This patch adds code to fix up the PHYMODE4 "align timing"
register value on second-generation Promise SATA chips.
Failure to correct this value on non-x86 machines makes
drive detection prone to failure due to timeouts. (I've
observed about 50% detection failure rates on SPARC64.)
The HW boots with a bad value in this register, but on x86
machines the Promise BIOS corrects it to the value recommended
by the manual, so most people have been unaffected by this issue.
After developing the patch I checked Promise's SATAII driver,
and discovered that it also corrects PHYMODE4 just like this
patch does.
This patch depends on the sata_promise SATAII updates
patch I sent recently.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Sun, 3 Dec 2006 12:34:13 +0000 (21:34 +0900)]
[PATCH] libata: always use polling IDENTIFY
libata switched to IRQ-driven IDENTIFY when IRQ-driven PIO was
introduced. This has caused a lot of problems including device
misdetection and phantom device.
ATA_FLAG_DETECT_POLLING was added recently to selectively use polling
IDENTIFY on problemetic drivers but many controllers and devices are
affected by this problem and trying to adding ATA_FLAG_DETECT_POLLING
for each such case is diffcult and not very rewarding.
This patch makes libata always use polling IDENTIFY. This is
consistent with libata's original behavior and drivers/ide's behavior.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 20 Nov 2006 06:42:36 +0000 (15:42 +0900)]
[PATCH] ahci: do not powerdown during initialization
ahci_init_controller() calls ahci_deinit_port() to make sure the
controller is stopped before initializing the controller. In turn,
ahci_deinit_port() invokes ahci_power_down() to power down the port.
If the controller supports slumber mode, the link is put into it.
Unfortunately, some devices don't implement link powersaving mode
properly and show erratic behavior after link is put into slumber
mode. For example, HL-DT-ST DVD-RAM GSA-H30N completely locks up on
slumber transition and can only be recovered with the *REAL* hard
reset - power removal and reapply.
Note that this makes the first probing reset different from all
others. If the above dvd-ram is hotplugged after ahci is initialized,
no problem occurs because ahci is already fully initialized with phy
powered up. So, this might also be the reason for other weird AHCI
initial probing abnormalities.
This patch moves power up/down out of port init/deinit and call them
only when needed.
Power down is now called only when suspending. As system suspend
usually involves powering down 12v for storage devices, this shouldn't
cause problem even if the attached device doesn't support slumber
mode. However, in partial power management and suspend failure cases,
devices might lock up after suspend attempt. I thought about removing
transition to slumber mode altogether but ahci spec mandates it before
HBA D3 state transition. Blacklisting such devices might be the
solution.
Tejun Heo [Tue, 14 Nov 2006 13:47:09 +0000 (22:47 +0900)]
[PATCH] libata: implement ata_exec_internal_sg()
Sg'ify ata_exec_internal() and call it ata_exec_internal_sg().
Wrapper function around ata_exec_internal_sg() is implemented to
provide ata_exec_internal() interface.
Tejun Heo [Fri, 17 Nov 2006 03:24:22 +0000 (12:24 +0900)]
[PATCH] libata: make sure IRQ is cleared after ata_bmdma_freeze()
Now that BMDMA status is recorded in irq handler. ata_bmdma_freeze()
is free to manipulate host status. Under certain circumstances, some
controllers (ICH7 in enhanced mode w/ IRQ shared) raise IRQ when CTL
register is written to and ATA_NIEN doesn't mask it.
This patch makes ata_bmdma_freeze() clear all pending IRQs after
freezing a port. This change makes explicit clearing in
ata_device_add() unnecessary and thus kills it. The removed code was
SFF-specific and was in the wrong place.
Note that ->freeze() handler is always called under ap->lock held and
irq disabled. Even if CTL manipulation causes stuck IRQ, it's cleared
immediately. This should be safe (enough) even in SMP environment.
More correct solution is to mask the IRQ from IRQ controller but that
would be an overkill.
Tejun Heo [Fri, 17 Nov 2006 03:06:21 +0000 (12:06 +0900)]
[PATCH] libata: move BMDMA host status recording from EH to interrupt handler
For certain errors, interrupt handler alter BMDMA host status before
entering EH (clears active and intr). Thus altered BMDMA host status
value is recorded by BMDMA EH and reported to user. Move BMDMA host
status recording from EH to interrupt handler.
