avr32: Power Management support ("standby" and "mem" modes)
Implement Standby support. In this mode, we'll suspend all drivers,
put the SDRAM in self-refresh mode and switch off the HSB bus
("frozen" mode.)
Implement Suspend-to-mem support. In this mode, we suspend all
drivers, put the SDRAM into self-refresh mode and switch off all
internal clocks except the 32 kHz oscillator ("stop" mode.)
The lowest-level suspend code runs from a small portion of SRAM
allocated at startup time. This gets rid of a small potential race
with the SDRAM where we might try to enter self-refresh mode in the
middle of an icache burst. We also relocate all interrupt and
exception handlers to SRAM during the small window when we enter and
exit the low-power modes.
We don't need to do any special tricks to start and stop the PLL. The
main clock is automatically gated by hardware until the PLL is stable.
This implements suspend and resume callbacks for the macb driver. We may
have to do some more to gracefully shut the MAC down, but this at least
prevents the macb from waking the system when hooked up to a busy
network.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Patrice Vilchez <patrice.vilchez@rfo.atmel.com> Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
atmel_serial: Drain console TX shifter before suspending
Funny things may happen if we stop the USART clock before the shifter is
empty. Prevent this from happening by waiting until the shifter is
completely drained before allowing suspend to continue.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Cc: Andrew Victor <linux@maxim.org.za>
atmel_serial: Fix build on avr32 with CONFIG_PM enabled
AVR32 doesn't have at91_suspend_entering_slow_clock(). Just assume the
clock will keep running for now.
David has a better solution for this, but this works for now. Leaving
the USART clock running won't prevent the PM code from entering deep
power-down modes anyway.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com> Cc: David Brownell <david-b@pacbell.net> Cc: Andrew Victor <linux@maxim.org.za>
Using a quicklist to allocate PTEs might be slightly faster than using
the page allocator directly since we might avoid zeroing the page
after each allocation.
Use a quicklist to allocate process PGDs. This is expected to be
slightly faster since we need to copy entries from swapper_pg_dir,
which can stay around for pages on the PGD quick list.
avr32: Cover the kernel page tables in the user PGDs
Expand the per-process PGDs so that they cover the kernel virtual
memory area as well. This simplifies the TLB miss handler fastpath
since it doesn't have to check for kernel addresses anymore.
If a TLB miss happens on a kernel address and a second-level page
table can't be found, we check swapper_pg_dir and copy the PGD entry
into the user PGD if it can be found there.
Instead of storing physical addresses along with page flags in the
PGD, store virtual addresses and use NULL to indicate a not present
second-level page table. A non-page-aligned page table indicates a bad
PMD.
This simplifies the TLB miss handler since it no longer has to check
the Present bit and no longer has to convert the PGD entry from
physical to virtual address. Instead, it has to check for a NULL
entry, which is slightly cheaper than either.
This and the following patches aim to optimize the code dealing with
page tables and TLB operations. Each patch reduces the time it takes
to gzip a 16 MB file slightly, but I expect things like fork() and
mmap() will improve somewhat more.
This patch deals with the low-level TLB operations:
* Remove unused _TLBEHI_I define
* Use gcc builtins instead of inline assembly
* Remove a few unnecessary pipeline flushes and nops
* Introduce NR_TLB_ENTRIES define and use it instead of hardcoding it
to 32 a few places throughout the code.
* Use sysreg bitops instead of hardcoded shifts and masks
* Make a few needlessly global functions static
avr32: Move setup_platform() into chip-specific file
Combine at32_clock_init() and at32_portmux_init() into
setup_platform() and remove setup_platform() from at32ap.c. No
functional change since all setup_platform() ever did was call those
two functions.
Kill the special exception handler sections .tlbx.ex.text,
.tlbr.ex.text, tlbw.ex.text and .scall.text. Use .org instead to place
the handlers at the required offsets from EVBA.
