Randy Dunlap [Sun, 25 Jun 2006 12:48:37 +0000 (05:48 -0700)]
[PATCH] wan/sdla section fixes
netdev->set_config can be called at any time, so these references
to __initdata would be a real problem.
However, problem has not been observed AFAIK.
Fix section mismatch warnings:
WARNING: drivers/net/wan/sdla.o - Section mismatch: reference to .init.data: from .text between 'sdla_set_config' (at offset 0x1b8e) and 'sdla_stats'
WARNING: drivers/net/wan/sdla.o - Section mismatch: reference to .init.data: from .text between 'sdla_set_config' (at offset 0x1e76) and 'sdla_stats'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Peter Staubach [Sun, 25 Jun 2006 12:48:36 +0000 (05:48 -0700)]
[PATCH] ftruncate does not always update m/ctime
In the course of trying to track down a bug where a file mtime was not
being updated correctly, it was discovered that the m/ctime updates were
not quite being handled correctly for ftruncate() calls.
Quoth SUSv3:
open(2):
If O_TRUNC is set and the file did previously exist, upon
successful completion, open() shall mark for update the st_ctime
and st_mtime fields of the file.
truncate(2):
Upon successful completion, if the file size is changed, this
function shall mark for update the st_ctime and st_mtime fields
of the file, and the S_ISUID and S_ISGID bits of the file mode
may be cleared.
ftruncate(2):
Upon successful completion, if fildes refers to a regular file,
the ftruncate() function shall mark for update the st_ctime and
st_mtime fields of the file and the S_ISUID and S_ISGID bits of
the file mode may be cleared. If the ftruncate() function is
unsuccessful, the file is unaffected.
The open(O_TRUNC) and truncate cases were being handled correctly, but the
ftruncate case was being handled like the truncate case. The semantics of
truncate and ftruncate don't quite match, so ftruncate needs to be handled
slightly differently.
The attached patch addresses this issue for ftruncate(2).
My thanx to Stephen Tweedie and Trond Myklebust for their help in
understanding the situation and semantics.
Signed-off-by: Peter Staubach <staubach@redhat.com> Cc: "Stephen C. Tweedie" <sct@redhat.com> Cc: Trond Myklebust <trond.myklebust@fys.uio.no> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
akpm@osdl.org [Sun, 25 Jun 2006 12:48:35 +0000 (05:48 -0700)]
[PATCH] N32 sigset and __COMPAT_ENDIAN_SWAP__
I'm testing glibc on MIPS64, little-endian, N32, O32 and N64 multilibs.
Among the NPTL test failures seen are some arising from sigsuspend problems
for N32: it blocks the wrong signals, so SIGCANCEL (SIGRTMIN) is blocked
despite glibc's carefully excluding it from sets of signals to block.
Specifically, testing suggests it blocks signal N^32 instead of signal N,
so (in the example tested) blocking SIGUSR1 (17) blocks signal 49 instead.
glibc's sigset_t uses an array of unsigned long, as does the kernel.
In both cases, signal N+1 is represented as
(1UL << (N % (8 * sizeof (unsigned long)))) in word number
(N / (8 * sizeof (unsigned long))).
Thus the N32 glibc uses an array of 32-bit words and the N64 kernel uses an
array of 64-bit words. For little-endian, the layout is the same, with
signals 1-32 in the first 4 bytes, signals 33-64 in the second, etc.; for
big-endian, userspace has that layout while in the kernel each 8 bytes have
the two halves swapped from the userspace layout.
The N32 sigsuspend syscall uses sigset_from_compat to convert the userspace
sigset to kernel format. If __COMPAT_ENDIAN_SWAP__ is *not* set, this uses
logic of the form
to convert the userspace sigset to a kernel one. This looks correct to me
for both big and little endian, given that in userspace compat->sig[1] will
represent signals 33-64, and so will the high 32 bits of set->sig[0] in the
kernel. If however __COMPAT_ENDIAN_SWAP__ *is* set, as it is for
__MIPSEL__, it uses
which seems incorrect for both big and little endian, and would
explain the observed symptoms.
