Patrick McHardy [Wed, 26 Mar 2008 03:26:08 +0000 (20:26 -0700)]
[NETFILTER]: nf_nat_sip: split up SDP mangling
The SDP connection addresses may be contained in the payload multiple
times (in the session description and/or once per media description),
currently only the session description is properly updated. Split up
SDP mangling so the function setting up expectations only updates the
media port, update connection addresses from media descriptions while
parsing them and at the end update the session description when the
final addresses are known.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 03:25:32 +0000 (20:25 -0700)]
[NETFILTER]: nf_conntrack_sip: allow media expectations with wildcard source address
Media streams can come from anywhere, add a module parameter which
controls whether wildcard expectations or expectations between the
two signalling endpoints are created.
Since the same media description sent on multiple connections may
results in multiple identical expections when using a wildcard source,
we need to check whether a similar expectation already exists for a
different connection before attempting to register it.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Create expectations for incoming signalling connections when seeing
a REGISTER request. This is needed when the registrar uses a
different source port number for signalling messages and for receiving
incoming calls from other endpoints than the registrar.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 03:24:24 +0000 (20:24 -0700)]
[NETFILTER]: nf_conntrack_sip: introduce URI and header parameter parsing helpers
Introduce URI and header parameter parsing helpers. These are needed
by the conntrack helper to parse expiration values in Contact: header
parameters and by the NAT helper to properly update the Via-header
rport=, received= and maddr= parameters.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 03:22:37 +0000 (20:22 -0700)]
[NETFILTER]: nf_conntrack_sip: perform NAT after parsing
Perform NAT last after parsing the packet. This makes no difference
currently, but is needed when dealing with registrations to make
sure we seen the unNATed addresses.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 03:22:20 +0000 (20:22 -0700)]
[NETFILTER]: nf_conntrack_sip: support method specific request/response handling
Add support for per-method request/response handlers and perform SDP
parsing for INVITE/UPDATE requests and for all informational and
successful responses.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 03:18:40 +0000 (20:18 -0700)]
[NETFILTER]: nf_conntrack_sip: kill request URI "header" definitions
The request URI is not a header and needs to be treated differently than
real SIP headers. Add a seperate function for parsing it and get rid of
the POS_REQ_URI/POS_REG_REQ_URI definitions.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 03:17:55 +0000 (20:17 -0700)]
[NETFILTER]: nf_conntrack_sip: add seperate SDP header parsing function
SDP and SIP headers are quite different, SIP can have continuation lines,
leading and trailing whitespace after the colon and is mostly case-insensitive
while SDP headers always begin on a new line and are followed by an equal
sign and the value, without any whitespace.
Introduce new SDP header parsing function and convert all users that used
the SIP header parsing function. This will allow to properly deal with the
special SIP cases in the SIP header parsing function later.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 03:09:51 +0000 (20:09 -0700)]
[NETFILTER]: nf_nat_sip: fix NAT setup order
We need to set up the destination NAT mapping before the source NAT
mapping, so the NAT core gets to see the final tuple and can decide
whether the source port needs to be remapped.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 03:09:15 +0000 (20:09 -0700)]
[NETFILTER]: nf_conntrack: introduce expectation classes and policies
Introduce expectation classes and policies. An expectation class
is used to distinguish different types of expectations by the
same helper (for example audio/video/t.120). The expectation
policy is used to hold the maximum number of expectations and
the initial timeout for each class.
The individual classes are isolated from each other, which means
that for example an audio expectation will only evict other audio
expectations.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 03:08:37 +0000 (20:08 -0700)]
[NETFILTER]: nf_conntrack_expect: support inactive expectations
This is useful for the SIP helper and signalling expectations.
We don't want to create a full-blown expectation with a wildcard
as source based on a single UDP packet, but need to know the
final port anyways. With inactive expectations we can register
the expectation and reserve the tuple, but wait for confirmation
from the registrar before activating it.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Wed, 26 Mar 2008 03:07:38 +0000 (20:07 -0700)]
[NETFILTER]: nf_conntrack: fix NF_CT_TUPLE_DUMP for IPv4
NF_CT_TUPLE_DUMP prints IPv4 addresses as IPv6, fix this and use printk
(guarded by #ifdef DEBUG) directly instead of pr_debug since the tuple
is usually printed at the end of line and we don't want to include a
log-level.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Ivo van Doorn [Tue, 25 Mar 2008 13:13:18 +0000 (14:13 +0100)]
rt2x00: Fix in_atomic() usage
rt73usb and rt2500usb used in_atomic to determine
if a configuration step should be rescheduled or not.
