Alan Stern [Tue, 3 Jan 2006 15:30:31 +0000 (10:30 -0500)]
[PATCH] USB: gadgetfs: set "zero" flag for short control-IN response
This patch (as622) makes gadgetfs set the "zero" flag for control-IN
responses, when the length of the response is shorter than the length of
the request.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Olav Kongas [Tue, 27 Dec 2005 14:04:02 +0000 (16:04 +0200)]
[PATCH] USB: isp116x-hcd: replace mdelay() by msleep()
Replace mdelay() by msleep() in bus_suspend(); the rest of the system will
gain 7ms. The related code is reorganized to minimize the number of
locking/unlocking calls.
The last hunk of the patch is the formatting change by Lindent.
Signed-off-by: Olav Kongas <ok@artecdesign.ee> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Mon, 23 Jan 2006 22:17:21 +0000 (17:17 -0500)]
[PATCH] USB: UHCI: No FSBR until device is configured
Some USB devices don't enumerate well with FSBR turned on. This patch
keeps devices on the low-speed part of the schedule (which doesn't use
FSBR) until they have been fully configured.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vojtech Pavlik [Thu, 26 Jan 2006 06:44:31 +0000 (07:44 +0100)]
[PATCH] USB HID: add blacklist entry for HP keyboard
My earlier experiment (adding a clear-halt for the interrupt-in
endpoint) failed. It turns out that it does cause problems for other
devices. And it wasn't needed anyway; a simple blacklist entry was
enough to get my HP keyboard working.
This patch (as643) removes the clear-halt call and adds the blacklist
entry.
matthieu castet [Wed, 18 Jan 2006 06:39:27 +0000 (07:39 +0100)]
[PATCH] UEAGLE : cmv name bug (was cosmetic)
this patch correct a possible bug with cmv_name being static. If there
is 2 modems and the driver is scheduled when filling cmv_name this could
result with garbage in cmv_name. We allocate cmv_name on the stack but
with a small size in order to avoid that.
matthieu castet [Wed, 18 Jan 2006 06:38:19 +0000 (07:38 +0100)]
[PATCH] UEAGLE : add iso support
This patch adds the support for isochronous pipe.
A new module parameter is added to select iso mode. It is set to iso by
default because bulk mode doesn't work well at high speed rate (>3 Mbps
for upload).
We use UDSL_IGNORE_EILSEQ flags because ADI firmware doesn't reply to
ISO IN when it has nothing to send [1].
[1]
from cypress datasheet :
The ISOSEND0 Bit (bit 7 in the USBPAIR Register) is used when the EZ-USB
FX chip receives an isochronous IN token while the IN FIFO is empty. If
ISOSEND0=0 (the default value), the USB core does not respond to the IN
token. If ISOSEND0=1, the USB core sends a zero-length data packet in
response to the IN token. The action to take depends on the overall
system design. The ISOSEND0 Bit applies to all of the isochronous IN
endpoints, IN-8 through IN-15.
Arjan van de Ven [Fri, 13 Jan 2006 14:52:55 +0000 (15:52 +0100)]
[PATCH] USBATM: semaphore to mutex conversion
This is the usbatm part of the Arjan, Jes and Ingo
mass semaphore to mutex conversion, reworked to apply on top
of the patches I just sent to you. This time, with correct
attribution and signed-off lines.
Signed-off-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Duncan Sands <baldrick@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Duncan Sands [Fri, 13 Jan 2006 10:12:58 +0000 (11:12 +0100)]
[PATCH] USBATM: -EILSEQ workaround
Don't throttle on -EILSEQ urb status if requested by a minidriver.
It seems the ueagle modems are buggy, giving -EILSEQ when they
have no data to send. The ueagle change will be sent separately
by the ueagle guys. Patch by Matthieu Castet.
Duncan Sands [Fri, 13 Jan 2006 10:06:46 +0000 (11:06 +0100)]
[PATCH] USBATM: handle urbs containing partial cells
The receive logic has always assumed that urbs contain an integral
number of ATM cells, which is a bit naughty, though it never caused
any problems with bulk transfers. Isochronous urbs spank us soundly
for this. Fixed thanks to this patch, mostly by Stanislaw Gruszka.
Duncan Sands [Fri, 13 Jan 2006 09:59:23 +0000 (10:59 +0100)]
[PATCH] USBATM: allow isochronous transfer
While the usbatm core has had some support for using isoc urbs
for some time, there was no way for users to turn it on. While
use of isoc transfer should still be considered experimental, it
now works well enough to let users turn it on. Minidrivers signal
to the core that they want to use isoc transfer by setting the new
UDSL_USE_ISOC flag. The speedtch minidriver gets a new module
parameter enable_isoc (defaults to false), plus some logic that
checks for the existence of an isoc receive endpoint (not all
speedtouch modems have one).