David Brownell [Wed, 18 Jun 2008 09:31:43 +0000 (02:31 -0700)]
at32ap700x spi: enable pullups on MISO
This is a minor tweak to the at32ap700x pin configuration for the SPI
input pin (MISO), enabling the on-chip weak pullup (typical 190K) to
(a) ensure a fixed data value for missing or input-only slaves;
(b) prevent power waste associated with inputs floating near VDDIO/2.
Atmel's boards have no external pullup or pulldown on these pins, so
it's unlikely other boards would address these issues with external
pulldowns. Were there trouble, board-specific code could turn off
the relevant pullup(s).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
avr32: Add pin configuration choice to LCDC peripheral
This patch lets the board code choose which pin out to use for the LCD
interface.
On AT32AP7000 the LCDC is wired to two sets of pins, which lets the user
choose between dual ethernet and 32-bit EBI. For the ATNGW100 board it
is vital to have the choice to select the alternative pinout since this
pinout is routed to the external headers.
Update ATSTK1002 and ATSTK1004 to use the new interface.
David Brownell [Tue, 10 Jun 2008 11:55:52 +0000 (13:55 +0200)]
avr32: minor GPIO handling updates
On the odd chance some code uses a pin as a GPIO IRQ without calling
gpio_request() or gpio_direction_input(), the debug dump should still
show its pin status.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Martin Koegler [Wed, 28 May 2008 18:50:07 +0000 (20:50 +0200)]
avr32: Fix sigaltstack behaviour
A signal handler should be able to change the signal stack used for the
next signal by altering the ucontext_t passed as a parameter to the
handler. This does not currently work on avr32 since it doesn't update
the in-kernel signal context from the ucontext_t upon signal handler
return.
Fix it by adding a call to do_sigaltstack() from sys_rt_sigreturn(),
bringing it in line with most other architectures.
Some non-PCI drivers need the PCI variant of the DMA mapping API.
Include <asm-generic/pci-dma-compat.h> to provide this through the
non-PCI DMA mapping API.
Linus Torvalds [Wed, 25 Jun 2008 01:12:33 +0000 (18:12 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Eliminate NULL test after alloc_bootmem in iosapic_alloc_rte()
[IA64] Handle count==0 in sn2_ptc_proc_write()
[IA64] Fix boot failure on ia64/sn2
Linus Torvalds [Wed, 25 Jun 2008 01:09:06 +0000 (18:09 -0700)]
Merge branch 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: Remove now unused structs from kvm_para.h
x86: KVM guest: Use the paravirt clocksource structs and functions
KVM: Make kvm host use the paravirt clocksource structs
x86: Make xen use the paravirt clocksource structs and functions
x86: Add structs and functions for paravirt clocksource
KVM: VMX: Fix host msr corruption with preemption enabled
KVM: ioapic: fix lost interrupt when changing a device's irq
KVM: MMU: Fix oops on guest userspace access to guest pagetable
KVM: MMU: large page update_pte issue with non-PAE 32-bit guests (resend)
KVM: MMU: Fix rmap_write_protect() hugepage iteration bug
KVM: close timer injection race window in __vcpu_run
KVM: Fix race between timer migration and vcpu migration
Jie Luo [Tue, 24 Jun 2008 17:38:31 +0000 (10:38 -0700)]
enable bus mastering on i915 at resume time
On 9xx chips, bus mastering needs to be enabled at resume time for much of the
chip to function. With this patch, vblank interrupts will work as expected
on resume, along with other chip functions. Fixes kernel bugzilla #10844.
Signed-off-by: Jie Luo <clotho67@gmail.com> Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gerd Hoffmann [Tue, 3 Jun 2008 14:17:32 +0000 (16:17 +0200)]
x86: KVM guest: Use the paravirt clocksource structs and functions
This patch updates the kvm host code to use the pvclock structs
and functions, thereby making it compatible with Xen.
