wait_for_completion(&startup_done)
// waits for complete() from B,
// ->state == TASK_UNINTERRUPTIBLE
We can't wake up 'B' in any way:
SIGCONT will be ignored because handle_stop_signal() sees
->signal->flags & SIGNAL_GROUP_EXIT.
sys_kill(SIGKILL)->__group_complete_signal() will choose
uninterruptible 'A', so it can't help.
sys_tkill(B, SIGKILL) will be ignored by specific_send_sig_info()
because B already has pending SIGKILL.
This scenario is not possbile if 'A' does do_group_exit(), because
it sets sig->flags = SIGNAL_GROUP_EXIT and delivers SIGKILL to
subthreads atomically, holding both tasklist_lock and sighand->lock.
That means that do_signal_stop() will notice !SIGNAL_STOP_DEQUEUED
after re-locking ->sighand. And it is not possible to any other
thread to re-add SIGNAL_STOP_DEQUEUED later, because dequeue_signal()
can only return SIGKILL.
I think it is better to change do_coredump() to do sigaddset(SIGKILL)
and signal_wake_up() under sighand->lock, but this patch is much
simpler.
Bryan Sutula [Wed, 5 Oct 2005 17:02:06 +0000 (11:02 -0600)]
[IA64] Avoid kernel hang during CMC interrupt storm
I've noticed a kernel hang during a storm of CMC interrupts, which was
tracked down to the continual execution of the interrupt handler.
There's code in the CMC handler that's supposed to disable CMC
interrupts and switch to polling mode when it sees a bunch of CMCs.
Because disabling CMCs across all CPUs isn't safe in interrupt context,
the disable is done with a schedule_work(). But with continual CMC
interrupts, the schedule_work() never gets executed.
The following patch immediately disables CMC interrupts for the current
CPU. This then allows (at least) one CPU to ignore CMC interrupts,
execute the schedule_work() code, and disable CMC interrupts on the rest
of the CPUs.
Acked-by: Keith Owens <kaos@sgi.com> Signed-off-by: Bryan Sutula <Bryan.Sutula@hp.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Russell King [Thu, 6 Oct 2005 12:09:42 +0000 (13:09 +0100)]
[MFD] Fix gcc4 build errors in ucb1x00-core.c
drivers/mfd/ucb1x00-core.c:555: error: static declaration of 'ucb1x00_class' follows non-static declaration
drivers/mfd/ucb1x00.h:109: error: previous declaration of 'ucb1x00_class' was here
Since ucb1x00_class isn't used by anything, remove the extern
declaration and the symbol export.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
David S. Miller [Wed, 5 Oct 2005 22:12:00 +0000 (15:12 -0700)]
[SPARC64]: Fix initrd when net booting.
By allocating early memory for the firmware page tables, we
can write over the beginning of the initrd image.
So what we do now is:
1) Read in firmware translations table while still on the
firmware's trap table.
2) Switch to Linux trap table.
3) Init bootmem.
4) Build firmware page tables using __alloc_bootmem().
And this keeps the initrd from being clobbered.
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Habets [Wed, 5 Oct 2005 19:21:36 +0000 (12:21 -0700)]
[SPARC]: Remove some duplicated sparc32 config items
Remove some duplicated items due to the inclusion of the general
drivers/Kconfig file. These are now taken from drivers/char/Kconfig,
and can be turned off there as well (which is desirable sometimes).
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Ralf Baechle [Wed, 5 Oct 2005 19:16:04 +0000 (12:16 -0700)]
[AX.25]: Fix packet socket crash
Since changeset 98a82febb6340466824c3a453738d4fbd05db81a AX.25 is passing
received IP and ARP packets to the stack through netif_rx() but we don't
set the skb->mac.raw to right value which may result in a crash with
applications that use a packet socket.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Timer set up by pneigh_enqueue() ended up calling ndisc_rcv()
via pndisc_redo(), which clears LOCALLY_ENQUEUED flag in
NEIGH_CB(skb) and NS was queued again.
Let's call ndisc_recv_ns() directly to avoid the loop.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Yan Zheng [Wed, 5 Oct 2005 19:08:13 +0000 (12:08 -0700)]
[MCAST] ipv6: Fix address size in grec_size
Signed-Off-By: Yan Zheng <yanzheng@21cn.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Acked-by: David L Stevens <dlstevens@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH] ppc: Fix timekeeping with HZ=250 on some Mac models
Older Macs which uses the VIA chip timers to calibrate the timebase used
some code that wouldn't work if HZ wasn't divisible by 100...
