Heiko Carstens [Fri, 1 Aug 2008 14:39:11 +0000 (16:39 +0200)]
[S390] nohz/sclp: disable timer on synchronous waits.
sclp_sync_wait wait synchronously for an sclp interrupt and disables
timer interrupts. However on the irq enter paths there is an extra
check if a timer interrupt would be due and calls the timer callback.
This would schedule softirqs in the wrong context.
So introduce local_tick_enable/disable which prevents this.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Michael Holzheu [Fri, 1 Aug 2008 14:39:10 +0000 (16:39 +0200)]
[S390] ipl: Reboot from alternate device does not work when booting from file
During startup we check if diag308 works using diag 308 subcode 6,
which stores the actual ipl information. This fails with rc = 0x102, if
the system has been ipled from the HMC using load from CD or load from file.
In the case of rc = 0x102 we have to assume that diag 308 is working,
since it still can be used to ipl from an alternative device.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When z/VM provides two virtual devices (minidisks) that reside on the
same real device, both will receive the configuration data from the
real device and thus get the same uid. To fix this problem, z/VM
provides an additional configuration data record that allows to
distinguish between minidisks.
z/VM APAR VM64273 needs be installed so this fix has an effect.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The iov_iter_advance() function would look at the iov->iov_len entry
even though it might have iterated over the whole array, and iov was
pointing past the end. This would cause DEBUG_PAGEALLOC to trigger a
kernel page fault if the allocation was at the end of a page, and the
next page was unallocated.
The quick fix is to just change the order of the tests: check that there
is any iovec data left before we check the iov entry itself.
Thanks to Alexey Dobriyan for finding this case, and testing the fix.
Reported-and-tested-by: Alexey Dobriyan <adobriyan@gmail.com> Cc: Nick Piggin <npiggin@suse.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
romfs_readpage: don't report errors for pages beyond i_size
We zero-fill them like we are supposed to, and that's all fine. It's
only an error if the 'romfs_copyfrom()' routine isn't able to fill the
data that is supposed to be there.
Most of the patch is really just re-organizing the code a bit, and using
separate variables for the error value and for how much of the page we
actually filled from the filesystem.
Reported-and-tested-by: Chris Fester <cfester@wms.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Matt Waddel <matt.waddel@freescale.com> Cc: Greg Ungerer <gerg@snapgear.com> Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/mm: Lockless get_user_pages_fast() for 64-bit (v3)
powerpc: Don't use the wrong thread_struct for ptrace get/set VSX regs
powerpc: Fix ptrace buffer size for VSX
powerpc: Correctly hookup PTRACE_GET/SETVSRREGS for 32 bit processes
ide/powermac: Fix use of uninitialized pointer on media-bay
powerpc: Allow non-hcall return values for lparcfg writes
ipmi/powerpc: Use linux/of_{device,platform}.h instead of asm
powerpc/fsl: proliferate simple-bus compatibility to soc nodes
Documentation: remove old sbc8260 board specific information
cpm2: Rework baud rate generators configuration to support external clocks.
powerpc: rtc_cmos_setup: assign interrupts only if there is i8259 PIC
cpm_uart: Add generic clock API support to set baudrates
cpm_uart: Modem control lines support
powerpc: implement GPIO LIB API on CPM1 Freescale SoC.
cpm2: Implement GPIO LIB API on CPM2 Freescale SoC.
powerpc: Fix 8xx build failure
powerpc: clean up the Book-E HW watchpoint support
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
net: Make "networking" one-click deselectable.
ipv6: Fix useless proc net sockstat6 removal
tcp: MD5: Use MIB counter instead of warning for MD5 mismatch.
pkt_sched: Fix OOPS on ingress qdisc add.
niu: Fix error checking in niu_ethflow_to_class.
IPv6: datagram_send_ctl() should exit immediately when an error occured
mac80211: fix mesh beaconing
PS3: gelic: use unsigned long for irqflags
mac80211: fix cfg80211 hooks for master interface
nl80211: fix dump callbacks
mac80211: partially fix skb->cb use
rtl8187: Improve wireless statistics for RTL8187B
rtl8187: Fix for TX sequence number problem
mac80211: append CONFIG_ to MAC80211_VERBOSE_PS_DEBUG in net/mac80211/tx.c.
mac80211: fix sparse integer as NULL pointer warning
drivers/net/wireless/iwlwifi/iwl-led.c: printk fix
mac80211: return correct error return from ieee80211_wep_init
mac80211: tx, use dev_kfree_skb_any for beacon_get
rt2x00: Clear queue entry flags during initialization
rt2x00: Force full register config after start()
...