The patch also fixes an initialization bug: on SMP systems the
per-cpu has two different locations early at boot and after CPU
bringup. kvmclock must take that in account when registering the
physical address within the host.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Gerd Hoffmann [Tue, 3 Jun 2008 14:17:29 +0000 (16:17 +0200)]
x86: Add structs and functions for paravirt clocksource
This patch adds structs for the paravirt clocksource ABI
used by both xen and kvm (pvclock-abi.h).
It also adds some helper functions to read system time and
wall clock time from a paravirtual clocksource (pvclock.[ch]).
They are based on the xen code. They are enabled using
CONFIG_PARAVIRT_CLOCK.
Subsequent patches of this series will put the code in use.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch changes the computation for zero_metapath_length(), which it
renames to metapath_branch_start(). When you are extending the metadata
tree, The indirect blocks that point to the new data block must either
diverge from the existing tree either at the inode, or at the first
indirect block. They can diverge at the first indirect block because the
inode has room for 483 pointers while the indirect blocks have room for
509 pointers, so when the tree is grown, there is some free space in the
first indirect block. What metapath_branch_start() now computes is the
height where the first indirect block for the new data block is located.
It can either be 1 (if the indirect block diverges from the inode) or 2
(if it diverges from the first indirect block).
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com> Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Julia Lawall [Tue, 24 Jun 2008 08:22:05 +0000 (10:22 +0200)]
[IA64] Eliminate NULL test after alloc_bootmem in iosapic_alloc_rte()
As noted by Akinobu Mita alloc_bootmem and related functions never return
NULL and always return a zeroed region of memory. Thus a NULL test or
memset after calls to these functions is unnecessary.
Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Tony Luck <tony.luck@intel.com>
Cliff Wickman [Tue, 24 Jun 2008 17:20:06 +0000 (10:20 -0700)]
[IA64] Handle count==0 in sn2_ptc_proc_write()
The fix applied in e0c6d97c65e0784aade7e97b9411f245a6c543e7
"security hole in sn2_ptc_proc_write" didn't take into account
the case where count==0 (which results in a buffer underrun
when adding the trailing '\0'). Thanks to Andi Kleen for
pointing this out.
Signed-off-by: Cliff Wickman <cpw@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Non-PAE operation has been deprecated in Xen for a while, and is
rarely tested or used. xen-unstable has now officially dropped
non-PAE support. Since Xen/pvops' non-PAE support has also been
broken for a while, we may as well completely drop it altogether.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@elte.hu>
Avi Kivity [Tue, 24 Jun 2008 08:48:49 +0000 (11:48 +0300)]
KVM: VMX: Fix host msr corruption with preemption enabled
Switching msrs can occur either synchronously as a result of calls to
the msr management functions (usually in response to the guest touching
virtualized msrs), or asynchronously when preempting a kvm thread that has
guest state loaded. If we're unlucky enough to have the two at the same
time, host msrs are corrupted and the machine goes kaput on the next syscall.
Most easily triggered by Windows Server 2008, as it does a lot of msr
switching during bootup.
Avi Kivity [Tue, 17 Jun 2008 22:36:36 +0000 (15:36 -0700)]
KVM: ioapic: fix lost interrupt when changing a device's irq
The ioapic acknowledge path translates interrupt vectors to irqs. It
currently uses a first match algorithm, stopping when it finds the first
redirection table entry containing the vector. That fails however if the
guest changes the irq to a different line, leaving the old redirection table
entry in place (though masked). Result is interrupts not making it to the
guest.
Fix by always scanning the entire redirection table.
Avi Kivity [Thu, 12 Jun 2008 13:54:41 +0000 (16:54 +0300)]
KVM: MMU: Fix oops on guest userspace access to guest pagetable
KVM has a heuristic to unshadow guest pagetables when userspace accesses
them, on the assumption that most guests do not allow userspace to access
pagetables directly. Unfortunately, in addition to unshadowing the pagetables,
it also oopses.