This fixes it at least for 250. Not totally perfect but should be
enough for now (so it at least works with the default value which is now
250).
There is still a potential issue with the core using CLOCK_TICK_RATE to
maintain xtime and CLOCK_TICK_RATE value on ppc32 is pure crap, but that
is a different problem, this patch at least brings us back to our
previous situation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Wed, 5 Oct 2005 07:36:02 +0000 (08:36 +0100)]
[PATCH] fix the breakage in sparc headers
If we switch extern inline to static inline, we'd better switch the
pre-declarations we use to say that these puppies have
__attribute_const__ on them.
Otherwise we get extern declaration followed by static inline one.
Which makes gcc unhappy, and for a good reason...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Randy Dunlap [Wed, 5 Oct 2005 05:44:45 +0000 (22:44 -0700)]
[RPC]: fix sparse gfp nocast warnings
Fix nocast sparse warnings:
net/rxrpc/call.c:2013:25: warning: implicit cast to nocast type
net/rxrpc/connection.c:538:46: warning: implicit cast to nocast type
net/sunrpc/sched.c:730:36: warning: implicit cast to nocast type
net/sunrpc/sched.c:734:56: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Wed, 5 Oct 2005 05:43:04 +0000 (22:43 -0700)]
[AF_KEY]: fix sparse gfp nocast warnings
Fix implicit nocast warnings in net/key code:
net/key/af_key.c:195:27: warning: implicit cast to nocast type
net/key/af_key.c:1439:28: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Wed, 5 Oct 2005 05:41:48 +0000 (22:41 -0700)]
[DECNET]: fix sparse gfp nocast warnings
Fix implicit nocast warnings in decnet code:
net/decnet/af_decnet.c:458:40: warning: implicit cast to nocast type
net/decnet/dn_nsp_out.c:125:35: warning: implicit cast to nocast type
net/decnet/dn_nsp_out.c:219:29: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Wed, 5 Oct 2005 05:41:16 +0000 (22:41 -0700)]
[CONNECTOR]: fix sparse gfp nocast warnings
Fix implicit nocast warnings in connector code:
drivers/connector/connector.c:102:24: warning: implicit cast to nocast type
drivers/connector/connector.c:114:45: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Wed, 5 Oct 2005 05:38:44 +0000 (22:38 -0700)]
[ATM]: fix sparse gfp nocast warnings
Fix implicit nocast warnings in atm code:
net/atm/atm_misc.c:35:44: warning: implicit cast to nocast type
drivers/atm/fore200e.c:183:33: warning: implicit cast to nocast type
Also use kzalloc() instead of kmalloc().
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Roskin [Wed, 5 Oct 2005 01:33:10 +0000 (21:33 -0400)]
[PATCH] orinoco: Information leakage due to incorrect padding
The orinoco driver can send uninitialized data exposing random pieces of
the system memory. This happens because data is not padded with zeroes
when its length needs to be increased.
Reported by Meder Kydyraliev <meder@o0o.nu>
Signed-off-by: Pavel Roskin <proski@gnu.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Andi Kleen [Tue, 4 Oct 2005 22:21:39 +0000 (00:21 +0200)]
[PATCH] x86_64: Drop global bit from early low mappings
Drop global bit from early low mappings
Suggested by Linus, originally also proposed by Suresh.
This fixes a race condition with early start of udev, originally
tracked down by Suresh B. Siddha. The problem was that switching
to the user space VM would not clear the global low mappings
for the beginning of memory, which lead to memory corruption.
Drop the global bits.
The kernel mapping stays global because it should stay constant.
Sascha Hauer [Tue, 4 Oct 2005 22:17:52 +0000 (23:17 +0100)]
[ARM] 2950/1: i.MX gpio setup function
Patch from Sascha Hauer
Current implementation of imx_gpio_mode does not allow to
configure all alternate routing possibilities of the i.MX. With
this patch every bit in the gpio setup registers has a
corresponding bit in the gpio_mode parameter, so every routing
should be possible now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allan Graves [Tue, 4 Oct 2005 18:53:52 +0000 (14:53 -0400)]
[PATCH] uml: Fix sysrq-r support for skas mode
The old code had the IP and SP coming from the registers in the thread
struct, which are completely wrong since those are the userspace
registers. This fixes that by pulling the correct values from the
jmp_buf in which the kernel state of each thread is stored.
