James Bottomley [Tue, 16 Aug 2005 23:27:34 +0000 (18:27 -0500)]
[SCSI] embryonic RAID class
The idea behind a RAID class is to provide a uniform interface to all
RAID subsystems (both hardware and software) in the kernel.
To do that, I've made this class a transport class that's entirely
subsystem independent (although the matching routines have to match per
subsystem, as you'll see looking at the code). I put it in the scsi
subdirectory purely because I needed somewhere to play with it, but it's
not a scsi specific module.
I used a fusion raid card as the test bed for this; with that kind of
card, this is the type of class output you get:
jejb@titanic> ls -l /sys/class/raid_devices/20\:0\:0\:0/
total 0
lrwxrwxrwx 1 root root 0 Aug 16 17:21 component-0 -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:1:0/20:1:0:0/
lrwxrwxrwx 1 root root 0 Aug 16 17:21 component-1 -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:1:1/20:1:1:0/
lrwxrwxrwx 1 root root 0 Aug 16 17:21 device -> ../../../devices/pci0000:80/0000:80:04.0/host20/target20:0:0/20:0:0:0/
-r--r--r-- 1 root root 16384 Aug 16 17:21 level
-r--r--r-- 1 root root 16384 Aug 16 17:21 resync
-r--r--r-- 1 root root 16384 Aug 16 17:21 state
So it's really simple: for a SCSI device representing a hardware raid,
it shows the raid level, the array state, the resync % complete (if the
state is resyncing) and the underlying components of the RAID (these are
exposed in fusion on the virtual channel 1).
As you can see, this type of information can be exported by almost
anything, including software raid.
The more difficult trick, of course, is going to be getting it to
perform configuration type actions with writable attributes.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The attached fixes this (but won't compile without the above).
It also fixes the logical reversal in the traversal loop which meant
that we were never actually traversing the loop to hit this bug in the
first place.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Mon, 22 Aug 2005 15:06:19 +0000 (10:06 -0500)]
[SCSI] correct attribute_container list usage
One of the changes in the attribute_container code in the scsi-misc tree
was to add a lock to protect the list of devices per container. This,
unfortunately, leads to potential scheduling while atomic problems if
there's a sleep in the function called by a trigger.
The correct solution is to use the kernel klist infrastructure instead
which allows lockless traversal of a list.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Pete Zaitcev [Wed, 6 Jul 2005 01:18:08 +0000 (18:18 -0700)]
[SCSI] sr.c: Fix getting wrong size
Here's the problem. Try to do this on 2.6.12:
- Kill udev and HAL
- Insert a CD-ROM into a SCSI or USB CD-ROM drive
- Run dd if=/dev/scd0
- cat /sys/block/sr0/size
- Eject the CD, insert a different one
- Run dd if=/dev/scd0
This is likely to do "access beyond the end of device", if you let it
- cat /sys/block/sr0/size
This shows the size of a previous CD, even though dd was supposed
to revalidate the device.
- Run dd if=/dev/scd0
The second run of dd works correctly!
The bug was introduced in 2.5.31, when Al fixes the recursive opens
in partitioning. Before, the code worked like this:
- Block layer called cdrom_open directly
- cdrom_open called sr_open
- sr_open called check_disk_change
- check_disk_change called sr_media_change
- sr_media_change did cd->needs_disk_change=1
- before returning sr_open tested cd->needs_disk_change
and called get_sector_size.
In 2.6.12, the check_disk_change is called from cdrom_open only. Thus:
- Block layer calls sr_bd_open
- sr_bd_open calls cdrom_open
- cdrom_open calls sr_open
- sr_open tests cd->needs_disk_change, which wasn't set yet; returns
- cdrom_open calls check_disk_change
- check_disk_change calls sr_media_change
- sr_media_change does cd->needs_disk_change=1, but nobody cares
Acked by: Alexander Viro <aviro@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Dave C Boutcher [Mon, 22 Aug 2005 19:38:26 +0000 (14:38 -0500)]
[SCSI] ibmvscsi timeout fix
This patch fixes a long term borkenness in
ibmvscsi where we were using the wrong timeout
field from the scsi command (and using the
wrong units.) Now broken by the fact that the
scsi_cmnd timeout field is gone entirely.
This only worked before because all the SCSI
targets assumed that 0 was default.
