David S. Miller [Tue, 28 Jun 2005 22:25:31 +0000 (15:25 -0700)]
[NET]: Remove gratuitous use of skb->tail in network drivers.
Many drivers use skb->tail unnecessarily.
In these situations, the code roughly looks like:
dev = dev_alloc_skb(...);
[optional] skb_reserve(skb, ...);
... skb->tail ...
But even if the skb_reserve() happens, skb->data equals
skb->tail. So it doesn't make any sense to use anything
other than skb->data in these cases.
Another case was the s2io.c driver directly mucking with
the skb->data and skb->tail pointers. It really just wanted
to do an skb_reserve(), so that's what the code was changed
to do instead.
Another reason I'm making this change as it allows some SKB
cleanups I have planned simpler to merge. In those cleanups,
skb->head, skb->tail, and skb->end pointers are removed, and
replaced with skb->head_room and skb->tail_room integers.
Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Jeff Garzik <jgarzik@pobox.com>
Vlad Yasevich [Tue, 28 Jun 2005 20:24:23 +0000 (13:24 -0700)]
[SCTP] Make init & delayed sack timeouts configurable by user.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Maxime Bizon [Tue, 28 Jun 2005 20:21:12 +0000 (13:21 -0700)]
[IPV4]: ipconfig.c: fix dhcp timeout behaviour
I think there is a small bug in ipconfig.c in case IPCONFIG_DHCP is set
and dhcp is used.
When a DHCPOFFER is received, ip address is kept until we get DHCPACK.
If no ack is received, ic_dynamic() returns negatively, but leaves the
offered ip address in ic_myaddr.
This makes the main loop in ip_auto_config() break and uses the maybe
incomplete configuration.
Not sure if it's the best way to do, but the following trivial patch
correct this.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
Dietmar Eggemann [Tue, 28 Jun 2005 20:06:23 +0000 (13:06 -0700)]
[IPV4]: Snmpv2 Mib IP counter ipInAddrErrors support
I followed Thomas' proposal to see every martian destination as a case
where the ipInAddrErrors counter has to be incremented. There are
two advantages by doing so: (1) The relation between the ipInReceive
counter and all the other ipInXXX counters is more accurate in the
case the RTN_UNICAST code check fails and (2) it makes the code in
ip_route_input_slow easier.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@gmx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 28 Jun 2005 19:39:40 +0000 (12:39 -0700)]
[EBTABLES]: Fix thinkos in ebt_log.c
When converting over the skb_header_pointer(), I converted parts of
this module incorrectly. Kill the 'u' union in ebt_log() and all the
bogus references to it.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tejun Heo [Sun, 26 Jun 2005 14:27:19 +0000 (23:27 +0900)]
[PATCH] libata: lengthen COMMRESET delay
This patch lengthens the delay between DET setting and clearing for
COMMRESET from 400us to 1ms. I couldn't find any requiremen regarding
the duration of COMMRESET in SATA I/II specs but AHCI-1.1 10.4.2
states that it should be at least 1ms.
Andrew Morton [Tue, 28 Jun 2005 03:14:05 +0000 (20:14 -0700)]
[PATCH] cfq build fix
drivers/block/cfq-iosched.c: In function 'cfq_put_queue':
drivers/block/cfq-iosched.c:303: sorry, unimplemented: inlining failed in call to 'cfq_pending_requests': function body not available
drivers/block/cfq-iosched.c:1080: sorry, unimplemented: called from here
drivers/block/cfq-iosched.c: In function '__cfq_may_queue':
drivers/block/cfq-iosched.c:1955: warning: the address of 'cfq_cfqq_must_alloc_slice', will always evaluate as 'true'
make[1]: *** [drivers/block/cfq-iosched.o] Error 1
make: *** [drivers/block/cfq-iosched.o] Error 2
Cc: Jeff Garzik <jgarzik@pobox.com> Cc: Jens Axboe <axboe@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Tobias Klauser [Mon, 16 May 2005 17:15:11 +0000 (19:15 +0200)]
[PATCH] Use pci_set_dma_mask() instead of direct assignment of DMA mask
The amd8111e driver directly assigns the DMA mask to the dma_mask
member of the struct pci_dev instead of using pci_set_dma_mask(). This
makes the call to pci_dma_supported() redundant as pci_set_dma_mask()
does this check.
I do not own this device so I only compile-tested this patch.
