Francois Romieu [Mon, 27 Feb 2006 22:15:06 +0000 (23:15 +0100)]
8139cp: fix broken suspend/resume
- check that the device is up before it is enabled again;
- the descriptor ring indexes must be set to zero before
cp_init_hw() is issued. Add a nice comment to remember
that skb allocation failure is still not handled.
Francois Romieu [Mon, 27 Feb 2006 22:11:08 +0000 (23:11 +0100)]
via-velocity: fix memory corruption when changing the mtu
velocity_rx_refill() only replenishes the descriptor entries which
belong to the CPU. It works great in the Rx path but the driver must
ensure that all the descriptors are freed before velocity_rx_refill()
is used in velocity_change_mtu(). The patch resets the Rx descriptors
in velocity_free_rd_ring().
Ralf Baechle [Thu, 23 Feb 2006 12:23:27 +0000 (12:23 +0000)]
[MIPS] SMP: Fix initialization order bug.
A recent change requires cpu_possible_map to be initialized before
smp_sched_init() but most MIPS platforms were initializing their
processors in the prom_prepare_cpus callback of smp_prepare_cpus. The
simple fix of calling prom_prepare_cpus from one of the earlier SMP
initialization hooks doesn't work well either since IPIs may require
init_IRQ() to have completed, so bit the bullet and split
prom_prepare_cpus into two initialization functions, plat_smp_setup
which is called early from setup_arch and plat_prepare_cpus called where
prom_prepare_cpus used to be called.
Further investigation shows that the problem was introduced during
Alan's "TTY layer buffering revamp" patch, the amount of data to be
copied being reduced after buffer allocation. Moving the count fixup
around solves the problem.
James Bottomley [Sun, 26 Feb 2006 23:07:45 +0000 (17:07 -0600)]
[PATCH] fix voyager after topology.c move
Commit 9c869edac591977314323a4eaad5f7633fca684f broke voyager again
rather subtly because it already had its own topology exporting
functions, so now each CPU gets registered twice.
I think we can actually use the generic ones, so I don't propose
reverting it. The attached should eliminate the voyager topology
functions in favour of the generic ones.
I also added a define to ensure voyager is never hotplug CPU (we don't
have the support in the SMP harness).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Brian Magnuson [Mon, 27 Feb 2006 03:02:04 +0000 (04:02 +0100)]
[PATCH] fix build on x86_64 with !CONFIG_HOTPLUG_CPU
The commit e2c0388866dc12bef56b178b958f9b778fe6c687 added
setup_additional_cpus to setup.c but this is only defined if
CONFIG_HOTPLUG_CPU is set. This patch changes the #ifdef to reflect that.
Andi Kleen [Sun, 26 Feb 2006 03:18:52 +0000 (04:18 +0100)]
[PATCH] x86_64: Better ATI timer fix
The previous experiment for using apicmaintimer on ATI systems didn't
work out very well. In particular laptops with C2/C3 support often
don't let it tick during idle, which makes it useless. There were also
some other bugs that made the apicmaintimer often not used at all.
I tried some other experiments - running timer over RTC and some other
things but they didn't really work well neither.
I rechecked the specs now and it turns out this simple change is
actually enough to avoid the double ticks on the ATI systems. We just
turn off IRQ 0 in the 8254 and only route it directly using the IO-APIC.
I tested it on a few ATI systems and it worked there. In fact it worked
on all chipsets (NVidia, Intel, AMD, ATI) I tried it on.
According to the ACPI spec routing should always work through the
IO-APIC so I think it's the correct thing to do anyways (and most of the
old gunk in check_timer should be thrown away for x86-64).
But for 2.6.16 it's best to do a fairly minimal change:
- Use the known to be working everywhere-but-ATI IRQ0 both over 8254
and IO-APIC setup everywhere
- Except on ATI disable IRQ0 in the 8254
- Remove the code to select apicmaintimer on ATI chipsets
- Add some boot options to allow to override this (just paranoia)
In 2.6.17 I hope to switch the default over to this for everybody.
Andi Kleen [Sun, 26 Feb 2006 03:18:49 +0000 (04:18 +0100)]
[PATCH] x86_64: Move the SMP time selection earlier
SMP time selection originally ran after all CPUs were brought up because
it needed to know the number of CPUs to decide if it needs an MP safe
timer or not.
This is not needed anymore because we know present CPUs early.
