Salyzyn, Mark [Wed, 6 Feb 2008 21:54:12 +0000 (13:54 -0800)]
[SCSI] aacraid: do not set valid bit in sense information
Luben Tuikov [mailto:ltuikov@yahoo.com] sez:
> Just as in your case and Tony's case, which I presume
> uses the same RAID firmware vendor, it would've
> probably been better if the RAID firmware vendor
> fixed the firmware to not set the VALID bit if the
> INFORMATION field is not valid.
Point taken regarding the aacraid driver. Dropped the VALID bit, and
then did some cleanup/simplification of the set_sense procedure and
the associated parameters. Mike did some preliminary tests when the
VALID bit was dropped before the 'Re: [PATCH] [SCSI] sd: make error
handling more robust' patches came on the scene. The change in the
SCSI subsystem does make this enclosed aacraid patch unnecessary, so
this aacraid patch is merely post battle ground cleanup. If the
simplification is an issue, repugnant, too much for a back-port to the
stable trees or clouds the point, this patch could be happily
distilled down to:
James Bottomley [Sun, 3 Feb 2008 21:48:56 +0000 (15:48 -0600)]
[SCSI] ses: add new Enclosure ULD
This adds support to SCSI for enclosure services devices. It also makes
use of the enclosure services added in an earlier patch to display the
enclosure topology in sysfs.
At the moment, the enclosures are SAS specific, but if anyone actually
has a non-SAS enclosure that follows the SES-2 standard, we can add that
as well.
On my Vitesse based system, the enclosures show up like this:
You can flash the various blinky lights by echoing to the fault and locate files.
>From the device's point of view, you can see it has an enclosure like this:
sparkweed:~# ls /sys/class/scsi_disk/0\:0\:0\:0/device/
block:sda generic queue_depth state
bsg:0:0:0:0 iocounterbits queue_type subsystem
bus iodone_cnt rescan timeout
delete ioerr_cnt rev type
device_blocked iorequest_cnt scsi_device:0:0:0:0 uevent
driver modalias scsi_disk:0:0:0:0 vendor
enclosure_component:SLOT 001 model scsi_generic:sg0
evt_media_change power scsi_level
Note the enclosure_component:SLOT 001 which shows where in the enclosure
this device fits.
The astute will notice that I'm using SCSI VPD Inquiries to identify the
devices. This, unfortunately, won't work for SATA devices unless we do
some really nasty hacking about on the SAT because the only think that
knows the SAS addresses for SATA devices is libsas, not libata where the
SAT resides.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Wed, 6 Feb 2008 19:01:58 +0000 (13:01 -0600)]
[SCSI] sr: fix test unit ready responses
Commit 210ba1d1724f5c4ed87a2ab1a21ca861a915f734 updated sr.c to use
the scsi_test_unit_ready() function. Unfortunately, this has the
wrong characteristic of eating NOT_READY returns which sr.c relies on
for tray status.
Fix by rolling an internal sr_test_unit_ready() that doesn't do this.
Tested-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Roel Kluin [Wed, 6 Feb 2008 18:21:07 +0000 (19:21 +0100)]
[SCSI] u14-34f: fix data direction bug
Direction of data transfer 'DMA_FROM_DEVICE' was tested twice. DTD_OUT
means transfer from host to device. This should occur when the
direction of data transfer (sc_data_direction) is 'DMA_TO_DEVICE'.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Salyzyn, Mark [Wed, 6 Feb 2008 17:00:46 +0000 (09:00 -0800)]
[SCSI] aacraid: pci_set_dma_max_seg_size opened up for late model controllers
This patch ensures that the modern adapters get a maximum sg segment
size on par with the maximum transfer size. Added some localized
janitor fixes to the discussion patch I used with Fujita.
FUJITA Tomonori [mailto:fujita.tomonori@lab.ntt.co.jp] sez:
> I think that setting the proper maximum segment size for the late
> model cards (as you did above) makes sense.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tony Battersby [Tue, 5 Feb 2008 15:36:10 +0000 (10:36 -0500)]
[SCSI] fix BUG when sum(scatterlist) > bufflen
When sending a SCSI command to a tape drive via the SCSI Generic (sg)
driver, if the command has a data transfer length more than
scatter_elem_sz (32 KB default) and not a multiple of 512, then I either
hit BUG_ON(!valid_dma_direction(direction)) in dma_unmap_sg() or else
the command never completes (depending on the LLDD).
