Patrick McHardy [Sun, 6 Jul 2008 04:26:57 +0000 (21:26 -0700)]
vlan: Add GVRP support
Add GVRP support for dynamically registering VLANs with switches.
By default GVRP is disabled because we only support the applicant-only
participant model, which means it should not be enabled on vlans that
are members of a bridge. Since there is currently no way to cleanly
determine that, the user is responsible for enabling it.
The code is pretty small and low impact, its wrapped in a config
option though because it depends on the GARP implementation and
the STP core.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 6 Jul 2008 04:26:41 +0000 (21:26 -0700)]
vlan: Move device unregistration before lower dev cleanup
Move the unregister_netdevice() call for the VLAN device before cleanup
for the lower device. This is needed by GVRP so it can send a leave
message before the applicant on the lower device is cleaned up.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 6 Jul 2008 04:26:27 +0000 (21:26 -0700)]
vlan: Change vlan_dev_set_vlan_flag() to handle multiple flags at once
Change vlan_dev_set_vlan_flag() to handle multiple flags at once and
rename to vlan_dev_change_flags(). This allows to to use it from the
netlink interface, which in turn allows to handle necessary adjustments
when changing flags centrally.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 6 Jul 2008 04:26:13 +0000 (21:26 -0700)]
net: Add GARP applicant-only participant
Add an implementation of the GARP (Generic Attribute Registration Protocol)
applicant-only participant. This will be used by the following patch to
add GVRP support to the VLAN code.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Sun, 6 Jul 2008 04:25:39 +0000 (21:25 -0700)]
net: Add STP demux layer
Add small STP demux layer for demuxing STP PDUs based on MAC address.
This is needed to run both GARP and STP in parallel (or even load the
modules) since both use LLC_SAP_BSPAN.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Sun, 6 Jul 2008 04:18:48 +0000 (21:18 -0700)]
MIB: add struct net to UDP_INC_STATS_BH
Two special cases here - one is rxrpc - I put init_net there
explicitly, since we haven't touched this part yet. The second
place is in __udp4_lib_rcv - we already have a struct net there,
but I have to move its initialization above to make it ready
at the "drop" label.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Acked-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
dst cache is marked as expired on the per/namespace basis by previous
path. Right now we have to implement selective cache shrinking. This
procedure has been ported from older OpenVz codebase.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
flush delay is used as an external storage for net.ipv4.route.flush sysctl
entry. It is write-only.
The ctl_table->data for this entry is used once. Fix this case to point
to the stack to remove global variable. Do this to avoid additional
variable on struct net in the next patch.
Possible race (as it was before) accessing this local variable is removed
using flush_mutex.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Alan Cox [Fri, 4 Jul 2008 06:43:12 +0000 (23:43 -0700)]
8390: Split 8390 support into a pausing and a non pausing driver core
Only a few ISA controllers need the pausing version of the 8390 core
while PCMCIA, later ISA and PCI do not. More importantly the ISA delays
can break non ISA boxes so we must use a different build of 8390.c for
the two sets of controllers.
No changes since last time as all the points of concerns raised proved to
be invalid
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PJ Waskiewicz [Fri, 27 Jun 2008 18:00:39 +0000 (11:00 -0700)]
igb: add NAPI Rx queue support
Update the NAPI implementation to use the new napi_struct infrstructure.
This removes the need of multiple net_device structs to implement a
multiqueue NAPI.
Signed-off-by: PJ Waskiewicz <peter.p.waskiewicz.jr.@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Fri, 27 Jun 2008 18:00:29 +0000 (11:00 -0700)]
igb: fix init on 82575 with MNG enabled
This patch resolves an issue seen on 82575 adapters with managability
pass-thru enabled, which could cause the system to panic.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alexander Duyck [Fri, 27 Jun 2008 18:00:07 +0000 (11:00 -0700)]
igb: fix parameter options
Currently there are items in the driver to support parameters, but there
are no parameters being added to the driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pekka Enberg [Mon, 23 Jun 2008 11:36:56 +0000 (14:36 +0300)]
ipg: run-time configurable jumbo frame support
Make jumbo frame support configurable via ifconfig mtu option as suggested by
Stephen Hemminger.
