Divy Le Ray [Wed, 22 Aug 2007 03:49:21 +0000 (20:49 -0700)]
cxgb3 - Expose HW memory page info
A HW issue requires limiting the receive window size
to 23 pages of internal memory.
These pages can be configured to different sizes,
thus the RDMA driver needs to know the
page size to enforce the upper limit.
Also assign explicit enum values.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Divy Le Ray [Wed, 22 Aug 2007 03:49:15 +0000 (20:49 -0700)]
cxgb3 - use immediate data for offload Tx
Send small TX_DATA work requests as immediate data even when
there are fragments. this avoids doing multiple DMAs for
small fragmented packets.
The driver already implements this optimization for small
contiguous packets.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Divy Le Ray [Wed, 22 Aug 2007 03:49:05 +0000 (20:49 -0700)]
cxgb3 - Update rx coalescing length
Reduce Rx coalescing length to 12288
Large bursts from the adapter to the host create back pressure
on the chip. Reducing the burst size avoids the issue.
Signed-off-by: Divy Le Ray <divy@chelsio.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Brian King [Fri, 17 Aug 2007 14:16:49 +0000 (09:16 -0500)]
ibmveth: Remove dead frag processing code
Removes dead frag processing code from ibmveth. Since NETIF_F_SG was
not set, this code was never executed. Also, since the ibmveth
interface can only handle 6 fragments, core networking code would need
to be modified in order to efficiently enable this support.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Brian King [Sat, 15 Sep 2007 20:36:07 +0000 (13:36 -0700)]
ibmveth: Enable TCP checksum offload
This patchset enables TCP checksum offload support for IPV4
on ibmveth. This completely eliminates the generation and checking of
the checksum for packets that are completely virtual and never
touch a physical network. A simple TCP_STREAM netperf run on
a virtual network with maximum mtu set yielded a ~30% increase
in throughput. This feature is enabled by default on systems that
support it, but can be disabled with a module option.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
uli526x: Add suspend and resume routines (updated)
Add suspend/resume support to the uli526x network driver (tested on x86_64,
with 'Ethernet controller: ALi Corporation M5263 Ethernet Controller, rev 40').
This patch is based on the suspend/resume code in the tg3 driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)
This driver implements support for the ICH9 on-board LAN ethernet
device. The device is similar to ICH8.
The driver encompasses code to support 82571/2/3, es2lan and ICH8
devices as well, but those device IDs are disabled and will be
"lifted" from the e1000 driver over one at a time once this driver
receives some more live time.
Changes to the last snapshot posted are exclusively in the internal
hardware API organization. Many thanks to Jeff Garzik for jumping in
and getting this organized with a keen eye on the future layout.
[ Integrated napi_struct patch from Auke as well... -DaveM ]
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Morton [Tue, 21 Aug 2007 09:15:45 +0000 (02:15 -0700)]
[PATCH] libertas: printk warning fixes
drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_helper':
drivers/net/wireless/libertas/if_cs.c:462: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_real':
drivers/net/wireless/libertas/if_cs.c:538: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Brajesh Dave [Mon, 20 Aug 2007 17:09:13 +0000 (13:09 -0400)]
[PATCH] libertas: advertise 11g ad-hoc rates
Advertise support for 802.11g bitrates when starting adhoc
networks, not just 802.11b bitrates.
Signed-off-by: Brajesh Dave <brajeshd@marvell.com> Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marek Vašut [Mon, 20 Aug 2007 16:55:41 +0000 (12:55 -0400)]
[PATCH] libertas: region code values specified as 8bit
This patch strips away possible mess in regioncode (eg. on my card - 88W8305
chipset - I get 0x3031 instead of expected 0x0031 and as a result the driver
defaults to USA region which is obviously incorrect). Following patch fixes
the issue.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Mon, 20 Aug 2007 16:22:15 +0000 (12:22 -0400)]
[PATCH] libertas: send reset command directly instead of calling libertas_reset_device
Ensures that any platform specific code that might live in libertas_reset_device
(for example, OLPC tells the EC to do a GPIO-toggled reset of the wireless
from libertas_reset_device) isn't called. Could be handled better by
interface-specific callbacks and a flag for "other hardware reset".