When constructing scatterlists, the sg driver rounds up the scatterlist
element sizes to be a multiple of 512. This can result in
sum(scatterlist lengths) > bufflen. In this case, scsi_req_map_sg()
incorrectly sets bio->bi_size to sum(scatterlist lengths) rather than to
bufflen. When the command completes, req_bio_endio() detects that
bio->bi_size != 0, and so it doesn't call bio_endio(). This causes the
command to be resubmitted, resulting in BUG_ON or the command never
completing.
This patch makes scsi_req_map_sg() set bio->bi_size to bufflen rather
than to sum(scatterlist lengths), which fixes the problem.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Acked-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Nick Cheng [Tue, 5 Feb 2008 07:53:24 +0000 (23:53 -0800)]
[SCSI] arcmsr: updates (1.20.00.15)
- add arcmsr_enable_eoi_mode()and readl(reg->iop2drv_doorbell_reg) in
arcmsr_handle_hbb_isr() on adapter Type B in case of the doorbell
interrupt clearance is cached
- add conditional declaration for arcmsr_pci_error_detected() and
arcmsr_pci_slot_reset
- check if the sg list member number exceeds arcmsr default limit in
arcmsr_build_ccb()
- change the returned value type of arcmsr_build_ccb()from "void" to
"int" returns FAILED in arcmsr_queue_command()
- modify arcmsr_drain_donequeue() to ignore unknown command and let
kernel process command timeout. This could handle IO request violating
maximum segments, i.e. Linux XFS over DM-CRYPT. Thanks to Milan Broz's
comments <mbroz@redhat.com>
- fix the release of dma memory for type B in arcmsr_free_ccb_pool()
- fix the arcmsr_polling_hbb_ccbdone()
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw> Cc: Milan Broz <mbroz@redhat.com> Cc: <thenzl@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adrian Bunk [Tue, 5 Feb 2008 07:53:19 +0000 (23:53 -0800)]
[SCSI] advansys: make 3 functions static
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Pavel Machek [Tue, 5 Feb 2008 07:53:24 +0000 (23:53 -0800)]
[SCSI] Small cleanups for scsi_host.h
Small cleanups in scsi_host.h. Few #defines make me wonder if their
description is still up to date..?
Signed-off-by: Pavel Machek <pavel@suse.cz> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Bottomley [Sat, 2 Feb 2008 22:06:23 +0000 (16:06 -0600)]
[SCSI] sd: handle bad lba in sense information
Some devices report medium error locations incorrectly. Add guards to
make sure the reported bad lba is actually in the request that caused
it. Additionally remove the large case statment for sector sizes and
replace it with the proper u64 divisions.
Tested-by: Mike Snitzer <snitzer@gmail.com> Cc: Stable Tree <stable@kernel.org> Cc: Tony Battersby <tonyb@cybernetics.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vasquez [Thu, 31 Jan 2008 20:33:53 +0000 (12:33 -0800)]
[SCSI] qla2xxx: Correct issue where incorrect init-fw mailbox command was used on non-NPIV capable ISPs.
BIT_2 of the firmware attributes is only valid on FW-interface-2
type HBAs. Code in commit c48339decceec8e011498b0fc4c7c7d8b2ea06c1 would cause the
incorrect initialize-firmware mailbox command to be issued for
non-NPIV capable ISPs. Correct this by reverting to previously
used (and correct) pre-condition 'if' check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Seokmann Ju [Thu, 31 Jan 2008 20:33:52 +0000 (12:33 -0800)]
[SCSI] qla2xxx: Access the proper 'physical' port in FC-transport callbacks.
For following fc_host specific attributes, vports rely on the pport.
So, this patch changed way to access the data for those attributes so that
they can access pport's.
- get_host_speed (speed)
- get_host_port_state (port_state)
- get_host_port_type (port_type)
- get_fc_host_stats
Also, added PORT_SPEED_8GB case in the speed attribute for 8Gb HBAs.
Signed-Off-by: Seokmann Ju <seokmann.ju@qlogic.com> Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Seokmann Ju [Thu, 31 Jan 2008 20:33:51 +0000 (12:33 -0800)]
[SCSI] qla2xxx: Correct issue where vport-state was not updated during an ISP_ABORT_NEEDED requst.
While running IO simultaneously through physical port and virtual
port, if user changes Data Rate (from scli utility), IO through
virtual port fails. It failed because the vport had not received
the ISP_ABORT_NEEDED notification.
