Randy Dunlap [Thu, 15 Nov 2007 00:52:25 +0000 (16:52 -0800)]
[SCSI] boot options: correct option name and tell where to find docs for it
Minor corrections and additions to 'scsi_logging_level', as pointed out
by Chuck Ebbert.
Also point out the IBM S390-tools 'scsi_logging_level' script.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tony Battersby [Mon, 12 Nov 2007 15:00:44 +0000 (10:00 -0500)]
[SCSI] move single_lun flag from scsi_device to scsi_target
Some SCSI tape medium changers that need the BLIST_SINGLELUN flag have
the medium changer at one LUN and the tape drive at a different LUN.
The inquiry string of the tape drive may be different from that of the
medium changer. In order for single_lun to be effective, every
scsi_device under a given scsi_target must have it set. This means that
there needs to be a blacklist entry for BOTH the medium changer AND the
tape drive, which is impractical because some medium changers may be
paired with a variety of different tape drive models. It makes more
sense to put the single_lun flag in scsi_target instead of scsi_device,
which causes every device at a given target ID to inherit the single_lun
flag from one LUN. This makes it possible to blacklist just the medium
changer and not the tape drive.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yang [Fri, 9 Nov 2007 09:40:16 +0000 (04:40 -0500)]
[SCSI] megaraid_sas: support for poll_mode_io (reduced interrupt)
Added module parameter "poll_mode_io" to support for "polling"
(reduced interrupt operation). In this mode, IO completion interrupts
are delayed. At the end of initiating IOs, the driver schedules for
cmd completion if there are pending cmds. A timer-based interrupt has
also been added to prevent IO completion from being delayed
indefinitely in the case that no new IOs are initiated. Some
formatting issues in resume, suspend comment block also corrected
Signed-off-by: Bo Yang <bo.yang@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
bo yang [Fri, 9 Nov 2007 09:14:00 +0000 (04:14 -0500)]
[SCSI] megaraid_sas: check max_sgl reported by FW for setting max_sectors_per_req
1. Setting the max_sectors_per_req based on max SGL supported by the
FW. Prior versions calculated this value from controller info's
max_sectors_1, max_sectors_2. For certain controllers/FW, this was
resulting in a value greater than max SGL supported by the FW. Now
we take the min of max sgl from FW and max_sectors calculation.
2. Increased MFI_POLL_TIMEOUT_SECS to 60 seconds from 10. FW may take
a max of 60 seconds to respond to the INIT cmd.
Signed-off-by: Bo Yang <bo.yang@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tony Battersby [Fri, 9 Nov 2007 18:04:35 +0000 (13:04 -0500)]
[SCSI] 3w-9xxx: fix abysmal write performance on some motherboards
The 3ware 9500S-8 SATA RAID controller exhibits terrible write
performance when PCI memory-write-and-invalidate is disabled. This is
easy to demonstrate by replacing pci_try_set_mwi() in the patch below
with pci_clear_mwi(). My benchmarks show the following:
Most motherboards will enable MWI without the driver having to set it
explicitly, so most people probably wouldn't encounter this problem.
For the few motherboards that don't enable it, this patch could give a
16x performance improvement for writing.
This issue does not seem to affect the 9550SX controller, but the patch
doesn't hurt it either. I haven't tested any of the other 3ware
controllers.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Acked-by: adam radford <aradford@gmail.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Darrick J. Wong [Mon, 5 Nov 2007 19:51:17 +0000 (11:51 -0800)]
[SCSI] libsas: Convert sas_proto users to sas_protocol
sparse complains about the mixing of enums in libsas. Since the
underlying numeric values of both enums are the same, combine them
to get rid of the warning.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[SCSI] megaraid_sas: Convert aen_mutex to the mutex API
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com> Acked-by: Bo Yang <Bo.Yang@lsi.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove tracing for request with a "qualifier" field set in the
response. The protocol status qualifier now contains measurement
data for "good" commands, so this check would trace every response
by default.
The fix is to simply remove the "qual" tracing: The responses with an
interesting status are also traced as "ferr" or "perr" and all
responses can be traced as "norm" with a higher trace level.
When adding an invalid LUN, there is a deadlock between the add
via scsi_scan_target and the slave_destroy handler: The handler
waits for the scan to complete, but for an invalid unit,
scsi_scan_target directly calls the slave_destroy handler.