This fixes a couple of problems:
- apicmaintimer didn't always work because it relied on state that was
set up time_init_gtod too late.
- The output for the used timer in early kernel log was misleading
because time_init_gtod could actually change it later. Now always
print the final timer choice
Andi Kleen [Sun, 26 Feb 2006 03:18:43 +0000 (04:18 +0100)]
[PATCH] x86_64: Disable ACPI blacklist by year for now on x86-64
ACPI is initialized very early on x86-64, before the DMI code is
initialized. This means it would often discover a 0 year and then turn
off ACPI because it thought the BIOS was too old. Some systems don't
boot without ACPI so this was a problem.
I have a full fix by adding new very early DMI detection, but it needs
more testing before it can be merged. For 2.6.16 let's just turn the
check off. It never made much sense anyways because there are no x86-64
systems older than 2002 or so and they generally all have working ACPI.
Andi Kleen [Sun, 26 Feb 2006 03:18:37 +0000 (04:18 +0100)]
[PATCH] x86-64/i386: Use common X86_PM_TIMER option and make it EMBEDDED
This makes x86-64 use the common X86_PM_TIMER Kconfig entry in drivers/acpi
And since PM timer is needed for correct timing on a lot of systems
now (e.g. AMD dual cores) and we often get bug reports from people
who forgot to set it make it depend on CONFIG_EMBEDDED. x86-64 had
this change before and it's a good thing.
I also fixed the description slightly to make this more clear.
Jon Mason [Sun, 26 Feb 2006 03:18:22 +0000 (04:18 +0100)]
[PATCH] x86_64: no_iommu removal in pci-gart.c
In previous versions of pci-gart.c, no_iommu was used to determine if IOMMU was
disabled in the GART DMA mapping functions. This changed in 2.6.16 and now
gart_xxx() functions are only called if gart is enabled. Therefore, uses of
no_iommu in the GART code are no longer necessary and can be removed.
Also, it removes double deceleration of no_iommu and force_iommu in pci.h and
proto.h, by removing the deceleration in pci.h.
Lastly, end_pfn off by one error.
Tested (along with patch 1/2) on dual opteron with gart enabled, iommu=soft,
and iommu=off.
Marc Zyngier [Sun, 26 Feb 2006 11:02:56 +0000 (12:02 +0100)]
[PATCH] Fix Specialix SI probing
As the (probably) last user of a Specialix SI board, I noticed that
recent kernels would fail to probe the sucker. Quick investigation
indicate a few missing braces...
I left the double probing in place, as it looks like it's been here
forever.
Signed-off-by: Marc Zyngier <maz@misterjones.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Al Viro [Sun, 26 Feb 2006 14:34:10 +0000 (08:34 -0600)]
[PATCH] sd: fix memory corruption with broken mode page headers
There's a problem in sd where we blindly believe the length of the
headers and block descriptors. Some devices return insane values for
these and cause our length to end up greater than the actual buffer
size, so check to make sure.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Also removed the buffer size magic number (512) and added DPOFUA of
zero to the defaults
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Daniele Venzano [Sat, 25 Feb 2006 22:01:09 +0000 (17:01 -0500)]
Fix Wake on LAN support in sis900
Fix two bugs in the WoL implementation of sis900. The first causes
hangs on some system on driver load, the second causes troubles
when disabling WoL support. Both fixes are one liner and really
simple.
Tejun Heo [Sat, 25 Feb 2006 04:52:30 +0000 (13:52 +0900)]
[PATCH] sata_sil: implement R_ERR on DMA activate FIS errata fix
Silicon Image has disclosed a new sil3114/3152 errata and workaround
which causes the controller to return R_ERR on DMA activate FIS if the
FIS is received while the next PRD is being fetched. This patch
implements the workaround.
This errata results in lock up and doesn't trigger if m15w workaround
is in effect. We stopped applying m15w to 3512 and 3114 in 2.6.14-rc1
which makes 3512/3114 lock up with some drives on all kernel versions
since 2.6.14-rc1 upto now (2.6.16-rc4). This patch should fix the
regression.
Signed-off-by: Tejun Heo <htejun@gmail.com> Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kumar Gala [Fri, 24 Feb 2006 16:54:52 +0000 (10:54 -0600)]
[PATCH] powerpc: Fix mem= cmdline handling on arch/powerpc for !MULTIPLATFORM
mem= command line option was being ignored in arch/powerpc if we were not
a CONFIG_MULTIPLATFORM (which is handled via prom_init stub). The initial
command line extraction and parsing needed to be moved earlier in the boot
process and have code to actual parse mem= and do something about it.
