoS from a local user with a program like the
following:
main()
{
while (1)
if (!fork()) *(int *)0 = 0;
}
This new revision also includes the fix that Andrew did which got rid of
new sysctl that was added to the system in earlier versions of this.
Also, 'show-unhandled-signals' sysctl has been renamed back to the old
'exception-trace' to avoid breakage of people's scripts.
AK: Enabling by default for i386 will be likely controversal, but let's see what happens
AK: Really folks, before complaining just fix your segfaults
AK: I bet this will find a lot of silent issues
Signed-off-by: Masoud Sharbiani <masouds@google.com> Signed-off-by: Andi Kleen <ak@suse.de>
[ Personally, I've found the complaints useful on x86-64, so I'm all for
this. That said, I wonder if we could do it more prettily.. -Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sun, 22 Jul 2007 07:10:35 +0000 (08:10 +0100)]
Fix ppc64 mismerge
Fix a mismerge in commit 8b6f50ef1d5cc86b278eb42bc91630fad455fb10:
"spufs: make signal-notification files readonly for NOSCHED contexts",
where structs got duplicated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Sun, 22 Jul 2007 15:23:02 +0000 (16:23 +0100)]
[ARM] 4524/1: S3C: Move register out of include/asm-arm/arch-s3c2410
Move register and other definitions out of the
include/asm-arm/arch-s3c2410 into the the arch
directories of include/asm-arm/plat-s3c24xx and
include/asm-arm/plat-s3c.
This move is in preperation of the merging of
s3c2400 and s3c6400.
The following git mv commands are needed before
this patch can be applied:
Ben Dooks [Sun, 22 Jul 2007 15:59:44 +0000 (16:59 +0100)]
[ARM] 4521/2: S3C: Reorganise VA mapping headers
Reorganise the definition of the virtual addresses
used into a common header and update the users to
rename S3C2410 items into a more common S3C defined
macros.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 22 Jul 2007 15:18:22 +0000 (16:18 +0100)]
[ARM] 4519/1: S3C: split S3C2400 values out of S3C24XX map.h
Move the S3C2400 values to their own include directory
series in include/asm-arm/arch-s3c2400 as the support
for the S3C2400 is best placed in its own arch directory.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 22 Jul 2007 15:15:44 +0000 (16:15 +0100)]
[ARM] 4517/1: S3C: Fix debug macros for ARM926 output
Check for ARM926 based S3C24XX based devices as these
only have 64 byte FIFOs, and do not have the model
detection refisters in the same place as the ARM920
based CPUs
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 22 Jul 2007 15:12:04 +0000 (16:12 +0100)]
[ARM] 4514/1: S3C: Rename DEBUG_S3C2410_PORT and DEBUG_S3C_UART
Rename DEBUG_S3C2410_PORT to DEBUG_S3C_PORT as well as
DEBUG_S3C2410_UART to DEBUG_S3C_UART as part of the updates
to moving to plat-s3c for S3C base support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 22 Jul 2007 15:09:44 +0000 (16:09 +0100)]
[ARM] 4511/1: S3C: updated LLSERIAL Kconfig defines for CPU support
Update the Kconfig to create configuration options based on which
CPUs are supported for the low level serial code. This means that
the debug macros can be optimised for the type(s) of CPU that are
being used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create the initial arch/arm/plat-s3c directory and start
linking it into the arch/arm build heirarchy ready to
receive the generic parts of the S3C24XX support to be
used when adding S3C6400 devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks [Sun, 22 Jul 2007 15:05:25 +0000 (16:05 +0100)]
[ARM] 4508/1: S3C: Move items to include/asm-arm/plat-s3c
This patch moves items of the s3c24xx support into
a new plat-s3c directory for items that use the
s3c24xx support but are not directly s3c24xx
compatible, such as the s3c2400 and s3c6400.
[ARM] 4461/1: MXC platform and i.MX31ADS core support
This patch adds the foundation pieces for
the Freescale MXC platforms, including
i.MX2 and i.MX3 based systems.
The bare-bones MX31 support in this patch
boots to the rootdev panic with 8250 serial
console configured "console=ttyS0,115200".
It assumes that Redboot is the boot loader.
Signed-off-by: Quinn Jensen <quinn.jensen@freescale.com> Acked-by: Lennert Buytenhek <buytenh@wantstofly.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Al Viro [Thu, 7 Jun 2007 15:13:31 +0000 (11:13 -0400)]
[PATCH] get rid of AVC_PATH postponed treatment
Selinux folks had been complaining about the lack of AVC_PATH
records when audit is disabled. I must admit my stupidity - I assumed
that avc_audit() really couldn't use audit_log_d_path() because of
deadlocks (== could be called with dcache_lock or vfsmount_lock held).