Tejun Heo [Tue, 21 Nov 2006 01:40:51 +0000 (10:40 +0900)]
[PATCH] libata: don't request sense if the port is frozen
If EH command is issued to a frozen port, it fails with AC_ERR_SYSTEM.
libata used to request sense even when the port is frozen needlessly
adding AC_ERR_SYSTEM to err_mask. Don't do it.
Tejun Heo [Mon, 20 Nov 2006 02:15:47 +0000 (11:15 +0900)]
[PATCH] libata: fix READ CAPACITY simulation
* READ CAPACITY (16) implementation fixed. Result was shifted by two
bytes. Carlos Pardo spotted this problem and submitted preliminary
patch. Capacity => 2TB is handled correctly now. (verifid w/ fake
capacity)
* Use dev->n_sectors instead of re-reading directly from ID data.
* Define and use ATA_SCSI_RBUF_SET() which considers rbuf length.
This should be done for all simulation functions. Userland can
issue any simulated command with arbitrary buffer length.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Carlos Pardo <Carlos.Pardo@siliconimage.com>
Tejun Heo [Thu, 16 Nov 2006 01:50:50 +0000 (10:50 +0900)]
[PATCH] libata: implement ATA_FLAG_SETXFER_POLLING and use it in pata_via, take #2
This patch implements ATA_FLAG_SETXFER_POLLING and use in pata_via.
If this flag is set, transfer mode setting performed by polling not by
interrupt. This should help those controllers which raise interrupt
before the command is actually complete on SETXFER.
Rationale for this approach.
* uses existing facility and relatively simple
* no busy sleep in the interrupt handler
* updating drivers is easy
While at it, kill now unused flag ATA_FLAG_SRST in pata_via.
Tejun Heo [Fri, 17 Nov 2006 07:22:27 +0000 (16:22 +0900)]
[PATCH] libata: set IRQF_SHARED for legacy PCI IDE IRQs
There are machines out there which share legacy PCI IDE IRQs w/ other
devices. libata SFF interrupt/HSM code is ready for shared IRQ and
has been setting IRQF_SHARED for devices in native PCI mode. Device
in legacy mode is still a PCI device and thus supposedly uses
active-low level triggered IRQ.
Machines with such setup should be quite rare and w/o this flag libata
is likely to fail loading and render the system unuseable. Also, IDE
driver has been setting IRQF_SHARED for devices in legacy mode for a
looooong time.
Tejun Heo [Fri, 17 Nov 2006 03:05:11 +0000 (12:05 +0900)]
[PATCH] libata: remove unused HSM_ST_UNKNOWN
HSM_ST_UNKNOWN is not used anywhere. Its value is zero and supposed
to serve sanity check purpose but HSM_ST_IDLE is used for that
purpose. This unused state causes confusion. After a port is
initialized but before the first command is executed, the idle hsm
state is UNKNOWN. However, once a command has completed, the idle hsm
state is IDLE. This defeats sanity check in ata_pio_task() for the
first command.
This patch removes HSM_ST_UNKNOWN and consequently make HSM_ST_IDLE
the default state.
Robert Hancock [Sun, 26 Nov 2006 20:20:19 +0000 (14:20 -0600)]
[PATCH] sata_nv: fix ATAPI in ADMA mode
The attached patch against 2.6.19-rc6-mm1 fixes some problems in sata_nv
with ATAPI devices on controllers running in ADMA mode. Some of the
logic in the nv_adma_bmdma_* functions was inverted causing a bunch of
warnings and caused those functions not to work properly. Also, when an
ATAPI device is connected, we need to use the legacy DMA engine. The
code now disables the PCI configuration register bits for ADMA so that
this works, and ensures that no ATAPI DMA commands go through until this
is done.
Alan [Mon, 27 Nov 2006 16:19:36 +0000 (16:19 +0000)]
[PATCH] pata_via suspend/resume support
The major VIA issues were handled by the quirks update for resume quirks.
The ATA driver also has to do some work however when resuming from RAM.