Zachary Amsden [Fri, 24 Feb 2006 21:04:27 +0000 (13:04 -0800)]
[PATCH] Fix topology.c location
When compiling a non-default subarch, topology.c is missing from the kernel
build. This causes builds with CONFIG_HOTPLUG_CPU to fail. In addition,
on Intel processors with cpuid level > 4, it causes intel_cacheinfo.c to
reference uninitialized data that should have been set up by the initcall
in topology.c which calls register_cpu. This causes a kernel panic on boot
on newer Intel processors. Moving topology.c to arch/i386/kernel fixes
both of these problems.
Thanks to Dan Hecht for finding and fixing this problem.
Signed-off-by: Zachary Amsden <zach@vmware.com> Signed-off-by: Dan Hecht <dhect@vmware.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- PF_SWAPWRITE needs to be set for RECLAIM_SWAP to be able to write
out pages to swap. Currently RECLAIM_SWAP may not do that.
- remove setting nr_reclaimed pages after slab reclaim since the slab shrinking
code does not use that and the nr_reclaimed pages is just right for the
intended follow up action.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ulrich Drepper [Fri, 24 Feb 2006 21:04:21 +0000 (13:04 -0800)]
[PATCH] flags parameter for linkat
I'm currently at the POSIX meeting and one thing covered was the
incompatibility of Linux's link() with the POSIX definition. The name.
Linux does not follow symlinks, POSIX requires it does.
Even if somebody thinks this is a good default behavior we cannot change this
because it would break the ABI. But the fact remains that some application
might want this behavior.
We have one chance to help implementing this without breaking the behavior.
For this we could use the new linkat interface which would need a new
flags parameter. If the new parameter is AT_SYMLINK_FOLLOW the new
behavior could be invoked.
I do not want to introduce such a patch now. But we could add the
parameter now, just don't use it. The patch below would do this. Can we
get this late patch applied before the release more or less fixes the
syscall API?
[PATCH] au1100fb: replaced io_remap_page_range() with io_remap_pfn_range()
Replaced the no longer existing io_remap_page_range() routine with the
io_remap_pfn_range() routine. Did not have a chance yet to test the
functionality of the driver, but at least the kernel compiles cleanly again.
Martin Michlmayr [Fri, 24 Feb 2006 21:04:16 +0000 (13:04 -0800)]
[PATCH] gbefb: Set default of FB_GBE_MEM to 4 MB
Allocating more than 4 MB memory for the GBE (SGI O2) framebuffer completely
breakfs gbefb support at the moment. According to comments on #mipslinux,
more than 4 MB has never worked correctly in Linux. Therefore, the default
should be 4 MB.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Antonino Daplas <adaplas@pol.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kaj-Michael Lang [Fri, 24 Feb 2006 21:04:15 +0000 (13:04 -0800)]
[PATCH] gbefb: IP32 gbefb depth change fix
The gbefb driver does not update the framebuffer layers visual setting when
depth is changed with fbset, resulting in strange colors (very dark blue in
16-bit, almost black in 24-bit).
Signed-off-by: Kaj-Michael Lang <milang@tal.org> Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Signed-off-by: Antonino Daplas <adaplas@pol.net> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
James Bottomley [Fri, 24 Feb 2006 21:04:14 +0000 (13:04 -0800)]
[PATCH] x86: fix broken SMP boot sequence
Recent GDT changes broke the SMP boot sequence if the booting CPU is
numbered anything other than zero. There's also a subtle source of error
in that the boot time CPU now uses cpu_gdt_table (which is actually the GDT
for booting CPUs in head.S). This patch fixes both problems by making GDT
descriptors themselves allocated from a per_cpu area and switching to them
in cpu_init(), which now means that cpu_gdt_table is exclusively used for
booting CPUs again.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Cc: Zachary Amsden <zach@vmware.com> Cc: Matt Tolentino <metolent@snoqualmie.dp.intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] page migration: Fix MPOL_INTERLEAVE behavior for migration via mbind()
migrate_pages_to() allocates a list of new pages on the intended target
node or with the intended policy and then uses the list of new pages as
targets for the migration of a list of pages out of place.
