[PATCH] ahci: Ensure that we don't grab both functions
When we force the chip into dual fn mode so we get PATA and AHCI we must
be sure we don't then do anything dumb like try and grab both with the AHCI
driver.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement controller-wide PM. ata_host_set_suspend/resume() are
defined to suspend and resume a host_set. While suspended, EHs for
all ports in the host_set are pegged using ATA_FLAG_SUSPENDED and
frozen.
Because SCSI device hotplug is done asynchronously against the rest of
libata EH and the same mutex is used when adding new device, suspend
cannot wait for hotplug to complete. So, if SCSI device hotplug is in
progress, suspend fails with -EBUSY.
In most cases, host_set resume is followed by device resume. As each
resume operation requires a reset, a single host_set-wide resume
operation may result in multiple resets. To avoid this, resume waits
upto 1 second giving PM to request resume for devices.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement per-dev PM. The original implementation directly put the
device into suspended mode and didn't synchronize w/ EH operations
including hotplug. This patch reimplements ata_scsi_device_suspend()
and ata_scsi_device_resume() such that they request EH to perform the
respective operations. Both functions synchronize with hotplug such
that it doesn't operate on detached devices.
Suspend waits for completion but resume just issues request and
returns. This allows parallel wake up of devices and thus speeds up
system resume.
Due to sdev detach synchronization, it's not feasible to separate out
EH requesting from sdev handling; thus, ata_device_suspend/resume()
are removed and everything is implemented in the respective
libata-scsi functions.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement two PM per-dev EH actions - ATA_EH_SUSPEND and
ATA_EH_RESUME. Each action puts the target device into suspended mode
and resumes from it respectively.
Once a device is put to suspended mode, no EH operations other than
RESUME is allowed on the device. The device will stay suspended till
it gets resumed and thus reset and revalidated. To implement this, a
new device state helper - ata_dev_ready() - is implemented and used in
EH action implementations to make them operate only on attached &
running devices.
If all possible devices on a port are suspended, reset is skipped too.
This prevents spurious events including hotplug events from disrupting
suspended devices.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH] libata: separate out __ata_ehi_hotplugged()
Separate out __ata_ehi_hotplugged() from ata_ehi_hotplugged(). The
underscored version doesn't set AC_ERR_ATA_BUS. This will be used for
resume which is a hotplug event but not an ATA bus error.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH] libata: implement ATA_EHI_NO_AUTOPSY and QUIET
Implement ATA_EHI_NO_AUTOPSY and QUIET. These used to be implied by
ATA_PFLAG_LOADING, but new power management and PMP support need to
use these separately. e.g. Suspend/resume operations shouldn't print
full EH messages and resume shouldn't be recorded as an error.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH] libata: clean up debounce parameters and improve parameter selection
The names of predefined debounce timing parameters didn't exactly
match their usages. Rename to more generic names and implement param
selection helper sata_ehc_deb_timing() which uses EHI_HOTPLUGGED to
select params.
Combined with the previous EHI_RESUME_LINK differentiation, this makes
parameter selection accurate. e.g. user scan resumes link but normal
deb param is used instead of hotplug param.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_EHI_RESUME_LINK, which indicates that the link needs to
be resumed. This used to be implied by ATA_EHI_HOTPLUGGED. However,
hotplug isn't the only event which requires link resume and separating
this out allows other places to request link resume. This
differentiation also allows better debounce timing selection.
This patch converts user scan to use ATA_EHI_RESUME_LINK.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH] libata: replace ap_lock w/ ap->lock in ata_scsi_error()
ap_lock was used because &ap->host_set->lock was too long and used a
lot. Now that &ap->host_set->lock is replaced with ap->lock, there's
no reason to keep ap_lock.
[ed. note: that's not entirely true. ap_lock is a local variable,
caching the results of a de-ref. In theory, if the compiler is smart
enough, this patch is cosmetic. However, since this is not a fast
path (it is the error path), this patch is nonetheless acceptable,
even though it _may_ introduce a performance regression.]