This never triggers on ordinary guests since sane OSes will clear the
pagetables before assigning them to userspace, which will trigger the flood
heuristic, unshadowing the pagetables before the first userspace access. One
particular guest, though (Xenner) will run the kernel in userspace, triggering
the oops. Since the heuristic is incorrect in this case, we can simply
remove it.
Marcelo Tosatti [Wed, 11 Jun 2008 23:32:40 +0000 (20:32 -0300)]
KVM: MMU: large page update_pte issue with non-PAE 32-bit guests (resend)
kvm_mmu_pte_write() does not handle 32-bit non-PAE large page backed
guests properly. It will instantiate two 2MB sptes pointing to the same
physical 2MB page when a guest large pte update is trapped.
Instead of duplicating code to handle this, disallow directory level
updates to happen through kvm_mmu_pte_write(), so the two 2MB sptes
emulating one guest 4MB pte can be correctly created by the page fault
handling path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
rmap_next() does not work correctly after rmap_remove(), as it expects
the rmap chains not to change during iteration. Fix (for now) by restarting
iteration from the beginning.
Marcelo Tosatti [Fri, 6 Jun 2008 19:37:36 +0000 (16:37 -0300)]
KVM: close timer injection race window in __vcpu_run
If a timer fires after kvm_inject_pending_timer_irqs() but before
local_irq_disable() the code will enter guest mode and only inject such
timer interrupt the next time an unrelated event causes an exit.
It would be simpler if the timer->pending irq conversion could be done
with IRQ's disabled, so that the above problem cannot happen.
For now introduce a new vcpu requests bit to cancel guest entry.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Marcelo Tosatti [Fri, 6 Jun 2008 19:37:35 +0000 (16:37 -0300)]
KVM: Fix race between timer migration and vcpu migration
A guest vcpu instance can be scheduled to a different physical CPU
between the test for KVM_REQ_MIGRATE_TIMER and local_irq_disable().
If that happens, the timer will only be migrated to the current pCPU on
the next exit, meaning that guest LAPIC timer event can be delayed until
a host interrupt is triggered.
Fix it by cancelling guest entry if any vcpu request is pending. This
has the side effect of nicely consolidating vcpu->requests checks.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Linus Torvalds [Mon, 23 Jun 2008 23:25:11 +0000 (16:25 -0700)]
Merge branch 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'hotfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: nfs_updatepage(): don't mark page as dirty if an error occurred
NFS: Fix filehandle size comparisons in the mount code
NFS: Reduce the NFS mount code stack usage.
Linus Torvalds [Mon, 23 Jun 2008 19:48:50 +0000 (12:48 -0700)]
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: refactor wait_for_completion_timeout()
sched: fix wait_for_completion_timeout() spurious failure under heavy load
sched: rt: dont stop the period timer when there are tasks wanting to run
Linus Torvalds [Mon, 23 Jun 2008 19:48:17 +0000 (12:48 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
xen: don't drop NX bit
xen: mask unwanted pte bits in __supported_pte_mask
xen: Use wmb instead of rmb in xen_evtchn_do_upcall().
x86: fix NULL pointer deref in __switch_to
Nick Piggin [Mon, 23 Jun 2008 12:30:30 +0000 (14:30 +0200)]
mm: fix race in COW logic
There is a race in the COW logic. It contains a shortcut to avoid the
COW and reuse the page if we have the sole reference on the page,
however it is possible to have two racing do_wp_page()ers with one
causing the other to mistakenly believe it is safe to take the shortcut
when it is not. This could lead to data corruption.
Process 1 and process2 each have a wp pte of the same anon page (ie.
one forked the other). The page's mapcount is 2. Then they both
attempt to write to it around the same time...
write private key into page
read from page
ptep_clear_flush()
set_pte_at(pte of new_page)
Fix this by moving the page_remove_rmap of the old page after the pte
clear and flush. Potentially the entire branch could be moved down
here, but in order to stay consistent, I won't (should probably move all
the *_mm_counter stuff with one patch).