Dean Nelson [Wed, 30 Jul 2008 05:34:19 +0000 (22:34 -0700)]
sgi-xp: setup the notify GRU message queue
Setup the notify GRU message queue that is used for sending user messages
on UV systems.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:18 +0000 (22:34 -0700)]
sgi-xp: setup the activate GRU message queue
Setup the activate GRU message queue that is used for partition activation
and channel connection on UV systems.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:18 +0000 (22:34 -0700)]
sgi-xp: cleanup naming of partition defines
Cleanup naming of partition defines.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:17 +0000 (22:34 -0700)]
sgi-xp: move xpc_check_remote_hb() to support both SN2 and UV
Move xpc_check_remote_hb() so it can support both SN2 and UV.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:16 +0000 (22:34 -0700)]
sgi-xp: add usage of GRU driver by xpc_remote_memcpy()
Add UV support to xpc_remote_memcpy(), which involves interfacing to the
GRU driver.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:16 +0000 (22:34 -0700)]
sgi-xp: enable building of XPC/XPNET on x86_64
Get XPC/XPNET to build on x86_64. Trying to modprobe them up on a non-UV
or sn2 system will result in a -ENODEV.
Signed-off-by: Dean Nelson <dcn@sgi.com> Cc: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:15 +0000 (22:34 -0700)]
sgi-xp: add 'jiffies' to reserved page's timestamp name
Rename XPC's reserved page's timestamp member to reflect the units of time
involved.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:14 +0000 (22:34 -0700)]
sgi-xp: use standard bitops macros and functions
Change sgi-xp to use the standard bitops macros and functions instead of
trying to invent its own mechanism.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:14 +0000 (22:34 -0700)]
sgi-xp: eliminate '>>>' in comments
Comments in /drivers/misc/sgi-xp has been using '>>>' as a means to draw
attention to something that needs to be done or considered. To avoid
colliding with git rejects, '>>>' will now be replaced by '!!!' to
indicate something to do, and by '???' to indicate something to be
considered.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:13 +0000 (22:34 -0700)]
sgi-xp: add _sn2 suffix to a few variables
Add an '_sn2' suffix to some variables found in xpc_sn2.c.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:13 +0000 (22:34 -0700)]
sgi-xp: isolate remote copy buffer to sn2 only
Make the remote copy buffer an sn2 only item.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:12 +0000 (22:34 -0700)]
sgi-xp: enable XPNET to handle more than 64 partitions
Enable XPNET to support more than 64 partitions.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:11 +0000 (22:34 -0700)]
sgi-xp: isolate allocation of XPC's msgqueues to sn2 only
Move the allocation of XPC's msgqueues to xpc_sn2.c.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:11 +0000 (22:34 -0700)]
sgi-xp: replace AMO_t typedef by struct amo
Replace the AMO_t typedef by a direct reference to 'struct amo'.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:10 +0000 (22:34 -0700)]
sgi-xp: separate chctl_flags from XPC's notify IRQ
Tie current IPI references to either XPC's notify IRQ or channel control
flags.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:09 +0000 (22:34 -0700)]
sgi-xp: isolate additional sn2 specific code
Move additional sn2 specific code into xpc_sn2.c.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:09 +0000 (22:34 -0700)]
sgi-xp: isolate activate IRQ's hardware specific components
Isolate architecture specific code related to XPC's activate IRQ.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:08 +0000 (22:34 -0700)]
sgi-xp: move xpc_allocate() into xpc_send()/xpc_send_notify()
Move xpc_allocate() functionality into xpc_send()/xpc_send_notify() so
xpc_allocate() no longer needs to be called by XPNET.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:07 +0000 (22:34 -0700)]
sgi-xp: base xpc_rsvd_page's timestamp on jiffies
Change XPC's reserved page timestamp to be based on jiffies.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:07 +0000 (22:34 -0700)]
sgi-xp: isolate xpc_vars structure to sn2 only
Isolate the xpc_vars structure of XPC's reserved page to sn2 only.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:06 +0000 (22:34 -0700)]
sgi-xp: isolate xpc_vars_part structure to sn2 only
Isolate the xpc_vars_part structure of XPC's reserved page to sn2 only.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:05 +0000 (22:34 -0700)]
