Hannes Reinecke [Fri, 20 Oct 2006 07:58:47 +0000 (09:58 +0200)]
[SCSI] scsi_debug: support REPORT TARGET PORT GROUPS
This patch adds support for REPORT TARGET PORT GROUPS. This is used
eg for the multipathing priority callout to determine the path
priority.
With this patch multipath-tools can use the existing mpath_prio_alua
callout to exercise the path priority grouping.
Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Douglas Gilbert <dougg@torque.net> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Mon, 16 Oct 2006 22:09:42 +0000 (18:09 -0400)]
[SCSI] libiscsi: fix logout pdu processing
According to the iscsi RFC, we cannot send other requests if
we have sent a logout pdu. This patch enforces this requirement
by blocking the session and suspending the send thread. Userspace
decides if we restart the connection or if we just free everything.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Mon, 16 Oct 2006 22:09:40 +0000 (18:09 -0400)]
[SCSI] libiscsi: fix missed iscsi_task_put in xmit error path
from bhalevy@gmail.com:
It looks like change 652 to libiscsi.c added some dead code around line
670
if (rc) {
spin_unlock_bh(&conn->session->lock);
goto again;
}
since 5 lines above we goto again if (rc).
It looks like the previous if (rc) should go away if we want to put the
ctask before
breaking out of the while loop with "goto again" (see following patch).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Mon, 16 Oct 2006 22:09:39 +0000 (18:09 -0400)]
[SCSI] libiscsi: fix oops in connection create failure path
If connection creation fails we end up calling list_del
on a invalid struct. This then causes an oops. We are not
acutally using the lists (old MCS code we thought might
be useful elsewhere) so this patch just removes that
code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Christie [Mon, 16 Oct 2006 22:09:38 +0000 (18:09 -0400)]
[SCSI] iscsi class: fix slab corruption during restart
The transport class recv mempools are causing slab corruption.
We could hack around netlink's lack of mempool support like dm,
but it is just too ulgy (dm's hack is ugly enough :) when you need
to support broadcast.
This patch removes the recv pools. We have not used them even when
we were allocting 20 MB per session and the system only had 64 MBs.
And we have no pools on the send side and have been ok there. When
Peter's work gets merged we can use that since the network guys
are in favor of that approach and are not going to add mempools
everywhere.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Alan Cox [Mon, 16 Oct 2006 15:55:46 +0000 (16:55 +0100)]
[SCSI] Switch fdomain to the pci_get API
Doesn't make the hardware hot pluggable but does ensure the driver won't
crash when another device is hot-unplugged at the wrong moment. Soon I
propose to deprecate pci_find_device() and some of its friends.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It is known that 2 LSI Logic MegaRAID SATA RAID Controllers (150-4 and
150-6) don't support 64-bit DMA. Unfortunately currently this check is
wrong and driver sets 64-bit DMA mode for these devices.
Santiago Leon [Fri, 13 Oct 2006 15:22:50 +0000 (10:22 -0500)]
[SCSI] ibmvscsi: correctly reenable CRQ
The "ibmvscsi: treat busy and error conditions separately" patch
submitted by Dave Boutcher back in June incorrectly reenables the CRQ.
The broken logic causes the adapter to get disabled if the CRQ
connection happens to close temporarily. This patch "fixes that
obviously wrong logic check" (Dave's words).
Signed-off-by: Santiago Leon <santil@us.ibm.com> Signed-off-by: David Boutcher <sleddog@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Andrew Vasquez [Fri, 13 Oct 2006 16:33:39 +0000 (09:33 -0700)]
[SCSI] qla2xxx: Correct QUEUE_FULL handling.
- Drop queue-depths across all luns for a given fcport
during TASK_SET_FULL statuses.
- Ramp-up I/Os after throttling.
- Consolidate completion-status handling of CS_QUEUE_FULL with
CS_COMPLETE as ISP24xx firmware no longer reports
CS_QUEUE_FULL.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Early ISP2432 parts have a known hardware issue when coming
out of a D3 hot state. This issue can result in a hung PCIe
link. Recent firmwares contain a workaround whereby the
stop-firmware mailbox command prevents the ISP from entering
the D3 hot state.
In order to ensure that the workaround succeeded the driver
must verify that the stop-firmware mailbox command completes
successfully. In the event of a failure, the driver
attempts a shutdown-retry after resetting the ISP and
re-executing firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in the Fibre Channel
driver (fc4).
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete typedefd Scsi_Cmnd to struct scsi_cmnd in
the ninja scsi pcmcia driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in psi240i-driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Eric Sesterhenn [Tue, 10 Oct 2006 21:41:43 +0000 (14:41 -0700)]
[SCSI] lpfc: check before dereference in lpfc_ct.c
If we fail to allocate mp->virt during the first while loop iteration,
mlist is still uninitialized, therefore we should check if before
dereferencing.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Acked-by: James Smart <James.Smart@Emulex.Com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Henne [Mon, 9 Oct 2006 13:38:34 +0000 (15:38 +0200)]
[SCSI] fix typo in previous Scsi_Cmnd convertion in aic7xxx_old.c
Fixes a typo in the aic7xxx_old.c.
Signed-off-by: Olaf Hering <olaf@aepfle.de> Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Michael Reed [Fri, 6 Oct 2006 20:39:25 +0000 (15:39 -0500)]
[SCSI] mptfc: stall eh handlers if resetting while rport blocked
Thanks to James Smart for the inspiration.
Stall error handler if attempting recovery while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.
Also verify that VirtDevice is available before issuing scsi command.
VirtDevice is removed when fc transport removes a target.
See James Smart's patch of 08/17/2006 for greater detail.