Certain chips need the FIFO reconfiguring, and the 66MHz clock setup
updating.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Wed, 22 Nov 2006 17:01:06 +0000 (17:01 +0000)]
[PATCH] pata_cs5520: resume support
The CS5520 doesn't need much help to resume but we do need to restore
pcicfg which may have been reset to the BIOS default which is
sometimes incorrect.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Wed, 22 Nov 2006 16:57:36 +0000 (16:57 +0000)]
[PATCH] PATA libata: suspend/resume simple cases
This patch adds the suspend/resume callbacks for drivers which don't need
any additional help (beyond the pci resume quirk patch I posted earlier
anyway). Also bring version numbers back inline with master copies.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Wed, 22 Nov 2006 17:28:41 +0000 (17:28 +0000)]
[PATCH] pata_sil680 suspend/resume
The SI680 can come back from s2ram with the clocks disabled (crash time)
or wrong (ugly as this can cause CRC errors, and in theory corruption).
On a resume we must put the clock back.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Wed, 22 Nov 2006 17:23:37 +0000 (17:23 +0000)]
[PATCH] pata_rz1000: Force readahead off on resume
The RZ1000 is a generic device except that it has a readahead fifo flaw
that corrupts. We force this off at init time but we want to be paranoid
and force it off at resume as well. I don't know of any actual hardware
that supports both RZ1000 and suspend to RAM but given its a disk muncher
better safe than sorry.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Wed, 22 Nov 2006 17:26:06 +0000 (17:26 +0000)]
[PATCH] pata_ali: suspend/resume support
Various chipset functions must be reprogrammed on a resume from RAM,
without this things like ATAPI DMA stop working on resume with some
chipset variants. Split the chipset programming and init time method selection into two functions.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This (and the pci resume quirk code) get the JMicron controllers to
resume properly. Without this patch the drive mapping changes when you
suspend/resume which is not good at all....
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan [Wed, 22 Nov 2006 17:21:03 +0000 (17:21 +0000)]
[PATCH] pata_cs5530: suspend/resume support
The 5530 needs various set up performing both at init time and resume
time. To keep the code clean the common setup code is moved into a new
function and called from both handlers.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch updates the sata_promise driver as follows:
- Correct typo in definition of PDC_TBG_MODE: it's at 0x41C not 0x41
in first-generation chips. This error caused PCI access alignment
exceptions on SPARC64, and on all platforms it disabled the expected
initialisation of TBG mode.
- Add flags field to struct pdc_host_priv. Define PDC_FLAG_GEN_II
and use it to distinguish first- and second-generation chips.
- Prevent the FLASH_CTL FIFO_SHD bit from being set to 1 on second-
generation chips. This matches Promises' ulsata2 driver.
- Prevent TBG mode and SLEW rate initialisation in second-generation chips.
These two registers have moved, TBG mode has been redefined, and
Promise's ulsata2 driver no longer attempts to initialise them.
- Correct PCI device table so devices 0x3570, 0x3571, and 0x3d73 are
marked as 2057x (2nd gen) not 2037x (1st gen).
- Correct PCI device table so device 0x3d17 is marked as 40518
(2nd gen 4 ports) not 20319 (1st gen 4 ports).
- Correct pdc_ata_init_one() to treat 20771 as a second-generation chip.
Tested on 0x3d75 (2nd gen), 0x3d73 (2nd gen), and 0x3373 (1st gen) chips.
The information comes from the newly uploaded Promise SATA HW specs,
Promise's ultra and ulsata2 drivers, and debugging on 3d75/3d73/3373 chips.
hp->hotplug_offset could now be removed and its value recomputed
in pdc_host_init() using hp->flags, but that would be a cleanup
not a functional change, so I'm ignoring it for now.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 14 Nov 2006 13:37:35 +0000 (22:37 +0900)]
[PATCH] libata: improve SCSI sense data generation
Update ata_gen_ata_sense() to use desc format sense data to report the
first failed block. The first failed block is read from result_tf
using ata_tf_read_block() which can handle all three address formats.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 14 Nov 2006 13:37:35 +0000 (22:37 +0900)]
[PATCH] libata: fix passthru sense data header
sb[7] should contain the length of whole information sense data
descriptor while desc[1] should contain the number of following bytes
in the descriptor. ie. 14 for sb[7] but 12 for desc[1].
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata didn't initialize result_tf.flags which indicates transfer type
(RW/FUA) and address type (CHS/LBA/LBA48). ata_gen_fixed_sense()
assumed result_tf.flags equals command tf.flags and failed to report
the first failed block to SCSI layer because zero tf flags indicates
CHS and bad block reporting for CHS is not implemented.