sgi-xp: prepare xpc_rsvd_page to work on either sn2 or uv hardware
Prepare XPC's reserved page header to work for either sn2 or uv.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:05 +0000 (22:34 -0700)]
sgi-xp: create a common xp_remote_memcpy() function
Create a common remote memcpy function that maps to what the hardware
booted supports.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:04 +0000 (22:34 -0700)]
sgi-xp: support runtime selection of xp_max_npartitions
Support runtime selection of the max number of partitions based on the
hardware being run on.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:03 +0000 (22:34 -0700)]
sgi-xp: define BYTES_PER_WORD
Add a BYTES_PER_WORD #define.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:03 +0000 (22:34 -0700)]
sgi-xp: define xpSalError reason code
Define xpSalError reason code.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dean Nelson [Wed, 30 Jul 2008 05:34:02 +0000 (22:34 -0700)]
sgi-xp: define is_shub() and is_uv() macros
Define the is_shub()/is_uv() macros if they've not already been defined.
Signed-off-by: Dean Nelson <dcn@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jack Steiner [Wed, 30 Jul 2008 05:34:02 +0000 (22:34 -0700)]
GRU Driver V3: fixes to resolve code review comments
Fixes problems identified in a code review:
- add comment with high level dscription of the GRU
- prepend "gru_" to all global names
- delete unused function
- couple of trivial bug fixes
[akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Jack Steiner <steiner@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jack Steiner [Wed, 30 Jul 2008 05:33:58 +0000 (22:33 -0700)]
GRU Driver: resource management
This file contains functions realted to managing GRU resources provided to
the user. Examples include GRU context assignment, load, unload,
migration, etc..
Signed-off-by: Jack Steiner <steiner@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jack Steiner [Wed, 30 Jul 2008 05:33:54 +0000 (22:33 -0700)]
GRU Driver: hardware data structures
This series of patches adds a driver for the SGI UV GRU. The driver is
still in development but it currently compiles for both x86_64 & IA64.
All simple regression tests pass on IA64. Although features remain to be
added, I'd like to start the process of getting the driver into the
kernel. Additional kernel drivers will depend on services provide by the
GRU driver.
The GRU is a hardware resource located in the system chipset. The GRU
contains memory that is mmaped into the user address space. This memory
is used to communicate with the GRU to perform functions such as
load/store, scatter/gather, bcopy, AMOs, etc. The GRU is directly
accessed by user instructions using user virtual addresses. GRU
instructions (ex., bcopy) use user virtual addresses for operands.
The GRU contains a large TLB that is functionally very similar to
processor TLBs. Because the external contains a TLB with user virtual
address, it requires callouts from the core VM system when certain types
of changes are made to the process page tables. There are several MMUOPS
patches currently being discussed but none has been accepted into the
kernel. The GRU driver is built using version V18 from Andrea Arcangeli.
This patch:
Contains the definitions of the hardware GRU data structures that are used
by the driver to manage the GRU.
[akpm@linux-foundation;org: export hpage_shift] Signed-off-by: Jack Steiner <steiner@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jack Steiner [Wed, 30 Jul 2008 05:33:53 +0000 (22:33 -0700)]
mm: add zap_vma_ptes(): a library function to unmap driver ptes
zap_vma_ptes() is intended to be used by drivers to unmap ptes assigned to the
driver private vmas. This interface is similar to zap_page_range() but is
less general & less likely to be abused.
Needed by the GRU driver.
Signed-off-by: Jack Steiner <steiner@sgi.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Hugh Dickins <hugh@veritas.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sched: make scheduler sysfs attributes sysdev class devices
They are really class devices, but were incorrectly declared. This
leads to crashes with the recent changes that makes non normal sysdevs
use a different prototype.
The old rtc.c driver did it and some drivers (like rtc-sh) do it in their
release function, though they should not -- because they should provide
the irq_set_state op and the rtc framework itself should care about it.