Signed-off-by: Allan Graves <allan.graves@oracle.com> Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Tue, 4 Oct 2005 16:48:44 +0000 (17:48 +0100)]
[PATCH] bfs iget() abuses
bfs_fill_super() walks the inode table to get the bitmap of free inodes
and collect stats. It has no business using iget() for that - it's a
lot of extra work, extra icache pollution and more complex code.
Switched to walking the damn thing directly.
Note: that also allows to kill ->i_dsk_ino in there - separate patch if
Tigran can confirm that this field can be zero only for deleted inodes
(i.e. something that could only be found during that scan and not by
normal lookups).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Robert Olsson [Tue, 4 Oct 2005 20:01:58 +0000 (13:01 -0700)]
[IPV4]: fib_trie root-node expansion
The patch below introduces special thresholds to keep root node in the trie
large. This gives a flatter tree at the cost of a modest memory increase.
Overall it seems to be gain and this was also proposed by one the authors
of the paper in recent a seminar.
Main table after loading 123 k routes.
Aver depth: 3.30
Max depth: 9
Root-node size 12 bits
Total size: 4044 kB
With the patch:
Aver depth: 2.78
Max depth: 8
Root-node size 15 bits
Total size: 4150 kB
An increase of 8-10% was seen in forwading performance for an rDoS attack.
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
NTFS: Fix a 64-bitness bug where a left-shift could overflow a 32-bit variable
which we now cast to 64-bit first (fs/ntfs/mft.c::map_mft_record_page().
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
NTFS: Fix a stupid bug in __ntfs_bitmap_set_bits_in_run() which caused the
count to become negative and hence we had a wild memset() scribbling
all over the system's ram.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Ion Badulescu [Tue, 4 Oct 2005 02:31:36 +0000 (22:31 -0400)]
[netdrvr starfire] fix highmem and broken firmware issues
Unfortunately, [your patch] might address the crash but doesn't address
the real problem. It turns out that the problem is one of padding
(the firmware cksum engine works only on 32-bit chunks, yuck), so
the special casing for length == 1 wasn't sufficient anyway.
This patch addresses the issue, as well the other issue of i386 +
CONFIG_HIGHMEM being broken. It is pretty much the same workaround
that Adaptec themselves used in their Windows driver. I have yet to
check if it fixes the problem when the skb is non-linear, but this
patch _will_ solve the problem for 99% of the users out there (those
not using sendfile).
Signed-off-by: Ion Badulescu <ionut@badula.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The patch below is necessary to allow my Digital DS21143 Tulip rev 48
ethernet interface to work in a 10Mbit Half Duplex network. Without
it, the driver keeps retrying other modes in an endless loop. It seems
like someone already had the same problem with a rev 65 board :)
Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Peter Tiedemann <ptiedem@de.ibm.com>
From: Frank Pavlic <pavlic@de.ibm.com>
minor qeth fixes:
- free old skb in qeth_realloc_headroom after duplicating skb
- disable IPV6 support for Hipersockets devices
- call ccw_device_set_offline on every channel regardless
of the return value of the prior ccw_device_set_offline calls
- allocate qdio structures in DMA-area
- schedule recovery of appropriate card
when cable has been inserted again.
- add missing initialization of card->lock
- write sequence number in skb->cb for SNA protocol which
requires strictly serialized packets.
Herbert Xu [Mon, 3 Oct 2005 21:35:55 +0000 (14:35 -0700)]
[IPV4]: Replace __in_dev_get with __in_dev_get_rcu/rtnl
The following patch renames __in_dev_get() to __in_dev_get_rtnl() and
introduces __in_dev_get_rcu() to cover the second case.
1) RCU with refcnt should use in_dev_get().
2) RCU without refcnt should use __in_dev_get_rcu().
3) All others must hold RTNL and use __in_dev_get_rtnl().
There is one exception in net/ipv4/route.c which is in fact a pre-existing
race condition. I've marked it as such so that we remember to fix it.
This patch is based on suggestions and prior work by Suzanne Wood and
Paul McKenney.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 3 Oct 2005 21:18:10 +0000 (14:18 -0700)]
[IPV4]: Fix "Proxy ARP seems broken"
Meelis Roos <mroos@linux.ee> wrote:
> RK> My firewall setup relies on proxyarp working. However, with 2.6.14-rc3,
> RK> it appears to be completely broken. The firewall is 212.18.232.186,
>
> Same here with some kernel between 14-rc2 and 14-rc3 - no reposnse to
> ARP on a proxyarp gateway. Sorry, no exact revison and no more debugging
> yet since it'a a production gateway.
