Alan Stern [Fri, 11 Aug 2006 20:01:45 +0000 (16:01 -0400)]
usbcore: make hcd_endpoint_disable wait for queue to drain
The inconsistent lock state problem in usbcore (the one that shows up
when an HCD is unloaded) comes down to two inter-related problems:
usb_rh_urb_dequeue() isn't set up to be called with interrupts
disabled.
hcd_endpoint_disable() doesn't wait for all URBs on the
endpoint's queue to complete.
The two problems are related because the one type of URB that isn't
likely to be complete when hcd_endpoint_disable() returns is a root-hub
URB. Right now usb_rh_urb_dequeue() waits for them to complete, and it
assumes interrupts are enabled so it can wait. But
hcd_endpoint_disable() calls it with interrupts disabled.
Now, it should be legal to unlink root-hub URBs with interrupts
disabled. The solution is to move the waiting into
hcd_endpoint_disable(), where it belongs. This patch (as754) does that.
It turns out to be completely safe to replace the del_timer_sync() with
a simple del_timer(). It doesn't matter if the timer routine is
running; hcd_root_hub_lock will synchronize the two threads and the
status URB will complete with an unlink error, as it should.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 11 Aug 2006 15:33:58 +0000 (11:33 -0400)]
UHCI: increase Resume-Detect-off delay
The UHCI controller in my laptop takes longer to turn off the
Resume-Detect bit than the 4 us allowed by uhci-hcd. Presumably other
computers will have the same problem.
This patch (as752) increases the maximum delay to 10 us, which should be
plenty, and uses polling to avoid penalizing systems which can turn the
bit off more quickly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Aleksey Gorelov [Wed, 9 Aug 2006 00:24:08 +0000 (17:24 -0700)]
USB: Properly unregister reboot notifier in case of failure in ehci hcd
If some problem occurs during ehci startup, for instance, request_irq fails,
echi hcd driver tries it best to cleanup, but fails to unregister reboot
notifier, which in turn leads to crash on reboot/poweroff.
The following patch resolves this problem by not using reboot notifiers
anymore, but instead making ehci/ohci driver get its own shutdown method. For
PCI, it is done through pci glue, for everything else through platform driver
glue.
One downside: sa1111 does not use platform driver stuff, and does not have its
own shutdown hook, so no 'shutdown' is called for it now. I'm not sure if it
is really necessary on that platform, though.
Signed-off-by: Aleks Gorelov <dared1st@yahoo.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These functions makes USB driver's code simpler when dealing with endpoints
by avoiding them from accessing the endpoint's descriptor structure directly
when they only need to know the endpoint's transfer type and/or
direction.
Please, read each functions' documentation in order to know how to use
them.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: making the kernel -Wshadow clean - USB & completion
include/linux/usb.h causes a lot of -Wshadow warnings - fix them.
include/linux/usb.h:901: warning: declaration of 'complete' shadows a global declaration
include/linux/completion.h:52: warning: shadowed declaration is here
include/linux/usb.h:932: warning: declaration of 'complete' shadows a global declaration
include/linux/completion.h:52: warning: shadowed declaration is here
include/linux/usb.h:967: warning: declaration of 'complete' shadows a global declaration
include/linux/completion.h:52: warning: shadowed declaration is here
Ben Williamson [Tue, 1 Aug 2006 01:28:16 +0000 (11:28 +1000)]
USB: gmidi: New USB MIDI Gadget class driver.
This driver is glue between the USB gadget interface
and the ALSA MIDI interface. It allows us to appear
as a MIDI Streaming device to a host system on the
other end of a USB cable.
This includes linux/usb/audio.h and linux/usb/midi.h
containing definitions from the relevant USB specifications
for USB audio and USB MIDI devices.
The following changes have been made since the first RFC
posting:
* Bug fixes to endpoint handling.
* Workaround for USB_REQ_SET_CONFIGURATION handling,
not understood yet.
* Added SND and SND_RAWMIDI dependencies in Kconfig.
* Moved usb_audio.h and usb_midi.h to usb/*.h
* Added module parameters for ALSA card index and id.
* Added module parameters for USB descriptor IDs and strings.
* Removed some unneeded stuff inherited from zero.c, more to go.
* Provide DECLARE_* macros for the variable-length structs.
* Use kmalloc instead of usb_ep_alloc_buffer.
* Limit source to 80 columns.
* Return actual error code instead of -ENOMEM in a few places.
