Ben Collins [Mon, 12 Jun 2006 22:16:25 +0000 (18:16 -0400)]
eth1394: replace __constant_htons by htons
...and __constant_ntohs, __constant_ntohl, __constant_cpu_to_be32 too
where possible. Htons and friends are resolved to constants in these
places anyway. Also fix an endianess glitch in a log message, spotted
by Alexey Dobriyan.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:16:16 +0000 (18:16 -0400)]
ieee1394: adjust code formatting in highlevel.c
Replace spaces by tabulators, wrap lines at 80 columns, delete some
blank lines and superfluous braces. Collapse some if()-within-if()
constructs. Replace a literal CSR address by its preprocessor constant.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:16:01 +0000 (18:16 -0400)]
ieee1394: hl_irqs_lock is taken in hardware interrupt context
ohci1394 and pcilynx call highlevel_host_reset from their hardware
interrupt handler (via hpsb_selfid_complete). Therefore all readers and
writers of hl_irqs_lock have to disable interrupts. Reported by Jiri
Slaby and J. A. Magallon.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:15:50 +0000 (18:15 -0400)]
ieee1394_core: switch to kthread API
This gets also rid of the MODPOST warning "drivers/ieee1394/ieee1394.o -
Section mismatch: reference to .exit.text: from .smp_locks after '' (at
offset 0x18)".
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jody McIntyre <scjody@modernduck.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:15:40 +0000 (18:15 -0400)]
ieee1394: sbp2: Kconfig fix
We only support x86 and ppc, due to the use of bus_to_virt() and friends.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:15:20 +0000 (18:15 -0400)]
sbp2: fix deregistration of status fifo address space
The proper designator of an invalid CSR address is ~(u64)0, not (u64)0.
Use the correct value in initialization and deregistration.
Also, scsi_id->sbp2_lun does not need to be initialized twice.
(scsi_id was kzalloc'd.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:15:03 +0000 (18:15 -0400)]
Fix broken suspend/resume in ohci1394
I've been experimenting to track down the cause of suspend/resume problems
on my Compaq Presario X1050 laptop:
http://bugzilla.kernel.org/show_bug.cgi?id=6075
Essentially the ACPI Embedded Controller and keyboard controller would
get into a bizarre, confused state after resume.
I found that unloading the ohci1394 module before suspend and reloading it
after resume made the problem go away. Diffing the dmesg output from
resume, with and without the module loaded, I found that with the module
loaded I was missing these:
PM: Writing back config space on device 0000:02:00.0 at offset 1. (Was 2100080, writing 2100007)
PM: Writing back config space on device 0000:02:00.0 at offset 3. (Was 0, writing 8008)
PM: Writing back config space on device 0000:02:00.0 at offset 4. (Was 0, writing 90200000)
PM: Writing back config space on device 0000:02:00.0 at offset 5. (Was 1, writing 2401)
PM: Writing back config space on device 0000:02:00.0 at offset f. (Was 20000100, writing 2000010a)
The default PCI driver performs the pci_restore_state when no driver is
loaded for the device. When the ohci1394 driver is loaded, it is supposed
to do this, however it appears not to do so.
I created the patch below and tested it, and it appears to resolve the
suspend problems I was having with the module loaded. I only added in the
pci_save_state and pci_restore_state - however, though I know little of
this hardware, surely the driver should really be doing more than this when
suspending and resuming? Currently it does almost nothing, what if there
are commands in progress, etc?
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Cc: Jody McIntyre <scjody@modernduck.com> Cc: Ben Collins <bcollins@debian.org> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:14:14 +0000 (18:14 -0400)]
sbp2: fix S800 transfers if phys_dma is off
If sbp2 is forced to move data via ARM handler, the maximum packet size
allowed for S800 transfers exceeds ohci1394's buffer size on platforms
where PAGE_SIZE is 4096.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:13:42 +0000 (18:13 -0400)]
ohci1394: make phys_dma parameter read-only
Being able to switch physical DMA on and off at run time would be a nice
feature but a PITA to support by highlevel drivers and userspace apps.
Therefore allow it only to be set when the driver is being loaded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:13:32 +0000 (18:13 -0400)]
ohci1394: set address range properties
This patch supplies the API extension introduced by patch
"ieee1394: extend lowlevel API for address range properties"
with proper addresses.