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH] libata: fix ehc->i.action setting in ata_eh_autopsy()
ata_eh_autopsy() used to directly assign determined action mask to
ehc->i.action thus overriding actions set by some of nested analyze
functions. This patch makes ata_eh_autopsy() add action masks just as
it's done in other places.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Wed, 28 Jun 2006 16:29:30 +0000 (01:29 +0900)]
[PATCH] libata: add ap->pflags and move core dynamic flags to it
ap->flags is way too clamped. Separate out core dynamic flags to
ap->pflags. ATA_FLAG_DISABLED is a dynamic flag but left alone as
it's referenced by a lot of LLDs and it's gonna be removed once all
LLDs are converted to new EH.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.linux-nfs.org/pub/linux/nfs-2.6:
NLM,NFSv4: Wait on local locks before we put RPC calls on the wire
VFS: Add support for the FL_ACCESS flag to flock_lock_file()
NFSv4: Ensure nfs4_lock_expired() caches delegated locks
NLM,NFSv4: Don't put UNLOCK requests on the wire unless we hold a lock
VFS: Allow caller to determine if BSD or posix locks were actually freed
NFS: Optimise away an excessive GETATTR call when a file is symlinked
This fixes a panic doing the first READDIR or READDIRPLUS call when:
NFS: Fix NFS page_state usage
Revert "Merge branch 'odirect'"
Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (39 commits)
[PATCH] myri10ge - Export more parameters to ethtool
[PATCH] myri10ge - Use dev_info() when printing parameters after probe
[PATCH] myri10ge - Drop ununsed nvidia chipset id
[PATCH] myri10ge - Drop unused pm_state
[PATCH] Fix freeing of net device
[PATCH] remove dead entry in net wan Kconfig
[PATCH] NI5010 netcard cleanup
[PATCH] lock validator: fix ns83820.c irq-flags bug
[PATCH] pcnet32: Cleanup rx buffers after loopback test.
[PATCH] pcnet32: Suspend the chip rather than restart when changing multicast/promisc
[PATCH] pcnet32: Handle memory allocation failures cleanly when resizing tx/rx rings
[PATCH] pcnet32: Use kcalloc instead of kmalloc and memset
[PATCH] pcnet32: Fix off-by-one in get_ringparam
[PATCH] pcnet32: Use PCI_DEVICE macro
[PATCH] pcnet32: Fix Section mismatch error
[PATCH] Add support for the Cicada 8201 PHY
[PATCH] zd1211rw: disable TX queue during stop
[PATCH] ZyDAS ZD1211 USB-WLAN driver
[PATCH] softmac: fix build-break from 881ee6999d66c8fc903b429b73bbe6045b38c549
[PATCH] CONFIG_WIRELESS_EXT is neccessary after all
...
[PATCH] myri10ge - Use dev_info() when printing parameters after probe
Displaying the interface name when listing the device parameters
at the end of myri10ge_probe is not a good idea since udev might
rename the interface soon afterwards.
Print the bus id instead, using dev_info().
Signed-off-by: Brice Goglin <brice@myri.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Paul Fulghum [Fri, 30 Jun 2006 09:27:19 +0000 (02:27 -0700)]
[PATCH] remove dead entry in net wan Kconfig
Remove dead entry from net wan Kconfig and net wan Makefile.. This entry is
left over from 2.4 where synclink used syncppp driver directly. synclink
drivers now use generic HDLC
Signed-off-by: Paul Fulghum <paulkf@microgate.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Andreas Mohr [Fri, 30 Jun 2006 09:25:07 +0000 (02:25 -0700)]
[PATCH] NI5010 netcard cleanup
- updated MAINTAINERS entry to new format
- updated Jan-Pascal's (ACKed) and my email address
- driver cleanup/modernization (runtime-, not hardware-tested)
[bunk@stusta.de: build fix] Signed-off-by: Andreas Mohr <andi@lisas.de> Cc: Jeff Garzik <jeff@garzik.org> Cc: Jan-Pascal van Best <jvbest@qv3pluto.leidenuniv.nl> Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
this is caused because the ns83820 driver re-enables irq flags
in hardirq context.