This code is the only use of __COMPAT_ENDIAN_SWAP__, so if incorrect
then that macro serves no purpose, in which case something like the
following patch would seem appropriate to remove it.
Signed-off-by: Joseph Myers <joseph@codesourcery.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Randy Dunlap [Sun, 25 Jun 2006 12:48:29 +0000 (05:48 -0700)]
[PATCH] checkstack: print module names
Finding "init_module" high stack usage problems is challenging when there
are over 1600 "init_module" functions in the kernel tree, so make
checkstack.pl print out the filename where the stack usage occurs. This is
useful for code built as loadable modules.
For built-in code, it just prints the kernel image file name, like
"vmlinux". Examples:
Andrew Morton [Sun, 25 Jun 2006 12:48:27 +0000 (05:48 -0700)]
[PATCH] at91rm9200-rtc-driver-tidy
- whitespace fixes (80-col display)
- one unneeded cast of void*
Cc: Andrew Victor <andrew@sanpeople.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Victor [Sun, 25 Jun 2006 12:48:27 +0000 (05:48 -0700)]
[PATCH] AT91RM9200 RTC driver
Adds support for the RTC integrated in the Atmel AT91RM9200 SoC.
Driver was originally written for 2.4 by Rick Bronson. Then converted to
2.6 ARM RTC API by Steven Scholz. Now converted to the RTC class model.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Victor [Sun, 25 Jun 2006 12:48:25 +0000 (05:48 -0700)]
[PATCH] RTC: Add rtc_year_days() to calculate tm_yday
RTC: Add exported function rtc_year_days() to calculate the tm_yday value.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Raphael Assenat [Sun, 25 Jun 2006 12:48:24 +0000 (05:48 -0700)]
[PATCH] Add v3020 RTC support
This patch adds support for the v3020 RTC from EM Microelectronic.
The v3020 RTC is designed to be connected on a bus using only one data bit.
Since any data bit may be used, it is necessary to specify this to the
driver by passing a struct v3020_platform_data pointer (see
include/linux/rtc-v3020.h) to the driver.
Part of the following code comes from the kernel patchs produced by
Compulab for their products. The original file (available here:
http://raph.people.8d.com/misc/emv3020.c) was released under the terms of
the GPL license.
Raphael Assenat [Sun, 25 Jun 2006 12:48:23 +0000 (05:48 -0700)]
[PATCH] Add max6902 RTC support
Add support for the MAX6902 SPI RTC chip. Tested on a pxa2xx cpu.
The compulab code comes from the kernel patch the produce for their
cn-x255 board. (inside a zip file on the
http://www.compulab.co.il/x255/html/x255-developer.htm)
The original file (drivers/char/max6902.c) was GPL, which is of course
an appropriate licence:
/*
* max6902.c
*
* Driver for MAX6902 RTC
*
* Copyright (C) 2004 Compulab Ltd.
*
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
*
*/
For reference, you can get the original file here:
http://raph.people.8d.com/misc/max6902.c
G. Liakhovetski [Sun, 25 Jun 2006 12:48:18 +0000 (05:48 -0700)]
[PATCH] drivers/acorn/char/pcf8583.[hc] vs. RTC subsystem
A port of the driver for the pcf8583 i2c rtc controller to the generic RTC
framework by Alessandro Zummo. Based on
drivers/acorn/char/{pcf8583.[hc],i2c.c}. Hopefully, acorn can be converted
too to use this driver in the future.
Signed-off-by: G. Liakhovetski <gl@dsa-ac.de> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Cc: Russell King <rmk@arm.linux.org.uk> Cc: Jean Delvare <khali@linux-fr.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Atsushi Nemoto [Sun, 25 Jun 2006 12:48:17 +0000 (05:48 -0700)]
[PATCH] RTC: rtc-dev UIE emulation
Import genrtc's RTC UIE emulation (CONFIG_GEN_RTC_X) to rtc-dev driver with
slight adjustments/refinements. This makes UIE-less rtc drivers work
better with programs doing read/poll on /dev/rtc, such as hwclock. This
emulation should not harm rtc drivers with UIE support, since
rtc_dev_ioctl() calls underlaying rtc driver's ioctl() first.