Signed-Off-by: Seokmann Ju <seokmann.ju@qlogic.com> Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vasquez [Thu, 31 Jan 2008 20:33:50 +0000 (12:33 -0800)]
[SCSI] qla2xxx: Move RISC-interrupt-register modifications to qla2x00_request_irqs().
There's no functional change involved with this update, instead
it simply migrates the "set cleared interrupt state" codes to a
more approprate method, qla2x00_request_irqs(), and cleans-up the
driver's probe() logic.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vasquez [Thu, 31 Jan 2008 20:33:48 +0000 (12:33 -0800)]
[SCSI] qla2xxx: Cleanse memory allocation logic during probe.
- Drop loop-till-allocated structure of code within
qla2x00_mem_alloc().
- Properly unwind deallcations of memory during failures.
- Drop qla2x00_allocate_sp_pool() and qla2x00_free_sp_pool()
functions as their implementations can easily be collapsed into
the callers.
- Defer DMA pool allocation of SFP data until requested.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vasquez [Thu, 31 Jan 2008 20:33:46 +0000 (12:33 -0800)]
[SCSI] qla2xxx: Cleanup any outstanding SRB resources during shutdown.
Refactor SRB-failure completion codes in the process. Also,
signal the DPC routine to complete sooner as backend processing
at shutdown-time is superflous.
[jejb: resolve conflicts with pci_enable_device_bars removal]
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Andrew Vasquez [Thu, 31 Jan 2008 20:33:44 +0000 (12:33 -0800)]
[SCSI] qla2xxx: Correct resource_size_t usages.
Hmm, it looks like the conversion to resource_size_t usage
(3776541d8a46347a4924353a192c6ce4a3d04e2e) requires some additional
fixups to cleanup the structure-pointer castings used during IO mapped
accesses to the chip.
There's only a small number of locations, where the driver uses IO
mapped accesses to the hardware, the patch below should take care of
it without introducing to many structural changes to code flow.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 31 Jan 2008 19:36:53 +0000 (13:36 -0600)]
[SCSI] libiscsi: fix session age rollover and remove cid encoding
The session age mask is only 4 bits, but session->age is 32. When
it gets larger then 15 and we try to or the bits some bits get
dropped and the check for session age in iscsi_verify_itt is useless.
The ISCSI_CID_MASK related bits are also useless since cid is always
one.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 31 Jan 2008 19:36:52 +0000 (13:36 -0600)]
[SCSI] iscsi: fix up iscsi printk prefix
Some iscsi class messages have the dev_printk prefix and some libiscsi
and iscsi_tcp messages have "iscsi" or the module name as a prefix which
is normally pretty useless when trying to figure out which session
or connection the message is attached to. This patch adds iscsi lib
and class dev_printks so all messages have a common prefix that
can be used to figure out which object printed it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 31 Jan 2008 19:36:51 +0000 (13:36 -0600)]
[SCSI] iscsi class: fix iscsi conn attr counter
There are 13 iscsi conn attrs, but since the IF/OF markers were not being
used we did not notice that we forgot to increment the ISCSI_CONN_ATTRS
counter.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 31 Jan 2008 19:36:49 +0000 (13:36 -0600)]
[SCSI] qla4xxx: add async scan support
qla4xxx has the old school startup/probe where it finds presetup sessions
in its flash and then attempts to log into them before returning from the
probe. This however, makes it very simple to add a iscsi class scan finished
helper which the driver can use.
In future patches Dave or I will rip apart the driver to make it more
like qla2xxx, but for now this is a very simple two line patch which
fixes the problem of trying to figure out when the initial sessions
are done being scanned.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Cc: David Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 31 Jan 2008 19:36:48 +0000 (13:36 -0600)]
[SCSI] iscsi class: add async scan helper
In qla4xxx's probe it will call the iscsi session setup functions
for session that got setup on the initial start. This then makes
it easy for the iscsi class to export a helper which indicates
when those scans are done.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 31 Jan 2008 19:36:47 +0000 (13:36 -0600)]
[SCSI] qla4xxx: fix recovery timer and session unblock race
If qla4xxx is resetting up a session and the recovery timer
fires we do not want to just set it to dead, because
the dpc thread could have just set it to online and is in the
middle of resetting it up.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Cc: David Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 31 Jan 2008 19:36:46 +0000 (13:36 -0600)]
[SCSI] iscsi class: add session scanning
This just adds iscsi session scanning which works like fc rport scanning.