Cc: Stephen Hemminger <stephen.hemminger@vyatta.com> Tested-by: Andrew Savchenko <Bircoph@list.ru> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pekka Enberg [Mon, 23 Jun 2008 11:36:35 +0000 (14:36 +0300)]
ipg: per-device max_rxframe_size
Add a ->max_rxframe member to struct ipg_nic_private and convert the users of
IPG_MAX_RXFRAME_SIZE to use it instead to enable per-device jumbo frame
configuration.
Tested-by: Andrew Savchenko <Bircoph@list.ru> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pekka Enberg [Mon, 23 Jun 2008 11:36:18 +0000 (14:36 +0300)]
ipg: per-device rxsupport_size
Add a ->max_rxframe member to struct ipg_nic_private and convert the users of
IPG_RXSUPPORT_SIZE to use it instead to enable per-device jumbo frame
configuration.
Tested-by: Andrew Savchenko <Bircoph@list.ru> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pekka Enberg [Mon, 23 Jun 2008 11:36:00 +0000 (14:36 +0300)]
ipg: per-device rxfrag_size
Add a ->max_rxframe member to struct ipg_nic_private and convert the users of
IPG_RXFRAG_SIZE to use it instead to enable per-device jumbo frame
configuration.
Tested-by: Andrew Savchenko <Bircoph@list.ru> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Pekka Enberg [Mon, 23 Jun 2008 11:35:16 +0000 (14:35 +0300)]
ipg: always compile in jumbo frame support
Add a ->is_jumbo boolean to struct ipg_nic_private and fix up
ipg_interrupt_handler() to call the jumbo frame version of ipg_nic_rx() if the
boolean is set to true. Also remove the JUMBO_FRAME #ifdefs so we can always
compile in support for jumbo frames.
Tested-by: Andrew Savchenko <Bircoph@list.ru> Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Rusty Russell [Thu, 3 Jul 2008 10:48:02 +0000 (03:48 -0700)]
tun: Allow GSO using virtio_net_hdr
Add a IFF_VNET_HDR flag. This uses the same ABI as virtio_net
(ie. prepending struct virtio_net_hdr to packets) to indicate GSO and
checksum information.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Max Krasnyansky <maxk@qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rusty Russell [Thu, 3 Jul 2008 10:46:16 +0000 (03:46 -0700)]
tun: TUNSETFEATURES to set gso features.
ethtool is useful for setting (some) device fields, but it's
root-only. Finer feature control is available through a tun-specific
ioctl.
(Includes Mark McLoughlin <markmc@redhat.com>'s fix to hold rtnl sem).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Max Krasnyansky <maxk@qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Rusty Russell [Thu, 3 Jul 2008 10:45:32 +0000 (03:45 -0700)]
tun: Interface to query tun/tap features.
The problem with introducing checksum offload and gso to tun is they
need to set dev->features to enable GSO and/or checksumming, which is
supposed to be done before register_netdevice(), ie. as part of
TUNSETIFF.
Unfortunately, TUNSETIFF has always just ignored flags it doesn't
understand, so there's no good way of detecting whether the kernel
supports new IFF_ flags.
This patch implements a TUNGETFEATURES ioctl which returns all the valid IFF
flags. It could be extended later to include other features.
int netfd = open("/dev/net/tun", O_RDWR);
if (netfd < 0)
err(1, "Opening /dev/net/tun");
if (ioctl(netfd, TUNGETFEATURES, &features) != 0) {
printf("Kernel does not support TUNGETFEATURES, guessing\n");
features = (IFF_TUN|IFF_TAP|IFF_NO_PI|IFF_ONE_QUEUE);
}
printf("Available features are: ");
for (i = 0; i < sizeof(known_flags)/sizeof(known_flags[0]); i++) {
if (features & known_flags[i].flag) {
features &= ~known_flags[i].flag;
printf("%s ", known_flags[i].name);
}
}
if (features)
printf("(UNKNOWN %#x)", features);
printf("\n");
return 0;
}
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> Acked-by: Max Krasnyansky <maxk@qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Wang Chen [Thu, 3 Jul 2008 04:13:30 +0000 (12:13 +0800)]
ipv6: Do cleanup for ip6_mr_init.
If do not do it, we will get following issues:
1. Leaving junks after inet6_init failing halfway.
2. Leaving proc and notifier junks after ipv6 modules unloading.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com> Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
ipv6 route: Prefer outgoing interface with source address assigned.
Outgoing interface is selected by the route decision if unspecified.