David Brownell [Sun, 25 Jun 2006 12:48:17 +0000 (05:48 -0700)]
[PATCH] "RTC-framework" driver for DS1307 and similar RTC chips
This is an "RTC-framework" driver for DS1307 and similar RTC chips,
It should be a full replacement for the existing ds1337.c driver (using the
older RTC glue), giving a net increase in the number of RTC chips that work
out-of-the-box. There's a whole cluster of RTCs that are very similar, but
the 1337 driver was a bit too picky to work with most of them.
Still no support for RTC alarm IRQs (on chips that support them).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: James Chapman <jchapman@katalix.com> Signed-off-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jesper Juhl [Sun, 25 Jun 2006 12:48:16 +0000 (05:48 -0700)]
[PATCH] Correct sa'K' description in sysrq.txt
sysrq SAK is described as being something you should mistake for SAK from
c2 compliant systems - whoops. What's meant is that it should *not* be
mistaken as such.
Jan Engelhardt [Sun, 25 Jun 2006 12:48:15 +0000 (05:48 -0700)]
[PATCH] printk time parameter
Currently, enabling/disabling printk timestamps is only possible through
reboot (bootparam) or recompile. I normally do not run with timestamps
(since syslog handles that in a good manner), but for measuring small
kernel delays (e.g. irq probing - see parport thread) I needed subsecond
precision, but then again, just for some minutes rather than all kernel
messages to come. The following patch adds a module_param() with which the
timestamps can be en-/disabled in a live system through
/sys/modules/printk/parameters/printk_time.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Davide Libenzi [Sun, 25 Jun 2006 12:48:14 +0000 (05:48 -0700)]
[PATCH] epoll: use unlocked wqueue operations
A few days ago Arjan signaled a lockdep red flag on epoll locks, and
precisely between the epoll's device structure lock (->lock) and the wait
queue head lock (->lock).
Like I explained in another email, and directly to Arjan, this can't happen
in reality because of the explicit check at eventpoll.c:592, that does not
allow to drop an epoll fd inside the same epoll fd. Since lockdep is
working on per-structure locks, it will never be able to know of policies
enforced in other parts of the code.
It was decided time ago of having the ability to drop epoll fds inside
other epoll fds, that triggers a very trick wakeup operations (due to
possibly reentrant callback-driven wakeups) handled by the
ep_poll_safewake() function. While looking again at the code though, I
noticed that all the operations done on the epoll's main structure wait
queue head (->wq) are already protected by the epoll lock (->lock), so that
locked-style functions can be used to manipulate the ->wq member. This
makes both a lock-acquire save, and lockdep happy.
Running totalmess on my dual opteron for a while did not reveal any problem
so far:
http://www.xmailserver.org/totalmess.c
Signed-off-by: Davide Libenzi <davidel@xmailserver.org> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Valerie Henson [Sun, 25 Jun 2006 12:48:12 +0000 (05:48 -0700)]
[PATCH] Make EXT2_DEBUG work again
This patch makes EXT2_DEBUG work again. Due to lack of proper include
file, EXT2_DEBUG was undefined in bitmap.c and ext2_count_free() is left
out. Moved to balloc.c and removed bitmap.c entirely.
Second, debug versions of ext2_count_free_{inodes/blocks} reacquires
superblock lock. Moved lock into callers.
Signed-off-by: Val Henson <val_henson@linux.intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
H. Peter Anvin [Sun, 25 Jun 2006 12:48:10 +0000 (05:48 -0700)]
[PATCH] Make sysctl obligatory except under CONFIG_EMBEDDED
Make makes sysctl non-optional unless EMBEDDED is set. There are a number
of interfaces exposed via sysctl, enough that it has to be considered core
kernel functionality at this point.