Signed-off-by: Dave Boutcher <boutcher@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Tue, 16 Aug 2005 22:26:10 +0000 (17:26 -0500)]
[SCSI] add missing attribute container function prototype
attribute_container_classdev_to_container is an exported function of the
attribute_container.c file. However, there's no prototype for it. Now
I actually want to use it, so add one.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Mon, 15 Aug 2005 21:13:19 +0000 (16:13 -0500)]
[SCSI] fix transport class corner case after rework
If your transport class sets the ATTRIBUTE_CONTAINER_NO_CLASSDEVS flag,
then its configure method never gets called. This patch fixes that so
that the configure method is called with a NULL classdev.
Also remove a spurious inverted comma in the transport_class comments.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Sun, 14 Aug 2005 22:09:01 +0000 (17:09 -0500)]
[SCSI] correct transport class abstraction to work outside SCSI
I recently tried to construct a totally generic transport class and
found there were certain features missing from the current abstract
transport class. Most notable is that you have to hang the data on the
class_device but most of the API is framed in terms of the generic
device, not the class_device.
These changes are two fold
- Provide the class_device to all of the setup and configure APIs
- Provide and extra API to take the device and the attribute class and
return the corresponding class_device
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Sun, 14 Aug 2005 19:34:06 +0000 (14:34 -0500)]
[SCSI] add ability to deny binding to SPI transport class
This patch is necessary if we begin exposing underlying physical disks
(which can attach to the SPI transport class) of the hardware RAID
cards, since we don't want any SPI parameters binding to the RAID
devices.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] lpfc driver 8.0.30 : convert to use of int_to_scsilun()
Replace use of lpfc_put_lun with midlayer's int_to_scsilun
Remove driver's local definition of lpfc_put_lun (which converts an
int back to a 64-bit LUN) and replace it's use with the recently added
int_to_scsilun function provided by the midlayer.
Note: Embedding midlayer structure in our structure caused
need for more files to include midlayer headers.
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] lpfc driver 8.0.30 : dev_loss and nodev timeouts
Fix handling of the dev_loss and nodev timeouts.
Symptoms: when remote port disappears for a period of time longer then
either nodev_tmo or dev_loss_tmo, the lpfc driver worker thread will
stall removing that remote port.
Cause: removing remote port involves un-blocking and sync-ing
corresponding block device queue. But corresponding node in the lpfc
driver is still in the NPR(?node port recovery?) state and mid-layer
gets SCSI_MLQUEUE_HOST_BUSY as a return value when it is trying to call
queuecommand() with command for that node (AKA remote port)
Fix: Instead of returning SCSI_MLQUEUE_HOST_BUS from queuecommand() for
nodes in NPR states complete it with retry-able error code DID_BUS_BUSY
Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Tue, 9 Aug 2005 17:57:11 +0000 (12:57 -0500)]
[SCSI] Make the HSG80 a REPORTLUN2 device
From: Steve Wilcox <spwilcox@att.com>
In order to properly report LUN's > 7, the DEC HSG80 definition in
scsi_devinfo.c needs to include BLIST_REPORTLUN2 rather than
BLIST_SPARSELUN. I've tested this change with several HSG firmware
revisions and with both Emulex and Qlogic HBA's.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Tue, 9 Aug 2005 00:06:50 +0000 (19:06 -0500)]
[SCSI] aic79xx: fix boot panic with no hardware
There's a spurious (and illegal since it's marked __exit) call to
ahc_linux_exit() in ahc_linux_init() which causes a double list
deletion of the transport class; remove it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Dave Jones [Mon, 8 Aug 2005 23:01:43 +0000 (19:01 -0400)]
[SCSI] blacklist addition.
When run on a kernel that scans all LUNs, a certain crappy
scsi scanner reports the same LUN over and over..
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=155457
Aparently they were so shamed by this, they chose to remain
anonymous. Though it seems the blacklist code handles
anonymous vendors just fine.
Signed-off-by: Dave Jones <davej@redhat.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Sat, 6 Aug 2005 02:45:40 +0000 (21:45 -0500)]
[SCSI] add global timeout to the scsi mid-layer
There are certain rogue devices (and the aic7xxx driver) that return
BUSY or QUEUE_FULL forever. This code will apply a global timeout (of
the total number of retries times the per command timer) to a given
command. If it is exceeded, the command is completed regardless of its
state.