Signed-off-by: Ben Williamson <ben.williamson@greyinnovation.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Milan Svoboda [Mon, 26 Jun 2006 14:19:00 +0000 (07:19 -0700)]
USB: fix ep_config to return correct value
This patch fixes ep_config to return correct value. Without patch
ep_config returns submitted lenght minus 4 on succes. With this
patch applied, whole submitted lenght is returned.
ep_config parses submitted data and if buffer starts with (int) 1
it is parsed, otherwise error is reported. Problem is that ep_config
returns size of buffer minus 4 on success. I think that size of buffer
should be returned instead, because there were no problems and
all data were processed.
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Mon, 31 Jul 2006 14:29:39 +0000 (07:29 -0700)]
USB: build fixes: ohci-omap
The ohci-omap code has diverged from the working version in the linux-omap
tree; this syncs up the versions:
- Another clock is needed in various cases
- The omap-1510 iommu code needs to be #ifdeffed out on newer parts
- Saner use of the HCD framework
- Various other changes, e.g. a Nokia 770 quirk
And some minor dead-whitespace removal.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- split wacom.c into 4 files: wacom.h, wacom_wac.h, wacom_sys.c, and wacom_wac.c
- where wacom_sys.c deals with system specific code,
- and wacom_wac.c deals with Wacom specific code
USB: usbcore get rid of the timer in usb_start_wait_urb()
This patch uses completion timeout instead of a timer to implement
a timeout when submitting an URB in usb_start_wait_urb().
It also fixes a small issue. With the previous code, if no timeout
happened and the URB's status was set to ECONNRESET value, the code
assumed wrongly that a timeout had occured.
Commit b512504e5671f83638be0ddr085c4b1832f623d3 made ipaq_open() a bit
messy by moving the read urb submission far from its usb_fill_bulk_urb()
call and the comment explaining what it does.
This patch put they together again. Although only compiled tested, should
not break the fix introduced by b512504e5671f83638be0ddr085c4b1832f623d3,
of course.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Randy Dunlap [Mon, 7 Aug 2006 22:56:40 +0000 (15:56 -0700)]
usbnet: printk format warning
Fix printk format warning(s):
drivers/usb/net/usbnet.c:654: warning: int format, different type arg (arg 3)
The fact that rx_urb_size happens to be a size_t has propagated all the way
back to this printk. It's fragile to be using %z in this case - let's just
typecast the args instead.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB: pl2303: cosmetic changes to pl2303_buf_{clear, data_avail}
Changes the functions pl2303_buf_clear and pl2303_buf_data_avail for
the purpose of keeping them under the 80 column limit, making them
more similar to similar functions and making then simpler.
Daniel Ritz [Mon, 31 Jul 2006 19:43:24 +0000 (21:43 +0200)]
usbtouchscreen: version 0.4
changes over 0.3:
- some more eGalax device IDs (from eGalax driver/spec)
- return the error code in probe()
- 3M/MTouch init fixes, tested by Don Alexander
- eGalax fixes for bugs in multi-packet handling, spottet by Pieter Grimmerink
- support for some eTurboTouch devices, mostly by Pieter Grimmerink
- support for Gunze AHL61 controller (untested, but simple enough)
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch> Cc: Pieter Grimmerink <p.grimmerink@inepro.com> Cc: Don Alexander <debug@roosoft.ltd.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:13:50 +0000 (22:13 -0400)]
usbcore: suspending devices with no driver
Since usb_generic can be unbound from a USB device, we need to be able
to handle the possibility that a suspend or resume request arrives for a
device with no driver. This patch (as735) arranges things so that
resume requests will fail and suspend requests will use the standard USB
port-suspend code. Attempts to suspend or resume an unbound interface
are handled similarly (although the error caused by trying to resume an
unbound interface is dropped by the calling routine).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:13:04 +0000 (22:13 -0400)]
usbcore: fix up device and power state tests
This patch (as734) rationalizes the various tests of device state and
power states. There are duplications and mistaken tests in several
places.
Perhaps the most interesting challenge is where the hub driver tests to
see that all the child devices are suspended before allowing itself to
be suspended. When CONFIG_USB_SUSPEND is set the test is
straightforward, since we expect that the children _will_ be suspended.
But when CONFIG_USB_SUSPEND isn't set, it's not so clear what should be
done. The code compromises by checking the child's
power.power_state.event field.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:12:19 +0000 (22:12 -0400)]
usbcore: set device and power states properly
This patch (as733) fixes up the places where device states and power
states are set in usbcore. Right now things are duplicated or missing;
this should straighten things out.