Like in patch ''ohci1394, sbp2: fix "scsi_add_device failed"
with PL-3507 based devices'', 1 TeraByte is chosen as physical
upper bound. This leaves a window for the middle address range.
This choice is only relevant for adapters which actually have a
programmable pysical upper bound register. (Only ALi and
Fujitsu adapters are known for this. Most adapters have a fixed
bound at 4 GB.) The middle address range is suitable for posted
writes.
AFAIK, PCILynx does not support physical DMA nor posted writes,
therefore no equivalent change in the pcilynx driver is necessary.
There is also a driver for GP2Lynx, although not in mainline Linux.
I assume this hardware does not support these OHCI features either.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:13:21 +0000 (18:13 -0400)]
ieee1394: extend lowlevel API for address range properties
Host adapter hardware imposes certain restrictions and features on
address ranges. Instead of hard-wire such ranges into the ieee1394
core or even into protocol drivers, let lowlevel drivers specify
these ranges via struct hpsb_host.
Patch "ohci1394: set address range properties" must be applied too,
else hpsb_allocate_and_register_addrspace() won't work properly.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:13:11 +0000 (18:13 -0400)]
sbp2: log number of supported concurrent logins
Since this is useful information, promote it from a debug macro to
a regular log message. The message appears only if the user set
exclusive_login=0, therefore won't clutter the logs in normal use.
Also update the comment on exclusive_login.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Jody McIntyre <scjody@modernduck.com> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:12:59 +0000 (18:12 -0400)]
sbp2: remove manipulation of inquiry response
This code became ineffective a few Linux releases ago and is not
required anyway.
Note from Christoph Hellwig: scsi_cmnd.request_buffer is always a
scatterlist these days. Checking random bites into it and then
mangling the data in sbp2_check_sbp2_response will cause really bad
memory corruption when you're not lucky enough to have the check not
trigger by luck.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:12:49 +0000 (18:12 -0400)]
ieee1394: save RAM by using a single tlabel for broadcast transactions
Since broadcast transactions are already complete when the request has
been sent, the same transaction label can be reused all over again, see
IEEE 1394 7.3.2.5 and 6.2.4.3. Therefore we can reduce the footprint
of struct hpsb_host by the size of one struct hpsb_tlabel_pool.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:12:37 +0000 (18:12 -0400)]
ieee1394: support for slow links or slow 1394b phy ports
Add support for the following types of hardware:
+ nodes that have a link speed < PHY speed
+ 1394b PHYs that are less than S800 capable
+ 1394b/1394a adapter cable between two 1394b PHYs
Also, S1600 and S3200 are now supported if IEEE1394_SPEED_MAX is raised.
A probing function is added to nodemgr's config ROM fetching routine
which adjusts the allowable speed if an access problem was encountered.
Pros and Cons of the approach:
+ minimum code footprint to support this less widely used hardware
+ nearly no overhead for unaffected hardware
- ineffective before nodemgr began to read the ROM of affected nodes
- ineffective if ieee1394 is loaded with disable_nodemgr=1
The speed map CSRs which are published to the bus are not touched by the
patch.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Cc: Hakan Ardo <hakan@debian.org> Cc: Calculex <linux@calculex.com> Cc: Robert J. Kosinski <robk@cmcherald.com> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
This patch modifies the ohci1394.c file to enable and manage the "cycle too
long" interrupt.
If this interrupt occurs, the "LinkControl.CycleMaster" bit of the host
controller is reseted. This implies, that the host controller does not send
"cycle start" packet anymore freezing then the isochronous communication.
The management of the interrupt added by the patch is that when the interrupt
occurs, the OHCI irq handler prints a kernel log warning and then sets the
"LinkControl.CycleMaster" bit again resuming the isochronous communication.