When the pages are allocated it is not clear which of the out of place
pages will be moved to the new pages. So we cannot specify an address as
needed by alloc_page_vma(). This causes problem for MPOL_INTERLEAVE which
will currently allocate the pages on the first node of the set. If mbind
is used with vma that has the policy of MPOL_INTERLEAVE then the
interleaving of pages may be destroyed.
This patch fixes that by generating a fake address for each alloc_page_vma
which will result is a distribution of pages as prescribed by
MPOL_INTERLEAVE.
Lee also noted that the sequence of nodes for the new pages seems to be
inverted. So we also invert the way the lists of pages for migration are
build.
Signed-off-by: Christoph Lameter <clameter@sgi.com> Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com> Looks-ok-to: Andi Kleen <ak@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
James Bottomley [Fri, 24 Feb 2006 21:04:11 +0000 (13:04 -0800)]
[PATCH] voyager: fix the cpu_possible_map to make voyager boot again
Right at the moment (thanks to a patch from Andrew), cpu_possible_map on
voyager is CPU_MASK_NONE, which means the machine always thinks it has no
CPUs. Fix that by doing an early initialisation of the cpu_possible_map
from the cpu_phys_present_map.
(akpm: we aim to please)
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Simon Vogl [Fri, 24 Feb 2006 21:04:09 +0000 (13:04 -0800)]
[PATCH] cfi: init wait queue in chip struct
Fix a kernel oops for Intel P30 flashes, where the wait queue head was not
initialized for the flchip struct, which in turn caused a crash at the
first read operation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@kernel.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] Kprobes causes NX protection fault on i686 SMP
Fix a problem seen on i686 machine with NX support where the instruction
could not be single stepped because of NX bit set on the memory pages
allocated by kprobes module. This patch provides allocation of instruction
solt so that the processor can execute the instruction from that location
similar to x86_64 architecture. Thanks to Bibo and Masami for testing this
patch.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Samuel Thibault [Fri, 24 Feb 2006 21:03:59 +0000 (13:03 -0800)]
[PATCH] vgacon: no vertical resizing on EGA
EGA boards suck: they mostly have write-only registers. This is
particularly problematic for the overflow register: for being able to write
to it, we would have to handle vertical sync & such too, which (I'd say)
would potentially break a lot of configurations. Instead, just disabling
vertical resize for EGA boards is just nice enough (horizontal resize still
works).
Improve (especially for coherence) some prototypes, and return code of
init_cow_file in error case - for a short write return -EINVAL, otherwise
return the error we got!
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: better error reporting for read_output
Do precise error handling: print precise error messages, distinguishing short
reads and read errors. This functions fails frequently enough for me so I
bothered doing this fix.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix an fd leak and a return of -1 instead of -errno in the error path - this
showed up in intensive testing of HPPFS, the os_connect_socket user.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use __attribute_used__ instead of __attribute__ ((unused)). This will help
with GCC > 3.2.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] uml: fix usage of kernel_errno in place of errno
To avoid conflicts, in kernel files errno is expanded to kernel_errno, to
distinguish it from glibc errno. In this case, the code wants to use the libc
errno but the kernel one is used; in the other usage, we return errno in place
of -errno in case of an error.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Improve some error messages in the COW driver, and say V3, not V2, when
talking about V3 format. Also resync with our userspace code utility a bit
more.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Acked-by: Jeff Dike <jdike@addtoit.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hirokazu Takata [Fri, 24 Feb 2006 21:03:51 +0000 (13:03 -0800)]
[PATCH] m32r: fix and update for gcc-4.0
Fix and update for gcc-4.0.
- arch/m32r/kernel/signal.c:
Change type of the 8th parameter of sys_rt_sigsuspend() from
'struct pt_regs' to 'struct pt_regs *'.
This functions make use of the 'regs' parameter to return status value,
but gcc-4.0 optimizes and removes it as a dead code.
Functions, sys_sigaltstack() and sys_rt_sigreturn(), have also modified.
- arch/m32r/lib/usercopy.c, include/asm-m32r/uaccess.h:
Add early-clobber constraints('&') to output values of asm statements;
these constraints seems to be required for gcc-4.0 register assignment.
Hirokazu Takata [Fri, 24 Feb 2006 21:03:50 +0000 (13:03 -0800)]
[PATCH] m32r: enable asm code optimization
Add -O2 option to AFLAGS to enable asm code optimization for m32r.