Implement fill_result_tf() which sets result_tf.flags to command
tf.flags and use it to fill result_tf.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Tue, 14 Nov 2006 13:36:12 +0000 (22:36 +0900)]
[PATCH] libata: improve failed qc reporting
Improve failed qc reporting. The original message didn't include the
actual command nor full error status and it was necessary to
temporarily patch the code to find out exactly which command is
causing problem. This patch makes EH report full command and result
TFs along with data direction and length. This change will make bug
reports more useful.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Fri, 10 Nov 2006 09:08:10 +0000 (18:08 +0900)]
[PATCH] ata_piix: apply device detection via polling IDENTIFY
PATA PIIX uses reset signature + TF r/w test for device presence
detection, which doesn't always work. It sometimes reports phantom
device which results in IDENTIFY timeouts.
SATA PIIX uses some combination of PCS + reset signature + TF r/w test
for device presence detection. No combination satifies all and for
some controllers, there doesn't seem to be any combination which
works reliably.
This patch makes both PATA and SATA piix's use reset signature + TF
r/w + polling IDENTIFY for device detection. This is what the old
libata (before irq-pio and new EH) did and what IDE does.
This patch also removes now obsolete PIIX_FLAG_IGNORE_PCS, force_pcs
and related code.
Tejun Heo [Fri, 10 Nov 2006 09:08:10 +0000 (18:08 +0900)]
[PATCH] libata: implement presence detection via polling IDENTIFY
On some controllers (ICHs in piix mode), there is *NO* reliable way to
determine device presence other than issuing IDENTIFY and see how the
transaction proceeds by watching the TF status register.
libata acted this way before irq-pio and phantom devices caused very
little problem but now that IDENTIFY is performed using IRQ drive PIO,
such phantom devices now result in multiple 30sec timeouts during
boot.
This patch implements ATA_FLAG_DETECT_POLLING. If a LLD sets this
flag, libata core issues the initial IDENTIFY in polling mode and if
the initial data transfer fails w/ HSM violation, the port is
considered to be empty thus replicating the old libata and IDE
behavior.
Tejun Heo [Fri, 10 Nov 2006 09:08:10 +0000 (18:08 +0900)]
[PATCH] libata: convert @post_reset to @flags in ata_dev_read_id()
Make ata_dev_read_id() take @flags instead of @post_reset. Currently
there is only one flag defined - ATA_READID_POSTRESET, which is
equivalent to @post_reset. This is preparation for polling presence
detection.
Tejun Heo [Sat, 11 Nov 2006 11:10:45 +0000 (20:10 +0900)]
[PATCH] libata: use FLUSH_EXT only when driver is larger than LBA28 limit
Many drives support LBA48 even when its capacity is smaller than
1<<28, as LBA48 is required for many functionalities. FLUSH_EXT is
mandatory for drives w/ LBA48 support.
Interestingly, at least one of such drives (ST960812A) has problems
dealing with FLUSH_EXT. It eventually completes the command but takes
around 7 seconds to finish in many cases thus drastically slowing down
IO transactions. This seems to be a firmware bug which sneaked into
production probably because no other ATA driver including linux IDE
issues FLUSH_EXT to drives which report support for LBA48 & FLUSH_EXT
but is smaller than 1<<28 blocks.
This patch adds ATA_DFLAG_FLUSH_EXT which is set iff the drive
supports LBA48 & FLUSH_EXT and is larger than LBA28 limit. Both cache
flush paths are updated to issue FLUSH_EXT only when the flag is set.
Note that the changed behavior is more inline with the rest of libata.
libata prefers shorter commands whenever possible.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Danny Kukawka <dkukawka@novell.com> Cc: Stefan Seyfried <seife@novell.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Thu, 9 Nov 2006 06:08:40 +0000 (15:08 +0900)]
[PATCH] ahci: honor PORTS_IMPL on ICH8s
Some ICH8s use non-linear port mapping. ahci driver didn't use to
honor PORTS_IMPL and this made ports after hole nonfunctional. This
patch makes ahci mark those ports as dummy and properly initialize all
the implemented ports after the dummies.
