Thomas Gleixner [Sat, 23 Feb 2008 19:43:21 +0000 (20:43 +0100)]
x86: CPA: avoid split of alias mappings
avoid over-eager large page splitup.
When the target area needs to be split or is split already (ioremap)
then the current code enforces the split of large mappings in the alias
regions even if we could avoid it.
Use a separate variable processed in the cpa_data structure to carry
the number of pages which have been processed instead of reusing the
numpages variable. This keeps numpages intact and gives the alias code
a chance to keep large mappings intact.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Roland McGrath [Wed, 27 Feb 2008 19:42:15 +0000 (11:42 -0800)]
x86 vdso: fix build locale dependency
Priit Laes discovered that the sed command processing nm output was
sensitive to locale settings. This was addressed in commit 03994f01e8b72b3d01fd3d09d1cc7c9f421a727c by using [:alnum:] in place of
[a-zA-Z0-9].
But that solution too is locale-dependent and may not always match
the identifiers it needs to. The better fix is just to run sed et al
with a fixed locale setting in all builds.
Signed-off-by: Roland McGrath <roland@redhat.com> CC: Priit Laes <plaes@plaes.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Hans Rosenfeld [Mon, 18 Feb 2008 17:10:47 +0000 (18:10 +0100)]
x86: fix pmd_bad and pud_bad to support huge pages
I recently stumbled upon a problem in the support for huge pages. If a
program using huge pages does not explicitly unmap them, they remain
mapped (and therefore, are lost) after the program exits.
I observed that the free huge page count in /proc/meminfo decreased when
running my program, and it did not increase after the program exited.
After running the program a few times, no more huge pages could be
allocated.
The reason for this seems to be that the x86 pmd_bad and pud_bad
consider pmd/pud entries having the PSE bit set invalid. I think there
is nothing wrong with this bit being set, it just indicates that the
lowest level of translation has been reached. This bit has to be (and
is) checked after the basic validity of the entry has been checked, like
in this fragment from follow_page() in mm/memory.c:
if (pmd_none(*pmd) || unlikely(pmd_bad(*pmd)))
goto no_page_table;
Note that this code currently doesn't work as intended if the pmd refers
to a huge page, the pmd_huge() check can not be reached if the page is
huge.
Extending pmd_bad() (and, for future 1GB page support, pud_bad()) to
allow for the PSE bit being set fixes this. For similar reasons,
allowing the NX bit being set is necessary, too. I have seen huge pages
having the NX bit set in their pmd entry, which would cause the same
problem.
Signed-Off-By: Hans Rosenfeld <hans.rosenfeld@amd.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Roland McGrath [Tue, 26 Feb 2008 21:00:18 +0000 (13:00 -0800)]
x86: tls prevent_tail_call
Fix a kernel bug (vmware boot problem) reported by Tomasz Grobelny,
which occurs with certain .config variants and gccs.
The x86 TLS cleanup in commit efd1ca52d04d2f6df337a3332cee56cd60e6d4c4
made the sys_set_thread_area and sys_get_thread_area functions ripe for
tail call optimization. If the compiler chooses to use it for them, it
can clobber the user trap frame because these are asmlinkage functions.
Reported-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net> Signed-off-by: Roland McGrath <roland@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Fri, 29 Feb 2008 16:41:13 +0000 (08:41 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (35 commits)
Blackfin Serial Driver: Fix bug - Only insert UART rx char in timer task.
Blackfin Serial Driver: Fix bug - update tx dma buffer tail before wake up processes.
Blackfin Serial Driver: Fix bug - Increase buffer tail immediately before starting tx dma.
[Blackfin] serial driver: Add flow control support to bf54x
[Blackfin] serial driver: Fix bug Poll RTS/CTS status in DMA mode as well
[Blackfin] serial driver: ADSP-BF52x arch/mach support
[Blackfin] serial driver: use simpler comment headers and strip out information that is maintained in the scm's log
[Blackfin] serial driver: rework break flood anomaly handling to be more robust/realistic about what we can actually work around
[Blackfin] serial driver: fix bug - cache the bits of the LSR on systems where the LSR is read-to-clear
[Blackfin] serial driver: fix bug - should not wait for the TFI bit, just clear it when tx stop.