Signed-off-by: Jean-Baptiste Mur <jeanbaptiste@maunakeatech.com> Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:11:07 +0000 (18:11 -0400)]
From: Arjan van de Ven <arjan@infradead.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Ben Collins <bcollins@debian.org> Cc: Jody McIntyre <scjody@modernduck.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Ben Collins [Mon, 12 Jun 2006 22:10:18 +0000 (18:10 -0400)]
sbp2: make TSB42AA9 workaround specific to Momobay CX-1
The workarounds are not required for DViCO Momobay FX-3A and AFAIR not
for Momobay CX-2. These contain an TSB42AA9A but feature the same
firmware_revision value as the older DViCO Momobay CX-1.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Paul Mackerras [Mon, 12 Jun 2006 02:16:26 +0000 (12:16 +1000)]
[PATCH] Fix for the PPTP hangs that have been reported
People have been reporting that PPP connections over ptys, such as
used with PPTP, will hang randomly when transferring large amounts of
data, for instance in http://bugzilla.kernel.org/show_bug.cgi?id=6530.
I have managed to reproduce the problem, and the patch below fixes the
actual cause.
The problem is not in fact in ppp_async.c but in n_tty.c. What
happens is that when pptp reads from the pty, we call read_chan() in
drivers/char/n_tty.c on the master side of the pty. That copies all
the characters out of its buffer to userspace and then calls
check_unthrottle(), which calls the pty unthrottle routine, which
calls tty_wakeup on the slave side, which calls ppp_asynctty_wakeup,
which calls tasklet_schedule. So far so good. Since we are in
process context, the tasklet runs immediately and calls
ppp_async_process(), which calls ppp_async_push, which calls the
tty->driver->write function to send some more output.
However, tty->driver->write() returns zero, because the master
tty->receive_room is still zero. We haven't returned from
check_unthrottle() yet, and read_chan() only updates tty->receive_room
_after_ calling check_unthrottle. That means that the driver->write
call in ppp_async_process() returns 0. That would be fine if we were
going to get a subsequent wakeup call, but we aren't (we just had it,
and the buffer is now empty).
The solution is for n_tty.c to update tty->receive_room _before_
calling the driver unthrottle routine. The patch below does this.
With this patch I was able to transfer a 900MB file over a PPTP
connection (taking about 25 minutes), whereas without the patch the
connection would always stall in under a minute.
Signed-off-by: Paul Mackerras <paulus@samba.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bug fix: mv_eng_timeout() calls mv_err_intr() without first grabbing the host lock,
which can lead to all sorts of interesting scenarios.
This whole error-handling portion of sata_mv is nasty (and will get fixed for
the new EH stuff), but for now this patch will help keep it on life-support.
Signed-off-by: Mark Lord <liml@rtr.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Dave Jones [Wed, 19 Apr 2006 04:06:51 +0000 (21:06 -0700)]
[PATCH] PCI: Improve PCI config space writeback
At least one laptop blew up on resume from suspend with a black screen due
to a lack of this patch. By only writing back config space that is
different, we minimise the possibility of accidents like this.
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Jean Delvare [Tue, 18 Apr 2006 12:49:56 +0000 (14:49 +0200)]
[PATCH] PCI: Error handling on PCI device resume
We currently don't handle errors properly when resuming a PCI device:
* In pci_default_resume() we capture the error code returned by
pci_enable_device() but don't pass it up to the caller.
Introduced by commit 95a629657dbe28e44a312c47815b3dc3f1ce0970
* In pci_resume_device(), the errors possibly returned by the driver's
.resume method or by the generic pci_default_resume() function are
ignored.
This patch fixes both issues.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Krzysztof Helt [Sun, 11 Jun 2006 05:03:43 +0000 (22:03 -0700)]
[SPARC]: Migration cost tune up in sparc smp.
This patch sets the max_cache_size value required to tune up
scheduler in SMP systems. Otherwise, the calculated
migration_cost is too high and task scheduling may lock up.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Avoid JBUS errors on some Niagara systems.
[FUSION]: Fix mptspi.c build with CONFIG_PM not set.
[TG3]: Handle Sun onboard tg3 chips more correctly.
[SPARC64]: Dump local cpu registers in sun4v_log_error()
Milton Miller [Sat, 10 Jun 2006 16:54:16 +0000 (09:54 -0700)]
[PATCH] powerpc: console_initcall ordering issues
From: Milton Miller <miltonm@bga.com>
The add_preferred_console call in rtas_console.c was not causing the
console to be selected. It turns out that the add_preferred_console was
being called after the hvc_console driver was registered. It only works
when it is called before the console driver is registered.