This patch makes it do so.
I am aware that some drivers, like rtc-sh, handle userspace PIE sets in
their ioctl op (instead of having the framework call the op), exporting
the irq_set_state op at the same time. The logic in rtc_irq_set_state
should make sure it doesn't matter and the driver should not need to care
stopping periodic interrupts in its release routine any more.
The correct way, in my opinion, should be this:
1) The driver provides the irq_set_state op and does not care closing the
interrupts in its release op.
2) If the driver does not provide the op and handles PIE in the ioctl op, it's
reponsible for closing them in its release op.
3) Something similar for other IRQs, like UIE -- if there's no in-kernel API
like irq_set_state, handle it in ioctl and release ops. The framework will
be responsible either for everything or for nothing. (This will probably
change later.)
Signed-off-by: Tomas Janousek <tomi@nomi.cz> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Writes to the cmap fifo while the display is blanked caused cmap FIFO
timeout messages and a wrong colormap. To avoid this the driver now
maintains a colormap in memory and updates the colormap after the display
is unblanked.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Cc: "Antonino A. Daplas" <adaplas@pol.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Harvey Harrison [Wed, 30 Jul 2008 05:33:46 +0000 (22:33 -0700)]
omfs: sparse annotations
Missing cpu_to_be64 on some constant assignments.
fs/omfs/dir.c:107:16: warning: incorrect type in assignment (different base types)
fs/omfs/dir.c:107:16: expected restricted __be64 [usertype] i_sibling
fs/omfs/dir.c:107:16: got unsigned long long
fs/omfs/file.c:33:13: warning: incorrect type in assignment (different base types)
fs/omfs/file.c:33:13: expected restricted __be64 [usertype] e_next
fs/omfs/file.c:33:13: got unsigned long long
fs/omfs/file.c:36:24: warning: incorrect type in assignment (different base types)
fs/omfs/file.c:36:24: expected restricted __be64 [usertype] e_cluster
fs/omfs/file.c:36:24: got unsigned long long
fs/omfs/file.c:37:23: warning: incorrect type in assignment (different base types)
fs/omfs/file.c:37:23: expected restricted __be64 [usertype] e_blocks
fs/omfs/file.c:37:23: got unsigned long long
fs/omfs/bitmap.c:74:18: warning: incorrect type in argument 2 (different signedness)
fs/omfs/bitmap.c:74:18: expected unsigned long volatile *addr
fs/omfs/bitmap.c:74:18: got long *<noident>
fs/omfs/bitmap.c:77:20: warning: incorrect type in argument 2 (different signedness)
fs/omfs/bitmap.c:77:20: expected unsigned long volatile *addr
fs/omfs/bitmap.c:77:20: got long *<noident>
fs/omfs/bitmap.c:112:17: warning: incorrect type in argument 2 (different signedness)
fs/omfs/bitmap.c:112:17: expected unsigned long volatile *addr
fs/omfs/bitmap.c:112:17: got long *<noident>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ben Dooks [Wed, 30 Jul 2008 05:33:44 +0000 (22:33 -0700)]
scripts/mod/modpost.c: fix spelling of module and happens
Spelling fixes in scripts/mod/modpost.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk [Wed, 30 Jul 2008 05:33:44 +0000 (22:33 -0700)]
remove drivers/serial/v850e_uart.c
The removal of drivers/serial/v850e_uart.c originally was in my v850
removal patch, but it seems it got lost somewhere.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Paul Mundt [Wed, 30 Jul 2008 05:33:43 +0000 (22:33 -0700)]
USB: m66592-udc: Fix up dev_set_name() badness.
Commit 0031a06e2f07ab0d1bc98c31dbb6801f95f4bf01 converted all of the USB
drivers to use dev_set_name(), though there was a typo on the m66592-udc
conversion that handed off the wrong pointer (we want the struct device
here obviously, not the struct usb_gadget).
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The file kernel.h contains the upper_32_bits macro. This patch adds the
other part, the lower_32_bits macro. Its first use will be in the driver
for AMD IOMMU.
