[POWERPC] mpc5200: Fix FEC error handling on FIFO errors
The error handling for the mpc5200 fec interrupt is broken. The intended
behaviour is like this:
* If one of FEC_IEVENT_RFIFO_ERROR and FEC_IEVENT_XFIFO_ERROR happens,
the datasheet says (MPC5200B User's Guide R1.2, p. 14-13): "When this
occurs, software must ensure both the FIFO Controller and BestComm are
soft-reset".
* On any other error (non-TFINT) interrupt, just issue a debug message.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[POWERPC] mpc5200: add Phytec pcm030 board support
Add board support for the Phytec pcm030 mpc5200b based board. It
does not need any platform specific fixups and as such is handled
as a mpc5200 simple platform.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The RapidIO system size will auto probe in RIO setup. The route table
and rionet_active in rionet.c are changed to be allocated dynamically
according to the size of the system.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[RAPIDIO] Add OF-tree support to RapidIO controller driver
This initializes the RapidIO controller driver using addresses and
interrupt numbers obtained from the firmware device tree, rather than
using hardcoded constants.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
The original RapidIO driver suppose there is only one mpc85xx RIO controller
in system. So, some data structures are defined as mpc85xx_rio global, such
as 'regs_win', 'dbell_ring', 'msg_tx_ring'. Now, I changed them to mport's
private members. And you can define multi RIO OF-nodes in dts file for multi
RapidIO controller in one processor, such as PCI/PCI-Ex host controllers in
Freescale's silicon. And the mport operation function declaration should be
changed to know which RapidIO controller is target.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Provide walk_memory_resource() for powerpc
Provide walk_memory_resource() for 64-bit powerpc. PowerPC maintains
logical memory region mapping in the lmb.memory structure. Walk
through these structures and do the callbacks for the contiguous
chunks.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Update lmb data structures for hotplug memory add/remove
The powerpc kernel maintains information about logical memory blocks
in the lmb.memory structure, which is initialized and updated at boot
time, but not when memory is added or removed while the kernel is
running.
This adds a hotplug memory notifier which updates lmb.memory when
memory is added or removed. This information is useful for eHEA
driver to find out the memory layout and holes.
NOTE: No special locking is needed for lmb_add() and lmb_remove().
Calls to these are serialized by caller. (pSeries_reconfig_chain).
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[POWERPC] Hotplug memory remove notifications for powerpc
Hotplug memory remove notifier for 64-bit powerpc. This gets invoked
by writing to /proc/ppc64/ofdt the string "remove_node " followed by
the firmware device tree pathname of the node that needs to be removed.
In response, this adjusts the sections and removes sysfs entries by
calling __remove_pages(). Then it calls arch-specific code to get rid
of the hardware MMU mappings for the section of memory.
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com> Reviewed-by: Michael Ellerman <michael@ellerman.id.au> Cc: Yasunori Goto <y-goto@jp.fujitsu.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements a new driver named windfarm_pm121, which drives the
fans on PowerMac 12,1 machines : iMac G5 iSight (rev C) 17" and
20". It's based on the windfarm_pm81 driver from Benjamin
Herrenschmidt.
This includes fixes from David Woodhouse correcting the names of some
of the sensors.
Signed-off-by: Étienne Bersac <bersace@gmail.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Tony Breeds [Tue, 29 Apr 2008 01:42:32 +0000 (11:42 +1000)]
[POWERPC] Fix building of pmac32 when CONFIG_NVRAM=m
Kamalesh Babulal (kamalesh@linux.vnet.ibm.com) reports that CONFIG_NVRAM=m
is valid in terms of Kconfig but fails to build with:
Building modules, stage 2.
MODPOST 1401 modules
ERROR: "pmac_newworld" [arch/powerpc/platforms/powermac/nvram.ko] undefined!
ERROR: "__alloc_bootmem" [arch/powerpc/platforms/powermac/nvram.ko] undefined!
make[1]: *** [__modpost] Error
The arch/powerpc/platforms/powermac/nvram.c code really needs to be
builtin, but as its compilation is dependent on a generic Kconfig
symbol we force nvram.c to be builtin if CONFIG_NVRAM is 'y' or 'm'.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Kumar Gala [Mon, 28 Apr 2008 06:21:22 +0000 (16:21 +1000)]
[POWERPC] Add IRQSTACKS support on ppc32
This makes it possible to use separate stacks for hard and soft IRQs
on 32-bit powerpc as well as on 64-bit. The code for 32-bit is just
the 32-bit analog of the 64-bit code.
* Added allocation and initialization of the irq stacks. We limit the
stacks to be in lowmem for ppc32.