Since in_atomic() is not a valid method to determine
if sleeping is allowed we should fix the way this is handled
by adding a new flag to rt2x00.
In addition mark LED class support for the drivers broken
since that also uses the broken in_atomic() method but
so far no solution exists to have LED triggers work only
in scheduled context.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Tue, 25 Mar 2008 13:12:45 +0000 (14:12 +0100)]
rt2x00: Fix rate detection for invalid signals
It has been observed on rt2500pci hardware that some
frames received with signal 0x0C do not have the OFDM
flag set.
Signals can have 2 meanings:
1) The PLCP value
2) The bitrate * 10
For rt2500pci (1) is for frames received with a OFDM rate,
and (2) is for frames received with a CCK rate.
But 0x0C is a invalid bitrate value but is a valid PLCP
value for 54Mbs (obvious OFDM rate).
This means that it is possible that the hardware does not
set the OFDM bit correctly under all circumstances.
This results in rt2x00 failing to detect the rate and
mac80211 triggering a WARN_ON() and dropping the frame.
To bypass this, print a warning when such a frame is received,
and reset the rate to the lowest supported rate for the current band.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assaf Krauss [Tue, 18 Mar 2008 21:57:50 +0000 (14:57 -0700)]
iwlwifi: Completing the parameter packaging
This patch completes the changes regarding the packaging of user
parameters.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Al Viro [Sun, 16 Mar 2008 22:26:44 +0000 (22:26 +0000)]
ipw2200 annotations and fixes
a) a bunch of printks in error-handling assums that ->status is
big-endian.
b) bitfields trouble
c) missing annotations
NB: a bunch of structs is declared packed for no good reason, AFAICS.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Acked-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Sat, 15 Mar 2008 20:38:07 +0000 (21:38 +0100)]
rt2x00: Add dev_flags to rx descriptor
The rxdone_entry_desc structure contains 3 fields
which are always 1 or 0. We can safe 8 bytes by
replacing them with a single dev_flags fields which
contain the flags for those settings.
Additionally we can remove the OFDM flag since it
is no longer used since the introduction of the
SIGNAL_PLCP flag.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Koutny [Tue, 18 Mar 2008 20:14:07 +0000 (21:14 +0100)]
mac80211: configure default wmm params correctly
Default WMM params have to be set according to beacon/probe response
information prior to authentication (or IBSS start/join); beacon queue
is configured only in IBSS. This does not affect the use of 'real' WMM
params as reported by AP.
Signed-off-by: Vladimir Koutny <vlado@ksp.sk> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Thu, 20 Mar 2008 15:14:29 +0000 (08:14 -0700)]
mac80211: prevent tuning during scanning
Postpone calling ieee80211_hw_config if hardware scanning is active.
This is similar to solution for software scanning where channel setting
is delayed until scan complete.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Acked-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Tue, 18 Mar 2008 22:00:32 +0000 (15:00 -0700)]
mac80211: tear down of block ack sessions
This patch adds a clean tear down for all block ack sessions if interface
goes down or if a deauthentication is done.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Tue, 18 Mar 2008 22:00:31 +0000 (15:00 -0700)]
mac80211: fixing debug prints for AddBA request
This patch also fixes the Rx timer's comments
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Tue, 18 Mar 2008 22:00:30 +0000 (15:00 -0700)]
mac80211: fixing delba debug print
This patch fixes a wrong debug print when receiving delba
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Sun, 16 Mar 2008 17:42:44 +0000 (18:42 +0100)]
mac80211: filter scan results on unusable channels
When you have an AP on channel 13, it will currently often enough
be listed in scan results even when the regulatory domain restricts
to channels 1-11. This is due to channel overlap. To avoid getting
very strange failures, don't show such APs in the scan results. The
failure mode will now go from "I can see the AP but not associate"
to "I can't see the AP although I know it's there" which is easier
to debug.
This problem was first really noticed by Jes Sorensen.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Cc: Jes Sorensen <jes@trained-monkey.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 21 Mar 2008 20:53:44 +0000 (13:53 -0700)]
iwlwifi: move host command sending functions to core module
1. Host command sending functions moved from iwl4965-base.c to iwl-hcmd.c
in iwlcore module
2. enqueue_hcmd function currently stays in iwl4965-base.c. It is invoked
through the new 'utils' field in priv's ops.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assaf Krauss [Fri, 21 Mar 2008 20:53:43 +0000 (13:53 -0700)]
iwlwifi: rename iwl4965_get_channel_info to iwl_get_channel_info
iwl4965_get_channel_info was moved to iwlcore module
4965 needs to be stripped off
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Fri, 21 Mar 2008 20:53:42 +0000 (13:53 -0700)]
iwlwifi: iwl3945 remove 4965 commands
This patch removes 4965 host commands from iwl-3945-commands.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add support for TKIP encryption (TX) in HW.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211: allows driver to request a Phase 1 RX key
This patch makes mac80211 able to send a phase1 key for TKIP
decryption.