The future patches will hook the drivers into Mathew Wilcox's async
scanning infrastructure, so userspace does not have to special case
iscsi and so userspace does not have to make a extra special case for
hardware iscsi root scanning.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 31 Jan 2008 19:36:45 +0000 (13:36 -0600)]
[SCSI] qla4xxx: use iscsi class session state check ready
This has qla4xxx use the iscsi class's check ready function
in the queue command function, so all iscsi drivers return the
same error value for common problems.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Cc: David Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Qla4xxx can just call the iscsi recovery functions directly.
There is no need for userspace to do this for qla4xxx, because
we do not use the mutex to iterate over devices anymore and iscsi_block
/unblock_session can be called from interrupt context or the dpc thread.
And having userspace do this just creates uneeded headaches for qla4xxx root
situations where the session may experience problems. For example
during the kernel shutdown the scsi layer wants to send sync caches, but at
this time userspace is not up (iscsid is not running), so we cannot
recover from the problem.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Cc: David Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[SCSI] arm: convert to accessors and !use_sg cleanup
- convert to accessors and !use_sg cleanup
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Tested-by: Russell King <rmk@arm.linux.org.uk> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tony Battersby [Tue, 6 Nov 2007 21:07:04 +0000 (16:07 -0500)]
[SCSI] sym53c8xx: fix resid calculation
This patch fixes the calculation of the data transfer residual for the
case of a command that is supposed to transfer an odd number of bytes on
a wide bus but transfers nothing instead.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Cc: Matthew Wilcox <matthew@wil.cx> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Aegis Lin [Fri, 1 Feb 2008 16:35:13 +0000 (17:35 +0100)]
[SCSI] ps3rom: sector size should be 512 bytes
It should be desired that 64 KiB is available for ATAPI transferrring.
(Historically) in SCSI/block layer sector size is defined as 512 during
sector-byte calculation.
Originally in ps3rom.c CD_FRAMESIZE (2048) was used, which limited
/sys/block/sr0/queue/max_sectors_kb to 16 KiB (32 sectors).
Signed-off-by: Aegis Lin <aegislin@gmail.com> Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Adrian Bunk [Mon, 28 Jan 2008 22:11:27 +0000 (00:11 +0200)]
[SCSI] libiscsi: make __iscsi_complete_pdu() static
__iscsi_complete_pdu() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Linus Torvalds [Thu, 7 Feb 2008 21:21:02 +0000 (13:21 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
BKL-removal: Implement a compat_ioctl handler for JFS
BKL-removal: Use unlocked_ioctl for jfs
Jesse Barnes [Thu, 7 Feb 2008 19:15:20 +0000 (11:15 -0800)]
i915: Fix GR register array size off-by-one bug
Make sure we have enough room for all the GR registers or we'll end up
clobbering the AR index register (which should actually be harmless
unless the BIOS is making an assumption about it).
Andi Kleen [Sun, 27 Jan 2008 22:58:51 +0000 (16:58 -0600)]
BKL-removal: Use unlocked_ioctl for jfs
Convert jfs_ioctl over to not use the BKL. The only potential race
I could see was with two ioctls in parallel changing the flags
and losing the updates. Use the i_mutex to protect against this.
Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
It's possible that the caller of sysfs_remove_group messed up and passed in an attribute group that was not really registered to this kobject. But don't panic for such a foolish error, spit out a warning about what happened, and continue on our way safely.
The original patch breaks BIOS updates on all Dell machines. The path to
the firmware file for the dell_rbu driver changes, which breaks all of
the userspace tools which rely on it.
Note that this patch re-introduces a problem with i2c name collision
that was previously fixed by this patch.
Signed-off-by: Michael E Brown <michael_e_brown@dell.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "whole_disk" attribute was not properly converted in the block
device conversion earlier, and if the file is read, bad things can
happen. This patch fixes this, making the attribute an empty one,
preserving the original functionality.
Many thanks to David Miller for finding this, and pointing me in the
proper place within the block code to look.
Acked-by: David S. Miller <davem@davemloft.net> Cc: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC32]: Use regsets in arch_ptrace().
[SPARC64]: Use regsets in arch_ptrace().
[SPARC32]: Use regsets for ELF core dumping.
[SPARC64]: Use regsets for ELF core dumping.
[SPARC64]: Remove unintentional ptrace debugging messages.