Cc: H. Peter Anvin <hpa@zytor.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_try_to_free_page: update comments related to vmscan functions
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Cc: Hugh Dickins <hugh@veritas.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swapfile/vmscan: update comments related to vmscan functions
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Cc: Hugh Dickins <hugh@veritas.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Cc: Hugh Dickins <hugh@veritas.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
madvise: update function comment of madvise_dontneed
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp> Cc: Hugh Dickins <hugh@veritas.com> Cc: Nick Piggin <nickpiggin@yahoo.com.au> Cc: Rik van Riel <riel@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit fb6624ebd912e3d6907ca6490248e73368223da9 (initrd: Fix virtual/physical
mix-up in overwrite test) introduced the compiler warning below on mips,
as its virt_to_page() doesn't cast the passed address to unsigned long
internally, unlike on most other architectures:
init/main.c: In function `start_kernel':
init/main.c:633: warning: passing argument 1 of `virt_to_phys' makes pointer from integer without a cast
init/main.c:636: warning: passing argument 1 of `virt_to_phys' makes pointer from integer without a cast
For now, kill the warning by explicitly casting initrd_start to `void *', as
that's the type it should really be.
WANG Cong [Wed, 30 Jul 2008 05:33:34 +0000 (22:33 -0700)]
uml: fix tty-related build error
/home/wangcong/Projects/linux-2.6/arch/um/drivers/line.c: In function `line_write_interrupt':
/home/wangcong/Projects/linux-2.6/arch/um/drivers/line.c:366: error: `struct tty_ldisc' has no member named `write_wakeup'
/home/wangcong/Projects/linux-2.6/arch/um/drivers/line.c:367: error: `struct tty_ldisc' has no member named `write_wakeup'
Signed-off-by: WANG Cong <wangcong@zeuux.org> Cc: Jeff Dike <jdike@addtoit.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
serial8250_startup() doesn't disable interrupts while taking the &up->port.lock
which might race against the interrupt handler serial8250_interrupt(), which
when entered, will deadlock waiting for the lock to be released.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com> Tested-by: Ingo Molnar <mingo@elte.hu> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
markers: fix markers read barrier for multiple probes
Paul pointed out two incorrect read barriers in the marker handler code in
the path where multiple probes are connected. Those are ordering reads of
"ptype" (single or multi probe marker), "multi" array pointer, and "multi"
array data access.
It should be ordered like this :
read ptype
smp_rmb()
read multi array pointer
smp_read_barrier_depends()
access data referenced by multi array pointer
The code with a single probe connected (optimized case, does not have to
allocate an array) has correct memory ordering.
It applies to kernel 2.6.26.x, 2.6.25.x and linux-next.
David Brownell [Wed, 30 Jul 2008 05:33:30 +0000 (22:33 -0700)]
rtc: don't return -EBUSY when mutex_lock_interruptible() fails
It was pointed out that the RTC framework handles its mutex locks oddly
... returning -EBUSY when interrupted. This fixes that by returning the
value of mutex_lock_interruptible() (i.e. -EINTR).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Acked-by: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Julia Lawall [Wed, 30 Jul 2008 05:33:28 +0000 (22:33 -0700)]
drivers/video: release mutex in error handling code
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl> Acked-by: Ondrej Zajicek <santiago@crfreenet.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Li Zefan [Wed, 30 Jul 2008 05:33:23 +0000 (22:33 -0700)]
cpuset: fix wrong calculation of relax domain level
When multiple cpusets are overlapping in their 'cpus' and hence they
form a single sched domain, the largest sched_relax_domain_level among
those should be used. But when top_cpuset's sched_load_balance is
set, its sched_relax_domain_level is used regardless other sub-cpusets'.
This patch fixes it by walking the cpuset hierarchy to find the largest
sched_relax_domain_level.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Cc: Paul Menage <menage@google.com> Cc: Cedric Le Goater <clg@fr.ibm.com> Cc: Balbir Singh <balbir@in.ibm.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lai Jiangshan [Wed, 30 Jul 2008 05:33:22 +0000 (22:33 -0700)]
cpuset: speed up sched domain partition
All child cpusets contain a subset of the parent's cpus, so we can skip
them when partitioning sched domains. This decreases 'csa' greately for
cpusets with multi-level hierarchy.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Cc: Paul Menage <menage@google.com> Cc: Cedric Le Goater <clg@fr.ibm.com> Cc: Balbir Singh <balbir@in.ibm.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Reviewed-by: Paul Jackson <pj@sgi.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[PATCH] inode-diet: Eliminate i_blksize from the inode structure
caused the block size used by pseudo-filesystems to decrease from
PAGE_SIZE to 1024 leading to a doubling of the number of context switches
during a kernbench run.