Duncan Sands [Fri, 13 Jan 2006 09:52:38 +0000 (10:52 +0100)]
[PATCH] USBATM: measure buffer size in bytes; force valid sizes
Change the module parameters rcv_buf_size and snd_buf_size to
specify buffer sizes in bytes rather than ATM cells. Since
there is some danger that users may not notice this change,
the parameters are renamed to rcv_buf_bytes etc. The transmit
buffer needs to be a multiple of the ATM cell size in length,
while the receive buffer should be a multiple of the endpoint
maxpacket size (this wasn't enforced before, which causes trouble
with isochronous transfers), so enforce these restrictions. Now
that the usbatm probe method inspects the endpoint maxpacket size,
minidriver bind routines need to set the correct alternate setting
for the interface in their bind routine. This is the reason for
the speedtch changes.
Duncan Sands [Fri, 13 Jan 2006 09:13:19 +0000 (10:13 +0100)]
[PATCH] USBATM: use dev_kfree_skb_any rather than dev_kfree_skb
In one spot (usbatm_cancel_send) we were calling dev_kfree_skb with irqs
disabled. This mistake is just too easy to make, so systematically use
dev_kfree_skb_any rather than dev_kfree_skb.
Duncan Sands [Fri, 13 Jan 2006 09:05:15 +0000 (10:05 +0100)]
[PATCH] USBATM: shutdown open connections when disconnected
This patch causes vcc_release_async to be applied to any open
vcc's when the modem is disconnected. This signals a socket
shutdown, letting the socket user know that the game is up.
I wrote this patch because of reports that pppd would keep
connections open forever when the modem is disconnected.
This patch does not fix that problem, but it's a step in the
right direction. It doesn't help because the pppoatm module
doesn't yet monitor state changes on the ATM socket, so simply
never realises that the ATM connection has gone down (meaning
it doesn't tell the ppp layer). But at least there is a socket
state change now. Unfortunately this patch may create problems
for those rare users like me who use routed IP or some other
non-ppp connection method that goes via the ATM ARP daemon: the
daemon is buggy, and with this patch will crash when the modem
is disconnected. Users with a buggy atmarpd can simply restart
it after disconnecting the modem.
Duncan Sands [Fri, 13 Jan 2006 08:48:36 +0000 (09:48 +0100)]
[PATCH] USBATM: xusbatm rewrite
The xusbatm driver is for otherwise unsupported modems.
All it does is grab hold of a user-specified set of
interfaces - the generic usbatm core methods (hopefully)
do the rest. As Aurelio Arroyo discovered when he tried
to use xusbatm (big mistake!), the interface grabbing logic
was completely borked. Here is a rewrite that works.
Duncan Sands [Tue, 17 Jan 2006 10:16:13 +0000 (11:16 +0100)]
[PATCH] USBATM: add flags field
Have minidrivers and the core signal special requirements
using a flags field in struct usbatm_data. For the moment
this is only used to replace the need_heavy_init bind
parameter, but there'll be new flags in later patches.
Luca Risolia [Fri, 13 Jan 2006 17:19:43 +0000 (17:19 +0000)]
[PATCH] USB: SN9C10x driver updates
SN9C10x driver updates:
- Use kzalloc() instead of kmalloc()
- Move some macro definitions from sn9c102.h to sn9c102_core.c
- Use vfree() and vmalloc_32() instead of rvfree() and rvmalloc()
- Fix mmap() sys call
- Documentation updates
This patch corrects the URB initialisation for transfers
like this is done in other drivers too.
Without this patch no data was transmitted on a PXA270 OHCI
platform. May apply to others too.
Luca Risolia [Thu, 5 Jan 2006 18:14:04 +0000 (18:14 +0000)]
[PATCH] USB: SN9C10x driver updates and bugfixes
SN9C10x driver updates and bugfixes.
Changes: + new, - removed, * cleanup, @ bugfix:
@ fix poll()
@ Remove bad get_ctrl()'s
* Reduce ioctl stack usage
* Remove final ";" from some macro definitions
* Better support for SN9C103
+ Add sn9c102_write_regs()
+ Add 0x0c45/0x602d to the list of SN9C10x based devices
+ Add support for OV7630 image sensors
+ Provide support for the built-in microphone interface of the SN9C103
+ Documentation updates
+ Add 0x0c45/0x602e to the list of SN9C10x based devices
Matthew Dharm [Sat, 31 Dec 2005 03:06:53 +0000 (19:06 -0800)]
[PATCH] USB: usb-storage: Add support for Rio Karma
This patch from Bob Copeland adds support for the Rio Karma portable
digital audio player to the usb-storage driver. The only thing needed to
support this device is a one-time (per plugin) init command which is sent
to the device.
Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
So it picked up my UPS, and loaded the driver.