Signed-off-by: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mingming Cao [Sun, 25 Jun 2006 12:48:07 +0000 (05:48 -0700)]
[PATCH] ext3_fsblk_t: the rest of in-kernel filesystem blocks conversion
Convert the ext3 in-kernel filesystem blocks to ext3_fsblk_t. Convert the
rest of all unsigned long type in-kernel filesystem blocks to ext3_fsblk_t,
and replace the printk format string respondingly.
Signed-off-by: Mingming Cao <cmm@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mingming Cao [Sun, 25 Jun 2006 12:48:06 +0000 (05:48 -0700)]
[PATCH] ext3_fsblk_t: filesystem, group blocks and bug fixes
Some of the in-kernel ext3 block variable type are treated as signed 4 bytes
int type, thus limited ext3 filesystem to 8TB (4kblock size based). While
trying to fix them, it seems quite confusing in the ext3 code where some
blocks are filesystem-wide blocks, some are group relative offsets that need
to be signed value (as -1 has special meaning). So it seem saner to define
two types of physical blocks: one is filesystem wide blocks, another is
group-relative blocks. The following patches clarify these two types of
blocks in the ext3 code, and fix the type bugs which limit current 32 bit ext3
filesystem limit to 8TB.
With this series of patches and the percpu counter data type changes in the mm
tree, we are able to extend exts filesystem limit to 16TB.
This work is also a pre-request for the recent >32 bit ext3 work, and makes
the kernel to able to address 48 bit ext3 block a lot easier: Simply redefine
ext3_fsblk_t from unsigned long to sector_t and redefine the format string for
ext3 filesystem block corresponding.
Two RFC with a series patches have been posted to ext2-devel list and have
been reviewed and discussed:
http://marc.theaimsgroup.com/?l=ext2-devel&m=114722190816690&w=2
Patches are tested on both 32 bit machine and 64 bit machine, <8TB ext3 and
>8TB ext3 filesystem(with the latest to be released e2fsprogs-1.39). Tests
includes overnight fsx, tiobench, dbench and fsstress.
This patch:
Defines ext3_fsblk_t and ext3_grpblk_t, and the printk format string for
filesystem wide blocks.
This patch classifies all block group relative blocks, and ext3_fsblk_t blocks
occurs in the same function where used to be confusing before. Also include
kernel bug fixes for filesystem wide in-kernel block variables. There are
some fileystem wide blocks are treated as int/unsigned int type in the kernel
currently, especially in ext3 block allocation and reservation code. This
patch fixed those bugs by converting those variables to ext3_fsblk_t(unsigned
long) type.
Signed-off-by: Mingming Cao <cmm@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix section warning:
WARNING: drivers/scsi/megaraid/megaraid_mbox.o - Section mismatch: reference to .init.text: from .text between 'megaraid_probe_one' (at offset 0x171e) and 'megaraid_queue_command'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Sun, 25 Jun 2006 12:48:02 +0000 (05:48 -0700)]
[PATCH] Make copy_from_user_inatomic NOT zero the tail on i386
As described in a previous patch and documented in mm/filemap.h,
copy_from_user_inatomic* shouldn't zero out the tail of the buffer after an
incomplete copy.
This patch implements that change for i386.
For the _nocache version, a new __copy_user_intel_nocache is defined similar
to copy_user_zeroio_intel_nocache, and this is ultimately used for the copy.
For the regular version, __copy_from_user_ll_nozero is defined which uses
__copy_user and __copy_user_intel - the later needs casts to reposition the
__user annotations.
If copy_from_user_atomic is given a constant length of 1, 2, or 4, then we do
still zero the destintion on failure. This didn't seem worth the effort of
fixing as the places where it is used really don't care.
Signed-off-by: Neil Brown <neilb@suse.de> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
NeilBrown [Sun, 25 Jun 2006 12:47:58 +0000 (05:47 -0700)]
[PATCH] Prepare for __copy_from_user_inatomic to not zero missed bytes
The problem is that when we write to a file, the copy from userspace to
pagecache is first done with preemption disabled, so if the source address is
not immediately available the copy fails *and* *zeros* *the* *destination*.
