For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
Now the skb->nh union has just one member, .raw, i.e. it is just like the
skb->mac union, strange, no? I'm just leaving it like that till the transport
layer is done with, when we'll rename skb->mac.raw to skb->mac_header (or
->mac_header_offset?), ditto for ->{h,nh}.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Show what protocols are bound to what packet types in /proc/net/ptype
Uses kallsyms to decode function pointers if possible.
Example:
Type Device Function
ALL eth1 packet_rcv_spkt+0x0
0800 ip_rcv+0x0
0806 arp_rcv+0x0
86dd :ipv6:ipv6_rcv+0x0
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the network header, it is still legal
to touch skb->nh.raw directly if just adding to, subtracting from or setting it
to another layer header.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[SK_BUFF]: Use skb_reset_network_header where the skb_pull return was being used
But only in the cases where its a newly allocated skb, i.e. one where skb->tail
is equal to skb->data, or just after skb_reserve, where this requirement is
maintained.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->nh.raw = skb->data' operation, so that we can
later turn skb->nh.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency with all the other skb->nh.raw accessors.
Also do some really obvious simplifications in pppoe_recvmsg, well the
kfree_skb one is not so obvious, but free() and kfree() have the same behaviour
(hint :-) ).
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For the places where we need a pointer to the mac header, it is still legal to
touch skb->mac.raw directly if just adding to, subtracting from or setting it
to another layer header.
This one also converts some more cases to skb_reset_mac_header() that my
regex missed as it had no spaces before nor after '=', ugh.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->mac.raw = skb->data' operation, so that we can
later turn skb->mac.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 26 Mar 2007 05:14:49 +0000 (22:14 -0700)]
[NET]: Adding SO_TIMESTAMPNS / SCM_TIMESTAMPNS support
Now that network timestamps use ktime_t infrastructure, we can add a new
SOL_SOCKET sockopt SO_TIMESTAMPNS.
This command is similar to SO_TIMESTAMP, but permits transmission of
a 'timespec struct' instead of a 'timeval struct' control message.
(nanosecond resolution instead of microsecond)
Control message is labelled SCM_TIMESTAMPNS instead of SCM_TIMESTAMP
A socket cannot mix SO_TIMESTAMP and SO_TIMESTAMPNS : the two modes are
mutually exclusive.
sock_recv_timestamp() became too big to be fully inlined so I added a
__sock_recv_timestamp() helper function.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> CC: linux-arch@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
Covert network warning messages from a compile time to runtime choice.
Removes kernel config option and replaces it with new /proc/sys/net/core/warnings.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 19 Mar 2007 00:33:16 +0000 (17:33 -0700)]
[NET]: Introduce SIOCGSTAMPNS ioctl to get timestamps with nanosec resolution
Now network timestamps use ktime_t infrastructure, we can add a new
ioctl() SIOCGSTAMPNS command to get timestamps in 'struct timespec'.
User programs can thus access to nanosecond resolution.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> CC: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Adrian Bunk [Thu, 8 Mar 2007 03:33:52 +0000 (19:33 -0800)]
[TCP/DCCP/RANDOM]: Remove unused exports.
This patch removes the following not or no longer used exports:
- drivers/char/random.c: secure_tcp_sequence_number
- net/dccp/options.c: sysctl_dccp_feat_sequence_window
- net/netlink/af_netlink.c: netlink_set_err
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 26 Mar 2007 03:10:56 +0000 (20:10 -0700)]
[UDP]: Clean up UDP-Lite receive checksum
This patch eliminates some duplicate code for the verification of
receive checksums between UDP-Lite and UDP. It does this by
introducing __skb_checksum_complete_head which is identical to
__skb_checksum_complete_head apart from the fact that it takes
a length parameter rather than computing the first skb->len bytes.
As a result UDP-Lite will be able to use hardware checksum offload
for packets which do not use partial coverage checksums. It also
means that UDP-Lite loopback no longer does unnecessary checksum
verification.
If any NICs start support UDP-Lite this would also start working
automatically.
This patch removes the assumption that msg_flags has MSG_TRUNC clear
upon entry in recvmsg.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 7 Mar 2007 04:23:10 +0000 (20:23 -0800)]
[IPV4]: Optimize inet_getpeer()
1) Some sysctl vars are declared __read_mostly
2) We can avoid updating stack[] when doing an AVL lookup only.
lookup() macro is extended to receive a second parameter, that may be NULL
in case of a pure lookup (no need to save the AVL path). This removes
unnecessary instructions, because compiler knows if this _stack parameter is
NULL or not.
text size of net/ipv4/inetpeer.o is 2063 bytes instead of 2107 on x86_64
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
The Newton-Raphson method is quadratically convergent so
only a small fixed number of steps are necessary.