The breakage is caused by the change to use the CB area for flagging
whether a packet has been queued due to proxy_delay. This area gets
cleared every time arp_rcv gets called. Unfortunately packets delayed
due to proxy_delay also go through arp_rcv when they are reprocessed.
In fact, I can't think of a reason why delayed proxy packets should go
through netfilter again at all. So the easiest solution is to bypass
that and go straight to arp_process.
This is essentially what would've happened before netfilter support
was added to ARP.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
During the build for ARM machine type "fortunet", this error occurred:
CC net/sysctl_net.o
net/sysctl_net.c:36: error: 'core_table' undeclared here (not in a function)
It appears that the following configuration settings cause this error
due to a missing include:
CONFIG_SYSCTL=y
CONFIG_NET=y
# CONFIG_INET is not set
core_table appears to be declared in net/sock.h. if CONFIG_INET were
defined, net/sock.h would have been included via:
sysctl_net.c -> net/ip.h -> linux/ip.h -> net/sock.h
so include it directly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 3 Oct 2005 21:13:38 +0000 (14:13 -0700)]
[INET]: speedup inet (tcp/dccp) lookups
Arnaldo and I agreed it could be applied now, because I have other
pending patches depending on this one (Thank you Arnaldo)
(The other important patch moves skc_refcnt in a separate cache line,
so that the SMP/NUMA performance doesnt suffer from cache line ping pongs)
1) First some performance data :
--------------------------------
tcp_v4_rcv() wastes a *lot* of time in __inet_lookup_established()
The most time critical code is :
sk_for_each(sk, node, &head->chain) {
if (INET_MATCH(sk, acookie, saddr, daddr, ports, dif))
goto hit; /* You sunk my battleship! */
}
The sk_for_each() does use prefetch() hints but only the begining of
"struct sock" is prefetched.
As INET_MATCH first comparison uses inet_sk(__sk)->daddr, wich is far
away from the begining of "struct sock", it has to bring into CPU
cache cold cache line. Each iteration has to use at least 2 cache
lines.
This can be problematic if some chains are very long.
2) The goal
-----------
The idea I had is to change things so that INET_MATCH() may return
FALSE in 99% of cases only using the data already in the CPU cache,
using one cache line per iteration.
3) Description of the patch
---------------------------
Adds a new 'unsigned int skc_hash' field in 'struct sock_common',
filling a 32 bits hole on 64 bits platform.
struct sock_common {
unsigned short skc_family;
volatile unsigned char skc_state;
unsigned char skc_reuse;
int skc_bound_dev_if;
struct hlist_node skc_node;
struct hlist_node skc_bind_node;
atomic_t skc_refcnt;
+ unsigned int skc_hash;
struct proto *skc_prot;
};
Store in this 32 bits field the full hash, not masked by (ehash_size -
1) Using this full hash as the first comparison done in INET_MATCH
permits us immediatly skip the element without touching a second cache
line in case of a miss.
Suppress the sk_hashent/tw_hashent fields since skc_hash (aliased to
sk_hash and tw_hash) already contains the slot number if we mask with
(ehash_size - 1)
- Adds a prefetch(head->chain.first) in
__inet_lookup_established()/__tcp_v4_check_established() and
__inet6_lookup_established()/__tcp_v6_check_established() and
__dccp_v4_check_established() to bring into cache the first element of the
list, before the {read|write}_lock(&head->lock);
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com> Acked-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Mon, 3 Oct 2005 21:02:39 +0000 (14:02 -0700)]
[TG3]: Refine AMD K8 write-reorder chipset test.
Test for VIA K8T800 north bridge instead of AMD K8 HyperTransport
bridge based on new information from Andi Kleen. The AMD
HyperTransport interface is not responsible for PCI transactions
and so the re-ordering is more likely done by the VIA north bridge.
This code is subject to change if we get more information from AMD
or VIA.
PCI Express devices are excluded from doing the read flush since all
chipsets in the write_reorder list are PCI chipsets.
Signed-off-by: Michael Chan <mchan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 3 Oct 2005 20:57:23 +0000 (13:57 -0700)]
[NET]: Fix packet timestamping.
I've found the problem in general. It affects any 64-bit
architecture. The problem occurs when you change the system time.
Suppose that when you boot your system clock is forward by a day.
This gets recorded down in skb_tv_base. You then wind the clock back
by a day. From that point onwards the offset will be negative which
essentially overflows the 32-bit variables they're stored in.
In fact, why don't we just store the real time stamp in those 32-bit
variables? After all, we're not going to overflow for quite a while
yet.