Reorder hvc_console.o after the hvc_console drivers to allow the selection
during console_initcall processing.
Signed-off-by: Milton Miller <miltonm@bga.com> Signed-off-by: Anton Blanchard <anton@samba.org> Cc: Paul Mackerras <paulus@samba.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David Howells [Sat, 10 Jun 2006 16:54:12 +0000 (09:54 -0700)]
[PATCH] Further alterations for memory barrier document
From: David Howells <dhowells@redhat.com>
Apply some alterations to the memory barrier document that I worked out
with Paul McKenney of IBM, plus some of the alterations suggested by Alan
Stern.
The following changes were made:
(*) One of the examples given for what can happen with overlapping memory
barriers was wrong.
(*) The description of general memory barriers said that a general barrier is
a combination of a read barrier and a write barrier. This isn't entirely
true: it implies both, but is more than a combination of both.
(*) The first example in the "SMP Barrier Pairing" section was wrong: the
loads around the read barrier need to touch the memory locations in the
opposite order to the stores around the write barrier.
(*) Added a note to make explicit that the loads should be in reverse order to
the stores.
(*) Adjusted the diagrams in the "Examples Of Memory Barrier Sequences"
section to make them clearer. Added a couple of diagrams to make it more
clear as to how it could go wrong without the barrier.
(*) Added a section on memory speculation.
(*) Dropped any references to memory allocation routines doing memory
barriers. They may do sometimes, but it can't be relied on. This may be
worthy of further documentation later.
(*) Made the fact that a LOCK followed by an UNLOCK should not be considered a
full memory barrier more explicit and gave an example.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Paul E. McKenney <paulmck@us.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
David S. Miller [Sat, 10 Jun 2006 08:06:25 +0000 (01:06 -0700)]
[SPARC64]: Avoid JBUS errors on some Niagara systems.
Doing PCI config space accesses to non-present PCI slots
can result in fatal JBUS errors if the PCI config access
hypervisor call is performed on cpus other than the boot
cpu.
PCI config space accesses to present PCI slots works just
fine.
Recursively traverse the OBP device tree under the PCI
controller node and record all present device IDs into
a small hash table.
Avoid the hypervisor call for any PCI config space access
attempt for a device not recorded in the hash table.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 9 Jun 2006 18:58:36 +0000 (11:58 -0700)]
[TG3]: Handle Sun onboard tg3 chips more correctly.
Get rid of all the SUN_570X logic and instead:
1) Make sure MEMARB_ENABLE is set when we probe the SRAM
for config information. If that is off we will get
timeouts.
2) Always try to sync with the firmware, if there is no
firmware running do not treat it as an error and instead
just report it the first time we notice this condition.
3) If there is no valid SRAM signature, assume the device
is onboard by setting TG3_FLAG_EEPROM_WRITE_PROT.
Update driver version and release date.
With help from Michael Chan and Fabio Massimo Di Nitto.
Signed-off-by: David S. Miller <davem@davemloft.net>
Arnd Bergmann [Wed, 7 Jun 2006 02:04:18 +0000 (12:04 +1000)]
[PATCH] powerpc: Fix cell blade detection
The IBM Cell blade firmware might confuse the kernel to think it's a
pSeries machine. This fixes it for now. With a bit of luck, the firmware
will be updated to avoid that in the future but currently that patch is
needed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
[PATCH] powerpc: Fix call to ibm,client-architecture-support
The code in prom_init.c calling the firmware
ibm,client-architecture-support method on pSeries has a bug where it
fails to properly pass the instance handle of the firmware object when
trying to call a method. Result ranges from the call doing nothing to
the firmware crashing. (Found by Segher, thanks !)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Fri, 9 Jun 2006 03:02:59 +0000 (13:02 +1000)]
powerpc: Fix machine check problem on 32-bit kernels
This fixes a bug found by Dave Jones that means that it is possible
for userspace to provoke a machine check on 32-bit kernels. This
also fixes a couple of other places where I found similar problems
by inspection.