Shouldn't have made that assumption - it never gets called that way.
It _is_ called under spinlocks, but not those.
Since audit_log_d_path() uses ab->gfp_mask for allocations,
kmalloc() in there is not a problem. IOW, the simple fix is sufficient:
let's rip AUDIT_AVC_PATH out and simply generate pathname as part of main
record. It's trivial to do.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: James Morris <jmorris@namei.org>
The sanity check in audit_match_class() is wrong. We are able to audit
2048 syscalls but in audit_match_class() we were accidentally using
sizeof(_u32) instead of number of bits in _u32 when deciding how many
syscalls were valid. On ia64 in particular we were hitting syscall
numbers over the (wrong) limit of 256. Fixing the audit_match_class
check takes care of the problem.
Signed-off-by: Klaus Weidner <klaus@atsec.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Stephen Rothwell [Sat, 21 Jul 2007 14:27:01 +0000 (00:27 +1000)]
[POWERPC] Constify of_platform_driver match_table
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Stephen Rothwell [Sat, 21 Jul 2007 14:23:03 +0000 (00:23 +1000)]
[POWERPC] Constify of_platform_driver name
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Paul Mackerras <paulus@samba.org>
Some HW platforms, such as the new cell blades, requires some MPIC sources
to be left alone by the operating system. This implements support for
a "protected-sources" property in the mpic controller node containing a list
of source numbers to be protected against operating system interference.
For those interested in the gory details, the MPIC on the southbridge of
those blades has some of the processor outputs routed to the cell, and
at least one routed as a GPIO to the service processor. It will be used
in the GA product for routing some of the southbridge error interrupts
to the service processor which implements some of the RAS stuff, such
as checkstopping when fatal errors occurs before they can propagate.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent signal rework broke ARCH=ppc builds with the following
error:
CC arch/powerpc/kernel/signal.o
arch/powerpc/kernel/signal.c: In function Â\91do_signalÂ\92:
arch/powerpc/kernel/signal.c:142: error: implicit declaration of
function Â\91set_dabrÂ\92
make[1]: *** [arch/powerpc/kernel/signal.o] Error 1
This fixes it by including a function prototype in asm-ppc/system.h.
Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Thu, 19 Jul 2007 00:00:20 +0000 (10:00 +1000)]
[POWERPC] Allow exec faults on readable areas on classic 32-bit PowerPC
Classic 32-bit PowerPC CPUs, and the early 64-bit PowerPC CPUs, don't
provide a way to prevent execution from readable pages, that is, the
MMU doesn't distinguish between data reads and instruction reads,
although a different exception is taken for faults in data accesses
and instruction accesses.
Commit 9ba4ace39fdfe22268daca9f28c5df384ae462cf, in the course of
fixing another bug, added a check that meant that a page fault due
to an instruction access would fail if the vma did not have the
VM_EXEC flag set. This gives an inconsistent enforcement on these
CPUs of the no-execute status of the vma (since reading from the page
is sufficient to allow subsequent execution from it), and causes old
versions of ppc32 glibc (2.2 and earlier) to fail, since they rely
on executing the word before the GOT but don't have it marked
executable.
This fixes the problem by allowing execution from readable (or writable)
areas on CPUs which do not provide separate control over data and
instruction reads.
Signed-off-by: Paul Mackerras <paulus@samba.org> Acked-by: Jon Loeliger <jdl@freescale.com>
Michael Neuling [Wed, 18 Jul 2007 21:56:32 +0000 (07:56 +1000)]
[POWERPC] Fix future firmware feature fixups function failure
Move firmware feature initialisation from pSeries_init_early to the
earlier pSeries_probe_hypertas so they are initialised before firmware
feature fixups are applied.
Currently firmware feature sections are only used for iSeries which
initialises the these features much earlier. This is a bug in waiting
on pSeries.
Also adds some whitespace fixups.
Signed-off-by: Michael Neuling <mikey@neuling.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Paul Mackerras <paulus@samba.org>
In some configuration, xmon help string is larger than xmon_printf
buffer. We need not to use printf. This patch adds xmon_puts and
change to use it to show help string.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Paul Mackerras <paulus@samba.org>
projects / linux-2.6 / log