* Implemented ppc32 versions of call_do_softirq() and call_handle_irq()
to switch the stack pointers
* Reworked how we do stack overflow detection. We now keep around the
limit of the stack in the thread_struct and compare against the limit
to see if we've overflowed. We can now use this on ppc64 if desired.
[ paulus@samba.org: Fixed bug on 6xx where we need to reload r9 with the
thread_info pointer. ]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Mon, 28 Apr 2008 04:44:08 +0000 (14:44 +1000)]
[POWERPC] Use __always_inline for xchg* and cmpxchg*
This changes the definitions of the xchg and cmpxchg families of
functions in include/asm-powerpc/system.h to be marked __always_inline
rather than __inline__. The reason for doing this is that we rely on
the compiler inlining them in order to eliminate the references to
__xchg_called_with_bad_pointer and __cmpxchg_called_with_bad_pointer,
which are deliberately left undefined. Thus this change will enable
us to make the inline keyword be just a hint rather than a directive.
Paul Mackerras [Mon, 28 Apr 2008 03:52:31 +0000 (13:52 +1000)]
[POWERPC] Add fast little-endian switch system call
This adds a system call on 64-bit platforms for switching between
little-endian and big-endian modes that is much faster than doing a
prctl call. This system call is handled as a special case right at
the start of the system call entry code, and because it is a special
case, it uses a system call number which is out of the range of
normal system calls, namely 0x1ebe.
Measurements with lmbench on a 4.2GHz POWER6 showed no measurable
change in the speed of normal system calls with this patch.
Switching endianness with this new system call takes around 60ns on a
4.2GHz POWER6, compared with around 300ns to switch endian mode with a
prctl. This can provide a significant performance advantage for
emulators for little-endian architectures that want to switch between
big-endian and little-endian mode frequently, e.g. because they are
generating instructions sequences on the fly and they want to run
those sequences in little-endian mode.
The other thing about this system call is that it doesn't clobber as
many registers as a normal system call. It only clobbers r12.
Harvey Harrison [Mon, 28 Apr 2008 23:50:03 +0000 (16:50 -0700)]
media: fix integer as NULL pointer warnings
drivers/media/video/v4l2-common.c:719:16: warning: Using plain integer as NULL pointer
drivers/media/video/au0828/au0828-dvb.c:122:19: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1101:22: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1102:23: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-audio.c:78:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-video-v4l.c:84:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:1264:9: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-context.c:197:28: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-cx2584x-v4l.c:126:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:133:32: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:145:31: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:177:55: warning: Using plain integer as NULL pointer
drivers/media/video/videobuf-core.c:100:9: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Harvey Harrison [Mon, 28 Apr 2008 23:50:03 +0000 (16:50 -0700)]
scsi: fix integer as NULL pointer warnings
drivers/scsi/aic7xxx/aic7770_osm.c:53:58: warning: Using plain integer as NULL pointer
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c:355:47: warning: Using plain integer as NULL pointer
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c:372:55: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:997:28: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:1003:28: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:1165:46: warning: Using plain integer as NULL pointer
drivers/scsi/fdomain.c:1446:40: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:1650:51: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:3171:42: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:5732:52: warning: Using plain integer as NULL pointer
drivers/scsi/ncr53c8xx.c:8189:31: warning: Using plain integer as NULL pointer
drivers/scsi/ncr53c8xx.c:8225:34: warning: Using plain integer as NULL pointer
drivers/scsi/dpt_i2o.c:156:32: warning: Using plain integer as NULL pointer
drivers/scsi/ultrastor.c:954:42: warning: Using plain integer as NULL pointer
drivers/scsi/ultrastor.c:1104:18: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kconfig: add named choice group
kconfig: fix choice dependency check
kconifg: 'select' considered less evil
dontdiff: ignore timeconst.h
dontdiff: add modules.order
kbuild: fix unportability in gen_initramfs_list.sh
kbuild: fix help output to show correct arch
kbuild: show defconfig subdirs in make help
kconfig: reversed borderlines in inputbox
Harvey Harrison [Mon, 28 Apr 2008 21:13:20 +0000 (14:13 -0700)]
drivers: atm, char fix integer as NULL pointer warnings
drivers/atm/nicstar.c:418:25: warning: Using plain integer as NULL pointer
drivers/char/drm/r128_cce.c:820:25: warning: Using plain integer as NULL pointer
drivers/char/tty_io.c:1183:10: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Harvey Harrison [Mon, 28 Apr 2008 21:13:19 +0000 (14:13 -0700)]
kernel: fix integer as NULL pointer warnings
kernel/cpuset.c:1268:52: warning: Using plain integer as NULL pointer
kernel/pid_namespace.c:95:24: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Reviewed-by: Paul Jackson <pj@sgi.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sergei Shtylyov [Mon, 28 Apr 2008 21:44:44 +0000 (23:44 +0200)]
siimage: coding style cleanup (take 2)
Fix 18 errors and several warnings given by checkpatch.pl:
- use of C99 // comments;
- trailing whitespace;
- 'switch' and 'case' not at the same indentation level;
- no space before the open parenthesis of the 'if' and 'switch' statements;
- space between function name and open parenthesis (though I have introduced
such warnins in some places since the code looks prettier with the spaces);
- including <asm/io.h> instead of <linux/io.h>;
- line over 80 characters.