While legal in theory, in practice it should only be done if the
hardware is really old and has some very high overhead in its ISR.
(such as PIO IDE)
For modern hardware, running ISRs with irqs enabled is discouraged,
because 1) new hardware is fast enough to not cause latency problems
2) allowing the nesting of hardware interrupts only 'spreads out'
the handling of the current ISR, causing extra cachemisses that would
otherwise not happen. Furthermore, on architectures where ISRs share
the kernel stacks, enabling interrupts in ISRs introduces a much
higher kernel-stack-nesting and thus kernel-stack-overflow risk.
3) not managing irq-flags via the _irqsave / _irqrestore variants
is dangerous: it's easy to forget whether one function nests inside
another, and irq flags might be mismanaged.
In the few cases where re-enabling interrupts in an ISR is considered
useful (and unavoidable), it has to be taught to the lock validator
explicitly (because the lock validator needs the "no ISR ever enables
hardirqs" artificial simplification to keep the IRQ/softirq locking
dependencies manageable).
This teaching is done via the explicit use local_irq_enable_in_hardirq().
On a stock kernel this maps to local_irq_enable(). If the lock validator
is enabled then this does not enable interrupts.
Now, the analysis of drivers/net/ns83820.c's irq flags use: the
irq-enabling in irq context seems intentional, but i dont think it's
justified. Furthermore, the driver suffers from problem #3 above too,
in ns83820_tx_timeout() it disables irqs via local_irq_save(), but
then it calls do_tx_done() which does a spin_unlock_irq(),
re-enabling for a function that does not expect it! While currently
this bug seems harmless (only some debug printout seems to be
affected by it), it's nevertheless something to be fixed.
So this patch makes the ns83820 ISR irq-flags-safe, and cleans up
do_tx_done() use and locking to avoid the ns83820_tx_timeout() bug.
From: Arjan van de Ven <arjan@linux.intel.com>
ns83820_mib_isr takes the misc_lock in IRQ context. All other places that
do this in the ISR already use _irqsave versions, make this consistent at
least. At some point in the future someone should audit the driver to see
if all _irqsave's in the ISR can go away, this is generally an iffy/fragile
proposition though; for now get it safe, simple and consistent.
From: Arjan van de Ven <arjan@linux.intel.com>
ok this is a real driver deadlock:
The ns83820 driver enabled interrupts (by unlocking the misc_lock with
_irq) while still holding the rx_info.lock, which is required to be irq
safe since it's used in the ISR like this:
writel(1, dev->base + IER);
spin_unlock_irq(&dev->misc_lock);
kick_rx(ndev);
spin_unlock_irq(&dev->rx_info.lock);
This is can cause a deadlock if an irq was pending at the first
spin_unlock_irq already, or if one would hit during kick_rx().
Simply remove the first _irq solves this
Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Benjamin LaHaise <bcrl@kvack.org> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don Fry [Thu, 29 Jun 2006 20:55:02 +0000 (13:55 -0700)]
[PATCH] pcnet32: Suspend the chip rather than restart when changing multicast/promisc
Suspend the chip if possible rather than stop and discard all tx and rx
frames, when changing the mcast list or entering/leaving promiscuous
mode. Created common pcnet32_suspend routine.
Tested ia32 and ppc64
Signed-off-by: Don Fry <brazilnut@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix pcnet32_set_ringparam to handle memory allocation errors without
leaving the adapter in an inoperative state and null pointers waiting to
be dereferenced.
Tested ia32 and ppc64.