Fix the deadlock by removing the wait in the slave_destroy
handler, it was not necessary anyway.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Swen Schillig <swen@vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[SCSI] zfcp: Remove SCSI devices when removing complete adapter
The common I/O layer can call remove a handler to inform zfcp
that a device disappeared. The handler zfcp_ccw_remove then
removes all unit, port and the adapter data structures. Removing
the units requires that the SCSI devices are removed first.
The callback function used by zfcp always returns success,
which is an indication for the SCSI midlayer to stop error
handling. Remove the bus_reset callback, since the same
function will be called via the host_reset callback.
Salyzyn, Mark [Tue, 30 Oct 2007 19:50:49 +0000 (15:50 -0400)]
[SCSI] aacraid: forced reset override
Some of our vendors have requested that our adapters ignore the hardware
reset attempts during recovery and have enforced this with changes in
Adapter Firmware. Some of our customers have requested the option to be
able to reset the adapter under adverse adapter failure, we even had a
few defects reported here considering it a regression that the Adapter
could not be reset. This patch addresses this dichotomy. The user can
force the adapter to be reset if it supports the IOP_RESET_ALWAYS
command, in cases where the adapter has been programmed to ignore the
reset, by setting the aacraid.check_reset parameter to a value of -1.
The driver will not reset an Adapter that does not support the reset
command(s).
This patch also fixes and cleans up some of the logic associated with
resetting the adapter.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James <James.Bottomley@HansenPartnership.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Boaz Harrosh [Mon, 5 Nov 2007 09:23:35 +0000 (11:23 +0200)]
[SCSI] NCR5380 family: convert to accessors & !use_sg cleanup
- This patch depends on:
NCR5380: Use scsi_eh API for REQUEST_SENSE invocation
- convert to accessors and !use_sg cleanup
- FIXME: Not sg-chain ready look for ++cmd->SCp.buffer
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James <James.Bottomley@HansenPartnership.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Boaz Harrosh [Mon, 5 Nov 2007 09:21:40 +0000 (11:21 +0200)]
[SCSI] wd7000: proper fix for boards without sg support
- code used to set sg_tablesize to zero for board revision
less than 6. This is no longer supported, therefore I
use sg_tablesize=1 and open code the sg handling for that case.
- Get rid of use of SG_NONE which will be removed soon.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James <James.Bottomley@HansenPartnership.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Boaz Harrosh [Wed, 22 Aug 2007 16:10:45 +0000 (19:10 +0300)]
[SCSI] isd200: use one-element sg list in issuing commands
- This patch should be commited before:
usb: transport - convert to accessors and !use_sg code path removal
- isd200_action() was still using direct liniar pointers in issuing
commands to the USB transport level. This is no longer supported,
use one-element scatterlist instead.
- Adjustment of command's length in the case of scsi-to-ata translation
is now restored before return to queuecommand, since other wise it can
leak BIOs.
- isd200_action() return Error on unknown requests. Used to print an error
but still try to send garbage cdb.
- convert few places to scsi data accessors.
- Todo: This file will need to be changed when scsi_cmnd changes to
scsi_data_buffer or any other solution.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
[SCSI] usb: shuttle_usbat - convert to accessors and !use_sg code path removal
- functions that received char* but where passed scatterlist* mostly
were changed to receive void*
- Use scsi data accessors and remove of !use_sg code path
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Acked-by: Matthew Dharm <mdharm-scsi@one-eyed-alien.net> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Boaz Harrosh [Wed, 17 Oct 2007 08:43:20 +0000 (10:43 +0200)]
[SCSI] seagate: Remove driver
- Apparently no one wonts this driver, and no one
is willing to fix it for future changes to SCSI.
So remove it, and if someone wants it in the future
He can revive it with the needed fixes.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The psi240i driver is still written for cmnd->request_buffer
as a char pointer to actual data. There was never any attempt
to use the scatterlist option.