On m32r gas, "-m32r2 -O" option enables assembler's parallel code
generation optimization for M32R2 ISA as a default. So, "-no-parallel"
option is required explicitly for a cpu core with single instuction
issuing, for example, VDEC2.
Andrew Victor [Fri, 24 Feb 2006 22:27:50 +0000 (22:27 +0000)]
[ARM] 3348/1: Disable GPIO interrupts
Patch from Andrew Victor
disable_irq() lazily disables the interrupt, so the IRQ is only disabled
once the interrupt occurs again. The GPIO interrupt handler therefore
must first check disable_depth to see if the IRQ needs to be disabled.
Orignal patch by Bill Gatliff.
Signed-off-by: Andrew Victor <andrew@sanpeople.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Hugo Santos [Fri, 24 Feb 2006 21:16:25 +0000 (13:16 -0800)]
[IPV6] ip6_tunnel: release cached dst on change of tunnel params
The included patch fixes ip6_tunnel to release the cached dst entry
when the tunnel parameters (such as tunnel endpoints) are changed so
they are used immediatly for the next encapsulated packets.
Signed-off-by: Hugo Santos <hsantos@av.it.pt> Acked-by: Ville Nuorvala <vnuorval@tcs.hut.fi> Signed-off-by: David S. Miller <davem@davemloft.net>
NTFS: - Cope with attribute list attribute having invalid flags.
Windows copes with this and even chkdsk does not detect or fix this
so we have to cope with it, too. Thanks to Pawel Kot for reporting
the problem.
- Miscellaneous updates to layout.h.
Signed-off-by: Anton Altaparmakov <aia21@cantab.net>
Michal Ostrowski [Sat, 18 Feb 2006 14:29:59 +0000 (09:29 -0500)]
[PATCH] Fix race condition in hvc console.
tty_schedule_flip() would schedule a thread that would call flush_to_ldisc().
If tty_buffer_request_room() gets called prior to that thread running --
which is likely in this loop in hvc_poll(), it would set the active flag
in the tty buffer and consequently flush_to_ldisc() would ignore it.
The result is that input on the hvc console is not processed.
This fix calls tty_flip_buffer_push (and flags the tty as
"low_latency"). The push to the ldisc thus happens synchronously.
Signed-off-by: Michal Ostrowski <mostrows@watson.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Do disable, not enable, the HT APIC IRQ in the function that is
supposed to.
Enable the MPIC IRQ before enabling the downstream APIC IRQ, avoids
potentially losing an interrupt.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
Anton Blanchard [Mon, 13 Feb 2006 03:48:35 +0000 (14:48 +1100)]
[PATCH] powerpc: Fix runlatch performance issues
The runlatch SPR can take a lot of time to write. My original runlatch
code would set it on every exception entry even though most of the time
this was not required. It would also continually set it in the idle
loop, which is an issue on an SMT capable processor.
Now we cache the runlatch value in a threadinfo bit, and only check for
it in decrementer and hardware interrupt exceptions as well as the idle
loop. Boot on POWER3, POWER5 and iseries, and compile tested on pmac32.
Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
R Sharada [Wed, 22 Feb 2006 16:13:08 +0000 (21:43 +0530)]
[PATCH] powerpc64: fix spinlock recursion in native_hpte_clear
native_hpte_clear has a spinlock recursion problem with the native_tlbie_lock
being called twice, once in native_hpte_clear() and once within tlbie().
Fix the problem by changing the call to tlbie() in native_hpte_clear() to
__tlbie(). It still supports only 4k pages for now.
Signed-off-by: R Sharada <sharada@in.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Kumar Gala [Wed, 22 Feb 2006 15:46:02 +0000 (09:46 -0600)]
[PATCH] powerpc: Enable coherency for all pages on 83xx to fix PCI data corruption
On the 83xx platform to ensure the PCI inbound memory is handled properly we
have to turn on coherency for all pages in the MMU. Otherwise we see
corruption if inbound "prefetching/streaming" is enabled on the PCI controller.
Signed-off-by: Randy Vinson <rvinson@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Paul Mackerras <paulus@samba.org>
altivec_unavailable_exception is called without setting r3... it looks like
the r3 that actually gets passed in as struct pt_regs *regs is the
undisturbed value of r3 at the time the altivec instruction was encountered.
The user actually gets to choose the pt_regs printed in the Oops!
This fixes the oops by passing the correct pt_regs pointer to
altivec_unavailable_exception.