The patch also removes the unused field in the command: timeout and
timeout_total.
This solves the problem of detecting an endless loop in the mid-layer
because of BUSY/QUEUE_FULL bouncing, but will not recover the device.
In the aic7xxx case, the driver can be recovered by sending a bus reset,
so possibly this should be tied into the error handler?
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Kai Makisara [Tue, 2 Aug 2005 10:40:47 +0000 (13:40 +0300)]
[SCSI] drivers/scsi/st.c: add reference count and related fixes
I have rediffed the patch against 2.6.13-rc5, done a couple of cosmetic
cleanups, and run some tests. Brian King has acknowledged that it fixes the
problems he has seen. Seems mature enough for inclusion into 2.6.14 (or
later)?
Nate's explanation of the changes:
I've attached patches against 2.6.13rc2. These are basically identical
to my earlier patches, as I found that all issues I'd seen in earlier
kernels still existed in this kernel.
To summarize, the changes are: (more details in my original email)
- add a kref to the scsi_tape structure, and associate reference
counting stuff
- set sr_request->end_io = blk_end_sync_rq so we get notified when an IO
is rejected when the device goes away
- check rq_status when IOs complete, else we don't know that IOs
rejected for a dead device in fact did not complete
- change last_SRpnt so it's set before an async IO is issued (in case
st_sleep_done is bypassed)
- fix a bogus use of last_SRpnt in st_chk_result
Signed-off-by: Nate Dailey <nate.dailey@stratus.com> Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Fri, 5 Aug 2005 21:31:35 +0000 (16:31 -0500)]
[SCSI] aacraid: correct use of cmd->timeout field
The cmd->timeout field has been obsolete for a while now. While looking
to remove it, I came across this use in the aacraid driver. It looks
like you want to initialise the firmware with the current timeout of the
command (in seconds), so the value I think you should be using is
cmd->timeout_per_command.
Acked by: Mark Haverkamp <markh@osdl.org>
Acked by: Mark Salyzyn <mark_salyzyn@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
akpm@osdl.org [Sun, 7 Aug 2005 06:32:07 +0000 (23:32 -0700)]
[SCSI] aic79xx: needs to select SPI_TRANSPORT_ATTRS
without it you get this failure:
drivers/built-in.o(.text+0xdcccd): In function `ahd_linux_slave_configure':
drivers/scsi/aic7xxx/aic79xx_osm.c:636: undefined reference to `spi_dv_device'
drivers/built-in.o(.text+0xdd7b1): In function `ahd_send_async':
drivers/scsi/aic7xxx/aic79xx_osm.c:1652: undefined reference to `spi_display_xfer_agreement'
drivers/built-in.o(.init.text+0x7b4d): In function `ahd_linux_init':
drivers/scsi/aic7xxx/aic79xx_osm.c:2765: undefined reference to `spi_attach_transport'
drivers/built-in.o(.init.text+0x7c94):drivers/scsi/aic7xxx/aic79xx_osm.c:2774: undefined reference to `spi_release_transport'
drivers/built-in.o(.exit.text+0x72c): In function `ahd_linux_exit':
drivers/scsi/aic7xxx/aic79xx_osm.c:2783: undefined reference to `spi_release_transport'
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 3 Aug 2005 22:39:49 +0000 (15:39 -0700)]
[SCSI] aacraid: sgraw command support
Received from Mark Salyzyn from Adaptec:
This patch adds support for the new raw io command. This new command
offers much larger io commands, is more friendly to the internal firmware
structure requiring less translation efforts by the firmware and offers
support for targets greater than 2TB (patch to support >2TB will
be sent in the future).
Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 3 Aug 2005 22:39:25 +0000 (15:39 -0700)]
[SCSI] aacraid: aif registration timeout fix
Received from Mark Salyzyn from Adaptec:
If the Adapter is quiet and does not produce an AIF event packets to be
picked up by the management applications for longer than the timeout
interval of two minutes, the cleanup code that deals with aging out
registrants could erroneously drop the registration. The timeout is
there to clean up should the management application die and fail to poll
for updated AIF event packets.
Moving the timer update from the ioctl code that delivers an AIF to the
polling registrant to the bottom of the ioctl means the timeout is reset
with any management application polling activity regardless if an AIF is
delivered or not removing the erroneous timeout cleanups.
Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 3 Aug 2005 22:39:09 +0000 (15:39 -0700)]
[SCSI] aacraid: remove duplicate io callback code
Received from Mark Salyzyn from Adaptec:
This patch removes the duplicate code in the write_callback command
completion handler, and renames read_callback to io_callback. Optimized
the lba calculation into the debug print routine macro to optimize the
i/o code path.
Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 3 Aug 2005 22:39:01 +0000 (15:39 -0700)]
[SCSI] aacraid: driver shutdown method
Add in pci shutdown method so that the adapter shuts down correctly and
flushes its cache. Shutdown should also disable the adapter's interrupt
when shutdown (in particularly if the driver is rmmod'd) to prevent
spurious hardware activities.
Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 3 Aug 2005 22:38:55 +0000 (15:38 -0700)]
[SCSI] aacraid: driver version update
Received from Mark Salyzyn from Adaptec.
Fixes a bug in check_revision. It should return the driver version not
the firmware version.
Update driver version number.
Update driver version string.
Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mark Haverkamp [Wed, 3 Aug 2005 22:38:51 +0000 (15:38 -0700)]
[SCSI] aacraid: interupt mitigation
Received from Mark Salyzyn from Adaptec:
If more than two commands are outstanding to the controller, there is no
need to notify the adapter via a PCI bus transaction of additional
commands added into the queue; it will get to them when it works through
the produce/consumer indexes.
This reduced the PCI traffic in the driver to submit a command to the
queue to near zero allowing a significant number of commands to be
turned around with no need to block for the PCI bridge to flush the
notify request to the adapter.
Interrupt mitigation has always been present in the driver; it was
turned off because of a bug that prevented one from realizing the
usefulness of the feature. This bug is fixed in this patch.
Signed-off-by: Mark Haverkamp <markh@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hannes Reinecke [Thu, 4 Aug 2005 07:16:59 +0000 (09:16 +0200)]
[SCSI] aic79xx: fixup DT setting
this patch is just a cross-port of the fixup for aic7xxx DT settings.
As the same restrictions apply for aic79xx also (DT requires wide
transfers) the dt setting routine should be modified equivalently.
And an invalid period setting will be caught by ahd_find_syncrate()
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Wed, 3 Aug 2005 20:43:52 +0000 (15:43 -0500)]
[SCSI] add missing hold_mcs parameter to the spi transport class
This parameter is important only to people who take the time to tune the
margin control settings, otherwise it's completely irrelevant. However,
just in case anyone should want to do this, it's appropriate to include
the parameter.
I don't do anything with it in DV by design, so the parameter will come
up as off by default, so if anyone actually wants to play with the
margin control settings they'll have to enable it under the
spi_transport class first.
I also updated the transfer settings display to report all of the PPR
settings instead of only DT, IU and QAS
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
James Bottomley [Wed, 3 Aug 2005 18:25:10 +0000 (13:25 -0500)]
[SCSI] aic79xx: fix up transport settings
There's a slight problem in the way you've done the transport
parameters; reading from the variables actually produces the current
settings, not the ones you just set (and there's usually a lag because
devices don't renegotiate until the next command goes over the bus). If
you set the bit immediately, you get into the situation where the
transport parameters report something as being set even if the drive
cannot support it.
I patched the driver to do it this way and also corrected a panic in the
proc routines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hannes Reinecke [Mon, 1 Aug 2005 07:52:56 +0000 (09:52 +0200)]
[SCSI] aic79xx: DV parameter settings
This patch updates various scsi_transport_spi parameters with the actual
parameters used by the driver internally.
Domain Validation for all devices should now work properly.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hannes Reinecke [Fri, 22 Jul 2005 14:44:04 +0000 (16:44 +0200)]
[SCSI] aic79xx: update to use scsi_transport_spi
This patch updates the aic79xx driver to take advantage of the
scsi_transport_spi infrastructure. Patch is quite a mess as some
procedures have been reshuffled to be closer to the aic7xxx driver.
Rejections fixed and Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mike Anderson [Thu, 16 Jun 2005 18:13:42 +0000 (11:13 -0700)]
[SCSI] host state model update: reimplement scsi_host_cancel
Remove the old scsi_host_cancel function as it has not been working for
sometime do to the device list possibly being empty when it is called and
possible race issues. Add setting of SHOST_CANCEL at the state of beginning
of scsi_remove_host.