David Brownell [Mon, 16 May 2005 15:53:52 +0000 (08:53 -0700)]
[PATCH] smc91x needs settable IRQ trigger type
For boards that invert the SMC91x IRQ line (maybe an FPGA inverts it),
the set_irq_type() call can't assume IRQT_RISING. These particular
boards currently use OMAP-specific calls to change the trigger type,
but the boards break when set_irq_type() stops being a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
[PATCH] ACPI-based PCI resources: PCMCIA bugfix, but resources missing in trees
Don't auto-configure yenta sockets for PCMCIA devices if it is connected to
the root PCI bus on the x86 or x86_64 architectures. Previously, this was
handled by the "ioport_resource"/"iomem_resource" check a few lines below,
but with the new ACPI-based resource handling this doesn't catch all cases
any longer.
pci-yenta-cardbus-fix.patch and this patch should solve the initialization
time trouble. However, the ACPI-based PCI resource handling is badly
broken, IMHO:
- many resources of devices don't show up in the resource trees (
/proc/iomem and /proc/ioports) any longer. This means that PCMCIA, but
also possibly other subsystems (ISA, PnP, ...) do not know which resources
it cannot use.
- verify_root_windows() should fail if there are no iomem _or_ ioport
resources, not only if there are no iomem _and_ ioport resources.
[PATCH] pcmcia: 8 and 16 bit access for static_map
The PCMCIA card services layer is never setting the i/o map attributes when
SS_CAP_STATIC_MAP is specified. Net result, sockets' set_io_map() calls
always see requests with most flags clear, meaning 8 bit access.
For hardware that always autosizes, that won't matter; and all current
STATIC_MAP drivers ignore those attributes. A new driver (for at91rm9200)
suffers badly from this, since this forces everything into 8 bit mode and
that breaks both (a) cards requiring 16 bit access, and (b) ide-cs; but of
course 8-bit cards work OK (as does accessing card attributes).
So this patch arranges to pass the attributes down, matching the behavior
for non-static mappings (using the first/only I/O window).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- properly bail out in set_cis_map if call to socket driver's set_mem_map
failed
- don't abort do_mem_probe cycle if one entry failed (!CONFIG_PCMCIA_PROBE)
- don't do iomem probing in chunks larger than 0x800000 (1 << 23) as
yenta_socket and vrc4173_cardu.c fail to set_mem_map for windows equal to
or larger than (1 << 24).
[PATCH] pcmcia: synclink_cs IRQ_INFO2_INFO is gone
Remove the IRQ_INFO2_VALID flag in synclink_cs -- I overlooked it when
removing all other users in PCMCIA drivers for 2.6.11. Thanks to Marcelo
Tosatti for noticing it.
[PATCH] pcmcia: move PCMCIA ioctl to a separate file
Move all PCMCIA_IOCTL-related code to a different file.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
From: Richard Purdie <rpurdie@rpsys.net>
The pcmcia-move-pcmcia-ioctl-to-a-separate-file patch was corrupted in -mm2
causing this problem. Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some information useful for PCMCIA device driver authors to
Documentation/pcmcia/, and reference it in dmesg in case of hash mismatches.
Also add a reference to pcmciautils to Documentation/Changes. With recent
changes, you don't need to concern yourself with pcmcia-cs even if you have
PCMCIA hardware, so the example above the list needed to be adapted as well.
Add pcmcia_device_id table to pcmciamtd. The binding of anonymus cards (i.e.
those who do neither report MANFID, CARDID, FUNCID nor product strings) is
protected by a new config option.
This patch contains the following cleanups:
- make needlessly global code static
- remove the following unneeded EXPORT_SYMBOL's:
- ds.c: pcmcia_report_error
- ds.c: pcmcia_bus_type
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] pcmcia: request CIS via firmware interface
Use the firmware method to load replacement CIS tables. It is recommended
that the /lib/firmware/cis/ points to /etc/pcmcia/cis or the other way round
so that both old-style cardmgr and new-style hotplug/firmware can access these
"overwrite" files
The "func_id"-based matching is very fuzzy and can lead to false positives.
Therefore, it should be tried to avoid relying on these matches. Until
most/all existing func_id-based matches are replaced by
manf_id/card_id/prod_id matches (a patch which will ask to send the
appropriate card information to the PCMCIA mailing list will be added once
other, more pressing issues are adressed), we need to emulate cardmgr
behaviour by allowing func_id matches if no manf_id/card_id/prod_id match
occurs. This can only be done in userspace because of modules possibly loaded
with long delays. So, add a per-device sysfs file for this purpose.
If a card doesn't provide _any_ information about itself, assume it is a
so-called "anonymous" card. pcmciamtd will bind to it if it is configured to
do so.
The one thing which surprises me in this patch that cis->Length needs to be
set to count+1. Without it, it doesn't work, but with it, it doesn't make
sense to me.
projects / linux-2.6 / log