[Blackfin] serial driver: Fix bug serial driver in DMA mode spams history to console on shell restart
[Blackfin] serial driver: Fix bug Free rx dma buffer in shutdown.
[Blackfin] serial driver: Clean up UART DMA code.
Blackfin Serial driver: Fix bug - serial driver in PIO mode cant handle input very quickly
[Blackfin] arch: kill section mismatch warnings
[Blackfin] arch: handle the most common L1 shrinkage case (L1 does not exist for a part) so that any parts labeled for L1 instead get placed into external memory sections
[Blackfin] arch: add bfin_clear_PPIx_STATUS() helper funcs like we have for other parts
[Blackfin] arch: make sure we have proper description/copyright/license lines
[Blackfin] arch: Fix CONFIG_PM support for BF561
[Blackfin] arch: Remove DPMC char driver option
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
arch/sh/drivers/dma/dma-sh.c: Correct use of ! and &
serial: Move asm-sh/sci.h to linux/serial_sci.h.
sh: Fix up HAS_SR_RB typo in entry-macros.
maple: fix device detection
sh: fix rtc_resources setup for sh770x
sh: heartbeat: ioremap is expected to succeed
sh: Storage class should be before const qualifier
maple: remove unused variable
sh: SH5-103 needs to select CPU_SH5.
sh: Rename SH-3 CCR3 reg to avoid synclink_cs clash.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (79 commits)
[X25]: Use proc_create() to setup ->proc_fops first
[WANROUTER]: Use proc_create() to setup ->proc_fops first
[8021Q]: Use proc_create() to setup ->proc_fops first
[IPV4]: Use proc_create() to setup ->proc_fops first
[IPV6]: Use proc_create() to setup ->proc_fops first
[SCTP]: Use proc_create() to setup ->proc_fops first
[PKTGEN]: Use proc_create() to setup ->proc_fops first
[NEIGHBOUR]: Use proc_create() to setup ->proc_fops first
[LLC]: Use proc_create() to setup ->proc_fops first
[IPX]: Use proc_create() to setup ->proc_fops first
[SUNRPC]: Use proc_create() to setup ->proc_fops first
[ATM]: Use proc_create() to setup ->proc_fops first
[SCTP]: Update AUTH structures to match declarations in draft-16.
[SCTP]: Incorrect length was used in SCTP_*_AUTH_CHUNKS socket option
[SCTP]: Clean up naming conventions of sctp protocol/address family registration
[APPLETALK]: Use proc_create() to setup ->proc_fops first
[BNX2X]: add bnx2x to MAINTAINERS
[BNX2X]: update version, remove CVS strings
[BNX2X]: Fix Xmit bugs
[BNX2X]: Prevent PCI queue overflow
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Adjust kernel PC validation test in fault handler.
[SPARC64]: Loosen checks in exception table handling.
[SPARC64]: Fix section mismatch from kernel_map_range
[SPARC64]: Fix section mismatchs from dr_cpu_data
[SPARC]: Fix build in arch/sparc/kernel/led.c
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: remove stale comments from ide-dma.c (take 2)
ide: remove ide-tape documentation from Documentation/ide.txt
qd65xx: remove commented out code
ide-tape: schedule driver for removal after 6 months
ide-disk: add missing printk() KERN_* levels
ide: fix sparse warning about shadowing 'flags' symbol
ide-cd: fix CD/DVD burning
ide-cd: fix 'ireason' handling for REQ_TYPE_ATA_PC requests
qd65xx: fix setup of QD6580 Control register
ide: skip probing port if "hdx=noprobe" was used for both devices on it
ide: remove redundant comment from ide_unregister()
hpt366: fix section mismatch warnings
ide-cd: Enable audio play quirk for Optiarc DVD RW AD-5200A drive
David Howells [Thu, 28 Feb 2008 13:29:43 +0000 (13:29 +0000)]
Fix hpet_(un)register_irq_handler() for emulation
Fix hpet_(un)register_irq_handler() for when CONFIG_HPET_EMULATE_RTC=n. They
are provided macros that substitute value 0, but if they are called as
functions and the return value isn't checked, the following warnings appear:
drivers/char/rtc.c: In function `rtc_init':
drivers/char/rtc.c:1063: warning: statement with no effect
drivers/char/rtc.c: In function `rtc_exit':
drivers/char/rtc.c:1157: warning: statement with no effect
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Roland McGrath [Tue, 26 Feb 2008 21:20:58 +0000 (13:20 -0800)]
elfcore-compat fix uid/gid types
I overlooked the difference between __kernel_uid_t and uid_t when defining
struct compat_elf_prpsinfo. The result is a regression in 32-bit core
dumps on x86_64, where the NT_PRPSINFO note has the wrong size and layout.