In addition to these changes, also do the following:
- make the arrays in sil_set_pio_mode() 'static', and make the arrays in
sil_set_dma_mode() 'static const';
- change the string of the 'if' statements into the 'switch' statement in
sil_pata_udma_filter();
- drop the needless '==' operators from the 'if' statements where a condition
is a mere bit test;
- remove needless initializer for the 'tmp' variable in init_chipset_siimage();
- beautify groups of the variable initializers and assignment operators;
- add new line after variable definitions;
- remove new line between the comment and the statements it refers to;
- remove needless curly braces and parentheses;
- fix typos, capitalize acronyms, etc. in the comments...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Adrian Bunk [Mon, 28 Apr 2008 21:44:43 +0000 (23:44 +0200)]
ARM: always select HAVE_IDE
It's plain wrong for PCMCIA to select HAVE_IDE that implies e.g. the
availability of an asm/ide.h
It turns out this was done for ARM, and we can simply always select
HAVE_IDE on ARM instead of manually tracking which platforms might
possible have an IDE controller directly or indirectly.
Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Russell King <rmk+lkml@arm.linux.org.uk> Cc: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Adrian Bunk [Mon, 28 Apr 2008 21:44:42 +0000 (23:44 +0200)]
remove the broken ETRAX_IDE driver
ETRAX_IDE was marked as broken last year with the comment
"it doesn't even compile currently".
Remove it since it won't get fixed in the near future.
On Mon, Apr 14, 2008 at 02:50:19PM +0200, Mikael Starvik wrote:
> You can remove it for now and we will resubmit a new if/when we get around
> to fix it.
[bart: ported it over IDE tree]
Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Mikael Starvik <mikael.starvik@axis.com> Cc: Jesper Nilsson <Jesper.Nilsson@axis.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ide_pad_transfer() helper (which uses ->{in,out}put_data methods
internally so the transfer is also padded to drive+host requirements)
and use it instead of ide_atapi_{write_zeros,discard_data}().
* Remove no longer needed ide_atapi_{write_zeros,discard_data}().
Add sil_iowrite{8,16,32}() and sil_ioread{8,16}() helpers, then use them to
merge code accessing configuration registers through PCI and MMIO together.
[ because of this SATA initialization bits from setup_mmio_siimage() are
moved to init_chipset_siimage() ]
This also cuts code size a bit:
text data bss dec hex filename
4437 164 0 4601 11f9 drivers/ide/pci/siimage.o.before
3979 164 0 4143 102f drivers/ide/pci/siimage.o.after
While at it:
* Use I/O ops directly instead of using ->IN{B,W} and ->OUT{B,W}.
* Fixup CodingStyle in setup_mmio_siimage().
* Rename 'tmpbyte' variable to 'tmp' in init_chipset_siimage().
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ins{w,l}()/outs{w,l}() and __ide_mm_ins{w,l}()/__ide_mm_outs{w,l}()
directly in ata_{in,out}put_data() (by using IDE_HFLAG_MMIO host flag to
decide which I/O ops are required).
* Remove no longer needed ->INS{W,L} and ->OUTS{W,L} methods (ide-h8300,
au1xxx-ide and scc_pata implement their own ->{in,out}put_data methods).
There should be no functional changes caused by this patch.
ide: merge ->atapi_*put_bytes and ->ata_*put_data methods
* Merge ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods
into new ->{in,out}put_data methods which take number of bytes to
transfer as an argument and always do padding.
While at it:
* Use 'hwif' or 'drive->hwif' instead of 'HWIF(drive)'.
There should be no functional changes caused by this patch (all users
of ->ata_{in,out}put_data methods were using multiply-of-4 word counts).
falconide/q40ide: add ->atapi_*put_bytes and ->ata_*put_data methods (take 2)
* Add ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods to
falconide and q40ide host drivers (->ata_* methods are implemented on
top of ->atapi_* methods so they also do byte-swapping now).