Therefore it is faster to unroll the loop. Since div64_64 is no longer
inline it won't cause code explosion.
Also fixes a bug that can occur if x^2 was bigger than 32 bits.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Nominally an autoconfigured IPv6 address is added to an interface in the
Tentative state (as per RFC 2462). Addresses in this state remain in this
state while the Duplicate Address Detection process operates on them to
determine their uniqueness on the network. During this period, these
tentative addresses may not be used for communication, increasing the time
before a node may be able to communicate on a network. Using Optimistic
Duplicate Address Detection, autoconfigured addresses may be used
immediately for communication on the network, as long as certain rules are
followed to avoid conflicts with other nodes during the Duplicate Address
Detection process.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yasuyuki Kozakai [Thu, 30 Nov 2006 05:43:28 +0000 (14:43 +0900)]
[IPV6] IP6TUNNEL: Enable to control the handled inner protocol.
ip6_tunnel before supporting IPv4/IPv6 tunnel allows only IPPROTO_IPV6
in configurations from userland. This allows userland to set IPPROTO_IPIP
and 0(wildcard). ip6_tunnel only handles allowed inner protocols.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV6] IP6TUNNEL: Rename functions ip6ip6_* to ip6_tnl_*.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yasuyuki Kozakai [Wed, 14 Feb 2007 15:43:16 +0000 (00:43 +0900)]
[IPV6] IP6TUNNEL: Add support to IPv4 over IPv6 tunnel.
Some notes
- Protocol number IPPROTO_IPIP is used for IPv4 over IPv6 packets.
- If IP6_TNL_F_USE_ORIG_TCLASS is set, TOS in IPv4 header is copied to
Traffic Class in outer IPv6 header on xmit.
- IP6_TNL_F_USE_ORIG_FLOWLABEL is ignored on xmit of IPv4 packets, because
IPv4 header does not have flow label.
- Kernel sends ICMP error if IPv4 packet is too big on xmit, even if
DF flag is not set.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV6] IP6TUNNEL: Split out generic routine in ip6ip6_xmit().
This enables to add IPv4/IPv6 specific handling later,
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV6] IP6TUNNEL: Split out generic routine in ip6ip6_rcv().
This enables to add IPv4/IPv6 specific handling later,
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yasuyuki Kozakai [Tue, 31 Oct 2006 14:11:25 +0000 (23:11 +0900)]
[IPV6] IP6TUNNEL: Split out generic routine in ip6ip6_err().
This enables to add IPv4/IPv6 specific error handling later,
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Thu, 19 Apr 2007 23:16:32 +0000 (16:16 -0700)]
[NET]: convert network timestamps to ktime_t
We currently use a special structure (struct skb_timeval) and plain
'struct timeval' to store packet timestamps in sk_buffs and struct
sock.
This has some drawbacks :
- Fixed resolution of micro second.
- Waste of space on 64bit platforms where sizeof(struct timeval)=16
I suggest using ktime_t that is a nice abstraction of high resolution
time services, currently capable of nanosecond resolution.
As sizeof(ktime_t) is 8 bytes, using ktime_t in 'struct sock' permits
a 8 byte shrink of this structure on 64bit architectures. Some other
structures also benefit from this size reduction (struct ipq in
ipv4/ip_fragment.c, struct frag_queue in ipv6/reassembly.c, ...)
Once this ktime infrastructure adopted, we can more easily provide
nanosecond resolution on top of it. (ioctl SIOCGSTAMPNS and/or
SO_TIMESTAMPNS/SCM_TIMESTAMPNS)
Note : this patch includes a bug correction in
compat_sock_get_timestamp() where a "err = 0;" was missing (so this
syscall returned -ENOENT instead of 0)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> CC: Stephen Hemminger <shemminger@linux-foundation.org> CC: John find <linux.kernel@free.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Since devices can change name and other wierdness, don't hold onto
a copy of device name, instead use pointer to output device.
Fix a couple of leaks in error handling path as well.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
The existing htonl() macro is smart enough to do the same code as
using __constant_htonl() and it looks cleaner.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Remove private debug macro and replace with standard version
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org> Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 5 Mar 2007 00:05:44 +0000 (16:05 -0800)]
[NET]: Keep sk_backlog near sk_lock
sk_backlog is a critical field of struct sock. (known famous words)
It is (ab)used in hot paths, in particular in release_sock(), tcp_recvmsg(),
tcp_v4_rcv(), sk_receive_skb().
It really makes sense to place it next to sk_lock, because sk_backlog is only
used after sk_lock locked (and thus memory cache line in L1 cache). This
should reduce cache misses and sk_lock acquisition time.
(In theory, we could only move the head pointer near sk_lock, and leaving tail
far away, because 'tail' is normally not so hot, but keep it simple :) )
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log