Signed-off-by: Alan Curry <pacman@TheWorld.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Haren Myneni [Tue, 7 Feb 2006 23:47:03 +0000 (15:47 -0800)]
[PATCH] powerpc: Trivial fix to set the proper timeout value for kdump
The panic CPU is waiting forever due to some large timeout value if some
CPU is not responding to an IPI.
This patch fixes the problem - the maximum waiting period will be
10 seconds and then the kdump boot will go ahead.
Signed-off-by: Haren Myneni <haren@us.ibm.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Michael Ellerman [Tue, 21 Feb 2006 06:22:55 +0000 (17:22 +1100)]
[PATCH] powerpc: Only calculate htab_size in one place for kexec
For kexec we need to know the size of the MMU hash table.
Currently we calculate the size once in the htab code, and then twice more in
the kexec code, once using htab_hash_mask and once using ppc64_pft_size.
On some machines the ppc64_pft_size calculation is broken because
ppc64_pft_size is not set.
So we need to fix the second calculation, but better still we should just
calculate the size once and use it everywhere else.
Tested on Power5 LPAR, Power4 non-LPAR and Power3.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
Richard Lucassen [Fri, 24 Feb 2006 00:23:51 +0000 (16:23 -0800)]
[NET]: Increase default IFB device count.
The most usable number of ifb devices is 2. Change the default to 2.
Signed-off-by: Richard Lucassen <spamtrap@lucassen.org> Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Signed-off-by: David S. Miller <davem@davemloft.net>
Jamal Hadi Salim [Fri, 24 Feb 2006 00:18:01 +0000 (16:18 -0800)]
[NET] ethernet: Fix first packet goes out with MAC 00:00:00:00:00:00
When you turn off ARP on a netdevice then the first packet always goes
out with a dstMAC of all zeroes. This is because the first packet is
used to resolve ARP entries. Even though the ARP entry may be resolved
(I tried by setting a static ARP entry for a host i was pinging from),
it gets overwritten by virtue of having the netdevice disabling ARP.
Subsequent packets go out fine with correct dstMAC address (which may
be why people have ignored reporting this issue).
To cut the story short:
the culprit code is in net/ethernet/eth.c::eth_header()
----
/*
* Anyway, the loopback-device should never use this
function...
*/
Note how the h_dest is being reset when device has IFF_NOARP.
As a note:
All devices including loopback pass a daddr. loopback in fact passes
a 0 all the time ;->
This means i can delete the check totaly or i can remove the IFF_NOARP
Alexey says:
--------------------
I think, it was me who did this crap. It was so long ago I do not remember
why it was made.
I remember some troubles with dummy device. It tried to resolve
addresses, apparently, without success and generated errors instead of
blackholing. I think the problem was eventually solved at neighbour
level.
After some thinking I suspect the deletion of this chunk could change
behaviour of some parts which do not use neighbour cache f.e. packet
socket.
I think safer approach would be to move this chunk after if (daddr).
And the possibility to remove this completely could be analyzed later.
--------------------
Patch updated with Alexey's safer suggestions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca> Acked-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Wed, 22 Feb 2006 22:47:13 +0000 (14:47 -0800)]
[XFRM]: Eliminate refcounting confusion by creating __xfrm_state_put().
We often just do an atomic_dec(&x->refcnt) on an xfrm_state object
because we know there is more than 1 reference remaining and thus
we can elide the heavier xfrm_state_put() call.
Do this behind an inline function called __xfrm_state_put() so that is
more obvious and also to allow us to more cleanly add refcount
debugging later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
[IPV4]: Fix garbage collection of multipath route entries
When garbage collecting route cache entries of multipath routes
in rt_garbage_collect(), entries were deleted from the hash bucket
'i' while holding a spin lock on bucket 'k' resulting in a system
hang. Delete entries, if any, from bucket 'k' instead.
Signed-off-by: Suresh Bhogavilli <sbhogavilli@verisign.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 21 Feb 2006 21:37:35 +0000 (13:37 -0800)]
[NETFILTER]: Fix bridge netfilter related in xfrm_lookup
The bridge-netfilter code attaches a fake dst_entry with dst->ops == NULL
to purely bridged packets. When these packets are SNATed and a policy
lookup is done, xfrm_lookup crashes because it tries to dereference
dst->ops.
Change xfrm_lookup not to dereference dst->ops before checking for the
DST_NOXFRM flag and set this flag in the fake dst_entry.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log