- remove all source files (3) from drivers/scsi
- Remove from Makefile and Kconfig
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Christie [Thu, 1 Nov 2007 01:59:56 +0000 (20:59 -0500)]
[SCSI] add DID_REQUEUE string to scsi_show_result host table
I was working on patches which add new transport error values, when I
noticed that DID_REQUEUE was not in the hostbyte_table. I do not think
there is any way to hit the code path where scsi_show_result is called
and where you return DID_REQUEUE, because DID_REQUEUE causes scsi-ml to
always requeue the command. However, for completeness and because I want
to one day send a patch that tries to add new host bytes values, I am
sending this patch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Smart [Sat, 27 Oct 2007 17:37:53 +0000 (13:37 -0400)]
[SCSI] lpfc 8.2.3 : Miscellaneous Small Fixes - part 2
Miscellaneous Small Fixes - part 2
- Fix ndlp left in PLOGI state after link up
- Fix cannot rcv unsol ELS frames after running HBA resets for a few minutes
- Fix HBQ buffer_count implemention
- Fix RPI leak
- Fix crash while deleting vports while HBA is reset
- Revert the FCP Fbits offset back to 7
- Fix panic when deleting vports
- Remove unused code in switch statement outside of a case
- Reject PLOGI from invalid PName or NName of 0
- Ignore PLOGI responses from WWPName or WWNName of 0
- Fix debugfs hbqinfo display for ppc
- Added 8G to list of supported speeds for sysfs parameter
- Defer ndlp cleanup to dev-loss timeout handler
- Added support for WRITE_VPARMS mailbox command by applications
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Smart [Sat, 27 Oct 2007 17:37:43 +0000 (13:37 -0400)]
[SCSI] lpfc 8.2.3 : FC Discovery Fixes
FC Discovery Fixes:
- Fix up lpfc_drop_node() vs lpfc_nlp_not_used() usage
- Clear ADISC flag when unregistering RPI and REMOVE ndlps if in recovery.
- Fix usage of UNUSED list and ndlps
- Fix PLOGI race conditions
- Reset link if NameServer PLOGI errors occur
- Synchronize GID_FT queries with PLOGI receptions
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Smart [Sat, 27 Oct 2007 17:37:33 +0000 (13:37 -0400)]
[SCSI] lpfc 8.2.3 : Miscellaneous Small Fixes - part 1
Miscellaneous Small Fixes - part 1
- Fix typo kmzlloc -> kzalloc
- Fix discovery ndlp use after free panic
- Fix link event causing flood of 0108 messages
- Relieve some mbox congestion on link up with 100 vports
- Fix broken vport parameters
- Prevent lock recursion in logo_reglogin_issue
- Split uses of error variable in lpfc_pci_probe_one into retval and error
- Remove completion code related to dev_loss_tmo
- Remove unused LPFC_MAX_HBQ #define
- Don't compare pointers to 0 for sparse
- Make 2 functions static for sparse
- Fix default rpi cleanup code causing rogue ndlps to remain on the NPR list
- Remove annoying ELS messages when driver is unloaded
- Fix Cannot issue Register Fabric login problems on link up
- Remove LPFC_EVT_DEV_LOSS_DELAY
- Fix FC port swap test leads to device going offline
- Fix vport CT flags to only be set when accepted
- Add code to handle signals during vport_create
- Fix too many retries in FC-AL mode
- Pull lpfc_port_link_failure out of lpfc_linkdown_port
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
James Smart [Sat, 27 Oct 2007 17:37:17 +0000 (13:37 -0400)]
[SCSI] lpfc 8.2.3 : NPIV bug fixes
NPIV bug fixes:
- Remove vport params on physical hba when npiv is disabled
- Implement new DA_ID CT command to remove vport information from
the switch after delete. Some switches didn't clean this up unless
the physical link dropped.
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Brian King [Thu, 25 Oct 2007 21:06:34 +0000 (16:06 -0500)]
[SCSI] ibmvscsi: Set default command timeout
Set the default command timeout for ibmvscsi disks to 60 seconds
to ensure we don't prematurely timeout commands. This fixes a problem
seen where the default 30 seconds was not long enough due to
congestion on the server.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Gilbert Wu [Mon, 22 Oct 2007 22:19:11 +0000 (15:19 -0700)]
[SCSI] aic94xx: update BIOS image from user space.
1. Create a file "update_bios" in sysfs to allow user to update bios
from user space.
2. The BIOS image file can be downloaded from web site
"http://www.adaptec.com/en-US/downloads/bios_fw/bios_fw_ver?productId=SAS-48300&dn=Adaptec+Serial+Attached+SCSI+48300"
and copy the BIOS image into /lib/firmware folder.