As it's unknown whether other AHCIs implement PORTS_IMPL register
properly, new board id board_ahci_pi is added and selectively applied
to ICH8s. All other AHCIs continue to use linear mapping regardless
of PORTS_IMPL value.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Robin H. Johnson <robbat2@gentoo.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Fri, 3 Nov 2006 13:18:06 +0000 (13:18 +0000)]
[PATCH] pdc202xx_old: Fix name clashes with PA-RISC
pdc_* functions are part of the global namespace for the PDC on PA-RISC
systems and this means our choice of pdc_ causes collisions between the
PDC globals and our static functions. Rename them to pdc202xx where they
are for both 2024x and 2026x.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Wed, 1 Nov 2006 09:39:27 +0000 (18:39 +0900)]
[PATCH] libata: implement ATA_EHI_SETMODE and ATA_EHI_POST_SETMODE
libata EH used to perform ata_set_mode() iff the EH session performed
reset as indicated by ATA_EHI_DID_RESET. This is incorrect because
->dev_config() called by revalidation is allowed to modify transfer
mode which ata_set_mode() should take care of. This patch implements
the following two flags.
* ATA_EHI_SETMODE: set during EH to schedule ata_set_mode(). Both new
device attachment and revalidation set this flag.
* ATA_EHI_POST_SETMODE: set while the device is revalidated after
ata_set_mode(). Post-setmode revalidation is different from initial
configuaration and EH revalidation in that ->dev_config() is not
allowed tune transfer mode. LLD can use this flag to determine
whether it's allowed to tune transfer mode. Note that POST_SETMODE
->dev_config() is guaranteed to be preceded by non-POST_SETMODE
->dev_config().
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Wed, 1 Nov 2006 09:38:52 +0000 (18:38 +0900)]
[PATCH] libata: implement ATA_EHI_PRINTINFO
Implement ehi flag ATA_EHI_PRINTINFO. This flag is set when device
configuration needs to print out device info. This used to be handled
by @print_info argument to ata_dev_configure() but LLDs also need to
know about it in ->dev_config() callback.
This patch replaces @print_info w/ ATA_EHI_PRINTINFO and make sata_sil
print workaround messages only on the initial configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Wed, 1 Nov 2006 09:00:24 +0000 (18:00 +0900)]
[PATCH] ahci: update ahci-vt8251 reset sequence
ahci-vt8251
* requires hardreset after PHY status change
* doesn't clear BSY on signature FIS after hardreset
* needs SError cleared for the port to operate after hardreset
This patch implements ahci_vt8251_hardreset() and sets
ATA_FLAG_HRST_TO_RESUME to handle the above behaviors. This fixes EH
including hotplug on vt8251.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH] libata: make user scan wait for scan to complete
Make user scan wait for scan to complete. This way user can wait for
warm plug request to complete and is prevented from causing EH event
storm by repetitively issuing scan request while EH is in progress.
Tejun Heo [Mon, 9 Oct 2006 02:10:26 +0000 (11:10 +0900)]
[PATCH] libata: move ata_irq_on() into libata-sff.c
ata_irq_on() isn't used outside of libata core layer. The function is
TF/SFF interface specific but currently used by core path with some
hack too. Move it from include/linux/libata.h to
drivers/ata/libata-sff.c.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tejun Heo [Mon, 9 Oct 2006 09:32:15 +0000 (18:32 +0900)]
[PATCH] libata: handle 0xff status properly
libata waits for !BSY even when the status register reports 0xff.
This causes long boot delays when D8 isn't pulled down properly. This
patch does the followings.
* don't wait if status register is 0xff in all wait functions
* make ata_busy_sleep() return 0 on success and -errno on failure.
-ENODEV is returned on 0xff status and -EBUSY on other failures.
* make ata_bus_softreset() succeed on 0xff status. 0xff status is not
reset failure. It indicates no device. This removes unnecessary
retries on such ports. Note that the code change assumes unoccupied
port reporting 0xff status does not produce valid device signature.
Signed-off-by: Tejun Heo <htejun@gmail.com> Cc: Joe Jin <lkmaillist@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Sat, 28 Oct 2006 02:08:46 +0000 (19:08 -0700)]
[PATCH] libata: Revamp blacklist support to allow multiple kinds of blacklisting flaws
Signed-off-by: Alan Cox <alan@redhat.com> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Robert Hancock [Sat, 28 Oct 2006 02:08:41 +0000 (19:08 -0700)]
[PATCH] sata_nv ADMA/NCQ support for nForce4
This patch adds support for ADMA mode on NVIDIA nForce4 (CK804/MCP04) SATA
controllers to the sata_nv driver. Benefits of ADMA mode include:
- NCQ support
- Reduced CPU overhead (controller DMAs command information from memory
instead of them being pushed in by the CPU)
- Full 64-bit DMA support
ADMA mode is enabled by default in this version. To disable it, set the
module parameter adma_enabled=0.