Signed-off-by: Mike Anderson <andmike@us.ibm.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It seems very unlikely that this driver will go into any stable kernel
before devfs will be removed.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Matthew Garrett [Fri, 29 Jul 2005 21:03:39 +0000 (14:03 -0700)]
[PATCH] agp: restore APBASE after setting APSIZE
When leaving S3 state, the AGP bridge may not have all PCI configuration
registers set in the same way as they were at boot. This should be fixed
by pci_restore_state - however, the APBASE register cannot be set to
conflict with the APSIZE register. If APSIZE is larger than it was before
suspend, pci_restore_state will not restore APBASE correctly. The attached
patch adds an extra item to the agp_bridge_data structure and uses it to
store the value of APBASE. On resume, this is then written after APSIZE
has been set. This patch only touches the path used for Intel chipsets
without integrated graphics, and may need to be extended to work with the
others.
Without this patch, I get the symptoms described in bug 4921 - APBASE ends
up overlapping various PCI devices, and as a result they fail to work after
resume.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org> Acked-by: Dave Jones <davej@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Close a small window where a device may be not operational again after senseid
finished and the "same device" check fails due to dev=0000 by checking for dnv
after stsch() by then setting the device to not operational. (No need to
check for dnv in ccw_device_handle_oper() again since we don't do stsch() into
the subchannel's schib in the meantime and will get a crw anyway if the device
becomes not oper again).
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch that introduced waiting for interrupts after resetting the reader
can cause the boot to fail because the system is waiting for an interrupt that
will never arrive. Add code to check if an interrupt is supposed to arrive
before waiting endlessly.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Fri, 29 Jul 2005 21:03:33 +0000 (14:03 -0700)]
[PATCH] uml: fix vsyscall brokenness
The #if/#ifdef cleanup exposed a bug in UML's ELF header processing. With
this bug fixed, UML recognizes the vsyscall info coming from the host. On
FC4, there is a vsyscall page low in the address space, which UML doesn't
provide. This causes an infinite page fault loop and a hang on boot.
This patch works around that by making this look like a no-vsyscall system.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device. The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided. Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up. The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices. The patch corrects this
problem by allowing PCI IRQs below 16.
sync_tsc was using smp_call_function to ask the boot processor to report
it's tsc value. smp_call_function performs an IPI_send_allbutself which is
a broadcast ipi. There is a window during processor startup during which
the target cpu has started and before it has initialized it's interrupt
vectors so it can properly process an interrupt. Receveing an interrupt
during that window will triple fault the cpu and do other nasty things.
Why cli does not protect us from that is beyond me.
The simple fix is to match ia64 and provide a smp_call_function_single.
Which avoids the broadcast and is more efficient.
This certainly fixes the problem of getting stuck on boot which was
very easy to trigger on my SMP Hyperthreaded Xeon, and I think
it fixes it for the right reasons.
Minor changes by AK
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] mm: Ensure proper alignment for node_remap_start_pfn
While reserving KVA for lmem_maps of node, we have to make sure that
node_remap_start_pfn[] is aligned to a proper pmd boundary.
(node_remap_start_pfn[] gets its value from node_end_pfn[])
Dan Streetman [Fri, 29 Jul 2005 19:18:28 +0000 (12:18 -0700)]
[PATCH] USB: fix in usb_calc_bus_time
This patch does the same swap, i.e. use the ISO macro if (isoc).
Additionally, it fixes the return value - the usb_calc_bus_time function
returns the time in nanoseconds (I didn't notice that before) while the
HS_USECS and HS_USECS_ISO are microseconds. This fixes the function to
return nanoseconds always, and adjusts ehci-q.c (the only high-speed
caller of the function) to wrap the call in NS_TO_US().
Gigabyte GN-WLBZ201 wifi usb dongle works very well, using the zd1201
driver. the only missing part is that the corresponding usbid is not
declared. The following patch should fix this.
This patch enables a support of KYOCERA AH-K3001V, one of the most
popular cell phone in Japan. This device has vendor specific ID but works
with acm driver by adding USB ID. This device already works on
FreeBSD and OS X by native USB ACM driver with USB ID added.
This device is probed as NO_UNION_NORMAL not to hang up when probing.