3. The aic994xx will accept "update bios_file" and "verify bios_file"
commands to perform update and verify BIOS image .
For example:
Type "echo "update asc483c01.ufi" > /sys/devices/.../update_bios"
to update BIOS image from /lib/firmware/as483c01.ufi file into
HBA's flash memory.
Type "echo "verify asc483c01.ufi" > /sys/devices/.../update_bios"
to verify BIOS image between /lib/firmware/asc48c01.ufi file
and
HBA's flash memory.
4. Type "cat /sys/devices/.../update_bios" to view the status or
result
of updating BIOS.
Signed-off-by: Gilbert Wu <gilbert_wu@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Kay Sievers [Tue, 14 Aug 2007 12:10:39 +0000 (14:10 +0200)]
[SCSI] sr,sd: send media state change modification events
This will send for a card reader slot (remove/add media):
UEVENT[1187091572.155884] change /devices/pci0000:00/0000:00:1d.7/usb5/5-2/5-2:1.0/host7/target7:0:0/7:0:0:0 (scsi)
UEVENT[1187091572.162314] remove /block/sdb/sdb1 (block)
UEVENT[1187091572.172464] add /block/sdb/sdb1 (block)
UEVENT[1187091572.175408] change /devices/pci0000:00/0000:00:1d.7/usb5/5-2/5-2:1.0/host7/target7:0:0/7:0:0:0 (scsi)
and for a DVD drive (add/eject media):
UEVENT[1187091590.189159] change /devices/pci0000:00/0000:00:1f.1/host4/target4:0:0/4:0:0:0 (scsi)
UEVENT[1187091590.957124] add /module/isofs (module)
UEVENT[1187091604.468207] change /devices/pci0000:00/0000:00:1f.1/host4/target4:0:0/4:0:0:0 (scsi)
Userspace gets events, even for unpartitioned media. This unifies
the event handling for asynchronoous events (AN) and events caused by
perodical polling the device from userspace.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
[jejb: modified for new event API]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Linus Torvalds [Fri, 11 Jan 2008 19:48:00 +0000 (11:48 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Replace 40c7869b693b18412491fdcff64682215b739f9e kludge
[MIPS] Lasat: Fix built in separate object directory.
[MIPS] Malta: Fix software reset on big endian
[MIPS] pnx8xxx: move to clocksource
[MIPS] Wrong CONFIG option prevents setup of DMA zone.
This change avoids the deadlock by moving the acquire_console_sem()
out of ps3fb_sync(), and puts it into the two other callsites, leaving
ps3fb_release() to call ps3fb_sync() without the console semaphore.
[Geert]
- Corrected call sequence above
- ps3fb_release() may be called with and without console_sem held. This is an
inconsistency that should be fixed at the fb level, but for now, try to
acquire console_sem in ps3fb_release().
I think it's safer to let ps3fb_release() try to acquire console_sem and
not refresh the screen if it fails, than to call ps3fb_sync() without
holding console_sem, as ps3fb_par may be modified at the same time, causing
crashes or lockups.
Besides, ps3fb_release() only calls ps3fb_sync() to refresh the screen
when display flipping is disabled, which is an uncommon case (except during
shutdown/kexec).
Signed-off-by: Jeremy Kerr <jk@ozlabs.org> Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeremy Kerr [Fri, 11 Jan 2008 13:27:10 +0000 (14:27 +0100)]
ps3fb: prevent use after free of fb_info
In ps3fb_shutdown, freeing the framebuffer will cause fb_info (in
dev->core.driver_data) to be free()ed, which we potentially access
from the ps3fbd kthread.
This change frees the framebuffer after stopping the ps3fbd kthread.
Linus Torvalds [Fri, 11 Jan 2008 19:44:59 +0000 (11:44 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
blktrace: kill the unneeded initcall
block: fix blktrace timestamps
loop: fix bad bio_alloc() nr_iovec request
Don't blatt first element of prv in sg_chain()
Massimo Cirillo [Fri, 11 Jan 2008 10:24:11 +0000 (10:24 +0000)]
cache invalidation error for buffered write
The bug causes corruptions of data read from flash.