This is a problem because a concurrent read (which admittedly is an odd thing
to do) might see zeros rather that was there before the write, or what was
there after, or some mixture of the two (any of these being a reasonable thing
to see).
If the copy did fail, it will immediately be retried with preemption
re-enabled so any transient problem with accessing the source won't cause an
error.
The first copying does not need to zero any uncopied bytes, and doing so
causes the problem. It uses copy_from_user_atomic rather than copy_from_user
so the simple expedient is to change copy_from_user_atomic to *not* zero out
bytes on failure.
The first of these two patches prepares for the change by fixing two places
which assume copy_from_user_atomic does zero the tail. The two usages are
very similar pieces of code which copy from a userspace iovec into one or more
page-cache pages. These are changed to remove the assumption.
The second patch changes __copy_from_user_inatomic* to not zero the tail.
Once these are accepted, I will look at similar patches of other architectures
where this is important (ppc, mips and sparc being the ones I can find).
This patch:
There is a problem with __copy_from_user_inatomic zeroing the tail of the
buffer in the case of an error. As it is called in atomic context, the error
may be transient, so it results in zeros being written where maybe they
shouldn't be.
In the usage in filemap, this opens a window for a well timed read to see data
(zeros) which is not consistent with any ordering of reads and writes.
Most cases where __copy_from_user_inatomic is called, a failure results in
__copy_from_user being called immediately. As long as the latter zeros the
tail, the former doesn't need to. However in *copy_from_user_iovec
implementations (in both filemap and ntfs/file), it is assumed that
copy_from_user_inatomic will zero the tail.
This patch removes that assumption, so that after this patch it will
be safe for copy_from_user_inatomic to not zero the tail.
This patch also adds some commentary to filemap.h and asm-i386/uaccess.h.
After this patch, all architectures that might disable preempt when
kmap_atomic is called need to have their __copy_from_user_inatomic* "fixed".
This includes
- powerpc
- i386
- mips
- sparc
Signed-off-by: Neil Brown <neilb@suse.de> Cc: David Howells <dhowells@redhat.com> Cc: Anton Altaparmakov <aia21@cantab.net> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: William Lee Irwin III <wli@holomorphy.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chris Wright [Sun, 25 Jun 2006 12:47:55 +0000 (05:47 -0700)]
[PATCH] cpuset: remove extra cpuset_zone_allowed check in __alloc_pages
This is redundant with check in wakeup_kswapd.
Signed-off-by: Chris Wright <chrisw@sous-sol.org> Acked-by: Paul Jackson <pj@sgi.com> Acked-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mingming Cao [Sun, 25 Jun 2006 12:47:50 +0000 (05:47 -0700)]
[PATCH] Avoid disk sector_t overflow for >2TB ext3 filesystem
If ext3 filesystem is larger than 2TB, and sector_t is a u32 (i.e.
CONFIG_LBD not defined in the kernel), the calculation of the disk sector
will overflow. Add check at ext3_fill_super() and ext3_group_extend() to
prevent mount/remount/resize >2TB ext3 filesystem if sector_t size is 4
bytes.
Verified this patch on a 32 bit platform without CONFIG_LBD defined
(sector_t is 32 bits long), mount refuse to mount a 10TB ext3.
Signed-off-by: Mingming Cao<cmm@us.ibm.com> Acked-by: Andreas Dilger <adilger@clusterfs.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
schedule_on_each_cpu() presently does a large kmalloc - 96 kbytes on 1024 CPU
64-bit.
Rework it so that we do one 8192-byte allocation and then a pile of tiny ones,
via alloc_percpu(). This has a much higher chance of success (100% in the
current VM).
This also has the effect of reducing the memory requirements from NR_CPUS*n to
num_possible_cpus()*n.