Signed-off-by: Don Fry <brazilnut@us.ibm.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kim Phillips [Thu, 29 Jun 2006 02:13:23 +0000 (21:13 -0500)]
[PATCH] Add support for the Cicada 8201 PHY
Add support for the Cicada 8201 PHY, a.k.a Vitesse VSC8201. This PHY is present on the MPC8349mITX.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Daniel Drake [Fri, 2 Jun 2006 16:11:32 +0000 (17:11 +0100)]
[PATCH] ZyDAS ZD1211 USB-WLAN driver
There are 60+ USB wifi adapters available on the market based on the ZyDAS
ZD1211 chip.
Unlike the predecessor (ZD1201), ZD1211 does not have a hardware MAC, so most
data operations are coordinated by the device driver. The ZD1211 chip sits
alongside an RF transceiver which is also controlled by the driver. Our driver
currently supports 2 RF types, we know of one other available in a few marketed
products which we will be supporting soon.
Our driver also supports the newer revision of ZD1211, called ZD1211B. The
initialization and RF operations are slightly different for the new revision,
but the main difference is 802.11e support. Our driver does not support the
QoS features yet, but we think we know how to use them.
This driver is based on ZyDAS's own GPL driver available from www.zydas.com.tw.
ZyDAS engineers have been responsive and supportive of our efforts, so thumbs
up to them. Additionally, the firmware is redistributable and they have
provided device specs.
This driver has been written primarily by Ulrich Kunitz and myself. Graham
Gower, Greg KH, Remco and Bryan Rittmeyer have also contributed. The
developers of ieee80211 and softmac have made our lives so much easier- thanks!
We maintain a small info-page: http://zd1211.ath.cx/wiki/DriverRewrite
If there is enough time for review, we would like to aim for inclusion in
2.6.18. The driver works nicely as a STA, and can connect to both open and
encrypted networks (we are using software-based encryption for now). We will
work towards supporting more advanced features in the future (ad-hoc, master
mode, 802.11a, ...).
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a quick look it seems that wireless_spy_update() lives in
net/core/wirless.c, and that file is only compiled if
CONFIG_WIRELESS_EXT is set. Perhaps this is Kconig work, but
in the mean time here is a reversal of the recent change.
Signed-Off-By: Horms <horms@verge.net.au> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joseph Jezak [Sun, 11 Jun 2006 16:01:03 +0000 (12:01 -0400)]
[PATCH] SoftMAC: Add network to ieee80211softmac_call_events when associate times out
The ieee80211softmac_call_events function, when called with event type
IEEE80211SOFTMAC_EVENT_ASSOCIATE_TIMEOUT should pass the network as the
third parameter. This patch does that.
Signed-off-by: Joseph Jezak <josejx@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joseph Jezak [Sun, 11 Jun 2006 16:00:37 +0000 (12:00 -0400)]
[PATCH] SoftMAC: Prevent multiple authentication attempts on the same network
This patch addresses the "No queue exists" messages commonly seen during
authentication and associating. These appear due to scheduling multiple
authentication attempts on the same network. To prevent this, I added a
flag to stop multiple authentication attempts by the association layer.
I also added a check to the wx handler to see if we're connecting to a
different network than the one already in progress. This scenario was
causing multiple requests on the same network because the network BSSID
was not being updated despite the fact that the ESSID changed.
Signed-off-by: Joseph Jezak <josejx@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Daniel Drake [Fri, 16 Jun 2006 19:50:22 +0000 (20:50 +0100)]
[PATCH] bcm43xx: enable shared key authentication
I recently patched softmac to enable shared key authentication. This small patch
will enable crazy or unfortunate bcm43xx users to use this new capability.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Tue, 20 Jun 2006 14:19:18 +0000 (09:19 -0500)]
[PATCH] 2.6.17 missing a call to ieee80211softmac_capabilities from ieee80211softmac_assoc_req
In commit ba9b28d19a3251bb1dfe6a6f8cc89b96fb85f683, routine
ieee80211softmac_capabilities was added to ieee80211softmac_io.c. As
denoted by its name, it completes the capabilities IE that is
needed in the associate and reassociate requests sent to the
AP. For at least one AP, the Linksys WRT54G V5, the capabilities
field must set the 'short preamble' bit or the AP refuses to
associate. In the commit noted above, there is a call to the
new routine from ieee80211softmac_reassoc_req, but not from
ieee80211softmac_assoc_req. This patch fixes that oversight.