This patch fixes it.
Harvey Harrison [Fri, 29 Feb 2008 10:46:32 +0000 (11:46 +0100)]
[ALSA] sound: ice1712: unused structs
Don't need to declare a struct when defining a structure layout. Both
of these structs are unused.
sound/pci/ice1712/revo.c:39:3: warning: symbol 'revo51' was not declared. Should it be static?
sound/pci/ice1712/phase.c:54:3: warning: symbol 'phase28' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 25 Feb 2008 14:32:01 +0000 (15:32 +0100)]
[ALSA] hda-codec - Fix AD1988 capture elements
The some indices of capture elements of AD1988 are wrongly assigned.
This patch fixes it. See ALSA bug#3795
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3795
Clemens Ladisch [Mon, 25 Feb 2008 10:01:00 +0000 (11:01 +0100)]
[ALSA] usb-audio: add workaround for broken E-Mu frequency feedback
Add a workaround for the feedback pipe of E-Mu 0202/0404 USB devices
that reports the number of samples per packet instead of the number of
samples per microframe.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 18 Feb 2008 11:36:11 +0000 (12:36 +0100)]
[ALSA] hda-codec - Fix Master volume on HP dv8000
HP dv8000 laptop has a problem with Master volume. It's due to the
connection of the widget 0x13. When it's connected from the analog
amp mixer (0x19), it works as expected mysteriously (ALSA bug#3775):
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3775
Vlad Yasevich [Wed, 27 Feb 2008 21:04:52 +0000 (16:04 -0500)]
[SCTP]: Update AUTH structures to match declarations in draft-16.
The new SCTP socket api (draft 16) updates the AUTH API structures.
We never exported these since we knew they would change.
Update the rest to match the draft.
Neil Horman [Fri, 15 Feb 2008 14:53:59 +0000 (09:53 -0500)]
[SCTP]: Clean up naming conventions of sctp protocol/address family registration
I noticed while looking into some odd behavior in sctp, that the variable
name sctp_pf_inet6_specific was used twice to represent two different
pieces of data (its both a structure name and a pointer to that type of
structure), which is confusing to say the least, and potentially dangerous
depending on the variable scope. This patch cleans that up, and makes the
protocol and address family registration names in SCTP more regular,
increasing readability.
Herbert Xu [Thu, 28 Feb 2008 19:23:17 +0000 (11:23 -0800)]
[IPCOMP]: Disable BH on output when using shared tfm
Because we use shared tfm objects in order to conserve memory,
(each tfm requires 128K of vmalloc memory), BH needs to be turned
off on output as that can occur in process context.
Previously this was done implicitly by the xfrm output code.
That was lost when it became lockless. So we need to add the
BH disabling to IPComp directly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Zaytsev [Sat, 23 Feb 2008 10:33:07 +0000 (13:33 +0300)]
Don't build bcm43xx if SSB is static and b43 PCI-SSB bridge is enabled.
This may happen e.g. when the ssb is statically enables by the b44 driver,
and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the
b43/b43legacy drivers are built statically.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexey Zaytsev [Sat, 23 Feb 2008 09:59:26 +0000 (12:59 +0300)]
Use a separate config option for the b43 pci to ssb bridge.
The bridge code was unnecessary enabled by the b44
driver, but it prevents the bcm43xx driver from
being loaded, as the bridge claims the same pci ids.
Now we enable the birdge only if the b43{legacy}
drivers are selected.
Signed-off-by: Alexey Zaytsev <alexey.zaytsev@gmail.com> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Roland Dreier [Tue, 26 Feb 2008 14:26:56 +0000 (15:26 +0100)]
libertas: Remove unused exports
The libertas driver exports a number of symbols with no in-tree users;
remove these unused exports. lbs_reset_device() is completely unused, with
no callers at all, so remove the function completely.