Cc: Christoph Lameter <clameter@engr.sgi.com> Cc: Andi Kleen <ak@muc.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Randy Dunlap [Sun, 25 Jun 2006 12:47:47 +0000 (05:47 -0700)]
[PATCH] kernel-doc: drop leading space in sections
Drop leading space of kernel-doc section contents.
"Section" data (contents) are split from the section header
(e.g., Note: below is a section header:
* Note: list_empty on entry does not return true after this, the entry is
* in an undefined state.
).
Currently the data/contents begins with a space and is left that way, which
causes it to look bad when printed (in text mode; see example below), so
just remove the leading space.
Note:
list_empty on entry does not return true after this, the entry is in an
undefined state.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Sun, 25 Jun 2006 12:47:46 +0000 (05:47 -0700)]
[PATCH] pdflush: handle resume wakeups
pdflush is carefully designed to ensure that all wakeups have some
corresponding work to do - if a woken-up pdflush thread discovers that it
hasn't been given any work to do then this is considered an error.
That all broke when swsusp came along - because a timer-delivered wakeup to a
frozen pdflush thread will just get lost. This causes the pdflush thread to
get lost as well: the writeback timer is supposed to be re-armed by pdflush in
process context, but pdflush doesn't execute the callout which does this.
Fix that up by ignoring the return value from try_to_freeze(): jsut proceed,
see if we have any work pending and only go back to sleep if that is not the
case.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Sun, 25 Jun 2006 12:47:45 +0000 (05:47 -0700)]
[PATCH] cpqarray section fix
WARNING: drivers/block/cpqarray.o - Section mismatch: reference to .init.text: from .text between 'cpqarray_register_ctlr' (at offset 0xe98) and 'alloc_cpqarray_hba'
WARNING: drivers/block/cpqarray.o - Section mismatch: reference to .init.text: from .text between 'cpqarray_register_ctlr' (at offset 0xe9c) and 'alloc_cpqarray_hba'
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alan Cox [Sun, 25 Jun 2006 12:47:44 +0000 (05:47 -0700)]
[PATCH] IDE CD end-of media error fix
This is a patch from Alan that fixes a real ide-cd.c regression causing
bogus "Media Check" failures for perfectly valid Fedora install ISOs, on
certain CD-ROM drives.
This is a forward port to 2.6.16 (from RHEL) of the minimal changes for the
end of media problem. It may not be sufficient for some controllers
(promise notably) and it does not touch the locking so the error path
locking is as horked as in mainstream.
From: Ingo Molnar <mingo@elte.hu>
I have ported the patch to 2.6.17-rc4 and tested it by provoking
end-of-media IO errors with an unaligned ISO image. Unlike the vanilla
kernel, the patched kernel interpreted the error condition correctly with
512 byte granularity:
Adrian Bunk [Sun, 25 Jun 2006 12:47:41 +0000 (05:47 -0700)]
[PATCH] kernel/sys.c: cleanups
- proper prototypes for the following functions:
- ctrl_alt_del() (in include/linux/reboot.h)
- getrusage() (in include/linux/resource.h)
- make the following needlessly global functions static:
- kernel_restart_prepare()
- kernel_kexec()
[akpm@osdl.org: compile fix] Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michael Ellerman [Sun, 25 Jun 2006 12:47:40 +0000 (05:47 -0700)]
[PATCH] Make printk work for really early debugging
Currently printk is no use for early debugging because it refuses to
actually print anything to the console unless
cpu_online(smp_processor_id()) is true.
The stated explanation is that console drivers may require per-cpu
resources, or otherwise barf, because the system is not yet setup
correctly. Fair enough.
However some console drivers might be quite happy running early during
boot, in fact we have one, and so it'd be nice if printk understood that.
So I added a flag (which I would have called CON_BOOT, but that's taken)
called CON_ANYTIME, which indicates that a console is happy to be called
anytime, even if the cpu is not yet online.
Tested on a Power 5 machine, with both a CON_ANYTIME driver and a bogus
console driver that BUG()s if called while offline. No problems AFAICT.