[SPARC]: Move over to arch_ptrace().
[SPARC]: Remove PTRACE_SUN* handling.
[SPARC]: Kill DEBUG_PTRACE code.
[SPARC32]: Add user regset support.
[SPARC64]: Add user regsets.
[SPARC64]: Fix booting on non-zero cpu.
Linus Torvalds [Thu, 7 Feb 2008 18:20:31 +0000 (10:20 -0800)]
Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6: (120 commits)
[MTD] Fix mtdoops.c compilation
[MTD] [NOR] fix startup lock when using multiple nor flash chips
[MTD] [DOC200x] eccbuf is statically defined and always evaluate to true
[MTD] Fix maps/physmap.c compilation with CONFIG_PM
[MTD] onenand: Add panic_write function to the onenand driver
[MTD] mtdoops: Use the panic_write function when present
[MTD] Add mtd panic_write function pointer
[MTD] [NAND] Freescale enhanced Local Bus Controller FCM NAND support.
[MTD] physmap.c: Add support for multiple resources
[MTD] [NAND] Fix misparenthesization introduced by commit 78b65179...
[MTD] [NAND] Fix Blackfin NFC ECC calculating bug with page size 512 bytes
[MTD] [NAND] Remove wrong operation in PM function of the BF54x NFC driver
[MTD] [NAND] Remove unused variable in plat_nand_remove
[MTD] Unlocking all Intel flash that is locked on power up.
[MTD] [NAND] at91_nand: Make mtdparts option can override board info
[MTD] mtdoops: Various minor cleanups
[MTD] mtdoops: Ensure sequential write to the buffer
[MTD] mtdoops: Perform write operations in a workqueue
[MTD] mtdoops: Add further error return code checking
[MTD] [NOR] Test devtype, not definition in flash_probe(), drivers/mtd/devices/lart.c
...
Linus Torvalds [Thu, 7 Feb 2008 17:45:14 +0000 (09:45 -0800)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Add HP Jornada 6xx driver
leds: Remove the now uneeded ixp4xx driver
leds: Add power LED to the wrap driver
leds: Fix led-gpio active_low default brightness
leds: hw acceleration for Clevo mail LED driver
leds: Add support for hardware accelerated LED flashing
leds: Standardise LED naming scheme
leds: Add clevo notebook LED driver
The recently introduced page walker (walk_page_range()) calls pgd_offset with a
const struct mm_struct pointer, causing the following compile warning on m68k:
mm/pagewalk.c:111: warning: passing argument 1 of 'pgd_offset' discards qualifiers from pointer target type
Make the `mm' parameter of the inline function pgd_offset() const to shut it
up.
Linus Torvalds [Thu, 7 Feb 2008 17:07:16 +0000 (09:07 -0800)]
Merge branch 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (22 commits)
drm: add initial r500 drm support
radeon: setup the ring buffer fetcher to be less agressive.
drm: fixup some of the ioctl function exit paths
drm: the drm really should call pci_set_master..
i915: Add chipset id for Intel Integrated Graphics Device
drm: cleanup DRM_DEBUG() parameters
drm/i915: add support for E7221 chipset
drm: don't cast a pointer to pointer of list_head
mga_dma: return 'err' not just zero from mga_do_cleanup_dma()
drm: add _DRM_DRIVER flag, and re-order unload.
drm: enable udev node creation
drm: Make DRM_IOCTL_GET_CLIENT return EINVAL when it can't find client #idx.
drm: move drm_mem_init to proper place in startup sequence
drm: call driver load function after initialising AGP
drm: Fix ioc32 compat layer
drm: fd.o bug #11895: Only add the AGP base to map offset if the caller didn't.
i915: add suspend/resume support
drm: update DRM sysfs support
drm: Initialize the AGP structure's base address at init rather than enable.