Let's prefer routes via interface(s) with the address assigned if we
have multiple routes with same cost.
With help from Naohiro Ooiwa <nooiwa@miraclelinux.com>.
ipv6 addrconf: add accept_dad sysctl to control DAD operation.
- If 0, disable DAD.
- If 1, perform DAD (default).
- If >1, perform DAD and disable IPv6 operation if DAD for MAC-based
link-local address has been failed (RFC4862 5.4.5).
We do not follow RFC4862 by default. Refer to the netdev thread entitled
"Linux IPv6 DAD not full conform to RFC 4862 ?"
http://www.spinics.net/lists/netdev/msg52027.html
ipv6: Do not assign non-valid address on interface.
Check the type of the address when adding a new one on interface.
- the unspecified address (::) is always disallowed (RFC4291 2.5.2)
- the loopback address is disallowed unless the interface is (one of)
loopback (RFC4291 2.5.3).
- multicast addresses are disallowed.
Socket options SCTP_GET_PEER_ADDR_OLD, SCTP_GET_PEER_ADDR_NUM_OLD,
SCTP_GET_LOCAL_ADDR_OLD, and SCTP_GET_PEER_LOCAL_ADDR_NUM_OLD
have been replaced by newer versions a since 2005. It's time
to officially deprecate them and schedule them for removal.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the sysctl values for icmp ratelimit to use milliseconds instead
of jiffies which is based on kernel configured HZ.
Internal kernel jiffies are not a proper unit for any userspace API.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Francois Romieu [Sun, 11 May 2008 12:51:00 +0000 (14:51 +0200)]
r8169: remove non-napi code
It will almost unavoidably cause some breakage but it
is long overdue.
The driver identification string has been updated, a
lost tabulation and some unused code have been removed.
Otherwise the code paths should stay the same.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Tobias Diedrich [Sat, 31 May 2008 23:20:05 +0000 (01:20 +0200)]
Fix forcedeth hibernate/wake-on-lan problems
This patch is the minimal amount of code needed to support
wake-on-lan in platform mode properly (i.e. "ethtool -s eth0 wol g"
is sufficient, no additional magic needed) for me.
This is derived from David Brownells patch
(http://lists.laptop.org/pipermail/devel/2007-April/004691.html).
However I decided to move the hook into pci-acpi.c since the other
two pci hooks also live there and pci and acpi are the only users of
the platform_enable_wakeup-hook.
As a 'side-effect' this also makes wake on usb activity work for me
and I had to disable usb wakeup (which is enabled by default) using
the power/wakeup sysfs functionality ("echo disabled >
${sysfs_path_to_device}/power/wakeup").
(BTW I first thought the 'immediate reboot because of usb wake' effect is
caused by the optical mouse generating a wake event, but it rather
seems to be a problem with a flaky secondary usb host controller,
which sees a connected device where nothing is attached)
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tobias Diedrich [Sat, 31 May 2008 22:54:42 +0000 (00:54 +0200)]
Fix forcedeth hibernate/wake-on-lan problems
We currently don't signal the kernel we that this device can wake
the system. Call device_init_wakeup() to correct this.
Without this device_can_wakeup and device_may_wakeup will return
incorrect values.
Together with the minimized acpi wakeup patch (6/4 ;)), which will
follow in the next mail, this really makes wake-on-lan work for me
as expected (i.e. "ethtool -s eth0 wol g" is sufficient, no
additional magic needed).
Signed-off-by: Tobias Diedrich <ranma+kernel@tdiedrich.de> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Márton Németh [Sun, 15 Jun 2008 07:52:30 +0000 (09:52 +0200)]
8139too: some style cleanups
Clean up the following errors and warnings reported by checkpatch.pl:
+ ERROR: Macros with complex values should be enclosed in parenthesis
+ WARNING: __func__ should be used instead of gcc specific __FUNCTION__
+ WARNING: plain inline is preferred over __inline__
+ WARNING: Use #include <linux/io.h> instead of <asm/io.h>
+ WARNING: Use #include <linux/uaccess.h> instead of <asm/uaccess.h>
The changes were verified with by comparing the "objdump -d 8139too.ko"
output which is exactly the same for the old and new version in case of
config CONFIG_8139TOO=m, CONFIG_8139TOO_PIO=n, CONFIG_8139TOO_TUNE_TWISTER=n,
CONFIG_8139TOO_8129=n, CONFIG_8139_OLD_RX_RESET=n.