Signed-off-by: Alex Nixon <Alex.Nixon@citrix.com> Cc: Andi Kleen <andi@firstfloor.org> Cc: Jeremy Fitzhardinge <jeremy@goop.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Ian Campbell <Ian.Campbell@eu.citrix.com> Cc: "Theodore Ts'o" <tytso@mit.edu> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Hugh Dickins <hugh@veritas.com> Cc: Jens Axboe <jens.axboe@oracle.com> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sticore: don't activate unsupported GSC STI cards on HPPA
On HPPA there exists some older GSC graphics cards, which need special
graphic-card-BIOS patching to become supported. Since we don't have yet
implemented the patching, it's better to detect such cards in advance,
inform to the user that there are known problems and to not activate the
card.
Problematic GSC cards and BIOS versions are:
* Hyperdrive/Hyperbowl (A4071A) graphics card series:
* ID = 0x2BCB015A (Version 8.04/8)
* ID = 0x2BCB015A (Version 8.04/11)
* Thunder 1 VISUALIZE 48 card:
* ID = 0x2F23E5FC (Version 8.05/9)
* Thunder 2 VISUALIZE 48 XP card:
* ID = 0x2F8D570E (Version 8.05/12)
* Some Hyperion and ThunderHawk GSC cards
Further details are described here:
http://parisc-linux.org/faq/graphics-howto.html
Signed-off-by: Helge Deller <deller@gmx.de> Cc: Kyle McMartin <kyle@mcmartin.ca> Cc: Krzysztof Helt <krzysztof.h1@poczta.fm> Cc: "Antonino A. Daplas" <adaplas@pol.net> Cc: Grant Grundler <grundler@parisc-linux.org> Cc: Matthew Wilcox <matthew@wil.cx> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Renninger [Wed, 30 Jul 2008 05:32:58 +0000 (22:32 -0700)]
cpufreq acpi: only call _PPC after cpufreq ACPI init funcs got called already
Ingo Molnar provided a fix to not call _PPC at processor driver
initialization time in "[PATCH] ACPI: fix cpufreq regression" (git
commit e4233dec749a3519069d9390561b5636a75c7579)
But it can still happen that _PPC is called at processor driver
initialization time.
This patch should make sure that this is not possible anymore.
Signed-off-by: Thomas Renninger <trenn@suse.de> Cc: Andi Kleen <andi@firstfloor.org> Cc: Len Brown <lenb@kernel.org> Cc: Dave Jones <davej@codemonkey.org.uk> Cc: Ingo Molnar <mingo@elte.hu> Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Magnus Damm [Wed, 30 Jul 2008 05:32:57 +0000 (22:32 -0700)]
resource: add resource_size()
Avoid one-off errors by introducing a resource_size() function.
Signed-off-by: Magnus Damm <damm@igel.co.jp> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Jean Delvare <khali@linux-fr.org> Cc: Paul Mundt <lethal@linux-sh.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Wed, 30 Jul 2008 09:37:46 +0000 (02:37 -0700)]
pkt_sched: Fix OOPS on ingress qdisc add.
Bug report from Steven Jan Springl:
Issuing the following command causes a kernel oops:
tc qdisc add dev eth0 handle ffff: ingress
The problem mostly stems from all of the special case handling of
ingress qdiscs.
So, to fix this, do the grafting operation the same way we do for TX
qdiscs. Which means that dev_activate() and dev_deactivate() now do
the "qdisc_sleeping <--> qdisc" transitions on dev->rx_queue too.
Future simplifications are possible now, mainly because it is
impossible for dev_queue->{qdisc,qdisc_sleeping} to be NULL. There
are NULL checks all over to handle the ingress qdisc special case
that used to exist before this commit.
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6: datagram_send_ctl() should exit immediately when an error occured
When an error occured, datagram_send_ctl() should exit immediately rather than
continue to run the for loop. Otherwise, the variable err might be changed and
the error might be hidden.
Fix this bug by using "goto" instead of "break".
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log