drm: move two function extern into the correct block
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Add missing printk levels to e_powersaver
[CPUFREQ] Fix sparse warning in powernow-k8
[CPUFREQ] Support Model D parts and newer in e_powersaver
[CPUFREQ] Powernow-k8: Update to support the latest Turion processors
[CPUFREQ] fix configuration help message
[CPUFREQ] powernow-k8 print pstate instead of fid/did for family 10h
[CPUFREQ] Eliminate cpufreq_userspace scaling_setspeed deadlock
[CPUFREQ] gx-suspmod.c: use boot_cpu_data instead of current_cpu_data
[CPUFREQ] fix incorrect comment on show_available_freqs() in freq_table.c
[CPUFREQ] drivers/cpufreq: Add missing "space"
[CPUFREQ] arch/x86: Add missing "space"
[CPUFREQ] Remove pointless Kconfig dependancy
Jiri Slaby [Thu, 7 Feb 2008 08:16:45 +0000 (00:16 -0800)]
Char: mxser, ioctl cleanup
- remove dead MOXA_GET_CONF (always returned -ENXIO)
- remove useless MOXA_GET_CUMAJOR (unused)
- use get/put_user instead of copy_from/to_user for simple types
- cleanup TIOCMIWAIT -- return -ERESTARTSYS on signal, move condition into
separate function
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Reviewed-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 7 Feb 2008 08:16:42 +0000 (00:16 -0800)]
Char: mxser, remove special baudrate processing
Let the special baudrate processing on the tty layer. Also remove
set/get_special_rate ioctls introduced in commit f64c84a1668930d1ca2b7dbaa92146c2139cb508, since it is no longer needed.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Reviewed-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 7 Feb 2008 08:16:40 +0000 (00:16 -0800)]
Char: serial167, remove bottomhalf
- Cy_EVENT_OPEN_WAKEUP is simple wake_up
- Cy_EVENT_HANGUP is wake_up + tty_hangup, which schedules its own work
- Cy_EVENT_WRITE_WAKEUP is tty_wakeup which may be called directly too
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 7 Feb 2008 08:16:39 +0000 (00:16 -0800)]
Char: stallion, remove bottomhalf
- tty_hangup schedules a bottomhalf itself, tty_wakeup doesn't need it
- call the CD code (part of work handler previously) directly from the code
(it wakes somebody up or calls tty_hangup at worse)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 7 Feb 2008 08:16:36 +0000 (00:16 -0800)]
Char: stallion, fix compiler warnings
Don't emit warnings on 64 bit platforms from min(). sizeof() on those
is not uint, neither 2 pointers difference, cast it to uint by min_t in
both cases.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Slaby [Thu, 7 Feb 2008 08:16:33 +0000 (00:16 -0800)]
Char: rocket, printk cleanup
- add KERN_ level to each print
- change some levels appropriately
- add \n at the ends where missing
- change two complex printks into dev_info, where the original info is
printed automatically
Signed-off-by: Jiri Slaby <jirislaby@gmail.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Frank Sorenson [Thu, 7 Feb 2008 08:16:31 +0000 (00:16 -0800)]
i8k: Inspiron E1705 fix
Needs the following in order to work correctly on my Inspiron E1705:
Add DMI Product name to i8k for Dell MP061 hardware (Inspiron 9400/E1705)
Signed-off-by: Frank Sorenson <frank@tuxrocks.com> Cc: Bradley Smith <bradjsmith@btinternet.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bradley Smith [Thu, 7 Feb 2008 08:16:30 +0000 (00:16 -0800)]
I8K: add i8k driver to the x86_64 Kconfig
Adds i8k driver to the x86_64 Kconfig.
Signed-off-by: Bradley Smith <bradjsmith@btinternet.com> Cc: Frank Sorenson <frank@tuxrocks.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bradley Smith [Thu, 7 Feb 2008 08:16:27 +0000 (00:16 -0800)]
I8K: allow i8k driver to be built on x86_64 systems
Adds #if clause and additional inline assembly so that the driver
builds on x86_64 systems.
Signed-off-by: Bradley Smith <bradjsmith@btinternet.com> Cc: Frank Sorenson <frank@tuxrocks.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add cmpxchg_local to sparc, move __cmpxchg to system.h
Move cmpxchg and add cmpxchg_local to system.h.
Use the new generic cmpxchg_local (disables interrupt).
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: William Lee Irwin III <wli@holomorphy.com> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gunnar Larisch [Thu, 7 Feb 2008 08:16:22 +0000 (00:16 -0800)]
Add cmpxchg_local to ppc
Add a local processor version of cmpxchg for ppc.
Implements __cmpxchg_u32_local and uses it for 32 bits cmpxchg_local.
It uses the non NMI safe cmpxchg_local_generic for 1, 2 and 8 bytes
cmpxchg_local.
Signed-off-by: Gunnar Larisch <gl@denx.de> Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: Paul Mackerras <paulus@samba.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Kumar Gala <galak@gate.crashing.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
projects / linux-2.6 / log