This is needed for drivers that don't do the rekeying by themselves
(i.e. iwlwifi). Upon IV16 wrap around, the packet is decrypted in SW,
if decryption is ok, mac80211 calls to update_tkip_key with a new
phase 1 RX key.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 able to compute a TKIP key from an skb.
The requested key can be a phase 1 or a phase 2 key.
This is useful for drivers who need to provide tkip key to their
HW to enable HW encryption.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds translation for the RX status of an incoming packet.
The incoming status has to be translated to the old scheme in order to know
if the decryption has been done, MIC failure has occured, TTAK is valid etc...
This translation is mandatory for all RX packets when using 5300 and for
all HT packets using 4965.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up the set_key flow. Rxon with hw encryption bit set is
not sent upon each call to set_key. Separation is made between global key
(WEP) and dynamic key (TKIP + CCMP and WEP in some cases).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assaf Krauss [Fri, 14 Mar 2008 17:38:49 +0000 (10:38 -0700)]
iwlwifi: Probe Flow - Extracting hw and priv init
1. Extracting hw and priv initialization from probe function.
2. Moving some initialization functions to core module.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assaf Krauss [Fri, 14 Mar 2008 17:38:48 +0000 (10:38 -0700)]
iwlwifi: Probe Flow - Performing allocation in a separate function
Performing allocation in a separate function (previously handled in
'probe')
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assaf Krauss [Fri, 14 Mar 2008 17:38:47 +0000 (10:38 -0700)]
iwlwifi: Packing all 4965 parameters
This patch defines a package struct for iwlwifi parameters, and uses a
single instance of this struct to group all iwl4965 module parameters
together.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assaf Krauss [Fri, 14 Mar 2008 17:38:46 +0000 (10:38 -0700)]
iwlwifi: Re-ordering probe flow (4965)
This patch re-orders the iwl4965_pci_probe function.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 19 Mar 2008 16:08:32 +0000 (17:08 +0100)]
libertas: store rssi as an u32
Don't store an (hardware base) u8 value in bss_descriptor, but just an
unsigned int (RSSI is really unsigned). Compilers generate more efficent
code for ints than for bytes.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 19 Mar 2008 13:25:58 +0000 (14:25 +0100)]
libertas: remove lots of unused stuff
This removes many unused function parameters as well as some not-implemented
functions, e.g. CMD_802_11_GET_STATS. The silly lbs_set_cmd_ctrl_node()
function is now also gone.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 19 Mar 2008 13:25:18 +0000 (14:25 +0100)]
libertas: misc power saving adjusts
* firmware for the CF card supports power saving
* the driver currenly only accept "iwconfig ethX power on|off", so
I fixed what the range wext ioctl reports.
* initialize value/flags in lbs_get_power()
* get rid of unused parameter psmode in lbs_ps_confirm_sleep()
* some minor debug output tweaks
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Mon, 17 Mar 2008 11:45:58 +0000 (12:45 +0100)]
libertas: convert GET_LOG to a direct command
Now uses __lbs_cmd() to get the "log" (it's actually more a snapshot of
various counters, not a sequential log). Besides the "mechanical" convertion
the patch add the following logical changes:
* Removes the priv->logmsg variable, it was only used in one place anyway,
also don't blindly get the counters when associating. Getting the
counters then the user asks via WEXT for them is good enought.
* don't set wstats.discard.fragment with log.rxfrag, because the latter is
a counter for successfully received packets, not for fragmented packets.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Tue, 18 Mar 2008 10:20:21 +0000 (11:20 +0100)]
libertas: fix scheduling while atomic bug in CMD_MAC_CONTROL
The old code incorrectly used lbs_cmd_with_response() and now uses
lbs_cmd_async().
While there I noticed that there is no real useful return values for
asynchronous command functions, so I made the function "void".
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 19 Mar 2008 09:11:00 +0000 (10:11 +0100)]
libertas: make a handy lbs_cmd_async() command
This uses a static lbs_cmd_async_callback function, which is a
noop. Just setting the callback argument to __lbs_cmd_async()
to NULL won't work, because then the cmdnode wouldn't be
released.