__futex_atomic_op needs to do an atomic operation in the user address space,
not the kernel address space. Add the missing sacf 256/sacf 0 to switch to
the secondary mode before doing the compare-and-swap. In addition add
another fixup for catch specification exceptions if the compare-and-swap
address is not aligned.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jens Axboe [Thu, 8 Jun 2006 08:26:39 +0000 (10:26 +0200)]
[PATCH] debugfs inode leak
Looking at the reiser4 crash, I found a leak in debugfs. In
debugfs_mknod(), we create the inode before checking if the dentry
already has one attached. We don't free it if that is the case.
These bugs happen quite often, I'm starting to think we should disallow
such coding in CodingStyle.
Jens Axboe [Thu, 8 Jun 2006 06:49:06 +0000 (08:49 +0200)]
[PATCH] elevator switching race
There's a race between shutting down one io scheduler and firing up the
next, in which a new io could enter and cause the io scheduler to be
invoked with bad or NULL data.
To fix this, we need to maintain the queue lock for a bit longer.
Unfortunately we cannot do that, since the elevator init requires to be
run without the lock held. This isn't easily fixable, without also
changing the mempool API. So split the initialization into two parts,
and alloc-init operation and an attach operation. Then we can
preallocate the io scheduler and related structures, and run the attach
inside the lock after we detach the old one.
This patch has survived 30 minutes of 1 second io scheduler switching
with a very busy io load.
Malcom Parsons [Thu, 8 Jun 2006 07:43:42 +0000 (00:43 -0700)]
[PATCH] fbcon: fix limited scroll in SCROLL_PAN_REDRAW mode
From: Malcom Parsons <malcolm.parsons@gmail.com>
When scrolling up in SCROLL_PAN_REDRAW mode with a large limited scroll
region, the bottom few lines have to be redrawn. Without this patch, the
wrong text is drawn into these lines, corrupting the display.
Observed in 2.6.14 when running an IRC client in the Nintendo DS linux
port.
I haven't tested if scrolling down has the same problem.
Ralf Baechle [Thu, 8 Jun 2006 07:43:41 +0000 (00:43 -0700)]
[PATCH] Fix mempolicy.h build error
From: Ralf Baechle <ralf@linux-mips.org>
<linux/mempolicy.h> uses struct mm_struct and relies on a definition or
declaration somehow magically being dragged in which may result in a
build:
[...]
CC mm/mempolicy.o
In file included from mm/mempolicy.c:69:
include/linux/mempolicy.h:150: warning: â\80\98struct mm_structâ\80\99 declared inside parameter list
include/linux/mempolicy.h:150: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/mempolicy.h:175: warning: â\80\98struct mm_structâ\80\99 declared inside parameter list
mm/mempolicy.c:622: error: conflicting types for â\80\98do_migrate_pagesâ\80\99
include/linux/mempolicy.h:175: error: previous declaration of â\80\98do_migrate_pagesâ\80\99 was here
mm/mempolicy.c:1661: error: conflicting types for â\80\98mpol_rebind_mmâ\80\99
include/linux/mempolicy.h:150: error: previous declaration of â\80\98mpol_rebind_mmâ\80\99 was here
make[1]: *** [mm/mempolicy.o] Error 1
make: *** [mm] Error 2
[ralf@denk linux-ip35]$
Including <linux/sched.h> is a step into direction of include hell so
fixed by adding a forward declaration of struct mm_struct instead.
The recent renaming of m48t86's ->readb() and ->writeb() platform driver
methods (2d7b20c1884777e66009be1a533641c19c4705f6) to ->readbyte() and
->writebyte() to fix the ia64 build broke the build of the cirrus ep93xx
ARM platform. This patch fixes it up.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org> Cc: Alessandro Zummo <a.zummo@towertech.it> Cc: Russell King <rmk@arm.linux.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Andy Currid [Thu, 8 Jun 2006 07:43:39 +0000 (00:43 -0700)]
[PATCH] Fix HPET operation on 64-bit NVIDIA platforms
From: "Andy Currid" <ACurrid@nvidia.com>
This patch fixes a kernel panic during boot that occurs on NVIDIA platforms
that have HPET enabled.
When HPET is enabled, the standard timer IRQ is routed to IOAPIC pin 2 and is
advertised as such in the ACPI APIC table - but an earlier workaround in the
kernel was ignoring this override. The fix is to honor timer IRQ overrides
from ACPI when HPET is detected on an NVIDIA platform.