Whilst no harm came, because it later checks the vendor/product IDs,
this driver should probably be rewritten to only probe
for the device IDs it actually knows about.
Rui Santos [Mon, 9 Jan 2006 13:12:40 +0000 (13:12 +0000)]
[PATCH] USB: ftdi: Two new ATIK based USB astronomical CCD cameras
Documentation: Specify grayscale specification on ATIK-ATK16
and ATIK-ATK16HR comments.
New: Add ProductID and VendorID for devices ATIK-ATK16C and
ATIK-ATK16HRC. These devices are also USB Astronomical CCD
cameras that work through an FTDI 245BM chip, share the
same base hardware but, it has a colour CCD chip instead
of a grayscale one.
Wouter Paesen [Tue, 3 Jan 2006 13:30:31 +0000 (14:30 +0100)]
[PATCH] USB: ftdi_sio: new PID for PCDJ DAC2
The attached patch adds a new PID for the ftdi_sio driver. It will
enable support for PC-DJ's DAC-2 controller module
(more information on http://www.pcdjhardware.com/DAC2.asp)
Ian Abbott [Mon, 9 Jan 2006 17:11:40 +0000 (17:11 +0000)]
[PATCH] USB: ftdi_sio: new IDs for Westrex devices
This patch adds two new devices to the ftdi_sio driver's device ID
table. The device IDs were supplied by Cory Lee to support two POS
printers made by Westrex International (Model 777 and Model 8900F).
Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch includes the Vendor Id for a optic fiber to USB device named
TTUSB from thought Technology. It's just add the vendor Id to
ftdi_sio.h and add the Vendor ID and model Id to table_combined.
Signed-off-by: Louis Nyffenegger <louis.nyffenegger@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Thu, 5 Jan 2006 08:26:30 +0000 (00:26 -0800)]
[PATCH] USB: ub 05 Bulk reset
For crying out loud, they have devices which do not like port resets.
So, do what usb-storage does and try both bulk and port resets.
We start with a port reset (which usb-storage does at the end of transport),
then do a Bulk reset, then a port reset again. This seems to work for me.
The code is getting dirtier and dirtier here, but I swear that I'll
do something about it (see those two new XXX). Honest.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Thu, 5 Jan 2006 08:14:02 +0000 (00:14 -0800)]
[PATCH] USB: ub 04 Loss of timer and a hang
If SCSI commands are submitted while other commands are still processed,
the dispatch loop turns, and we stop the work_timer. Then, if URB fails
to complete, ub hangs until the device is unplugged.
This does not happen often, becase we only allow one SCSI command per
block device, but does happen (on multi-LUN devices, for example).
The fix is to stop timer only when we actually going to change the state.
The nicest code would be to have the timer stopped in URB callback, but
this is impossible, because it can be called from inside a timer, through
the urb_unlink. Then we get BUG in timer.c:cascade(). So, we do it a
little dirtier.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Wed, 28 Dec 2005 22:22:17 +0000 (14:22 -0800)]
[PATCH] USB: ub 03 Oops with CFQ
The blk_cleanup_queue does not necesserily destroy the queue. When we
destroy the corresponding ub_dev, it may leave the queue spinlock pointer
dangling.
This patch moves spinlocks from ub_dev to static memory. The locking
scheme is not changed. These spinlocks are still separate from the ub_lock.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Tue, 24 Jan 2006 15:15:30 +0000 (07:15 -0800)]
[PATCH] USB: fix EHCI early handoff issues
This moves the previously widely-used ehci-pci.c BIOS handoff
code into the pci-quirks.c file, replacing the less widely used
"early handoff" version that seems to cause problems lately.
One notable change: the "early handoff" version always enabled
an SMI IRQ ... and did so even if the pre-Linux code said it was
not using EHCI (and not expecting EHCI SMIs). Looks like a goof
in a workaround for some unknown BIOS version.
This merged version only forcibly enables those IRQs when pre-Linux
code says it's using EHCI. And now it always forces them off "just
in case".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds [Tue, 31 Jan 2006 21:11:41 +0000 (13:11 -0800)]
Fix ipv4/igmp.c compile with gcc-4 and IP_MULTICAST
Modern versions of gcc do not like case statements at the end of a block
statement: you need at least an empty statement. Using just a "break;"
is preferred for visual style.
Moore, Eric [Wed, 18 Jan 2006 00:06:23 +0000 (17:06 -0700)]
[SCSI] fusion: unloading the driver results in panic - fix
The ioc->alt_ioc->alt_ioc pointer is not getting cleared
during driver unload time. This dangling pointer
can result in panic in certain circumstances, such
as error recovery, or firmware download in flashless
environments. This only impacts dual functions controllers,
such as 1030. Please apply.