The original code performs cache invalidation from "adr" to "adr + len"
in do_write_buffer(). Since len and adr could be updated in the code
before invalidation - it causes improper setting of cache invalidation
regions.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com> Signed-off-by: Giuseppe D'Eliseo <giuseppedeliseo@gmail.com> Acked-by: Nicolas Pitre <nico@cam.org> Acked-by: Jörn Engel <joern@logfs.org> Signed-off-by: David Woohouse <dwmw2@infradead.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dmitri Vorobiev [Tue, 8 Jan 2008 03:44:00 +0000 (06:44 +0300)]
[MIPS] Malta: Fix software reset on big endian
I noticed that the commit f197465384bf7ef1af184c2ed1a4e268911a91e3
(MIPS Tech: Get rid of volatile in core code) broke the software
reset functionality for MIPS Malta boards in big-endian mode.
According to the MIPS Malta board user's manual, writing the magic
32-bit GORESET value into the SOFTRES register initiates board soft
reset. My experimentation has shown that the endianness of the GORESET
integer should thereby be the same as the endianness, which has been
set for the CPU itself. The writew() function used to write the magic
value in the code introduced by the commit mentioned above, however,
swaps bytes for big-endian kernels and transfers 16 bits instead of 32.
The patch below replaces the writew() function by the __raw_writel()
routine, which leaves the byte order intact and transfers the whole
MIPS machine word. Trivial code cleanup (replacing spaces by a tab
and cutting oversized lines to make checkpatch.pl happy) is also
included.
The patch was tested using a Malta evaluation board running in both
BE and LE modes. For both modes, software reset was fully functional
after the change.
P.S. I suspect that the same commit broke the "standby" functionality
for MIPS Atlas boards. However, I did not touch the Atlas code as I
don't have such board at my disposal and also because the linux-mips.org
Web site claims that Atlas support is scheduled for removal.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com> Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hans Verkuil [Thu, 10 Jan 2008 21:33:16 +0000 (18:33 -0300)]
V4L/DVB (6999): ivtv: stick to udelay=10 after all
Using an udelay of 5 seems to result in problems for several people.
For now abandon the udelay value of 5 and stick to 10, even though this
will mean a longer load time of the cx2584x firmware.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ingo Molnar [Fri, 11 Jan 2008 12:35:54 +0000 (13:35 +0100)]
block: fix blktrace timestamps
David Dillow reported broken blktrace timestamps. The reason
is cpu_clock() which is not a global time source.
Fix bkltrace timestamps by using ktime_get() like the networking
code does for packet timestamps. This also removes a whole lot
of complexity from bkltrace.c and shrinks the code by 500 bytes:
text data bss dec hex filename
2888 124 44 3056 bf0 blktrace.o.before
2390 116 44 2550 9f6 blktrace.o.after
This patch should fix the issue seen on Alpha with unaligned accesses in
the new readdir code. By aligning each dirent to sizeof(u64) we'll avoid
unaligned accesses. To make doubly sure we're not hitting problems also
rearrange struct hack_dirent to avoid holes.
Paul Mundt [Fri, 11 Jan 2008 04:18:16 +0000 (13:18 +0900)]
sh: Force __access_ok() to obey address space limit.
When the thread_info->addr_limit changes were introduced, __access_ok()
was missed in the conversion, allowing user processes to perform P1/P2
accesses under certain conditions.
This has already been corrected with the nommu refactoring in later
kernels.
Linus Torvalds [Thu, 10 Jan 2008 22:53:37 +0000 (14:53 -0800)]
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata and starting/stopping ATAPI floppy devices
sata_sil24: prevent hba lockup when pass-through ATA commands are used
Update kernel parameter document for libata DMA mode setting knobs.
libata: don't normalize UNKNOWN to NONE after reset
libata-pmp: propagate timeout to host link
libata-pmp: 4726 hates SRST
pata_ixp4xx_cf: fix compilation introduced by ata_port_desc() conversion
pata_pdc202xx_old: Further fixups
libata-sff: PCI IRQ handling fix
sata_qstor: use hardreset instead of softreset
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
trm290: do hook dma_host_{on,off} methods (take 2)
ide: fix cable detection for SATA bridges
ide: workaround suspend bug for ACPI IDE
Shaohua Li [Thu, 10 Jan 2008 22:03:42 +0000 (23:03 +0100)]
ide: workaround suspend bug for ACPI IDE
http://bugzilla.kernel.org/show_bug.cgi?id=9673
ACPI _PS3 cause S4 breaks in the second attempt. The system has a _PS3
method for IDE, which will call into SMM mode. Currently we haven't clue
why just the second attempt fails, as it's totally in BIOS code, so
blacklist the system so far for 2.6.24.
