Hans de Goede [Thu, 3 Jul 2008 14:20:58 +0000 (11:20 -0300)]
V4L/DVB (8194): gspca: Fix the format of the low resolution mode of spca561.
The low (half) res modes of the spca561 are not spca561 compressed, but are
raw bayer, this patches fixes this and adds a PIX_FMT define for the GBRG
bayer format used by the spca561 in low res mode.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andy Walls [Mon, 7 Jul 2008 13:36:16 +0000 (10:36 -0300)]
V4L/DVB (8189): cx18: Use correct GPIO pin for resetting Xceive 3028 tuner on Yuan MPC718
Change the Yuan MPC718 cards entry to use the correct GPIO pin for resetting
the Xceive 3028 tuner. Thanks to Brian Hope <brian@hopefamily.info> for
taking the time and figuring out which pin to use.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (8181): gspca: read() did not work (loop in kernel, timeout...)
main: Remove some vidioc_xx traces.
main: read() did not work (user irq instead of mmap irq).
main: Lack of v4l1 compat.
main: Process loop inside kernel when no frame arriving.
main: Double qbuf in read() when too many buffered frames.
Hans Verkuil [Fri, 27 Jun 2008 18:33:02 +0000 (15:33 -0300)]
V4L/DVB (8162): cx18: fix PAL/SECAM support
Reverted the 'Fix unintended auto configurations in cx18-av-core' patch,
instead disable the auto config completely.
Fix a bug in cx18_av_vbi_setup() where the standard tests were done
in the wrong order.
Tested with NTSC-M, PAL-BG, PAL-I, PAL-DK, PAL-M, PAL-Nc, SECAM-DK,
SECAM-L and SECAM-BG. The last one does not work at the moment due to
a tda9887.c bug.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
main: V4L2_PIX_FMT_SPCA501 is compressed (thanks to Hans de Goede)
main: return 0 when no change on vidioc_s_fmt_cap (thanks to Hans de Goede)
pac207: cleanup
V4L/DVB (8154): Fix protection problems in the main driver.
- Protect format change when streaming active.
- Protect USB exchanges on close.
- Set a timeout in frame wait.
- Have only one capture file and free the resources when closing this file.
- Simplify the URB buffer.
- Don't reset the control values at open time in pac207.
- Fix compilation warnings of stk014.
Al Viro [Sun, 22 Jun 2008 17:20:49 +0000 (14:20 -0300)]
V4L/DVB (8126): net endianness fix
According to RFC 4326 (4.1) D-bit is MSB in net-endian 16bit.
dvb_net.c did
/* Set D-bit for CRC32 verification,
* if it was set originally. */
ulen |= 0x0080;
which works of little-endian (htons(1<<15) is 0x0080 there), but breaks
on big-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L/DVB (8123): Add support for em2860 based PointNix Intra-Oral Camera
em28xx-cards.c
em28xx-input.c
em28xx-video.c
em28xx.h
- Add support for the PointNix Intra-Oral Camera, which required addition of
a construct for reading the "snapshot" button (provided on the em2860 and
em2880 chips, but this is the first case where I have seen it actually used
in a product). The button is wired to pin 56 on the em2880.
http://www.pointnix.com/ENG/dental/product_02.asp
Thanks to Roberto Mantovani <rmantovani@libero.it> for testing the changes
Hans Verkuil [Wed, 25 Jun 2008 09:54:05 +0000 (06:54 -0300)]
V4L/DVB (8116): videodev: allow PRIVATE_BASE controls when called through VIDIOC_G/S_CTRL.
V4L2_CID_PRIVATE_BASE controls are not allowed when called from
VIDIOC_S/G_EXT_CTRL as extended controls use a better mechanism
for private controls. But still allow it when called from the
VIDIOC_G/S_CTRL to extended control conversion in video_ioctl2()
for backwards compatibility.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Improved Raptor card audio input routing defintions, so that muxer values
matched cx18_gpio() values for tuner, line in 1, and radio and added LED
indication of selected audio input. Audio line in 2 doesn't work as it uses
the not yet supported 2nd I2S port. Tuner/FM Radio AF is mono until SIF
support is fixed.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil [Wed, 25 Jun 2008 09:29:01 +0000 (06:29 -0300)]
V4L/DVB (8112): videodev: improve extended control support in video_ioctl2()
- add sanity checks for the extended controls argument.
- if the driver only supports extended controls, then convert
old-style controls to an extended control callback.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- use %x rather than %d for control IDs and bitmask fields
- make two arrays const
- show the whole control array for the ext_ctrl ioctls
- print pix_fmt for V4L2_BUF_TYPE_VIDEO_OUTPUT
- show full type name rather than an integer
- fix CROPCAP debugging
- fix G/S_TUNER debugging
- show error code in case of an error
- other small cleanups
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 22 Jun 2008 01:13:42 +0000 (22:13 -0300)]
V4L/DVB (8098): xc5000: add module option to load firmware during driver attach
The xc5000 firmware download process can be slow on certain devices.