As noted in the subject, v2.6.17 is affected. My bcm43xx card had been
unable to associate since I was forced to buy a new AP. I finally was
able to get a packet dump and traced the problem to the capabilities
info. Although I had heard that a patch was "floating around", I had
not seen it before 2.6.17 was released. As this bug does not affect
security and I seem to have the only AP affected by it, there should
be no problem in leaving it for 2.6.18.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Mon, 26 Jun 2006 02:32:21 +0000 (21:32 -0500)]
[PATCH] Convert bcm43xx-softmac to use the ieee80211_is_valid_channel routine
The current version of bcm43xx-softmac uses local routines to check
if a channel is valid. As noted in the comments, these routines do
not take any regulatory information into account. This patch converts
the code to use the equivalent routine in ieee80211, which is being
converted to know about regulatory information.
Signed-Off-By: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hong Liu [Wed, 21 Jun 2006 03:35:08 +0000 (11:35 +0800)]
[PATCH] ieee80211: fix not allocating IV+ICV space when usingencryption in ieee80211_tx_frame
We should preallocate IV+ICV space when encrypting the frame.
Currently no problem shows up just because dev_alloc_skb aligns the
data len to SMP_CACHE_BYTES which can be used for ICV.
Signed-off-by: Hong Liu <hong.liu@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sat, 17 Jun 2006 13:19:05 +0000 (15:19 +0200)]
[PATCH] bcm43xx: workaround init_board vs. IRQ race
Place the Init-vs-IRQ workaround before any card register
access, because we might not have the wireless core mapped
at all times in init. So this will result in a Machine Check
caused by a bus error.
Signed-off-by: Michael Buesch <mb@bu3sch.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Faidon Liambotis [Sat, 10 Jun 2006 17:54:58 +0000 (20:54 +0300)]
[PATCH] Add two PLX device IDs
This patch adds device IDs for Symbol LA-4123 and Global Sun Tech
GL24110P to the HostAP PLX driver.
This is not tested with real hardware, but there is no reason why it
shouldn't work.
Please test.
Signed-off-by: Faidon Liambotis <faidon@cube.gr> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jeff Garzik [Tue, 27 Jun 2006 13:20:08 +0000 (09:20 -0400)]
[netdrvr] via-velocity: misc. cleanups
- const-ify pci_device_id table
- clean up pci_device_id table with PCI_DEVICE()
- don't store internal pointer in pci_device_id table,
use pci_device_id::driver_data as an integer index
- use dev_printk() for messages where eth%d prefix is unavailable
- formatting fixes
Jeff Garzik [Tue, 27 Jun 2006 12:54:34 +0000 (08:54 -0400)]
[netdrvr] Remove Becker-template 'io_size' member, when invariant
Becker-derived drivers often have the 'io_size' member in their chip
info struct, indicating the minimum required size of the I/O resource
(usually a PCI BAR). For many situations, this number is either
constant or irrelevant (due to pci_iomap convenience behavior).
This change removes the io_size invariant member, and replaces it with a
compile-time constant.
Jeff Garzik [Tue, 27 Jun 2006 11:57:22 +0000 (07:57 -0400)]
[netdrvr] Remove Linux-specific changelogs from several Becker template drivers
When in-kernel net drivers branched from Donald Becker's vanilla driver
set, in the days before BitKeeper and git, a driver changelog was
maintained in the driver source code. These days, the kernel's
changelog is far superior and much more accurate, so the in-driver
changelogs are removed.
Another relic of the Becker/kernel split was version numbering, using
"foo-LKx.y.z" notation, resulting in weird version numbers like
"1.17b-LK1.1.9". These drivers are for older hardware, and see few
changes these days, so the version numbers were all bumped to something
more simple.
