* Rename 'simplex_stat' variable to 'dma_stat' in ide_get_or_set_dma_base().
* Factor out code for forcing host out of "simplex" mode from
ide_get_or_set_dma_base() to ide_pci_clear_simplex() helper.
* Add IDE_HFLAG_CLEAR_SIMPLEX host flag and set it in alim15x3 (for M5229),
amd74xx (for AMD 7409), cmd64x (for CMD643), generic (for Netcell) and
serverworks (for CSB5) host drivers.
* Make ide_get_or_set_dma_base() test for IDE_HFLAG_CLEAR_SIMPLEX host flag
instead of checking dev->device (BTW the code was buggy because it didn't
check for dev->vendor, luckily none of these PCI Device IDs was used by
some other vendor for PCI IDE controller).
* Remove no longer needed assertion from amd74xx_probe().
* Factor out cable detection for AMD7409 to amd7409_cable_detect() and for
chipsets >= AMD7411 to amd7411_cable_detect().
* Use dev->vendor and dev->device instead of amd_config->udma_mask when
selecting cable detection method and checking for broken FIFO support in
init_chipset_amd74xx().
* Remove no longer needed AMD_BAD_FIFO define.
* Add 'swdma' parameter for setting .swdma_mask to DECLARE_AMD_DEV() macro.
* Add 'udma' parameter for setting .udma_mask to DECLARE_{AMD,NV}_DEV() macro.
* Keep a copy of a current amd74xx_chipsets[] entry in amd74xx_probe()
in order to fix ->swdma_mask on early AMD7409 revisions and ->udma_mask
on Serenade mainboards.
* Remove no longer needed fixups from init_chipset_amd74xx()
and AMD_CHECK_{SWDMA,SERENADE} defines.
* Move printing banner message from init_chipset_amd74xx() to amd74xx_probe(),
also remove incorrect comment while at it.
* Use hwif->ultra_mask instead of amd_config->udma_mask in amd_set_drive().
* Add 'udma_mask' argument to amd_set_speed() and pass UDMA mask from
amd_set_drive() instead of using amd_config->udma_mask.
* Move amd_config->base from AMD_* defines to users of these defines and add
0x40 the defined values. Then add amd_offset() inline helper for selecting
offset from 0x40 base (needed for nVidia controllers) and finally use it in
amd_set_speed(), amd7411_cable_detect() and init_chipset_amd74xx() instead
of amd_config->base.
* Remove no longer needed AMD_BAD_SWDMA define, ->{swdma,ultra}_mask setup
from init_hwif_amd74xx(), amd_{config,chipset} variables and amd_ide_chips
table.
* Fix init_chipset_amd74xx() comment.
* Bump driver version.
There should be no functionality changes caused by this patch.
Sergei Shtylyov [Fri, 1 Feb 2008 22:09:30 +0000 (23:09 +0100)]
ide: ide_setup_dma() assumes 8 ports
According to http://marc.info/?l=linux-ide&m=114346138611631, the drivers must
always register 8 DMA ports with ide_setup_dma(), so its last argument is not
needed. While at it, kill some useless parens in that function...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide-{floppy,tape}: remove debug code for dumping identify data
IDE core supports dumping raw identify data in hdparm friendly format now
so verbose identify dumping in ide-{floppy,tape}.c device drivers (done iff
IDE{FLOPPY,TAPE}_DEBUG_INFO is defined to '1' and it is '0' by default)
is no longer nedeed.
* Add ide_dump_identify() debug helper for dumping raw identify data in
the hdparm friendly format (== the identify data can be extracted from
dmesg output and passed to hdparm --Istdin).
* Dump identify data in ide-probe.c::do_identify() if DEBUG is enabled.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide-cd: merge cdrom_write_check_ireason() and cdrom_read_check_ireason()
Add 'rw' parameter to cdrom_read_check_ireason(), make it handle
both read and write checking, rename it to ide_cd_check_ireason(),
finally remove no longer needed cdrom_write_check_ireason().
There should be no functionality changes caused by this patch.
ide-cd: prepare cdrom_rw_intr() and cdrom_newpc_intr() to be merged
In cdrom_newpc_intr():
* cleanup variables in the 'transfer data' loop
In cdrom_rw_intr():
* rename 'sectors_to_transfer' to 'thislen'
* rename 'this_transfer' to 'blen'
* keep number of bytes (instead of sectors) in 'thislen' and 'blen'
* call 'xferfunc' only once for 'blen'
* cache 'rq->buffer' in 'ptr' variable
* check for 'rq->bio' before setting 'ptr' and 'blen'
* check for 'ptr' instead of 'rq->current_nr_sectors'
There should be no functionality changes caused by this patch.
ide-cd: merge cdrom_start_read_continuation() and cdrom_start_rw_cont()
* Add handling of write requests to cdrom_start_read_continuation(),
rename it to cdrom_start_rw_cont() and remove no longer needed
cdrom_start_write_cont().
ide-cd: merge cdrom_pc_intr() and cdrom_newpc_intr()
Add handling of REQ_TYPE_{SENSE,ATA_PC} requests to cdrom_newpc_intr()
(please note that these requests never have 'bio' attached to them
and they never use DMA), then remove no longer needed cdrom_pc_intr().