Signed-off-by: Nick Piggin <npiggin@suse.de> Acked-by: Hugh Dickins <hugh@veritas.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"This broke vmware 6.0.4.
Jun 22 14:53:03.845: vmx| NOT_IMPLEMENTED
/build/mts/release/bora-93057/bora/vmx/main/vmmonPosix.c:774"
and the reason seems to be that there's an old bug in how we handle do
FOLL_ANON on VM_SHARED areas in get_user_pages(), but since it only
triggered if the whole page table was missing, nobody had apparently hit
it before.
The recent changes to 'follow_page()' made the FOLL_ANON logic trigger
not just for whole missing page tables, but for individual pages as
well, and exposed this problem.
This fixes it by making the test for when FOLL_ANON is used more
careful, and also makes the code easier to read and understand by moving
the logic to a separate inline function.
Reported-and-tested-by: Jeff Chua <jeff.chua.linux@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eli Cohen [Mon, 23 Jun 2008 16:29:58 +0000 (09:29 -0700)]
IB/mthca: Clear ICM pages before handing to FW
Current memfree FW has a bug which in some cases, assumes that ICM
pages passed to it are cleared. This patch uses __GFP_ZERO to
allocate all ICM pages passed to the FW. Once firmware with a fix is
released, we can make the workaround conditional on firmware version.
This fixes the bug reported by Arthur Kepner <akepner@sgi.com> here:
http://lists.openfabrics.org/pipermail/general/2008-May/050026.html
Cc: <stable@kernel.org> Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Rewritten to be a one-liner using __GFP_ZERO instead of vmap()ing
ICM memory and memset()ing it to 0. - Roland ]
Thomas Gleixner [Mon, 23 Jun 2008 09:21:58 +0000 (11:21 +0200)]
futexes: fix fault handling in futex_lock_pi
This patch addresses a very sporadic pi-futex related failure in
highly threaded java apps on large SMP systems.
David Holmes reported that the pi_state consistency check in
lookup_pi_state triggered with his test application. This means that
the kernel internal pi_state and the user space futex variable are out
of sync. First we assumed that this is a user space data corruption,
but deeper investigation revieled that the problem happend because the
pi-futex code is not handling a fault in the futex_lock_pi path when
the user space variable needs to be fixed up.
The fault happens when a fork mapped the anon memory which contains
the futex readonly for COW or the page got swapped out exactly between
the unlock of the futex and the return of either the new futex owner
or the task which was the expected owner but failed to acquire the
kernel internal rtmutex. The current futex_lock_pi() code drops out
with an inconsistent in case it faults and returns -EFAULT to user
space. User space has no way to fixup that state.
When we wrote this code we thought that we could not drop the hash
bucket lock at this point to handle the fault.
After analysing the code again it turned out to be wrong because there
are only two tasks involved which might modify the pi_state and the
user space variable:
- the task which acquired the rtmutex
- the pending owner of the pi_state which did not get the rtmutex
Both tasks drop into the fixup_pi_state() function before returning to
user space. The first task which acquired the hash bucket lock faults
in the fixup of the user space variable, drops the spinlock and calls
futex_handle_fault() to fault in the page. Now the second task could
acquire the hash bucket lock and tries to fixup the user space
variable as well. It either faults as well or it succeeds because the
first task already faulted the page in.
One caveat is to avoid a double fixup. After returning from the fault
handling we reacquire the hash bucket lock and check whether the
pi_state owner has been modified already.