* Cleanup atapi_{in,out}put_bytes().
v2:
* Add 'struct request *rq' argument to ->ata_{in,out}put_data methods
and don't byte-swap disk fs requests (we shouldn't un-swap fs requests
because fs itself is stored byte-swapped on the disk) - this is how
things were done before the patch (ideally device mapper should be
used instead but it would break existing setups and would have some
performance impact).
Cc: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Michael Schmitz <schmitz@debian.org> Cc: Roman Zippel <zippel@linux-m68k.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: Richard Zidlicky <rz@linux-m68k.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Monday 28 April 2008, Sergei Shtylyov wrote:
> Hello, I wrote:
>
> > Fix these warnings emitted when compiling drivers/ide/mips/au1xxx-ide.c:
>
> > include/asm/mach-au1x00/au1xxx_ide.h:137: warning: 'auide_tune_drive' declared
> > `static' but never defined
> > include/asm/mach-au1x00/au1xxx_ide.h:138: warning: 'auide_tune_chipset' declared
> > `static' but never defined
>
> > by wiping out the whole "function prototyping" section from the header file
> > <asm-mips/mach-au1x00/au1xxx_ide.h> as it mostly declared functions that are
> > already dead in the IDE driver; move the only useful prototype into the driver.
> >
> > Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
>
> > ---
> > I'm not sure thru which tree this should go -- probably thru Linux/MIPS one...
>
> > Bart, au1xxx-ide-fix-mwdma-support.patch will probably need to be updated to
> > remove that added prototype since it won't be needed anymore...
>
> Which you haven't done either in that patch or in
> au1xxx-ide-use-init_dma-method.patch. So, face the consequences:
>
> drivers/ide/mips/au1xxx-ide.c:456: error: conflicting types for 'auide_ddma_init'
> drivers/ide/mips/au1xxx-ide.c:51: error: previous declaration of
> 'auide_ddma_init' was here
> drivers/ide/mips/au1xxx-ide.c:456: error: conflicting types for 'auide_ddma_init'
> drivers/ide/mips/au1xxx-ide.c:51: error: previous declaration of
> 'auide_ddma_init' was here
> drivers/ide/mips/au1xxx-ide.c:51: warning: 'auide_ddma_init' used but never
> defined
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Roland McGrath [Mon, 28 Apr 2008 20:57:19 +0000 (13:57 -0700)]
ptrace: conditionalize compat_ptrace_request
My recent additions to compat_ptrace_request made it mandatory
for CONFIG_COMPAT arch's to define copy_siginfo_from_user32.
This broke some builds, though they all really should get cleaned
up in that way.
Since all the arch's that actually call compat_ptrace_request have
now been cleaned up to use the generic compat_sys_ptrace, we can
avoid the build problems on the crufty arch's by changing the
conditionals on the definition.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: pack objects denser
slub: Calculate min_objects based on number of processors.
slub: Drop DEFAULT_MAX_ORDER / DEFAULT_MIN_OBJECTS
slub: Simplify any_slab_object checks
slub: Make the order configurable for each slab cache
slub: Drop fallback to page allocator method
slub: Fallback to minimal order during slab page allocation
slub: Update statistics handling for variable order slabs
slub: Add kmem_cache_order_objects struct
slub: for_each_object must be passed the number of objects in a slab
slub: Store max number of objects in the page struct.
slub: Dump list of objects not freed on kmem_cache_close()
slub: free_list() cleanup
slub: improve kmem_cache_destroy() error message
slob: fix bug - when slob allocates "struct kmem_cache", it does not force alignment.
Roman Zippel [Fri, 29 Feb 2008 04:11:50 +0000 (05:11 +0100)]
kconfig: add named choice group
As choice dependency are now fully checked, it's quite easy to add support
for named choices. This lifts the restriction that a choice value can only
appear once, although it still has to be within the same group,
but multiple choices can be joined by giving them a name.
While at it I cleaned up a little the choice type logic to simplify it a
bit.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Roman Zippel [Fri, 29 Feb 2008 04:10:24 +0000 (05:10 +0100)]
kconfig: fix choice dependency check
Properly check the dependency of choices as a group.
Also fix that sym_check_deps() correctly terminates the dependency loop
error check (otherwise it would continue printing the dependency chain).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Felix Fietkau [Wed, 2 Apr 2008 12:50:05 +0000 (14:50 +0200)]
kbuild: fix unportability in gen_initramfs_list.sh
On a Mac OS X machine the output of ls -l is different from a standard
Linux machine. Use readlink instead of parsing a hardcoded field number
from the ls output.
Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Roland McGrath [Mon, 28 Apr 2008 01:45:38 +0000 (18:45 -0700)]
x86_64 vDSO: use initdata
The 64-bit vDSO image is in a special ".vdso" section for no reason
I can determine. Furthermore, the location of the vdso_end symbol
includes some wrongly-calculated padding space in the image, which
is then (correctly) rounded to page size, resulting in an extra page
of zeros in the image mapped in to user processes.
This changes it to put the vdso.so image into normal initdata as we
have always done for the 32-bit vDSO images. The extra padding is
gone, so the user VMA is one page instead of two. The image that
was already copied around at boot time is now in initdata, so we
recover that wasted space after boot.
Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Make acpi-cpufreq more robust against BIOS freq changes behind our back.
[CPUFREQ] change cpu freq tables to per_cpu variables
[CPUFREQ] fix show_trans_table
[CPUFREQ] Warn when cpufreq_register_notifier called before pure initcalls
[CPUFREQ] Refactor locking in cpufreq_add_dev
[CPUFREQ] more CodingStyle
[CPUFREQ] CodingStyle
[CPUFREQ] Slightly shorten the error paths of cpufreq_suspend/cpufreq_resume
CC mm/memory_hotplug.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/memory_hotplug.c: In function ‘put_page_bootmem’:
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/memory_hotplug.c:82: error: implicit declaration of function ‘__free_pages_bootmem’
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/memory_hotplug.c: At top level:
/home/bunk/linux/kernel-2.6/git/linux-2.6/mm/memory_hotplug.c:87: warning: no previous prototype for ‘register_page_bootmem_info_section’
make[2]: *** [mm/memory_hotplug.o] Error 1
[ Andrew: "Argh. The -mm-only memory-hotplug-add-removable-to-sysfs-
to-show-memblock-removability.patch debugging patch adds that include
so nobody hit this before. ]
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PowerPC will start moving board defconfigs into subarch-specific
subdirs soon. "make help" currently does not look in subdirs to
find the defconfigs to show. This is partially a good thing,
since there are way too many defconfigs for one list.
This patch makes the main "make help" display something like
help-40x - Show 40x-specific targets
help-44x - Show 44x-specific targets
help-boards - Show all of the above
and wires up stuff so those new help-* commands actually work.
[sam: fixed it up to display x86 defconfigs too] Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
[CPUFREQ] Make acpi-cpufreq more robust against BIOS freq changes behind our back.
We checked the hardware freq with OS cached freq value in get_cur_freqon_cpu().
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Thomas Renninger <trenn@suse.de> Signed-off-by: Dave Jones <davej@redhat.com>
* Not all snprintf calls were protected against being passed a negative
length.
* When show_trans_table overflows, len might be > PAGE_SIZE. In that case,
returns PAGE_SIZE.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net> Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
[CPUFREQ] Warn when cpufreq_register_notifier called before pure initcalls
If cpufreq_register_notifier is called before pure initcalls,
init_cpufreq_transition_notifier_list will overwrite whatever it did,
causing notifiers to be ignored.
Print some noise to the kernel log if that happens.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net> Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
This bug was introduced in the 2.6.24 i386/x86_64 tree merge, where
MSI-X vector allocation will eventually fail. The cause is the new
bit array tracking used vectors is not getting cleared properly on
IRQ destruction on the 32-bit APIC code.
This can be seen easily using the ixgbe 10 GbE driver on multi-core
systems by simply loading and unloading the driver a few times.
Depending on the number of available vectors on the host system, the
MSI-X allocation will eventually fail, and the driver will only be
able to use legacy interrupts.
I am generating the same patch for both stable trees for 2.6.24 and
2.6.25.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
SELinux: Fix a RCU free problem with the netport cache
SELinux: Made netnode cache adds faster
SELinux: include/security.h whitespace, syntax, and other cleanups
SELinux: policydb.h whitespace, syntax, and other cleanups
SELinux: mls_types.h whitespace, syntax, and other cleanups
SELinux: mls.h whitespace, syntax, and other cleanups
SELinux: hashtab.h whitespace, syntax, and other cleanups
SELinux: context.h whitespace, syntax, and other cleanups
SELinux: ss/conditional.h whitespace, syntax, and other cleanups
SELinux: selinux/include/security.h whitespace, syntax, and other cleanups
SELinux: objsec.h whitespace, syntax, and other cleanups
SELinux: netlabel.h whitespace, syntax, and other cleanups
SELinux: avc_ss.h whitespace, syntax, and other cleanups
Fixed up conflict in include/linux/security.h manually
projects / linux-2.6 / log