Alan Stern [Fri, 29 Jul 2005 19:17:16 +0000 (12:17 -0700)]
[PATCH] USB: Usbcore: Don't try to delete unregistered interfaces
This patch handles a rarely-encountered failure mode in usbcore. It's
legal for device_add to fail (although now it happens even more rarely
than before since failure to bind a driver is no longer fatal). So when
we destroy the interfaces in a configuration, we shouldn't try to delete
ones which weren't successfully registered. Also, failure to register an
interface shouldn't be fatal either -- I think; you may disagree about
this part of the patch.
Alan Stern [Fri, 29 Jul 2005 19:16:58 +0000 (12:16 -0700)]
[PATCH] USB: usbfs: Don't leak uninitialized data
This patch fixes an information leak in the usbfs snoop facility:
uninitialized data from __get_free_page can be returned to userspace and
written to the system log. It also improves the snoop output by printing
the wLength value.
Ian Abbott [Fri, 29 Jul 2005 19:16:41 +0000 (12:16 -0700)]
[PATCH] USB: ftdi_sio: Update RTS and DTR simultaneously
ftdi_sio: Update RTS and DTR simultaneously, using a single control URB
instead of separate control URBs for RTS and DTR. Reinhard Bergmann
observed time differences of up to 680 ms with his application on a
2.4.22 kernel when RTS and DTR were updated using separate control
URBs, which is unacceptable.
Ivan Kokshaysky [Fri, 29 Jul 2005 19:16:22 +0000 (12:16 -0700)]
[PATCH] PCI: remove PCI_BRIDGE_CTL_VGA handling from setup-bus.c
The setup-bus code doesn't work correctly for configurations
with more than one display adapter in the same PCI domain.
This stuff actually is a leftover of an early 2.4 PCI setup code
and apparently it stopped working after some "bridge_ctl" changes.
So the best thing we can do is just to remove it and rely on the fact
that any firmware *has* to configure VGA port forwarding for the boot
display device properly.
But then we need to ensure that the bus->bridge_ctl will always
contain valid information collected at the probe time, therefore
the following change in pci_scan_bridge() is needed.
Jon Smirl [Fri, 29 Jul 2005 19:16:17 +0000 (12:16 -0700)]
[PATCH] PCI: Adjust PCI rom code to handle more broken ROMs
There are ROMs reporting that their size exceeds their PCI ROM
resource window. This patch returns the minimum of the resource window
size or the size in the ROM. An example of this breakage is the XGI
Volari Z7.
This patch was sent first time very long time ago,
but magically was disapeared, it probably exists
in your queue, but to be sure, I resend it.
If can not be applied cleanly after your w1 queue is flushed
into upstrem tree, just drop it.
Thanks.
Patch from Michael Farmbauer <michl@baldrian.franken.de>.
Jean Delvare [Fri, 29 Jul 2005 19:15:33 +0000 (12:15 -0700)]
[PATCH] I2C: 24RF08 corruption prevention (again)
The 24RF08 corruption prevention in the eeprom and max6875 drivers wasn't
complete. For one thing, the additional quick write should happen as soon
as possible and unconditionally, while both drivers had error paths before.
For another, when a given chip is forced, the core does not emit a quick
write, so a second quick write would cause the corruption rather than
prevent it.
I plan to move the corruption prevention in the core in the long run, so
that individual drivers don't have to care anymore. But I need to merge
i2c_probe and i2c_detect before I do (work in progress).
Jean Delvare [Fri, 29 Jul 2005 19:15:07 +0000 (12:15 -0700)]
[PATCH] I2C: Missing space in split strings
A few split string in i2c (and now hwmon) drivers lack a joining space,
causing them to display incorrectly. This trivial patch fixes that up.
Please apply, thanks.
Ladislav Michl [Fri, 29 Jul 2005 19:15:00 +0000 (12:15 -0700)]
[PATCH] I2C: ds1337 - fix 12/24 hour mode bug
DS1339 manual, page 6, chapter Date and time operation:
The DS1339 can be run in either 12-hour or 24-hour mode. Bit 6 of the
hours register is defined as the 12-hour or 24-hour mode-select bit.
When high, the 12-hour mode is selected.
Patch below makes ds1337 driver work as documented in manual.
projects / linux-2.6 / log