A couple of these unused exported symbols are static, which causes the
following build error on ia64 with gcc 4.2.3:
drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict
drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict
Signed-off-by: Roland Dreier <rolandd@cisco.com> Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 25 Feb 2008 22:15:13 +0000 (23:15 +0100)]
rt2x00: Fix rt2x00lib_reset_link_tuner()
rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.
Reorder the things that should be done during a
link tuner reset and during a link tuner start.
Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 25 Feb 2008 22:15:05 +0000 (23:15 +0100)]
rt2x00: Add link tuner safe RX toggle states
This adds 2 new states which both are used to toggle
the RX. These new states are required for usage
inside the link tuner thread, because the normal
RX toggling will stop the link tuner thread.
While it is possible that the link tuner thread itself
is the caller of the RX toggle (when using software
antenna diversity).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Mon, 25 Feb 2008 22:15:01 +0000 (23:15 +0100)]
rt2x00: Fix antenna diversity
Fix 2 issues in antenna diversity selection.
1) the following statement will always return true.
if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5)
It is cleaner to check if the absolute value is smaller then 5.
2) Only enable software diversity when default antenna setup
indicates support for it. Don't select it when the hardware
does not indicate support for it...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
| CC drivers/net/ps3_gelic_wireless.o
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops':
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data'
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers'
| make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1
| make[2]: *** [drivers/net] Error 2
| make[1]: *** [drivers] Error 2
| make[1]: *** Waiting for unfinished jobs....
| make: *** [sub-make] Error 2
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc> Acked-by: Masakazu Mokuno <mokuno@sm.sony.co.jp> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Masakazu Mokuno [Fri, 22 Feb 2008 07:45:26 +0000 (16:45 +0900)]
PS3: gelic: Link the wireless net_device structure to the corresponding device structure
Link the net_device structure of the wireless part to the
corresponding device structure.
Without this, the sysfs node for this net_device would not have
'device' link.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 20 Feb 2008 10:47:45 +0000 (11:47 +0100)]
rndis_wlan: fix sparse warnings
It is obviously wrong to use an enum in a little endian struct,
and those other enums should be declared differently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patrick McHardy [Wed, 27 Feb 2008 20:21:18 +0000 (12:21 -0800)]
[NETFILTER]: Fix NF_QUEUE_NR() parenthesis
Properly add parens around the macro argument. This is not needed by
the kernel but the macro is exported to userspace, so it shouldn't
make any assumptions.
Also use NF_VERDICT_BITS instead of NF_VERDICT_QBTIS for the left-shift
since thats whats logically correct.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 27 Feb 2008 20:07:47 +0000 (12:07 -0800)]
[NETFILTER]: nf_conntrack: fix smp_processor_id() in preemptible code warning
Since we're using RCU for the conntrack hash now, we need to avoid
getting preempted or interrupted by BHs while changing the stats.
Fixes warning reported by Tilman Schmidt <tilman@imap.cc> when using
preemptible RCU:
[ 48.180297] BUG: using smp_processor_id() in preemptible [00000000] code: ntpdate/3562
[ 48.180297] caller is __nf_conntrack_find+0x9b/0xeb [nf_conntrack]
[ 48.180297] Pid: 3562, comm: ntpdate Not tainted 2.6.25-rc2-mm1-testing #1
[ 48.180297] [<c02015b9>] debug_smp_processor_id+0x99/0xb0
[ 48.180297] [<fac643a7>] __nf_conntrack_find+0x9b/0xeb [nf_conntrack]
Tested-by: Tilman Schmidt <tilman@imap.cc> Tested-by: Christian Casteyde <casteyde.christian@free.fr> [Bugzilla #10097] Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Iff the parent has TIF_DEBUG set, _and_ clone_flags includes
CLONE_PTRACE we should set the TIF_DEBUG flag for the child and
increment the ocd refcount. Otherwise, the TIF_DEBUG flag must be
unset.