Finally, in xircom_tulip_cb specifically, an additional cleanup removes
the always-enabled CARDBUS cpp macro.
Jeff Garzik [Tue, 27 Jun 2006 11:38:33 +0000 (07:38 -0400)]
[netdrvr] epic100: minor cleanups
- Remove in-source changelog, it's in the global kernel history.
- convert silly and useless version to useful one
- replace invariant pci_id_tbl[]::io_size uses with EPIC_TOTAL_SIZE
- remove now-unused io_size member from pci_id_tbl[]
- current kernel style prefers dev_printk() for the rare ethernet driver
messages that cannot print an 'eth%d' prefix.
NFS: Optimise away an excessive GETATTR call when a file is symlinked
In the case when compiling via a symlink tree, we want to ensure that the
close-to-open GETATTR call is applied only to the final file, and not to
the symlink.
The introduction of the FLUSH_INVALIDATE argument to nfs_sync_inode_wait()
does not clear the nr_unstable page state counter for pages that are being
released.
Also fix a longstanding similar bug when nfs_commit_list() fails.
Trond Myklebust [Thu, 29 Jun 2006 20:38:34 +0000 (16:38 -0400)]
NLM,NFSv4: Don't put UNLOCK requests on the wire unless we hold a lock
Use the new behaviour of {flock,posix}_file_lock(F_UNLCK) to determine if
we held a lock, and only send the RPC request to the server if this was the
case.
Trond Myklebust [Thu, 29 Jun 2006 20:38:32 +0000 (16:38 -0400)]
VFS: Allow caller to determine if BSD or posix locks were actually freed
Change posix_lock_file_conf(), and flock_lock_file() so that if called
with an F_UNLCK argument, and the FL_EXISTS flag they will indicate
whether or not any locks were actually freed by returning 0 or -ENOENT.
asm-powerpc/cputime.h doesn't declare jiffies64_to_cputime64() or
cputime64_sub(), and due to CONFIG_VIRT_CPU_ACCOUNTING it's not picking
up the definition from asm-generic like x86-64 & friends do.
Cc: Dave Jones <davej@redhat.com> Cc: Andrew Morton <akpm@osdl.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With the new interrupt rework, an interrupt "host" map() callback can be
called after the interrupt is already active.
It's called again for an already mapped interrupt to allow changing the
trigger setup, and currently this is not guarded with a test of wether
the interrupt is requested or not.
I plan to change some of this logic to be a bit less lenient against
random reconfiguring of live interrupts but just not yet.
The ported MPIC driver has a bug where when that happens, it will mask
the interrupt. This changes it to preserve the previous masking of the
interrupt instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/cpufreq:
Move workqueue exports to where the functions are defined.
[CPUFREQ] Misc cleanups in ondemand.
[CPUFREQ] Make ondemand sampling per CPU and remove the mutex usage in sampling path.
[CPUFREQ] Add queue_delayed_work_on() interface for workqueues.
[CPUFREQ] Remove slowdown from ondemand sampling path.
[PATCH] fix AB-BA deadlock inversion at cs46xx_dsp_remove_scb
There is a code sequence where the locking is substream->self_group.lock
-> ins->scbs[index].lock
substream->self_group.lock is interrupt safe, and taken from irq context
as well (trace is snipped for brevity)
so what can happen is
cpu 0 cpu 1
user context user context
take ins->scbs[index].lock without disabling interrupts
get substream->self_group.lock (irqsafe)
try to get ins->scbs[index].lock (spins)
interrupt happens
try to get substream->self_group.lock (spins)
which is an obvious AB-BA deadlock
fix is to just take the lock with _irqsafe
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Cc: Jaroslav Kysela <perex@suse.cz> Acked-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Zach Brown [Tue, 4 Jul 2006 09:57:52 +0000 (02:57 -0700)]
[PATCH] mthca: initialize send and receive queue locks separately
mthca: initialize send and receive queue locks separately
lockdep identifies a lock by the call site of its initialization. By
initializing the send and receive queue locks in mthca_wq_init() we confuse
lockdep. It warns that that the ordered acquiry of both locks in
mthca_modify_qp() is recursive acquiry of one lock:
=============================================
[ INFO: possible recursive locking detected ]
---------------------------------------------
modprobe/1192 is trying to acquire lock:
(&wq->lock){....}, at: [<f892b4db>] mthca_modify_qp+0x60/0xa7b [ib_mthca]
but task is already holding lock:
(&wq->lock){....}, at: [<f892b4ce>] mthca_modify_qp+0x53/0xa7b [ib_mthca]
Initializing the locks separately in mthca_alloc_qp_common() stops the
warning and will let lockdep enforce proper ordering on paths that acquire
both locks.