Software versions used: gcc 4.2.3, objdump 2.18.0.20080103, on elf32-i386.
Signed-off-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Andy Gospodarek [Thu, 19 Jun 2008 21:19:12 +0000 (17:19 -0400)]
e1000: remove e1000_clean_tx_irq call from e1000_netpoll
The call to e1000_clean_tx_irq in e1000_netpoll can race with the call
to e1000_clean_tx_irq in e1000_clean. With a small bit of tweaking to
to netpoll_send_skb to simulate a system that was under extreme stress,
I was able to reproduce these concurrent calls. This can result in
multiple frees to the skbs on the tx ring buffer.
Dropping this call from e1000_netpoll should be fine since we can rely
on the calls in e1000_clean to do what is needed since napi will poll
the hardware just after calling poll_controller.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Taku Izumi [Fri, 20 Jun 2008 03:10:30 +0000 (12:10 +0900)]
igb: make ioport free
This patch makes igb driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Taku Izumi [Fri, 20 Jun 2008 02:57:02 +0000 (11:57 +0900)]
e1000e: make ioport free
This patch makes e1000e driver ioport-free.
This corrects behavior in probe function so as not to request ioport
resources as long as they are not really needed.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Auke Kok [Sun, 22 Jun 2008 22:21:29 +0000 (15:21 -0700)]
e1000: remove PCI Express device IDs
We do not want to prolong the situation much longer that e1000
and e1000e support these devices at the same time. As a result,
take out the bandage that was added for the interim period
and remove all the PCI Express device IDs from e1000.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ipv6 route: Convert rt6_device_match() to use RT6_LOOKUP_F_xxx flags.
The commit 77d16f450ae0452d7d4b009f78debb1294fb435c ("[IPV6] ROUTE:
Unify RT6_F_xxx and RT6_SELECT_F_xxx flags") intended to pass various
routing lookup hints around RT6_LOOKUP_F_xxx flags, but conversion was
missing for rt6_device_match().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore [Sat, 28 Jun 2008 03:12:32 +0000 (20:12 -0700)]
netlabel: Fix a problem when dumping the default IPv6 static labels
There is a missing "!" in a conditional statement which is causing entries to
be skipped when dumping the default IPv6 static label entries. This can be
demonstrated by running the following:
... you will notice that the entry for the IPv6 localhost address is not
displayed but does exist (works correctly, causes collisions when attempting
to add duplicate entries, etc.).
Signed-off-by: Paul Moore <paul.moore@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Eli Cohen [Sat, 28 Jun 2008 03:09:00 +0000 (20:09 -0700)]
net/inet_lro: remove setting skb->ip_summed when not LRO-able
When an SKB cannot be chained to a session, the current code attempts
to "restore" its ip_summed field from lro_mgr->ip_summed. However,
lro_mgr->ip_summed does not hold the original value; in fact, we'd
better not touch skb->ip_summed since it is not modified by the code
in the path leading to a failure to chain it. Also use a cleaer
comment to the describe the ip_summed field of struct net_lro_mgr.
Issue raised by Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Emelyanov [Sat, 28 Jun 2008 03:06:08 +0000 (20:06 -0700)]
inet fragments: fix race between inet_frag_find and inet_frag_secret_rebuild
The problem is that while we work w/o the inet_frags.lock even
read-locked the secret rebuild timer may occur (on another CPU, since
BHs are still disabled in the inet_frag_find) and change the rnd seed
for ipv4/6 fragments.
It was caused by my patch fd9e63544cac30a34c951f0ec958038f0529e244
([INET]: Omit double hash calculations in xxx_frag_intern) late
in the 2.6.24 kernel, so this should probably be queued to -stable.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Li Zefan [Sat, 28 Jun 2008 03:03:24 +0000 (20:03 -0700)]
CONNECTOR: add a proc entry to list connectors
I got a problem when I wanted to check if the kernel supports process
event connector, and It seems there's no way to do this check.
At best I can check if the kernel supports connector or not, by looking
into /proc/net/netlink, or maybe checking the return value of bind() to
see if it's ENOENT.