Signed-off-by: Robert Hancock <hancockr@shaw.ca> Cc: Jeff Garzik <jeff@garzik.org> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff Garzik [Sat, 21 Oct 2006 19:54:13 +0000 (15:54 -0400)]
[libata] pata_marvell: minor and trivial cleanups
- use pci_iomap() [Alan, version 0.0.5t]
- fix Alan's version 0.0.5t change
- line length, trailing whitespace, case indentation cleanups
- don't use deprecated ->eng_timeout() in a driver that uses new EH
This is a legacy mode PATA driver for the 6101/45 and will also drive
the SATA ports 1 & 2 in legacy mode as well if desired. Tested and
confirmed working by users. The chip supports AHCI type behaviour for
SATA and has a more advanced PATA interface as well so this driver will
get it working but not get best performance for now.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH] pci_module_init() conversion for pata_pdc2027x
pci_module_init() conversion for pata_pdc2027x
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Acked-by: Alan Cox <alan@redhat.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
[PATCH] pci_module_init convertion in ata_generic.c
pci_module_init convertion in ata_generic.c.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de> Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox [Fri, 29 Sep 2006 17:30:05 +0000 (18:30 +0100)]
[PATCH] libata: Winbond support
Winbond 83759A support in non-multichip mode (afaik nobody ever used
multichip mode anyway). The 83759 is not supported by this driver as it
is already handled elsewhere and doens't use the same interfaces.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Linus Torvalds [Sat, 2 Dec 2006 00:44:02 +0000 (16:44 -0800)]
Merge branch 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (31 commits)
[MIPS] Remove duplicate ISA DMA code for 0 DMA channel case.
[MIPS] Remove unused definition of cpu_to_lelongp()
[MIPS] Remove userspace proofing from <asm/bitops.h>.
[MIPS] Remove old junk left from old atomic_lock.
[MIPS] Use conditional traps for BUG_ON on MIPS II and better.
[MIPS] mips HPT cleanup: make clocksource_mips public
[MIPS] do_IRQ cleanup
[MIPS] Avoid dupliate D-cache flush on R400C / R4400 SC and MC variants.
[MIPS] Remove redundant r4k_blast_icache() calls
[MIPS] Work around bogus gcc warnings.
[MIPS] Fix double inclusions
[MIPS] use generic_handle_irq, handle_level_irq, handle_percpu_irq
[MIPS] IRQ cleanups
[MIPS] mips hpt cleanup: get rid of mips_hpt_init
[MIPS] PB1200: Remove duplicate definitions
[MIPS] Fix alignment hole in struct cache_desc; shrink struct.
[MIPS] Oprofile: kernel support for the R10000.
[MIPS] Remove unused R10000 performance counter definitions.
[MIPS] Add support for kexec
[MIPS] Don't print presence of WAIT instruction on bootup.
...
Linus Torvalds [Sat, 2 Dec 2006 00:43:42 +0000 (16:43 -0800)]
Merge branch 'for-2.6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6
* 'for-2.6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
SELinux: validate kernel object classes and permissions
SELinux: ensure keys constant in hashtab_search
SELinux: export object class and permission definitions
SELinux: remove current object class and permission validation mechanism
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (103 commits)
usbcore: remove unused argument in autosuspend
USB: keep count of unsuspended children
USB hub: simplify remote-wakeup handling
USB: struct usb_device: change flag to bitflag
OHCI: make autostop conditional on CONFIG_PM
USB: Add autosuspend support to the hub driver
EHCI: Fix root-hub and port suspend/resume problems
USB: create a new thread for every USB device found during the probe sequence
USB: add driver for the USB debug devices
USB: added dynamic major number for USB endpoints
USB: pegasus error path not resetting task's state
USB: endianness fix for asix.c
USB: build the appledisplay driver
USB serial: replace kmalloc+memset with kzalloc
USB: hid-core: canonical defines for Apple USB device IDs
USB: idmouse cleanup
USB: make drivers/usb/core/driver.c:usb_device_match() static
USB: lh7a40x_udc remove double declaration
USB: pxa2xx_udc recognizes ixp425 rev b0 chip
usbtouchscreen: add support for DMC TSC-10/25 devices
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
Driver core: show drivers in /sys/module/
Documentation/driver-model/platform.txt update/rewrite
Driver core: platform_driver_probe(), can save codespace
driver core: Use klist_remove() in device_move()
driver core: Introduce device_move(): move a device to a new parent.