Add a module option, "init_fw" to perform the firmware download during
xc5000_attach(), which would get the firmware download over with well
before any tune request is made.
When this option is enabled, it will reduce the time it takes to get a
signal lock during the first tune after driver load, but will add a few
seconds to the driver initialization.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Sat, 21 Jun 2008 14:09:46 +0000 (11:09 -0300)]
V4L/DVB (8090): ivtv: yuv decoder lock fix (2)
The IVTV_IOC_DMA_FRAME ioctl fails to correctly 'start' the decoder. Although
yuv output will be correct, some functions which should be disabled while the
decoder is in use remain enabled. This can result in hardware registers being
corrupted, causing problems with the mpeg decoder. This patch ensures the
decoder 'start' sequence is called, disabling these functions until the
device is closed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ian Armstrong [Sat, 21 Jun 2008 12:25:23 +0000 (09:25 -0300)]
V4L/DVB (8088): ivtv: yuv decoder lock fix
write() operations to the yuv device may not always 'start' the decoder.
Although yuv output will be correct, some functions which should be disabled
while the decoder is in use remain enabled. This can result in hardware
registers being corrupted, causing problems with the mpeg decoder. This patch
simply moves the existing decoder 'start' sequence to earlier in the write()
handler.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the capture is scaled, then the video_temporal_filter is set to 0
by the cx2341x.c module since otherwise you would get ghosting.
However, this was also done in the VIDIOC_S_FMT ioctl which meant that
the video_temporal_filter control was reset to 0 or 8 each time S_FMT
was called. This was old code that should have been removed a long time
ago.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andy Walls [Sat, 21 Jun 2008 11:36:31 +0000 (08:36 -0300)]
V4L/DVB (8082): cx18: convert to video_ioctl2()
cx18: convert driver to use video_ioctl2(). Pushed down ioctl debug
messages and priority checks as well. Still left serialization lock in
place for now. #if 0'ed out sliced vbi ioctl code for now.
Patch heavily based on similar changes made to ivtv by Hans Verkuil.
Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
brandon@ifup.org [Sat, 21 Jun 2008 01:58:53 +0000 (22:58 -0300)]
V4L/DVB (8078): Introduce "index" attribute for persistent video4linux device nodes
A number of V4L drivers have a mod param to specify their preferred minors.
This is because it is often desirable for applications to have a static /dev
name for a particular device. However, using minors has several disadvantages:
1) the requested minor may already be taken
2) using a mod param is driver specific
3) it requires every driver to add a param
4) requires configuration by hand
This patch introduces an "index" attribute that when combined with udev rules
can create static device paths like this:
Michael Krufky [Tue, 17 Jun 2008 18:32:08 +0000 (15:32 -0300)]
V4L/DVB (8060): Kconfig: MEDIA_TUNER_CUSTOMIZE should be disabled by default
The build option, MEDIA_TUNER_CUSTOMIZE, allows us to disable tuner drivers
that would have otherwise been selected by default. This is an advanced
customization option that should be disabled by default.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Sigmund Augdal [Sun, 15 Jun 2008 20:25:46 +0000 (17:25 -0300)]
V4L/DVB (8049): budget-ci: Add support for Technotrend budget C-1501 dvb-c card
The following experimental patch adds support for the technotrend budget
C-1501 dvb-c card. The parameters used to configure the tda10023 demod
chip are largely determined experimentally, but works quite for me in my
initial tests.
Clean up the use of structure templates in bttv-i2c. For one thing, a
real template is supposed to be read-only. And in some cases it's more
efficient to initialize the few fields we need individually.
This clean-up shrinks bttv-i2c.o by 29% (x86_64).
Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Clean up the use of structure templates in zoran_card. For one thing,
a real template is supposed to be read-only. And in some cases it's
more efficient to initialize the few fields we need individually.
Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Dmitry Belimov [Tue, 10 Jun 2008 17:22:00 +0000 (14:22 -0300)]
V4L/DVB (8021): Beholder's cards description
Split the Beholder M6 family to different models. Because M6 hasn`t RDS, M63
has chip with AC3 codec, M6 Extra has other type of HF module.
Add correct data for support MPEG encoder.
Dmitry Belimov [Tue, 10 Jun 2008 15:43:58 +0000 (12:43 -0300)]
V4L/DVB (8019): New for I2S on for MPEG of saa7134_empress
Rework saa7134_enable_i2s function. Remove vendor specific data.
Configure I2S output port specific for model of SAA7133/5-SAA7134.
I think it is more good.
Renamed definition of I2S audio output control register. It`s SAA7133/5 register
Start video port after configuring procedure.
projects / linux-2.6 / log