Andy Currid [Thu, 8 Jun 2006 07:43:38 +0000 (00:43 -0700)]
[PATCH] Fix HPET operation on 32-bit NVIDIA platforms
From: "Andy Currid" <ACurrid@nvidia.com>
This patch fixes a kernel panic during boot that occurs on NVIDIA platforms
that have HPET enabled.
When HPET is enabled, the standard timer IRQ is routed to IOAPIC pin 2 and is
advertised as such in the ACPI APIC table - but an earlier workaround in the
kernel was ignoring this override. The fix is to honor timer IRQ overrides
from ACPI when HPET is detected on an NVIDIA platform.
Auke Kok [Thu, 8 Jun 2006 16:28:47 +0000 (09:28 -0700)]
e1000: remove risky prefetch on next_skb->data
It was brought to our attention that the prefetches break e1000 traffic
on xscale/arm architectures. Remove them for now. We'll let them
stay in mm for a while, or find a better solution to enable.
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[BRIDGE]: fix locking and memory leak in br_add_bridge
[IRDA]: Missing allocation result check in irlap_change_speed().
[PPPOE]: Missing result check in __pppoe_xmit().
[NET]: Eliminate unused /proc/sys/net/ethernet
[NETCONSOLE]: Clean up initcall warning.
[TCP]: Avoid skb_pull if possible when trimming head
Jiri Benc [Mon, 5 Jun 2006 23:39:34 +0000 (16:39 -0700)]
[BRIDGE]: fix locking and memory leak in br_add_bridge
There are several bugs in error handling in br_add_bridge:
- when dev_alloc_name fails, allocated net_device is not freed
- unregister_netdev is called when rtnl lock is held
- free_netdev is called before netdev_run_todo has a chance to be run after
unregistering net_device
Signed-off-by: Jiri Benc <jbenc@suse.cz> Signed-off-by: Stephen Hemminger <shemminger@osdl.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Chad Reese [Wed, 31 May 2006 00:16:49 +0000 (17:16 -0700)]
[MIPS] Fix sparsemem support.
Move memory_present() in arch/mips/kernel/setup.c. When using sparsemem
extreme, this function does an allocate for bootmem. This would always
fail since init_bootmem hasn't been called yet.
Move memory_present after free_bootmem. This only marks actual memory
ranges as present instead of the entire address space.
Signed-off-by: Chad Reese <creese@caviumnetworks.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix following warnings:
linux/arch/mips/kernel/setup.c:432: warning: field width is not type int (arg 2)
linux/arch/mips/kernel/setup.c:432: warning: field width is not type int (arg 4)
linux/arch/mips/kernel/syscall.c:279: warning: unused variable `len'
linux/arch/mips/kernel/syscall.c:280: warning: unused variable `name'
linux/arch/mips/math-emu/dp_fint.c:32: warning: unused variable `xc'
linux/arch/mips/math-emu/dp_flong.c:32: warning: unused variable `xc'
linux/arch/mips/math-emu/sp_fint.c:32: warning: unused variable `xc'
linux/arch/mips/math-emu/sp_flong.c:32: warning: unused variable `xc'
(original patch by Atsushi, slight changes to the setup.c part by me.)
Atsushi Nemoto [Wed, 31 May 2006 16:00:39 +0000 (01:00 +0900)]
[MIPS] Fix sparse warnings about too big constants.
Fix following warnings:
linux/arch/mips/kernel/setup.c:249:12: warning: constant 0xffffffff00000000 is so big it is unsigned long
linux/arch/mips/kernel/cpu-bugs64.c:209:10: warning: constant 0xffffffffffffdb9a is so big it is unsigned long
linux/arch/mips/kernel/cpu-bugs64.c:227:10: warning: constant 0xffffffffffffdb9a is so big it is unsigned long
linux/arch/mips/kernel/cpu-bugs64.c:283:10: warning: constant 0xffffffffffffdb9a is so big it is unsigned long
linux/arch/mips/kernel/cpu-bugs64.c:299:10: warning: constant 0xffffffffffffdb9a is so big it is unsigned long
Sergei Shtylyov [Sat, 27 May 2006 18:39:39 +0000 (22:39 +0400)]
[MIPS] Fix non-linear memory mapping on MIPS
Fix the non-linear memory mapping done via remap_file_pages() -- it
didn't work on any MIPS CPU because the page offset clashing with
_PAGE_FILE and some other page protection bits which should have been left
zeros for this kind of pages.