AM53C974A's Start Transfer Counter register has 24 bits, thus
maximum transfer length is 16MiB. But the maximum I can test
is 8MiB, so use that until somebody tests 16MiB.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Linus Torvalds [Wed, 11 Oct 2006 00:14:44 +0000 (17:14 -0700)]
ACPI: Allow setting SCI_EN bit in PM1_CONTROL register
This is needed by at least the Mac Mini's, which (incorrectly) come back
from suspend with SCI_EN clear.
Thanks to Frédéric Riss for hunting this down.
Acked-by: Frédéric Riss <frederic.riss@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Cc: Len Brown <len.brown@intel.com> Cc: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Garzik [Tue, 10 Oct 2006 06:58:14 +0000 (02:58 -0400)]
[PATCH] firmware/dcdbas: fix bug in error cleanup
The error path path mistakenly called sysfs_create_group() rather than
sysfs_remove_group(). They take the same arguments, so it's easy to
cut-n-paste such a bug.
Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Garzik [Tue, 10 Oct 2006 05:40:55 +0000 (01:40 -0400)]
[PATCH] irda: donauboe fixes, cleanups
- fix: toshoboe_invalid_dev() was recently removed, but not all callers
were updated, causing the obvious linker error. Remove caller,
because the check (like the one removed) isn't used.
- fix: propagate request_irq() return value
- cleanup: remove void* casts
- cleanup: remove impossible ASSERTs
Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alexey Dobriyan [Wed, 28 Dec 2005 19:27:10 +0000 (22:27 +0300)]
[PATCH] Finish annotations of struct vlan_ethhdr
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Roland Dreier [Tue, 10 Oct 2006 19:50:38 +0000 (12:50 -0700)]
RDMA/amso1100: Fix build with debugging off
Since pr_debug() has changed from a macro to an inline function when
DEBUG is not defined, its arguments now need to be defined even when
debugging is off. Therefore to_event_str() and to_qp_state_str() need
to be moved out of #ifdef DEBUG. The compiler will throw the
definitions away if DEBUG is not defined, but it needs to be able to
see that the functions exist.
Sean Hefty [Wed, 4 Oct 2006 18:37:25 +0000 (11:37 -0700)]
IB/cm: Send DREP in response to unmatched DREQ
Currently a DREP is only sent in response to a DREQ if a connection
has been found matching the DREQ, and it is in the proper state. Once
a DREP is sent, the local connection moves into timewait. Duplicate
DREQs received while in this state result in re-sending the DREP.
However, it's likely that the local connection will enter and exit
timewait before the remote side times out a lost DREP and resends a DREQ.
To handle this, we send a DREP in response to a DREQ, even if a local
connection is not found. This avoids maintaining disconnected
id's in timewait states for excessively long times, just to handle a
lost DREP.
Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Sean Hefty [Wed, 4 Oct 2006 18:29:59 +0000 (11:29 -0700)]
IB/cm: Fix timewait crash after module unload
If the ib_cm module is unloaded while id's are still in timewait, the
CM will destroy the work queue used to process timewait. Once the
id's exit timewait, their timers will fire, leading to a crash trying
to access the destroyed work queue.
We need to track id's that are in timewait, and cancel their deferred
work on module unload.
Signed-off-by: Sean Hefty <sean.hefty@intel.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
IB/srp: Enable multiple connections to the same target
Enable multiple concurrent connections to the same SRP target:
1) Use port GUID instead of node GUID in the initiator port
identifier. This allows connections to be made from multiple HCA
ports at the same time.
2) Let the user specify the identifier extention when adding the
device. This allows userspace to make multiple connections even
from the same port, if it wants too.
Without this, only one connection can be made from any given HCA, even
if it has multiple ports, because we don't use multi-channel mode, so
targets will only allow one connection from a given initiator port ID.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il> Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Ishai Rabinovitz [Tue, 10 Oct 2006 16:51:14 +0000 (09:51 -0700)]
IB/srp: Remove redundant memset()
scsi_host_alloc() already allocates with kzalloc(), so the struct Scsi_Host
is zeroed out, including the private data portion. Remove the redundant
memset that zeros this out again in the SRP initiator.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Tom Tucker [Tue, 3 Oct 2006 14:46:41 +0000 (09:46 -0500)]
RDMA/amso1100: Add spinlocks to serialize ib_post_send/ib_post_recv
The AMSO driver was not thread-safe in the post WR code and had
code that would sleep if the WR post FIFO was full. Since these
functions can be called on interrupt level I changed the sleep to a
udelay.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com> Signed-off-by: Roland Dreier <rolandd@cisco.com>
The windfarm code uses a struct device_driver instead of
platform_driver, which can cause crashes if any of the callbacks are
called (like on module removal). This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
i2c-powermac was written & merged right after Russell King's changes
adding platform_driver... which I missed. Thus it still used struct
device, causing crashes when hitting sleep/wakeup callbacks (it happened
to work by luck so far, until early/late callbacks got added). This
causes crashes on sleep/wakeup on PowerBooks with 2.6.19. The patch
fixes it by using a proper platform_driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Paul Mackerras [Tue, 10 Oct 2006 03:51:00 +0000 (13:51 +1000)]
[POWERPC] Fix secondary CPU startup on old "powersurge" SMP powermacs
On the old "powersurge" SMP powermacs, the second CPU is started up
by sending it an IPI, which has the side effect of stopping the
timebase clock (so the secondary CPU's timebase can be synchronized
with the primary's). The routine that did this used udelay, which
will hang forever when the timebase is stopped, since udelay now spins
until the timebase reaches a certain value.
The end result is that the kernel would hang when bringing up the
second CPU. This fixes it by using a simple loop which just does a
fixed number of iterations to generate the delay. These old systems
were all clocked at around 200 MHz or so, so a fixed number of
iterations is acceptable.
projects / linux-2.6 / log