Signed-off-by: Zach Brown <zach.brown@oracle.com> Cc: Roland Dreier <rolandd@cisco.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Cc: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] Fix copying of pgdat array on each node for ia64 memory hotplug
I found a bug in memory hot-add code for ia64.
IA64's code has copies of pgdat's array on each node to reduce memory
access over crossing node. This array is used by NODE_DATA() macro. When
new node is hot-added, this pgdat's array should be updated and copied on
new node too.
However, I used for_each_online_node() in scatter_node_data() to copy
it. This meant its array is not copied on new node.
Because initialization of structures for new node was halfway,
so online_node_map couldn't be set at this time.
To copy arrays on new node, I changed it to check value of pgdat_list[]
which is source array of copies. I tested this patch with my Memory Hotadd
emulation on Tiger4. This patch is for 2.6.17-git20.
Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] Ensure 8250_pci quirks are not marked __devinit
[SERIAL] Convert fifosize to an unsigned int
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
[Bluetooth] Add RFCOMM role switch support
[Bluetooth] Allow disabling of credit based flow control
[Bluetooth] Small cleanup of the L2CAP source code
[Bluetooth] Use real devices for host controllers
[Bluetooth] Add platform device for virtual and serial devices
[Bluetooth] Add automatic sniff mode support
[Bluetooth] Correct SCO buffer size on request
[Bluetooth] Add suspend/resume support to the HCI USB driver
[Bluetooth] Use raw mode for the Frontline sniffer device
[BRIDGE]: br_dump_ifinfo index fix
[ATM]: add+use poison defines
[NET]: add+use poison defines
[IOAT]: fix kernel-doc in source files
[IOAT]: fix header file kernel-doc
[TG3]: Add ipv6 TSO feature
[IPV6]: Fix ipv6 GSO payload length
[TIPC] Fixed sk_buff panic caused by tipc_link_bundle_buf (REVISED)
[NET]: Verify gso_type too in gso_segment
[IPVS]: Add sysctl documentation
[ROSE]: Try all routes when establishing a ROSE connections.
...
Fix incorrect usage of fsf_req_list_lock. It's used in tasklet context
(irqs on) as well as in irq context. Therefore use the spin_lock_irqsave
variant to avoid deadlocks.
Acked-by: Andreas Herrmann <aherrman@de.ibm.com> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With recent change, if CONFIG_HOTPLUG_CPU is disabled,
register_cpu_notifier() is not exported. And it breaked moduler msr/cpuid
(msr.c was already fixed).
We need to use register_hotcpu_notifier() now in module, instead of
register_cpu_notifier().
[Bluetooth] Allow disabling of credit based flow control
This patch adds the module parameter disable_cfc which can be used to
disable the credit based flow control. The credit based flow control
was introduced with the Bluetooth 1.1 specification and devices can
negotiate its support, but for testing purpose it is helpful to allow
disabling of it.
[Bluetooth] Small cleanup of the L2CAP source code
This patch is a small cleanup of the L2CAP source code. It makes some
coding style changes and moves some functions around to avoid forward
declarations.
This patch converts the Bluetooth class devices into real devices. The
Bluetooth class is kept and the driver core provides the appropriate
symlinks for backward compatibility.
projects / linux-2.6 / log