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Marcelo Tosatti <marcelo@kvack.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Mon, 20 Aug 2007 15:43:25 +0000 (11:43 -0400)]
[PATCH] libertas: reorganize and simplify init sequence
This patch moves all firmware load responsibility into the interface-specific
code and gets rid of the firmware pointer in the generic card structure. It
also removes 3 fairly unecessary callbacks: hw_register_dev, hw_unregister_dev,
and hw_prog_firmware. It also makes the init sequence from interface
probe functions more logical, as there are paired add/remove and start/stop
calls into generic libertas code.
Because the USB driver code uses the same TX URB callback for both firmware
upload (where the generic libertas structure isn't initialized yet) and for
normal operation (where it is), some bits of USB code have to deal with
'priv' being NULL. All USB firmware upload bits have been changed to not
require 'priv' at all, but simply the USB card structure.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Mon, 6 Aug 2007 01:25:18 +0000 (02:25 +0100)]
[PATCH] zd1211rw: Add ID for ZyXEL M-202 XtremeMIMO
Tested by Nathen Meyers
FCC ID: SI5WUB221Z
zd1211b chip 0586:340a v4810 high 00-13-49 AL2230_RF pa0 ----S
Despite the product name, I'm pretty sure this isn't a MIMO device. It
appears just to be a normal ZD1211B and we have never heard of these
devices having more than 1 RF. I guess they named this product this way
to make it appear that it fits in with the rest of their XtremeMIMO
product range.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ulrich Kunitz [Mon, 6 Aug 2007 00:24:31 +0000 (01:24 +0100)]
[PATCH] zd1211rw: consistent handling of ZD1211 specific rates
As pointed out by Daniel Drake, the zd1211rw driver used several
different rate values and names throughout the driver. He has
written a patch to change it and tweaked it after some pretty wild
ideas from my side. But the discussion helped me to understand the
problem better and I think I have nailed it down with this patch.
A zd-rate will consist from now on of a four-bit "pure" rate value
and a modulation type flag as used in the ZD1211 control set used
for packet transmission. This is consistent with the usage in the
zd_rates table. If possible these zd-rates should be used in the
code.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de> Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ulrich Kunitz [Mon, 6 Aug 2007 00:23:54 +0000 (01:23 +0100)]
[PATCH] zd1211rw: removed noisy debug messages
While developing the driver we added a lot of debug messages for
setting hardware registers. These messages make the reading of the
log files difficult and are of no use anymore. This patch removes
those messages in zd_chip.c.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de> Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes some residual dead code left over from removing the
"flip" receive mode. This patch doesn't change the generated output
at all, since gcc already realized it was dead.
This resolves the "regression" reported by Adrian.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com> Cc: Adrian Bunk <bunk@stusta.de> Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
dev = alloc_*dev(...
...
priv = netdev_priv(dev);
memset(priv, 0, sizeof(*priv));
The memset() here is superfluous. alloc_netdev() uses kzalloc()
to allocate needed memory so there is no need to zero the priv region
twice.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
- Calling store_xmsi_data to store the MSI-X datas during initialization
in s2io-init_nic function
- Disabling NAPI when MSI-X is enabled
- Freeing sp->entries and sp->s2io_entries in s2io_rem_isr
- Making MSIX as default intr_type
- Driver will test MSI-X by issuing test MSI-X vector and if fails it will
fallback to INTA
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com> Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com> Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: David S. Miller <davem@davemloft.net>
dev->priv to netdev_priv(dev), drivers/net/tokenring/
Replacing accesses to dev->priv to netdev_priv(dev). The replacment
is safe when netdev_priv is used to access a private structure that is
right next to the net_device structure in memory.