A possible suspect is ACPI NVS isn't save/restore, we will revisit the
bug after linux does ACPI NVS save/restore.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Reported-by: Mikko Vinni <mmvinni@yahoo.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Gwendal Grignou [Thu, 10 Jan 2008 06:47:56 +0000 (15:47 +0900)]
sata_sil24: prevent hba lockup when pass-through ATA commands are used
Fix commands timeout with Sil3124/3132 based HBA when pass-through ATA
commands [where ATA_QCFLAG_RESULT_TF is set] are used while other
commands are active on other devices connected to the same port with a
Port Multiplier. Due to a hardware bug, these commands must be sent
alone, like ATAPI commands.
Tejun Heo [Tue, 8 Jan 2008 11:26:12 +0000 (20:26 +0900)]
libata: don't normalize UNKNOWN to NONE after reset
After non-classifying reset, ehc->classes[] could contain
ATA_DEV_UNKNOWN which used to be normalized to ATA_DEV_NONE for
consistency. However, this causes unfortunate side effect for drivers
which have non-classifying hardresets (e.g. sata_nv) by making
hardreset report ATA_DEV_NONE for non-classifying resets and thus
makes EH believe that the port is unoccupied and recovery can be
skipped. The end result is that after a device is swapped with
another one, the new device isn't attached after the old one is
detached.
This patch makes ata_eh_reset() not normalize UNKNOWN to NONE after
non-classifying resets. This fixes the above problem. As UNKNOWN and
NONE are handled differently by only EH hotplug logic, this doesn't
cause other behavior changes.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Robert Hancock <hancockr@shaw.ca> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Fri, 4 Jan 2008 00:08:49 +0000 (00:08 +0000)]
pata_pdc202xx_old: Further fixups
Turns out distros always enabled burst mode and it is pretty essential so
do the same. Also sort out the post DMA mode restore properly.
My 20263 card now seems happy but needs some four drive tests done yet
(when I've persuaded the kernel not to hang in the edd boot code if I
plug them in ..)
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Thu, 3 Jan 2008 17:22:28 +0000 (17:22 +0000)]
libata-sff: PCI IRQ handling fix
It is legitimate (although annoying and silly) for a PCI IDE controller
not to be assigned an interrupt and to be polled. The libata-sff code
should therefore not try and request IRQ 0 in this case.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Thu, 3 Jan 2008 15:22:19 +0000 (00:22 +0900)]
sata_qstor: use hardreset instead of softreset
During conversion to new EH, sata_qstor was accidentaly changed to use
softreset, which is buggy on this chip, instead of hardreset. This
patch updates sata_qstor such that it uses hardreset again.
This fixes bugzilla bug 9631.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Mark Lord <mlord@pobox.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Herbert Xu [Thu, 10 Jan 2008 21:09:35 +0000 (08:09 +1100)]
[CRYPTO] padlock: Fix alignment fault in aes_crypt_copy
The previous patch fixed spurious read faults from occuring by copying
the data if we happen to have a single block at the end of a page. It
appears that gcc cannot guarantee 16-byte alignment in the kernel with
__attribute__. The following report from Torben Viets shows a buffer
that's only 8-byte aligned:
FUJITA Tomonori [Tue, 8 Jan 2008 14:07:01 +0000 (23:07 +0900)]
[SCSI] qla1280: fix 32 bit segment code
There's an error remaining in the 32 bit descriptor code after the
conversion to dma accessors: req_cnt is left uninitialised.
qla1280_32bit_start_scsi gives the following warnings:
drivers/scsi/qla1280.c: In function 'qla1280_32bit_start_scsi':
drivers/scsi/qla1280.c:3044: warning: unused variable 'dma_handle'
drivers/scsi/qla1280.c: In function 'qla1280_queuecommand':
drivers/scsi/qla1280.c:3060: warning: 'req_cnt' is used uninitialized in this function
drivers/scsi/qla1280.c:3042: note: 'req_cnt' was declared here
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
projects / linux-2.6 / log