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com> Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sergei Shtylyov [Sat, 27 May 2006 19:36:41 +0000 (23:36 +0400)]
[MIPS] Au1xx0: fix prom_getenv() to handle YAMON style environment
Alchemy boards use YAMON which passes the environment variables as the
tuples of strings (the name followed by the value) unlike PMON which
passes "name=<val>" strings.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sergei Shtylyov [Sat, 27 May 2006 16:43:04 +0000 (20:43 +0400)]
[MIPS] Fix swap entry for MIPS32 36-bit physical address
With 64-bit physical address enabled, 'swapon' was causing kernel oops on
Alchemy CPUs (MIPS32) because of the swap entry type field corrupting the
_PAGE_FILE bit in 'pte_low' field. So, switch to storing the swap entry in
'pte_high' field using all its bits except _PAGE_GLOBAL and _PAGE_VALID which
gives 25 bits for the swap entry offset.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Sergei Shtylyov [Fri, 26 May 2006 15:44:54 +0000 (19:44 +0400)]
[MIPS] Save write-only Config.OD from being clobbered
Save the Config.OD bit from being clobbered by coherency_setup(). This
bit, when set, fixes various errata in the early steppings of Au1x00
SOCs. Unfortunately, the bit was write-only on the most early of them.
In addition, also restore the bit after a wakeup from sleep.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Atsushi Nemoto [Tue, 23 May 2006 07:42:38 +0000 (16:42 +0900)]
[MIPS] Fix modpost warning: Rename op_model_xxx to op_model_xxx_ops.
The modpost uses a whitelist for commonly used suffix on checking the
section mismatch. Adding "_ops" suffix to op_modex_xxx get rid of
this modpost warning.
WARNING: arch/mips/oprofile/oprofile.o - Section mismatch: reference to .init.text: from .data after 'op_model_mipsxx' (at offset 0x528)
[TCP]: Avoid skb_pull if possible when trimming head
Trimming the head of an skb by calling skb_pull can cause the packet
to become unaligned if the length pulled is odd. Since the length is
entirely arbitrary for a FIN packet carrying data, this is actually
quite common.
Unaligned data is not the end of the world, but we should avoid it if
it's easily done. In this case it is trivial. Since we're discarding
all of the head data it doesn't matter whether we move skb->data forward
or back.
However, it is still possible to have unaligned skb->data in general.
So network drivers should be prepared to handle it instead of crashing.
This patch also adds an unlikely marking on len < headlen since partial
ACKs on head data are extremely rare in the wild. As the return value
of __pskb_trim_head is no longer ever NULL that has been removed.
Signed-off-by: Herbert Xu ~{PmV>HI~} <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/brodo/pcmcia-fixes-2.6:
[PATCH] pcmcia: fix zeroing of cm4000_cs.c data
[PATCH] pcmcia: missing pcmcia_get_socket() result check
Jeff Dike [Sun, 4 Jun 2006 09:51:49 +0000 (02:51 -0700)]
[PATCH] uml: add -ffreestanding to CFLAGS
From: Jeff Dike <jdike@addtoit.com>
This fixes the undefined reference to strcpy seen when building modules on
i386. Tracked down by Al Viro.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Sun, 4 Jun 2006 09:51:48 +0000 (02:51 -0700)]
[PATCH] uml: more __user annotations
From: Al Viro <viro@zeniv.linux.org.uk>
uml __user annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Sun, 4 Jun 2006 09:51:47 +0000 (02:51 -0700)]
[PATCH] uml: __user annotation in arch_prctl
From: Al Viro <viro@zeniv.linux.org.uk>
fix uml/amd64 prctl()
put_user() there should go to (long __user *)addr, not &addr
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Sun, 4 Jun 2006 09:51:47 +0000 (02:51 -0700)]
[PATCH] uml: fix a typo in do_uml_initcalls
From: Jeff Dike <jdike@addtoit.com>
We had a spurious semicolon somehow.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6 / log