This patch also includes a small cosmetic name change
for mpt_spi_log_info.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] mptsas: don't complain on bogus slave_alloc calls
When people use the userspace scanning facilities on SAS hardware the
LLDD gets bogus slave_alloc calls. Just fail those gracefully instead
of printing a warning in mptsas and another one in the midlayer.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Mon, Jan 16, 2006 at 06:53:24PM -0700, Moore, Eric wrote:
> Adding MSI support, and command line for enabling
> it. By default, the command line option has MSI disabled.
mpt_msi_enable is initialized to 0 implicitly, no need to do that. Also
replace if (mpt_msi_enable == 1) tests with just if (mpt_msi_enable).
Updated patch below:
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Moore, Eric [Tue, 17 Jan 2006 01:53:19 +0000 (18:53 -0700)]
[SCSI] fusion: add verbose messages for RAID actions
A customer request to send raid asyn actions
from firmware to the event syslog. This shows
when raid volumes go degraded, or complete resync,
or volumes created/deleted, etc.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
[SCSI] fusion: setting timeouts in eh threads appropiatley for fc/sas/spi
On Mon, Jan 16, 2006 at 06:53:13PM -0700, Moore, Eric wrote:
> The task managment request timeout in the eh threads was set
> for U320 timing, which is between 2-5 seconds.
> This is too small for FC and SAS.
> According to the firmware engineers, Fibre needs to be 40 seconds
> and SAS needs to be 10 seconds.
The timeout selection should probably be done in a little helper instead
of duplicated in a few places. Updated patch below.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Moore, Eric [Tue, 17 Jan 2006 01:53:06 +0000 (18:53 -0700)]
[SCSI] fusion: spi bus reset when driver loads
This patch is for spi. This issues bus reset when driver
loads. Handling cases when initator has negotiated for packetized,
and target negotiated for non-packetized; effectly this bus reset
is getting both target and initiator on the same sheet of music.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hannes Reinecke [Mon, 30 Jan 2006 15:10:31 +0000 (16:10 +0100)]
[SCSI] aic79xx: Fix timer handling
Fix the timer handling in aic79xx to use the SCSI-ML provided handling
instead of implementing our own.
It also fixes a deadlock in the command recovery code.
Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Michael Reed [Thu, 26 Jan 2006 01:05:18 +0000 (18:05 -0700)]
[SCSI] fusion: FC rport code fixes
This fix's problems with recent fc submission regarding
i/o being redirected to the wrong target.
Signed-off-by: Michael Reed <mdr@sgi.com> Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Moore, Eric [Thu, 26 Jan 2006 23:20:06 +0000 (16:20 -0700)]
[SCSI] fusion: add support for raid hot add/del support
RAID event support.
This will hot add and remove raid volumes
when managment application creates and
deletes the volumes. The driver is basically
responding to firmware asyn events, and reporting
the changes to the above layers.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ingo Molnar [Wed, 25 Jan 2006 18:50:12 +0000 (19:50 +0100)]
[PATCH] rcu_torture_lock deadlock fix
rcu_torture_lock is used in a softirq-unsafe manner, but it is also
taken by rcu_torture_cb(), which may execute in softirq-context,
resulting in potential deadlocks.
The fix is to acquire rcu_torture_lock in a softirq-safe manner. With
this fix applied, the rcu-torture code passes validation.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Acked-by: Paul E. McKenney <paulmck@us.ibm.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Daniel Drake [Sat, 21 Jan 2006 19:35:34 +0000 (19:35 +0000)]
[PATCH] Clarify help text of SKGE/SK98LIN/SKY2
Some users have commented that it is unclear which driver they should be
using for their Marvell/SysKonnect network adapter, and which ones
are/aren't interchangable.
This patch attempts to reduce the confusion.
Signed-off-by: Daniel Drake <dsd@gentoo.org> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Baruch Even [Tue, 31 Jan 2006 04:54:39 +0000 (20:54 -0800)]
[TCP] H-TCP: Fix accounting
This fixes the accounting in H-TCP, the ccount variable is also
adjusted a few lines above this one.
This line was not supposed to be there and wasn't there in the patches
originally submitted, the four patches submitted were merged to one
and in that merge the bug was introduced.
Signed-Off-By: Baruch Even <baruch@ev-en.org> Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 31 Jan 2006 00:46:24 +0000 (16:46 -0800)]
[SPARC]: Fix compile failures in math-emu.
Kill debugging default switch cases in do_one_mathemu().
That case is handled properly already and gcc hates
the empty statement that results when the debug code is
disabled.
Pointed out by kaffe.
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Tue, 31 Jan 2006 00:00:40 +0000 (16:00 -0800)]
[SCTP]: heartbeats exceed maximum retransmssion limit
The number of HEARTBEAT chunks that an association may transmit is
limited by Association.Max.Retrans count; however, the code allows
us to send one extra heartbeat.
This patch limits the number of heartbeats to the maximum count.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: Sridhar Samudrala <sri@us.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log