When we do overflow, we'll need a better solution of course.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH] x86_64: Fix numa node topology detection for srat based x86_64 boxes
2.6.14-rc2 does not assign cpus to proper nodeids on our em64t numa boxen.
Our boxes use acpi srat for parsing the numa information.
srat_detect_node() used phys_proc_id[] to get to the cpu's local apic id,
but phys_proc_id[] represents the cpu<->initial_apic_id mapping. The
following patch fixes this problem. Now apicid_to_node[] is properly
indexed with the local apic id.
James Bottomley [Sat, 1 Oct 2005 14:38:05 +0000 (09:38 -0500)]
[SCSI] Legacy MegaRAID: Fix READ CAPACITY
Some Legacy megaraid cards can't actually cope with the scatter/gather
version of the READ CAPACITY command (which is what we now send them
since altering all SCSI internal I/O to go via the block layer). Fix
this (and a few other broken megaraid driver assumptions) by sending
the non-sg version of the command if the sg list only has a single
element.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Catalin Marinas [Sun, 2 Oct 2005 21:34:35 +0000 (22:34 +0100)]
[ARM] 2943/1: Clear the exclusive monitor in v6_early_abort
Patch from Catalin Marinas
Data abort caused by ldrex/strex can leave the exclusive monitor in an
unpredictable state. It is recommended that a clrex/strex is performed to
clear this state.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
James Bottomley [Sun, 2 Oct 2005 20:22:35 +0000 (15:22 -0500)]
[SCSI] aic7xxx/aic79xx: fix module removal path not to panic
In these drivers, scsi_remove_host() is called too late, at the point
it is called, the driver has already shut down too far to accept any
I/O that the shutdown might generate. Any generated I/O actually
triggers a panic.
Fix this by calling scsi_remove_host() as early as possible and not
calling scsi_host_put() until just before we kfree the ahc_softc.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Sun, 2 Oct 2005 17:59:49 +0000 (12:59 -0500)]
[SCSI] fix potential panic with proc on module removal
There's a problem in our host release in that it calls
scsi_proc_hostdir_rm(). However, if you hold a reference to the host as
you remove the module, the host template (which proc uses) will be freed
and the system will panic when the host device is finally released.
Fix this by moving scsi_proc_hostdir_rm() to where it should be: in
scsi_remove_host().
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Russell King [Sun, 2 Oct 2005 17:12:03 +0000 (18:12 +0100)]
[ARM] Fix init printk for EBSA110 network driver, and link timer
Arrange for the initialisation printks to happen after we've
registered the network interface, so we know what name the
device is. Also, check the link every 500ms (and use
msecs_to_jiffies.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sven Henkel [Sat, 1 Oct 2005 22:30:33 +0000 (08:30 +1000)]
[PATCH] ppc32: Add new iBook 12" to PowerMac models table
This adds the new iBook G4 (manufactured after July 2005) to the
PowerMac models table. The model name (PowerBook6,7) is taken from a
12" iBook, I don't know if it also matches the 14" version. The patch
applies to a vanilla 2.6.13.2 kernel.
Signed-off-by: Sven Henkel <shenkel@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sven Henkel [Sat, 1 Oct 2005 22:29:18 +0000 (08:29 +1000)]
[PATCH] pmac/radeonfb: Add suspend support for M11 chip in new iBook 12"
This adds suspend support for the Radeon M11 chip in 12" iBooks
manufactured after July 2005. I don't know if the new 14" iBooks also
have that chip, so they might also be supported.
The chip identifies itself as "RV350 NV" (pci id 0x4e56), revision 0x80.
Apple calls it "Snowy", xfree86 names it "ATI FireGL Mobility T2 (M11)
NV (AGP)". So, we seem to be lucky here: The suspend-code for the M10
(which also is a "RV350 NV") works flawless for that chip.
Signed-off-by: Sven Henkel <shenkel@gmail.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Linus Torvalds [Sat, 1 Oct 2005 18:04:18 +0000 (11:04 -0700)]
Fix inequality comparison against "task->state"
We should always use bitmask ops, rather than depend on some ordering of
the different states. With the TASK_NONINTERACTIVE flag, the inequality
doesn't really work.
Oleg Nesterov argues (likely correctly) that this test is unnecessary in
the first place. However, the minimal fix for now is to at least make
it work in the presense of TASK_NONINTERACTIVE. Waiting for consensus
from Roland & co on potential bigger cleanups.
projects / linux-2.6 / log