V4L/DVB (8352): gspca: Buffers for USB exchanges cannot be in the stack.
gspca: Protect dq_callback() against simultaneous USB exchanges.
Temporary buffer for USB exchanges added in the device struct.
(all) Use a temporary buffer for all USB exchanges.
V4L/DVB (8350): gspca: Conform to v4l2 spec and mutex unlock fix.
gspca: Empty the application queues on streamoff ioctl.
streamon/off and qbuf ioctls may be done by any application.
Don't handle MJPEG pixel format as JPEG.
(thanks to Hans de Goede)
Authorize reqbufs ioctl when streaming.
Bad mutex unlock in poll() when streaming problem.
(thanks to Mauro Carvalho Chehab)
Don't handle 'webcam disconnected' in stream off.
Magnus Damm [Thu, 17 Jul 2008 02:02:08 +0000 (23:02 -0300)]
V4L/DVB (8343): soc_camera_platform: Add SoC Camera Platform driver
This patch adds a simple platform camera device. Useful for testing
cameras with SoC camera host drivers. Only one single pixel format
and resolution combination is supported.
Magnus Damm [Thu, 17 Jul 2008 01:59:28 +0000 (22:59 -0300)]
V4L/DVB (8342): sh_mobile_ceu_camera: Add SuperH Mobile CEU driver V3
This is V3 of the SuperH Mobile CEU soc_camera driver.
The CEU hardware block is configured in a transparent data fetch
mode, frames are captured from the attached camera and written to
physically contiguous memory buffers provided by the newly added
videobuf-dma-contig queue. Tested on sh7722 and sh7723 processors.
Changes since V2:
- remove SUPERH Kconfig dependency
- move sh_mobile_ceu.h to include/media
- add board callback support with enable_camera()/disable_camera()
- add support for declare_coherent_memory
- rework video memory limit
- more verbose error messages
Changes since V1:
- fixed the CEU driver to work with the newly updated patches
This is V3 of the physically contiguous videobuf queues patch.
Useful for hardware such as the SuperH Mobile CEU which doesn't
support scatter gatter bus mastering.
Since it may be difficult to allocate large chunks of physically
contiguous memory after some uptime due to fragmentation, this code
allocates memory using dma_alloc_coherent(). Architectures supporting
dma_declare_coherent_memory() can easily avoid fragmentation issues
by using dma_declare_coherent_memory() to force dma_alloc_coherent()
to allocate from a certain pre-allocated memory area.
Changes since V2
- use dma_handle for physical address
- use "scatter gather" instead of "scatter gatter"
Changes since V1:
- use dev_err() instead of pr_err()
- remember size in struct videobuf_dma_contig_memory
- keep struct videobuf_dma_contig_memory in .c file
- let videobuf_to_dma_contig() return dma_addr_t
- implement __videobuf_sync()
- return statements, white space and other minor fixes
Magnus Damm [Fri, 11 Jul 2008 23:59:34 +0000 (20:59 -0300)]
V4L/DVB (8338): soc_camera: Move spinlocks
This patch moves the spinlock handling from soc_camera.c to the actual
camera host driver. The spinlock_alloc/free callbacks are replaced with
code in init_videobuf(). So far all camera host drivers implement their
own spinlock_alloc/free methods anyway, and videobuf_queue_core_init()
BUGs on a NULL spinlock argument, so, new camera host drivers will not
forget to provide a spinlock when initialising their videobuf queues.
Paulius Zaleckas [Fri, 11 Jul 2008 23:50:31 +0000 (20:50 -0300)]
V4L/DVB (8337): soc_camera: make videobuf independent
Makes SoC camera videobuf independent. Includes all necessary changes for
PXA camera driver (currently the only driver using soc_camera in the mainline).
These changes are important for the future soc_camera based drivers.
Andy Walls [Sun, 13 Jul 2008 22:30:15 +0000 (19:30 -0300)]
V4L/DVB (8332): cx18: Suport external reset of the Z8F0811 IR controller on HVR-1600 for lirc
cx18: added in cx18_ir_reset_gpio function for lirc_pvr150 like module. Also
added the ability to reset the IR chip via ioctl like ivtv. This needs the
mutex to protect gpio_dir and gpio_val in struct cx18 as gpio changes can
come from a few different asynchronous sources now.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hermann Pitton [Sat, 12 Jul 2008 15:27:59 +0000 (12:27 -0300)]
V4L/DVB (8319): saa7134: Add support for analog only ASUSTeK P7131
saa7134: add a separate entry for the ASUSTeK P7131 analog only
and do some eeprom detection to escape from the TVFM7135
with the same PCI subsystem on auto detection.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For VIDIOC_G_FMT/VIDIOC_TRY_FMT, the V4L2 API spec states:
"Drivers should not return an error code unless the input is ambiguous"
"Very simple, inflexible devices may even ignore all input and always
return the default parameters."
"When the requested buffer type is not supported drivers return an
EINVAL error code."
i.e. returning errors for unsupported fields is bad, and it's ok to
unconditionally overwrite user-requested settings
This patch makes ov7670 meet that behaviour, and brings it in line with
other drivers e.g. stk-webcam. It also fixes compatibility with (unpatched)
gstreamer.
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Jonathan Corbet <corbet@lwn.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fixes some coding style issues.
It also fixes a NULL de-reference on driver unload.
The permissions for the module parameters were changed to 0644.