Driver core: make drivers/base/core.c:setup_parent() static
driver core: Introduce device_find_child().
sysfs: sysfs_write_file() writes zero terminated data
cpu topology: consider sysfs_create_group return value
Driver core: Call platform_notify_remove later
ACPI: Change ACPI to use dev_archdata instead of firmware_data
Driver core: add dev_archdata to struct device
Driver core: convert sound core to use struct device
Driver core: change mem class_devices to be real devices
Driver core: convert fb code to use struct device
Driver core: convert firmware code to use struct device
Driver core: convert mmc code to use struct device
Driver core: convert ppdev code to use struct device
Driver core: convert PPP code to use struct device
Driver core: convert cpuid code to use struct device
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix timezone handling on stat to os/2
[CIFS] Incorrect hardlink count when original file is cached (oplocked)
Kay Sievers [Fri, 24 Nov 2006 11:15:25 +0000 (12:15 +0100)]
Driver core: show drivers in /sys/module/
Show the drivers, which belong to the module:
$ ls -l /sys/module/usbcore/drivers/
hub -> ../../../bus/usb/drivers/hub
usb -> ../../../bus/usb/drivers/usb
usbfs -> ../../../bus/usb/drivers/usbfs
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is almost a rewrite of the driver-model/platform.txt documentation;
the previous text was obsolete (for several years), evidently it never
got updated to match the change from being a PC "legacy_bus" to the more
widely used core bus for most embedded systems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 17 Nov 2006 07:28:47 +0000 (23:28 -0800)]
Driver core: platform_driver_probe(), can save codespace
This defines a new platform_driver_probe() method allowing the driver's
probe() method, and its support code+data, to safely live in __init
sections for typical system configurations.
Many system-on-chip processors could benefit from this API, to the tune
of recovering hundreds to thousands of bytes per driver. That's memory
which is currently wasted holding code which can never be called after
system startup, yet can not be removed. It can't be removed because of
the linkage requirement that pointers to init section code (like, ideally,
probe support) must not live in other sections (like driver method tables)
after those pointers would be invalid.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cornelia Huck [Mon, 20 Nov 2006 16:07:51 +0000 (17:07 +0100)]
driver core: Introduce device_move(): move a device to a new parent.
Provide a function device_move() to move a device to a new parent device. Add
auxilliary functions kobject_move() and sysfs_move_dir().
kobject_move() generates a new uevent of type KOBJ_MOVE, containing the
previous path (DEVPATH_OLD) in addition to the usual values. For this, a new
interface kobject_uevent_env() is created that allows to add further
environmental data to the uevent at the kobject layer.
Thomas Maier [Sun, 22 Oct 2006 17:17:47 +0000 (19:17 +0200)]
sysfs: sysfs_write_file() writes zero terminated data
since most of the files in sysfs are text files,
it would be nice, if the "store" function called
during sysfs_write_file() gets a zero terminated
string / data.
The current implementation seems not to ensure this.
(But only if it is the first time the zeroed buffer
page is allocated.)
So the buffer can be scanned by sscanf() easily,
for example.
This patch simply sets a \0 char behind the
data in buffer->page.
Signed-off-by: Thomas Maier <balagi@justmail.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Heiko Carstens [Thu, 9 Nov 2006 03:46:09 +0000 (19:46 -0800)]
cpu topology: consider sysfs_create_group return value
Take return value of sysfs_create_group() into account. That function got
called in case of CPU_ONLINE notification. Since callbacks are not allowed
to fail on CPU_ONLINE notification do the sysfs group creation on
CPU_UP_PREPARE notification.
Also remember if creation succeeded in a bitmask. So it's possible to know
whether it's legal to call sysfs_remove_group or not.
In addition some other minor stuff:
- since CPU_UP_PREPARE might fail add CPU_UP_CANCELED handling as well.
- use hotcpu_notifier instead of register_hotcpu_notifier.
- #ifdef code that isn't needed in the !CONFIG_HOTPLUG_CPU case.
Move the call to platform_notify_remove() to after the call to
bus_remove_device(), where it belongs. It's bogus to notify the platform
of removal while drivers are still attached to the device and possibly
still operating since the platform might use this callback to tear down
some resources used by the driver (ACPI bits, iommu table, ...)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: "Brown, Len" <len.brown@intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
projects / linux-2.6 / log