This also makes __lbs_cmd_async() a static method, which is
now only used by lbs_cmd() and lbs_cmd_async().
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 12 Mar 2008 23:58:52 +0000 (16:58 -0700)]
iwlwifi: Add debugfs to iwl core
This patch adds debugfs support to iwl core
currently only iwl4965 is supported
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 12 Mar 2008 23:58:51 +0000 (16:58 -0700)]
iwlwifi: Add TX/RX statistcs to driver
This patch supports collecting of TX and RX statistics in the driver.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 12 Mar 2008 23:58:50 +0000 (16:58 -0700)]
iwlwifi: rename struct iwl4965_priv to struct iwl_priv
This patch renames iwl4965_priv to iwl_priv. iwl_priv will
be shared by more hw.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 12 Mar 2008 23:58:49 +0000 (16:58 -0700)]
iwlwifi: rename iwl-4965-debug.h back to iwl-debug.h
This patch removes iwl-4965-debug.h to iwl-debug.h
It will be used by more NICs
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: Reinette Chatre <reinette.chatre@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Max Stepanov [Wed, 12 Mar 2008 23:58:48 +0000 (16:58 -0700)]
iwlwifi: Bug fix, CCMP with HW encryption with AGG
This patch fixes a bug in security. Enables CCMP HW encryption with
aggregations.
Signed-off-by: Max Stepanov <max.stepanov@intel.com> Signed-off-by: Tomas Winkler <tomas.winkler@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 12 Mar 2008 16:06:09 +0000 (17:06 +0100)]
libertas: remove some unused commands
Neither CMD_802_11_PAIRWISE_TSC nor CMD_802_11_GROUP_TSC is used or
documented. It might have something to do with TKIP sequence counters,
but that's just an educated guess. Remove all occurences of them.
CMD_CODE_DNLD is also neither used nor documented.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 12 Mar 2008 15:06:43 +0000 (16:06 +0100)]
libertas: rename packetfilter to mac_control
The CMD_MAC_CONTROL can be used for other things than just filtering
packets, e.g. to enable and disable WMM. This uses the same term mac_control
for the define, the function and the shadow value in struct lbs_private.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
Holger Schurig [Wed, 12 Mar 2008 15:05:40 +0000 (16:05 +0100)]
libertas: convert CMD_MAC_CONTROL to a direct command
convert CMD_MAC_CONTROL to a direct command
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
[NET] NETNS: Omit neigh_parms->net and pneigh_entry->net without CONFIG_NET_NS.
Introduce neigh_parms/pneigh_entry inlines: neigh_parms_net(), pneigh_net().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
[NET] NETNS: Omit sock->sk_net without CONFIG_NET_NS.
Introduce per-sock inlines: sock_net(), sock_net_set()
and per-inet_timewait_sock inlines: twsk_net(), twsk_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
[NET] NETNS: Omit net_device->nd_net without CONFIG_NET_NS.
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Each MIPv6 XFRM state (DSTOPT/RH2) holds either destination or source
address to be mangled in the IPv6 header (that is "CoA").
On Inter-MN communication after both nodes binds each other,
they use route optimized traffic two MIPv6 states applied, and
both source and destination address in the IPv6 header
are replaced by the states respectively.
The packet format is correct, however, next-hop routing search
are not.
This patch fixes it by remembering address pairs for later states.
Based on patch from Masahide NAKAMURA <nakam@linux-ipv6.org>.
Denis V. Lunev [Mon, 24 Mar 2008 22:33:00 +0000 (15:33 -0700)]
[NETNS]: Drop packets in the non-initial namespace on the per/protocol basis.
IP layer now can handle multiple namespaces normally. So, process such
packets normally and drop them only if the transport layer is not
aware about namespaces.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis V. Lunev [Mon, 24 Mar 2008 22:32:09 +0000 (15:32 -0700)]
[NETNS]: Process netfilter hooks in initial namespace only.
There were no packets in the namespace other than initial
previously. This will be changed in the neareast future. Netfilters
are not namespace aware and should be processed in the initial
namespace only for now.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Denis V. Lunev [Mon, 24 Mar 2008 22:29:23 +0000 (15:29 -0700)]
[NETNS]: Add namespace parameter to ip_options_compile.
ip_options_compile uses inet_addr_type which requires a namespace. The
packet argument is optional, so parameter is the only way to obtain
it. Pass the init_net there for now.
Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
projects / linux-2.6 / log