Signed-off-by: Dean Anderson <dean@sensoray.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Tue, 1 Jul 2008 07:35:26 +0000 (04:35 -0300)]
V4L/DVB (8311): sms1xxx: support device-specific firmware filenames on stellar usb1 sticks
Add the capability to define device-specific firmware filenames for the SMS1010,
with a mechanism to fall back to the generic firmware if the device-specific
firmware is not present.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 29 Jun 2008 17:45:37 +0000 (14:45 -0300)]
V4L/DVB (8309): sms1xxx: fix OOPS on 64 bit kernels due to a bad cast
Fix the following build warning:
smscoreapi.c: In function 'smscore_detect_mode':
smscoreapi.c:689: warning: cast from pointer to integer of different size
smscoreapi.c:689: warning: cast to pointer from integer of different size
smscoreapi.c: In function 'smscore_set_device_mode':
smscoreapi.c:820: warning: cast from pointer to integer of different size
smscoreapi.c:820: warning: cast to pointer from integer of different size
Michael Krufky [Sat, 28 Jun 2008 23:53:45 +0000 (20:53 -0300)]
V4L/DVB (8305): sms1xxx: fix warning: format '%d' expects type 'int', but argument x has type 'size_t'
Fix the following 64bit build warning:
make[2]: Entering directory `/usr/src/linux-headers-2.6.24-16-generic'
CC [M] smscoreapi.o
smscoreapi.c: In function 'smscore_load_firmware_from_file':
smscoreapi.c:604: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
CC [M] smsusb.o
smsusb.c: In function 'smsusb1_load_firmware':
smsusb.c:216: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
smsusb.c:223: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Thu, 26 Jun 2008 07:58:30 +0000 (04:58 -0300)]
V4L/DVB (8301): sms1xxx: add capability to define device-specific firmware filenames
Add the capability to define device-specific firmware filenames for the SMS1150,
with a mechanism to fall back to the generic firmware if the device-specific
firmware is not present.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (8257): uvcvideo: Fix possible AB-BA deadlock with videodev_lock and open_mutex
The uvcvideo driver's uvc_v4l2_open() method is called from videodev's
video_open() function, which means it is called with the videodev_lock
mutex held. uvc_v4l2_open() then takes uvc_driver.open_mutex to check
dev->state and avoid racing against a device disconnect, which means
that open_mutex must nest inside videodev_lock.
However uvc_disconnect() takes the open_mutex around setting
dev->state and also around putting its device reference. However, if
uvc_disconnect() ends up dropping the last reference, it will call
uvc_delete(), which calls into the videodev code to unregister its
device, and this will end up taking videodev_lock. This opens a
(unlikely in practice) window for an AB-BA deadlock and also causes a
lockdep warning because of the lock misordering.
Fortunately there is no apparent reason to hold open_mutex when doing
kref_put() in uvc_disconnect(): if uvc_v4l2_open() runs before the
state is set to UVC_DEV_DISCONNECTED, then it will take another
reference to the device and kref_put() won't call uvc_delete; if
uvc_v4l2_open() runs after the state is set, it will run before
uvc_delete(), see the state, and return immediately -- uvc_delete()
does uvc_unregister_video() (and hence video_unregister_device(),
which is synchronized with videodev_lock) as its first thing, so there
is no risk of use-after-free in uvc_v4l2_open().
Bug diagnosed based on a lockdep warning reported by Romano Giannetti
<romano@dea.icai.upcomillas.es>.
Andrew Morton [Fri, 4 Jul 2008 09:33:23 +0000 (06:33 -0300)]
V4L/DVB (8256): uvc/uvc_v4l2.c: suppress uninitialized var warning
drivers/media/video/uvc/uvc_v4l2.c: In function `uvc_v4l2_mmap':
drivers/media/video/uvc/uvc_v4l2.c:1035: warning: 'buffer' might be used uninitialized in this function
/home/v4l/master/v4l/gspca.c: In function 'gspca_frame_add':
/home/v4l/master/v4l/gspca.c:222: warning: format '%d' expects type 'int', but argument 2 has type 'long int'
/home/v4l/master/v4l/gspca.c: In function 'dev_read':
/home/v4l/master/v4l/gspca.c:1568: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'
/home/v4l/master/v4l/gspca.c:1618: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
Jean Delvare [Thu, 10 Jul 2008 14:23:37 +0000 (11:23 -0300)]
V4L/DVB (8246): tvaudio: Stop I2C driver ID abuse
The tvaudio driver is using "official" I2C device IDs for internal
purpose. There must be some historical reason behind this but anyway,
it shouldn't do that. As the stored values are never used, the easiest
way to fix the problem is simply to remove them altogether.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jean Delvare [Thu, 10 Jul 2008 14:04:10 +0000 (11:04 -0300)]
V4L/DVB (8245): ovcamchip: Delete stray I2C bus ID
I2C_HW_SMBUS_OVFX2 is referenced in ovcamchip_core.c, but no bus uses
this driver ID, so we can remove the reference. As far as I can see,
the Cypress FX2 webcam is handled by a different driver (dvb-usb).
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (8234): uvcvideo: Make input device support optional
UVC devices can report button events. The uvcvideo driver depends on
CONFIG_INPUT to report events to the input layer. This patch removes the hard
dependency by introducing a new CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV option.
V4L/DVB (8231): gspca: Do not declare the webcams declared by other drivers.
etoms: Do not declare the webcams declared by the driver et61x251.
sonixb, sonixj:
Do not declare the webcams declared by the driver sn9c102.
zc3xx: Do not declare the webcams declared by the driver zc0301.
projects / linux-2.6 / log