Cf http://groups.google.com/group/comp.os.linux.development.system/browse_thread/thread/de19321bcd94dbb8/0d74a4adcd6177bd
This is the case when the net_device structure was allocated with
a call to alloc_netdev or one of its derivative.
Here is an excerpt of the semantic patch that performs the transformation
@ rule2 depends on rule1 && !rule1bis @
struct net_device *dev;
type rule1.T;
@@
- (T*) dev->priv
+ netdev_priv(dev)
PS: I have performed the same transformation on the whole kernel
and it affects around 70 files, most of them in drivers/net/.
Should I split my patch for each subnet directories ? (wireless/, wan/, etc)
Thanks to Thomas Surrel for helping me refining my semantic patch.
Jeff Garzik [Tue, 24 Jul 2007 05:30:36 +0000 (01:30 -0400)]
[netdrvr] skfp: remove a bunch of dead code
The driver has not compiled in anything except PCI support for many
years (see drivers/net/skfp/Makefile). This driver is also unmaintained
for many years, so arguments for keeping the cross-OS, cross-bus (ISA,
EISA, MCA) code do not exist.
Boot2 version used to be hardcoded in the uploaded firmware,
this patch preserves the boot2 version before uploading firmware
and sends it to the firmware again on resume.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Williams [Thu, 2 Aug 2007 17:19:04 +0000 (13:19 -0400)]
[PATCH] libertas: push WEXT scan requests to a work queue
Push WEXT scan requests to a workqueue and have each partial scan queue
the next part, then only report results when the complete scan has finished.
Full scans don't go through the work queue.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[PATCH] libertas: monitor mode support for OLPC firmware
Driver support for the monitor mode support that will be available in the next
OLPC 'bleeding edge' Marvell firmware release (most likely, 5.110.16.p2).
where mode is the hex mask that specifies which frames to sniff (in short, 0x1
for data, 0x2 for all management but beacons, 0x4 for beacons). Any non zero
mode will activate the monitor mode, inhibiting transmission in ethX and mshX
interfaces and routing all the incoming traffic to a new rtapX interface that
will output the packets in 802.11+radiotap headers format.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jean Tourrilhes [Thu, 2 Aug 2007 17:16:30 +0000 (13:16 -0400)]
[PATCH] libertas: fix a few wext abuses...
o SIOCGIWNAME is not designed to return the version number of the driver.
On the other hand, you are free to abuse SIOCGIWNICKN for that purpose.
o Don't attempt to fix the WE19/WE20 transition in the driver, because
your fixes are bogus, and redundant with the code in the kernel (you may
endup with +2, you can't read 32 char ESSID...).
o In SIOCSIWTXPOW, if you specified in iwrange that you want dBm, you
should only get dBm, which allow to reduce code bloat.
Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[PATCH] libertas: keep mesh autostart enabled while asleep
After loading the firmware, mesh autostart will be disabled. After that, the
user will still be able to enable or disable it at will. On suspend, it will be
always activated and later on resume it will go back to the state it had before
going to sleep.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[PATCH] libertas: revert CAPINFO_MASK to its original value
CAPINFO_MASK changed on commits 981f187b and a091095b. Reverting to the original
value. Also move CAPINFO_MASK into the sole user, join.c. CAPINFO_MASK
should be in host CPU byte order; capability is converted to device
byte order elsewhere.
This fixes OLPC ticket #2161
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This value was parsed out, but then nowhere used ... except in
some debugfs output. I can't imagine anyone wanting to use this
value for anything real (as no other driver exports it), so
bye-bye.
Along this, made the columns of
/sys/kernel/debug/libertas_wireless/*/getscantable align again.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Those two variables were initialized with some default values, but there
is no code that would ever change them. So we could use as well the defaults
directly.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Thu, 4 Oct 2007 00:25:41 +0000 (17:25 -0700)]
[PATCH] add support for Marvell 8385 CF cards
This patch adds support for Marvell based 8385 compact flash cards.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log