There should be no functionality changes caused by this patch.
ide-cd: move VERBOSE_IDE_CD_ERRORS code to ide-cd_verbose.c
* Rename ide-cd kernel module to ide-cd_mod in preparation to moving code out
from ide-cd.[c,h]. Add MODULE_ALIAS("ide-cd") to preserve compatibility.
* Move VERBOSE_IDE_CD_ERRORS code from ide-cd.[c,h] to ide-cd_verbose.c.
ide-cd_verbose.c is IDE subsystem independent and may be easily converted
into generic library usable by other drivers (i.e. libata) if needed.
* Add CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS config option to drivers/ide/Kconfig
replacing VERBOSE_IDE_CD_ERRORS define. Make this config option enabled by
default and visible only if CONFIG_EMBEDDED is defined.
before the patch:
text data bss dec hex filename
22841 360 1056 24257 5ec1 drivers/ide/ide-cd.o
after the patch w/ CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=y:
text data bss dec hex filename
22857 360 1056 24273 5ed1 drivers/ide/ide-cd_mod.o
after the patch w/ CONFIG_BLK_DEV_IDECD_VERBOSE_ERRORS=n:
text data bss dec hex filename
15091 360 1056 16507 407b drivers/ide/ide-cd_mod.o
Adrian Bunk [Fri, 1 Feb 2008 22:09:16 +0000 (23:09 +0100)]
ide/ppc/pmac.c section fixes
This patch fixes the following section mismatch:
<-- snip -->
...
WARNING: vmlinux.o(.text+0x3b641c): Section mismatch in reference from the function .pmac_ide_setup_device() to the function .init.text:.pmac_ide_setup_dma()
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Frans Pop [Fri, 1 Feb 2008 22:09:16 +0000 (23:09 +0100)]
ide/Kconfig: use 'on-board' instead of 'built-in' in config options
To avoid confusion between 'built-in' drivers and 'on-board'
controllers, consistently use the term 'on-board' for controllers.
Minor line-wrapping improvements in descriptions for config options.
[ Bart: thanks to Jan for 'built-in'->'on-board' suggestion ]
Signed-off-by: Frans Pop <elendil@planet.nl> Cc: Jan Engelhardt <jengelh@computergmbh.de> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
ide: drop 'initializing' argument from ide_register_hw()
* Rename init_hwif_data() to ide_init_port_data() and export it.
* For all users of ide_register_hw() with 'initializing' argument set
hwif->present and hwif->hold are always zero so convert these host
drivers to use ide_find_port()+ide_init_port_data()+ide_init_port_hw()
instead (also no need for init_hwif_default() call since the setup
done by it gets over-ridden by ide_init_port_hw() call).
* Drop 'initializing' argument from ide_register_hw().
introduced the usage of a hwif variable, but forgot to declare the actual
variable.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Linus Torvalds [Fri, 1 Feb 2008 10:48:45 +0000 (21:48 +1100)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: kill swap_io_context()
as-iosched: fix inconsistent ioc->lock context
ide-cd: fix leftover data BUG
block: make elevator lib checkpatch compliant
cfq-iosched: make checkpatch compliant
block: make core bits checkpatch compliant
block: new end request handling interface should take unsigned byte counts
unexport add_disk_randomness
block/sunvdc.c:print_version() must be __devinit
splice: always updated atime in direct splice
Greg Ungerer [Fri, 1 Feb 2008 07:38:24 +0000 (17:38 +1000)]
m68knommu: fix 528x ColdFire cache settings
Fix problems with the 528x ColdFire CPU cache setup.
Do not cache the flash region (if present), and make the runtime
settings consistent with the init setting.
Problems pointed out by Bernd Buttner <b.buettner@mkc-gmbh.de>
Greg Ungerer [Fri, 1 Feb 2008 07:38:03 +0000 (17:38 +1000)]
m68knommu: create common DMA table for ColdFire CPUs
Move the ColdFire DMA address table into its own file, and out
of each of the different CPU config files. No need to have a copy
of it in each of the config setup files.
Greg Ungerer [Fri, 1 Feb 2008 07:37:56 +0000 (17:37 +1000)]
m68knommu: modify Makefiles to support common coldfire directory
Modify Makefiles to support separate coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:37:46 +0000 (17:37 +1000)]
m68knommu: move ColdFire vectors.c to its own coldfire directory
Move common ColdFire CPU vectors.c to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:37:39 +0000 (17:37 +1000)]
m68knommu: move ColdFire timers.c to its own coldfire directory
Move common ColdFire CPU timers.c to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:37:36 +0000 (17:37 +1000)]
m68knommu: move ColdFire pit.c to its own coldfire directory
Move common ColdFire CPU pit.c to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:37:28 +0000 (17:37 +1000)]
m68knommu: move ColdFire head.S to its own coldfire directory
Move common ColdFire CPU head.S to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
Greg Ungerer [Fri, 1 Feb 2008 07:37:18 +0000 (17:37 +1000)]
m68knommu: move ColdFire entry.S to its own coldfire directory
Move common ColdFire CPU entry.S to common coldfire platform directory.
Currently the common ColdFire CPU family code sits in the
arch/m68knommu/platform/5307 directory. This is confusing, the files
containing this common code are in no way specific to the 5307 ColdFire.
Create an arch/m68knommu/platform/coldfire directory to contain this
common code. Other m68knommu CPU varients do not need use this code
though, so it doesn't make sense to move it to arch/m68knommu/kernel.
projects / linux-2.6 / log