Built for i386 UP & SMP.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Daniel Walker [Sun, 25 Jun 2006 12:47:37 +0000 (05:47 -0700)]
[PATCH] idetape gcc 4.1 warning fix
In both the read and write cases it will return an error if
copy_{from/to}_user faults. However, I let the driver try to read/write as
much as it can just as it normally would , then finally it returns an error
if there was one. This was the most straight forward way to handle the
error , since there isn't a clear way to clean up the buffers on error .
I moved retval in idetape_chrdev_write() down into the actual code blocks
since it's really once used there, and it conflicted with my ret variable.
Fixes the following warning,
drivers/ide/ide-tape.c: In function â\80\98idetape_copy_stage_from_userâ\80\99:
drivers/ide/ide-tape.c:2662: warning: ignoring return value of â\80\98copy_from_userâ\80\99, declared with attribute warn_unused_result
drivers/ide/ide-tape.c: In function â\80\98idetape_copy_stage_to_userâ\80\99:
drivers/ide/ide-tape.c:2689: warning: ignoring return value of â\80\98copy_to_userâ\80\99, declared with attribute warn_unused_result
Signed-off-by: Daniel Walker <dwalker@mvista.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan Engelhardt [Sun, 25 Jun 2006 12:47:36 +0000 (05:47 -0700)]
[PATCH] openpromfs: factorize out
"Move" "common code" out to PTR_NOD, which does the conversion from private
pointer to node number. This is to reduce potential casting/conversion errors
due to redundancy. (The naming PTR_NOD follows PTR_ERR, turning a pointer
into xyz.)
[akpm@osdl.org: cleanups] Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan Engelhardt [Sun, 25 Jun 2006 12:47:35 +0000 (05:47 -0700)]
[PATCH] openpromfs: fix missing NUL
tchars is not '\0'-terminated so the strtoul may run into problems. Fix that.
Also make tchars as big as a long in hexadecimal form would take rather than
just 16.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] oprofile: convert from semaphores to mutexes
Signed-off-by: Markus Armbruster <armbru@redhat.com> Cc: Philippe Elie <phil.el@wanadoo.fr> Cc: John Levon <levon@movementarian.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andrew Morton [Sun, 25 Jun 2006 12:47:32 +0000 (05:47 -0700)]
[PATCH] msnd section fix
WARNING: sound/oss/msnd.o - Section mismatch: reference to .init.text:msnd_register from __ksymtab between '__ksymtab_msnd_register' (at offset 0x0) and '__ksymtab_msnd_unregister'
This symbol is exported. It'll oops if the driver is nonmodular and the
caller is modular.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In ufs code there is function: ubh_ll_rw_block, it has parameter how many
ufs_buffer_head it should handle, but it always called with "1" on the place
of this parameter. This patch removes unused parameter of "ubh_ll_wr_block".
ufs super block contains some statistic about file systems, like amount of
directories, free blocks, inodes and so on.
UFS1 hold this information in one location and uses 32bit integers for such
information, UFS2 hold statistic in another location and uses 64bit integers.
There is transition variant, if UFS1 has type 44BSD and flags field in super
block has some special value this mean that we work with statistic like UFS2
does. and this also means that nobody care about old(UFS1) statistic.
So if start fsck against such file system, after usage linux ufs driver, it
found error: at now only UFS1 like statistic is updated.
This patch should fix this. Also it contains some minor cleanup: CodingSytle
and remove unused variables.
Andrew Morton [Sun, 25 Jun 2006 12:47:28 +0000 (05:47 -0700)]
[PATCH] ufs: printk warning fixes
fs/ufs/super.c: In function `ufs_print_super_stuff':
fs/ufs/super.c:103: warning: unsigned int format, different type arg (arg 2) fs/ufs/super.c: In function `ufs2_print_super_stuff': fs/ufs/super.c:147: warning: unsigned int format, different type arg (arg 2) fs/ufs/super.c: In function `ufs_print_cylinder_stuff':
fs/ufs/super.c:175: warning: unsigned int format, different type arg (arg 2)
Presently if we allocate several "metadata" blocks (pointers to indirect
blocks for example), we fill with zeroes only the first block. This cause
some problems in "truncate" function. Also this patch remove some unused
arguments from several functions and add comments.