Currently, the child inherits TIF_DEBUG from the parent before
copy_thread is called, so TIF_DEBUG may be already be set before we
determine whether the child is supposed to inherit debugging
capabilities from the parent or not. This means that ocd_enable()
won't increment the refcount, because TIF_DEBUG is already set, and
that TIF_DEBUG will be set for processes that aren't being debugged.
This leads to a refcounting asymmetry, which may show up as
------------[ cut here ]------------
Badness at arch/avr32/kernel/ocd.c:73
PC is at ocd_disable+0x34/0x60
LR is at put_lock_stats+0xa/0x20
as reported by David Brownell. Happens when strace'ing a process that
forks a new child process, e.g. "strace mount -tjffs2 mtd1 /mnt", and
subsequently killing the child process (e.g. "umount /mnt".)
Pavel Emelyanov [Wed, 27 Feb 2008 07:51:04 +0000 (23:51 -0800)]
[INET]: Don't create tunnels with '%' in name.
Four tunnel drivers (ip_gre, ipip, ip6_tunnel and sit) can receive a
pre-defined name for a device from the userspace. Since these drivers
call the register_netdevice() (rtnl_lock, is held), which does _not_
generate the device's name, this name may contain a '%' character.
Not sure how bad is this to have a device with a '%' in its name, but
all the other places either use the register_netdev(), which call the
dev_alloc_name(), or explicitly call the dev_alloc_name() before
registering, i.e. do not allow for such names.
This had to be prior to the commit 34cc7b, but I forgot to number the
patches and this one got lost, sorry.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 27 Feb 2008 06:20:44 +0000 (22:20 -0800)]
[AF_KEY]: Fix oops by converting to proc_net_*().
To make sure the procfs visibility occurs after the ->proc_fs ops are
setup, use proc_net_fops_create() and proc_net_remove().
This also fixes an OOPS after module unload in that the name string
for remove was wrong, so it wouldn't actually be removed. That bug
was introduced by commit 61145aa1a12401ac71bcc450a58c773dd6e2bfb9
("[KEY]: Clean up proc files creation a bit.")
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjorn Mork [Wed, 27 Feb 2008 02:17:53 +0000 (18:17 -0800)]
[IPV4]: Reset scope when changing address
This bug did bite at least one user, who did have to resort to rebooting
the system after an "ifconfig eth0 127.0.0.1" typo.
Deleting the address and adding a new is a less intrusive workaround.
But I still beleive this is a bug that should be fixed. Some way or
another.
Another possibility would be to remove the scope mangling based on
address. This will always be incomplete (are 127/8 the only address
space with host scope requirements?)
We set the scope to RT_SCOPE_HOST if an IPv4 interface is configured
with a loopback address (127/8). The scope is never reset, and will
remain set to RT_SCOPE_HOST after changing the address. This patch
resets the scope if the address is changed again, to restore normal
functionality.
Signed-off-by: Bjorn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Thery [Wed, 27 Feb 2008 02:10:03 +0000 (18:10 -0800)]
[IPV6]: Add missing initializations of the new nl_info.nl_net field
Add some more missing initializations of the new nl_info.nl_net field
in IPv6 stack. This field will be used when network namespaces are
fully supported.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 27 Feb 2008 01:52:05 +0000 (17:52 -0800)]
[MACVLAN]: Update Kconfig to refer to iproute
Since the macvlan release I had at least 5 users asking how to configure
it since the old userspace tool doesn't work with the version in the
kernel. Add a pointer to the Kconfig help.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 26 Feb 2008 20:42:11 +0000 (21:42 +0100)]
arch/sh/drivers/dma/dma-sh.c: Correct use of ! and &
In commit e6bafba5b4765a5a252f1b8d31cbf6d2459da337, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
Faisal Latif [Thu, 21 Feb 2008 14:31:22 +0000 (08:31 -0600)]
RDMA/nes: Fix CRC endianness for RDMA connection establishment on big-endian
With commit ef19454b ("[LIB] crc32c: Keep intermediate crc state in
cpu order"), the behavior of crc32c changes on big-endian platforms.
Our algorithm expects the previous behavior; otherwise we have RDMA
connection establishment failure on big-endian platforms like powerpc.
Apply cpu_to_le32() to value returned by crc32c() to get the previous
behavior.
projects / linux-2.6 / log