So it would be useful to add /proc/net/connector to list all supported
connectors:
# cat /proc/net/connector
Name ID
connector 4294967295:4294967295
cn_proc 1:1
w1 3:1
Changelog:
- fix memory leak: s/seq_release/single_release
- use spin_lock_bh instead of spin_lock_irqsave
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Adrian Bunk [Sat, 28 Jun 2008 02:54:05 +0000 (19:54 -0700)]
pkt_sched: Remove CONFIG_NET_SCH_RR
Commit d62733c8e437fdb58325617c4b3331769ba82d70
([SCHED]: Qdisc changes and sch_rr added for multiqueue)
added a NET_SCH_RR option that was unused since the code
went unconditionally into sch_prio.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca> Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Rainer Weikusat [Sat, 28 Jun 2008 02:34:18 +0000 (19:34 -0700)]
af_unix: fix 'poll for write'/connected DGRAM sockets
For n:1 'datagram connections' (eg /dev/log), the unix_dgram_sendmsg
routine implements a form of receiver-imposed flow control by
comparing the length of the receive queue of the 'peer socket' with
the max_ack_backlog value stored in the corresponding sock structure,
either blocking the thread which caused the send-routine to be called
or returning EAGAIN. This routine is used by both SOCK_DGRAM and
SOCK_SEQPACKET sockets. The poll-implementation for these socket types
is datagram_poll from core/datagram.c. A socket is deemed to be
writeable by this routine when the memory presently consumed by
datagrams owned by it is less than the configured socket send buffer
size. This is always wrong for PF_UNIX non-stream sockets connected to
server sockets dealing with (potentially) multiple clients if the
abovementioned receive queue is currently considered to be full.
'poll' will then return, indicating that the socket is writeable, but
a subsequent write result in EAGAIN, effectively causing an (usual)
application to 'poll for writeability by repeated send request with
O_NONBLOCK set' until it has consumed its time quantum.
The change below uses a suitably modified variant of the datagram_poll
routines for both type of PF_UNIX sockets, which tests if the
recv-queue of the peer a socket is connected to is presently
considered to be 'full' as part of the 'is this socket
writeable'-checking code. The socket being polled is additionally
put onto the peer_wait wait queue associated with its peer, because the
unix_dgram_recvmsg routine does a wake up on this queue after a
datagram was received and the 'other wakeup call' is done implicitly
as part of skb destruction, meaning, a process blocked in poll
because of a full peer receive queue could otherwise sleep forever
if no datagram owned by its socket was already sitting on this queue.
Among this change is a small (inline) helper routine named
'unix_recvq_full', which consolidates the actual testing code (in three
different places) into a single location.
Signed-off-by: Rainer Weikusat <rweikusat@mssgmbh.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Octavian Purdila [Sat, 28 Jun 2008 00:27:21 +0000 (17:27 -0700)]
tcp: fix for splice receive when used with software LRO
If an skb has nr_frags set to zero but its frag_list is not empty (as
it can happen if software LRO is enabled), and a previous
tcp_read_sock has consumed the linear part of the skb, then
__skb_splice_bits:
(a) incorrectly reports an error and
(b) forgets to update the offset to account for the linear part
Any of the two problems will cause the subsequent __skb_splice_bits
call (the one that handles the frag_list skbs) to either skip data,
or, if the unadjusted offset is greater then the size of the next skb
in the frag_list, make tcp_splice_read loop forever.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
tcp: calculate tcp_mem based on low memory instead of all memory
The tcp_mem array which contains limits on the total amount of memory
used by TCP sockets is calculated based on nr_all_pages. On a 32 bits
x86 system, we should base this on the number of lowmem pages.
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211: fix an oops in several failure paths in key allocation
This patch fixes an oops in several failure paths in key allocation. This
Oops occurs when freeing a key that has not been linked yet, so the
key->sdata is not set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Wed, 25 Jun 2008 19:27:00 +0000 (21:27 +0200)]
rt2x00: Fix lock dependency errror
This fixes a circular locking dependency in the workqueue handling.
The interface work task uses the mac80211 function
ieee80211_iterate_active_interfaces() which grabs the RTNL lock.
However when the interface is brough down, this happens under the RTNL
lock as well, this causes problems because mac80211 will flush the workqueue
during the ifdown event. This causes mac80211 to wait until the driver has
completed all work which can't finish because it is waiting on the RTNL lock.