Currently to turn on debug mode "user" has to edit ~10 files, to turn off he
has to do it again.
This patch introduce such changes:
1)turn on(off) debug messages via ".config"
2)remove unnecessary duplication of code
3)make "UFSD" macros more similar to function
4)fix some compiler warnings
[PATCH] ufs: not usual amounts of fragments per block
The writing to UFS file system with block/fragment!=8 may cause bogus
behaviour. The problem in "ufs_bitmap_search" function, which doesn't work
correctly in "block/fragment!=8" case. The idea is stolen from BSD code.
There are two ugly macros in ufs code:
#define UCPI_UBH ((struct ufs_buffer_head *)ucpi)
#define USPI_UBH ((struct ufs_buffer_head *)uspi)
when uspi looks like
struct {
struct ufs_buffer_head ;
}
and USPI_UBH has some sence,
ucpi looks like
struct {
struct not_ufs_buffer_head;
}
To prevent bugs in future, this patch convert macros to inline function and
fix "ucpi" structure.
First of all some necessary notes about UFS by it self: To avoid waste of disk
space the tail of file consists not from blocks (which is ordinary big enough,
16K usually), it consists from fragments(which is ordinary 2K). When file is
growing its tail occupy 1 fragment, 2 fragments... At some stage decision to
allocate whole block is made and all fragments are moved to one block.
bh = sb_bread
bh->b_blocknr = result + i;
mark_buffer_dirty (bh);
This is wrong solution, because:
- it didn't take into consideration that there is another cache: "inode page
cache"
- because of sb_getblk uses not b_blocknr, (it uses page->index) to find
certain block, this breaks sb_getblk.
How this situation is handled now: we go though all "page inode cache", if
there are no such page in cache we load it into cache, and change b_blocknr.
Currently, ufs write support have two sets of problems: work with files and
work with directories.
This series of patches should solve the first problem.
This patch is similar to http://lkml.org/lkml/2006/1/17/61 this patch
complements it.
The situation the same: in ufs_trunc_(not direct), we read block, check if
count of links to it is equal to one, if so we finish cycle, if not
continue. Because of "count of links" always >=2 this operation cause
infinite cycle and hang up the kernel.
Alan Stern [Sun, 25 Jun 2006 12:47:15 +0000 (05:47 -0700)]
[PATCH] Allow raw_notifier callouts to unregister themselves
Since raw_notifier chains don't benefit from any centralized locking
protections, they shouldn't suffer from the associated limitations. Under
some circumstances it might make sense for a raw_notifier callout routine
to unregister itself from the notifier chain. This patch (as678) changes
the notifier core to allow for such things.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Paul Mackerras [Sun, 25 Jun 2006 12:47:14 +0000 (05:47 -0700)]
[PATCH] Define __raw_get_cpu_var and use it
There are several instances of per_cpu(foo, raw_smp_processor_id()), which
is semantically equivalent to __get_cpu_var(foo) but without the warning
that smp_processor_id() can give if CONFIG_DEBUG_PREEMPT is enabled. For
those architectures with optimized per-cpu implementations, namely ia64,
powerpc, s390, sparc64 and x86_64, per_cpu() turns into more and slower
code than __get_cpu_var(), so it would be preferable to use __get_cpu_var
on those platforms.
This defines a __raw_get_cpu_var(x) macro which turns into per_cpu(x,
raw_smp_processor_id()) on architectures that use the generic per-cpu
implementation, and turns into __get_cpu_var(x) on the architectures that
have an optimized per-cpu implementation.
Signed-off-by: Paul Mackerras <paulus@samba.org> Acked-by: David S. Miller <davem@davemloft.net> Acked-by: Ingo Molnar <mingo@elte.hu> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6 / log