Reported-by: David Holmes <david.holmes@sun.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: David Holmes <david.holmes@sun.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: <stable@kernel.org> Signed-off-by: Ingo Molnar <mingo@elte.hu>
kernel/futex.c | 93 ++++++++++++++++++++++++++++++++++++++++++++-------------
1 file changed, 73 insertions(+), 20 deletions(-)
Linus Torvalds [Sun, 22 Jun 2008 19:23:15 +0000 (12:23 -0700)]
Fix performance regression on lmbench select benchmark
Christian Borntraeger reported that reinstating cond_resched() with
CONFIG_PREEMPT caused a performance regression on lmbench:
For example select file 500:
23 microseconds
32 microseconds
and that's really because we totally unnecessarily do the cond_resched()
in the innermost loop of select(), which is just silly.
This moves it out from the innermost loop (which only ever loops ove the
bits in a single "unsigned long" anyway), which makes the performance
regression go away.
Reported-and-tested-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The zonelist patches caused the loop that checks for available
objects in permitted zones to not terminate immediately. One object
per zone per allocation may be allocated and then abandoned.
Break the loop when we have successfully allocated one object.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
netns: Don't receive new packets in a dead network namespace.
sctp: Make sure N * sizeof(union sctp_addr) does not overflow.
pppoe: warning fix
ipv6: Drop packets for loopback address from outside of the box.
ipv6: Remove options header when setsockopt's optlen is 0
mac80211: detect driver tx bugs
Receiving packets while we are cleaning up a network namespace is a
racy proposition. It is possible when the packet arrives that we have
removed some but not all of the state we need to fully process it. We
have the choice of either playing wack-a-mole with the cleanup routines
or simply dropping packets when we don't have a network namespace to
handle them.
Since the check looks inexpensive in netif_receive_skb let's just
drop the incoming packets.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning:
drivers/net/pppoe.c: In function 'pppoe_recvmsg':
drivers/net/pppoe.c:945: warning: comparison of distinct pointer types lacks a cast
because skb->len is unsigned int and total_len is size_t
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivan Kokshaysky [Fri, 20 Jun 2008 23:28:54 +0000 (03:28 +0400)]
alpha: resurrect Cypress IDE quirk
Which was removed in the hope that generic legacy IDE quirk in
drivers/pci/probe.c is sufficient for Cypress IDE.
It isn't, as this controller has non-standard BAR layout:
secondary channel registers are in the BAR0-1 of the second
PCI function - not in the BAR2-3 of the same function, as the
generic quirk routine assumes.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ivan Kokshaysky [Fri, 20 Jun 2008 23:28:31 +0000 (03:28 +0400)]
alpha: fix compile failures with gcc-4.3 (bug #10438)
Vast majority of these build failures are gcc-4.3 warnings
about static functions and objects being referenced from
non-static (read: "extern inline") functions, in conjunction
with our -Werror.
We cannot just convert "extern inline" to "static inline",
as people keep suggesting all the time, because "extern inline"
logic is crucial for generic kernel build.
So
- just make sure that all callees of critical "extern inline"
functions are also "extern inline";
- use "static inline", wherever it's possible.
traps.c: work around gcc-4.3 being too smart about array
bounds-checking.
TODO: add "gnu_inline" attribute to all our "extern inline"
functions to ensure desired behaviour with future compilers.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ivan Kokshaysky [Fri, 20 Jun 2008 23:26:21 +0000 (03:26 +0400)]
alpha: link failure fix
With built-in scsi disk driver, the final link fails with a following
error:
`.exit.text' referenced in section `.rodata' of drivers/built-in.o:
defined in discarded section `.exit.text' of drivers/built-in.o
This happens with -Os (CONFIG_CC_OPTIMIZE_FOR_SIZE=y) with all gcc-4
versions, and also with -O2 and gcc-4.3.
The problem is in sd.c:sd_major() being inlined into __exit function
exit_sd(), and the compiler generating a jump table in .rodata section
for the 'switch' statement in sd_major(). So we have references to
discarded section.
Fixed with a big hammer in the form of -fno-jump-tables.