This is fixed by moving rt2x00 workqueue tasks on a different workqueue,
this workqueue can be flushed when the ieee80211_hw structure is removed
by the driver (when the driver is unloaded) which does not happen under the
RTNL lock.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/b43/rfkill.o
drivers/net/wireless/b43/rfkill.c: In function ‘b43_rfkill_soft_toggle’:
drivers/net/wireless/b43/rfkill.c:90: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch
CC [M] drivers/net/wireless/b43legacy/rfkill.o
drivers/net/wireless/b43legacy/rfkill.c: In function ‘b43legacy_rfkill_soft_toggle’:
drivers/net/wireless/b43legacy/rfkill.c:92: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch
CC [M] drivers/net/wireless/iwlwifi/iwl-rfkill.o
drivers/net/wireless/iwlwifi/iwl-rfkill.c: In function ‘iwl_rfkill_soft_rf_kill’:
drivers/net/wireless/iwlwifi/iwl-rfkill.c:56: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch
Also handle RFKILL_STATE_{ON,OFF} -> RFKILL_STATE_{UNBLOCKED,SOFT_BLOCKED}
conversion since I'm already here...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Fri, 27 Jun 2008 13:31:29 +0000 (09:31 -0400)]
ath5k: remove now unused variable declared in ath5k_tx
CC [M] drivers/net/wireless/ath5k/base.o
drivers/net/wireless/ath5k/base.c: In function ‘ath5k_tx’:
drivers/net/wireless/ath5k/base.c:2598: warning: unused variable ‘info’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Wed, 25 Jun 2008 11:36:27 +0000 (14:36 +0300)]
mac80211: fix tx fragmentation
This patch fixes TX fragmentation caused by
tx handlers reordering and 'tx info to cb' patches
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 26 Jun 2008 17:59:56 +0000 (19:59 +0200)]
mac80211: make workqueue freezable
This patch makes the mac80211 workqueue freezable making it
interact a bit better with system suspend and not try to ping
the AP while the hardware is down.
This doesn't really help with implementing proper suspend in
any way but makes some bad things trigger less.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Randy Dunlap [Wed, 25 Jun 2008 04:02:46 +0000 (21:02 -0700)]
iwlwifi: fix build for CONFIG_INPUT=n
Fix iwlwifi so that it builds cleanly with CONFIG_INPUT=n.
Also free the input device on exit.
drivers/built-in.o: In function `iwl_rfkill_unregister':
(.text+0xbf430): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `iwl_rfkill_init':
(.text+0xbf51c): undefined reference to `input_allocate_device'
drivers/built-in.o: In function `iwl_rfkill_init':
(.text+0xbf5bf): undefined reference to `input_register_device'
drivers/built-in.o: In function `iwl_rfkill_init':
(.text+0xbf5e9): undefined reference to `input_free_device'
net/built-in.o: In function `rfkill_disconnect':
rfkill-input.c:(.text+0xe71e1): undefined reference to `input_close_device'
rfkill-input.c:(.text+0xe71e9): undefined reference to `input_unregister_handle'
net/built-in.o: In function `rfkill_connect':
rfkill-input.c:(.text+0xe723e): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0xe724d): undefined reference to `input_open_device'
rfkill-input.c:(.text+0xe725c): undefined reference to `input_unregister_handle'
net/built-in.o: In function `rfkill_handler_init':
rfkill-input.c:(.init.text+0x36ec): undefined reference to `input_register_handler'
net/built-in.o: In function `rfkill_handler_exit':
rfkill-input.c:(.exit.text+0x112c): undefined reference to `input_unregister_handler'
make[1]: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 24 Jun 2008 17:23:36 +0000 (19:23 +0200)]
mac80211: Add RTNL warning for workqueue
The workqueue provided by mac80211 should not be used for
scheduled tasks that acquire the RTNL lock. This could be done
when the driver uses the function ieee80211_iterate_active_interfaces()
within the scheduled work. Such behavior will end in locking
dependencies problems when an interface is being removed.
This patch will add a notification about the RTNL locking and
the mac80211 workqueue to prevent driver developers from
blindly using it.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the authentication method upon giwencode ioctl.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: don't return -EINVAL upon iwconfig wlan0 rts auto
This patch avoids returning -EINVAL upon iwconfig wlan0 rts auto. If
rts->fixed is 0, then we should choose a default value instead of failing.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
projects / linux-2.6 / log