Note that jump tables vs. discarded sections is a generic problem,
other architectures are just lucky not to suffer from it. But with
a slightly more complex switch/case statement it can be reproduced
on x86 as well. So maybe at some point we should consider
-fno-jump-tables as a generic compile option...
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ivan Kokshaysky [Fri, 20 Jun 2008 23:25:39 +0000 (03:25 +0400)]
alpha: fix module load failures on smp (bug #10926)
To calculate addresses of locally defined variables, GCC uses 32-bit
displacement from the GP. Which doesn't work for per cpu variables in
modules, as an offset to the kernel per cpu area is way above 4G.
The workaround is to force allocation of a GOT entry for per cpu variable
using ldq instruction with a 'literal' relocation.
I had to use custom asm/percpu.h, as a required argument magic doesn't
work with asm-generic/percpu.h macros.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
BAST: Remove old IDE driver
pcmcia ide kingston compactflash's have a new manufacturer id
pcmcia: add another pata/ide ID
pcmcia: add an pata/ide ID
ide: increase timeout in wait_drive_not_busy()
palm_bk3710: fix resource management
Linus Torvalds [Fri, 20 Jun 2008 19:41:10 +0000 (12:41 -0700)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
ieee1394: Kconfig menu touch-up
firewire: Kconfig menu touch-up
firewire: deadline for PHY config transmission
firewire: fw-ohci: unify printk prefixes
firewire: fill_bus_reset_event needs lock protection
firewire: fw-ohci: write selfIDBufferPtr before LinkControl.rcvSelfID
firewire: fw-ohci: disable PHY packet reception into AR context
firewire: fw-ohci: use of uninitialized data in AR handler
firewire: don't panic on invalid AR request buffer
Linus Torvalds [Fri, 20 Jun 2008 19:39:12 +0000 (12:39 -0700)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: no AC status notification
ACPI Exception (video-1721): UNKNOWN_STATUS_CODE, Cant attach device
Linus Torvalds [Fri, 20 Jun 2008 19:38:18 +0000 (12:38 -0700)]
Merge branch 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (21 commits)
drm: only trust core drm ioctls - driver ioctls are a mess.
drm/i915: add support for Intel series 4 chipsets.
drm/radeon: add hier-z registers for r300 and r500 chipsets
drm/radeon: use DSTCACHE_CTLSTAT rather than RB2D_DSTCACHE_CTLSTAT
drm/radeon: switch IGP gart to use radeon_write_agp_base()
drm/radeon: Restore sw interrupt on resume
drm/r500: add support for AGP based cards.
drm/radeon: fix texture uploads with large 3d textures (bug 13980)
drm/radeon: add initial r500 support.
drm/radeon: init pipe setup in kernel code.
drm/radeon: fixup radeon_do_engine_reset
drm/radeon: fix pixcache and purge/cache flushing registers
drm/radeon: write AGP_BASE_2 on chips that support it.
drm/radeon: merge IGP chip setup and fixup RS400 vs RS480 support
drm/radeon: IGP clean up register and magic numbers.
drm/rs690: set base 2 to 0.
drm/rs690: set all of gart base address.
radeon: add production microcode from AMD
drm: pcigart use proper pci map interfaces.
drm: the sg alloc ioctl should write back the handle to userspace
...
Linus Torvalds [Fri, 20 Jun 2008 19:37:55 +0000 (12:37 -0700)]
Merge branch 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
[agp]: fixup chipset flush for new Intel G4x.
agp: brown paper bag patch - put back the two lines it took out.
Linus Torvalds [Fri, 20 Jun 2008 19:37:13 +0000 (12:37 -0700)]
Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
softlockup: fix NMI hangs due to lock race - 2.6.26-rc regression
rcupreempt: remove export of rcu_batches_completed_bh
cpuset: limit the input of cpuset.sched_relax_domain_level
projects / linux-2.6 / log