The idea is that udev->state is USB_STATE_SUSPENDED exactly when the
device's upstream port has been suspended, whereas
udev->dev.power.power_state.event reflects the result of the last call
to the suspend/resume routines (which might not actually change the
device state, especially if CONFIG_USB_SUSPEND isn't set).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:11:44 +0000 (22:11 -0400)]
usbcore: track whether interfaces are suspended
Currently we rely on intf->dev.power.power_state.event for tracking
whether intf is suspended. This is not a reliable technique because
that value is owned by the PM core, not by usbcore. This patch (as718b)
adds a new flag so that we can accurately tell which interfaces are
suspended and which aren't.
At first one might think these flags aren't needed, since interfaces
will be suspended along with their devices. It turns out there are a
couple of intermediate situations where that's not quite true, such as
while processing a remote-wakeup request.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:11:02 +0000 (22:11 -0400)]
usbcore: resume device resume recursion
This patch (as717b) removes the existing recursion in hub resume code:
Resuming a hub will no longer automatically resume the devices attached
to the hub.
At the same time, it adds one level of recursion: Suspending a USB
device will automatically suspend all the device's interfaces. Failure
at an intermediate stage will cause all the already-suspended interfaces
to be resumed. Attempts to suspend or resume an interface by itself will
do nothing, although they won't return an error. Thus the regular
system-suspend and system-resume procedures should continue to work as
before; only runtime PM will be affected.
The patch also removes the code that tests state of the interfaces
before suspending a device. It's no longer needed, since everything
gets suspended together.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:10:15 +0000 (22:10 -0400)]
usbcore: split suspend/resume for device and interfaces
This patch (as716b) splits up the core suspend and resume routines into
two parts each: one for handling devices and one for handling
interfaces. The behavior of the parts should be the same as in the old
unified code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:09:35 +0000 (22:09 -0400)]
usbcore: make usb_generic a usb_device_driver
This patch (as714b) makes usb_generic into a usb_device_driver capable
of being probed and unbound, just like other drivers. A fair amount of
the work that used to get done during discovery or removal of a USB
device have been moved to the probe and disconnect methods of
usb_generic: creating the sysfs attributes and selecting an initial
configuration. However the normal behavior should continue to be the
same as before.
We will now have the possibility of creating other USB device drivers,
They will assist with exporting devices to remote systems
(USB-over-TCPIP) or to paravirtual guest operating systems.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:08:49 +0000 (22:08 -0400)]
usbcore: add usb_device_driver definition
This patch (as732) adds a usb_device_driver structure, for representing
drivers that manage an entire USB device as opposed to just an
interface. Support routines like usb_register_device_driver,
usb_deregister_device_driver, usb_probe_device, and usb_unbind_device
are also added.
Unlike an earlier version of this patch, the new code is type-safe. To
accomplish this, the existing struct driver embedded in struct
usb_driver had to be wrapped in an intermediate wrapper. This enables
the core to tell at runtime whether a particular struct driver belongs
to a device driver or to an interface driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:08:06 +0000 (22:08 -0400)]
usbcore: move code among source files
This revised patch (as713b) moves a few routines among source files in
usbcore. Some driver-related code in usb.c (claiming interfaces and
matching IDs) is moved to driver.c, where it belongs. Also the
usb_generic stuff in driver.c is moved to a new source file: generic.c.
(That's the reason for revising the patch.) Although not very big now,
it will get bigger in a later patch.
None of the code has been changed; it has only been re-arranged.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:07:21 +0000 (22:07 -0400)]
usbcore: rename usb_suspend_device to usb_port_suspend
This revised patch (as715b) renames usb_suspend_device to
usb_port_suspend, usb_resume_device to usb_port_resume, and
finish_device_resume to finish_port_resume. There was no objection to
the original version of the patch so this should be okay to apply.
The revision was needed only because I have re-arranged the order of the
earlier patches.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:06:36 +0000 (22:06 -0400)]
usb-skeleton: don't submit URBs after disconnection
This patch (as712b) is a slight revision of one submitted earlier. It
fixes the usb-skeleton example driver so that it won't try to submit
URBs after skel_disconnect() has returned. This could cause errors, if
the driver was unbound and then a different driver was bound to the
device. It also fixes a couple of small bugs in the skel_write()
routine.
The revised patch uses a slightly different test, suggested by Dave
Brownell, for determining whether to free a transfer buffer. It's a
little clearer than the earlier version.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:05:56 +0000 (22:05 -0400)]
usbfs: detect device unregistration
This patch (as711b) is a revised version of an earlier submission. It
modifies the usbfs code to detect when a device has been unregistered from
usbfs, even if the device is still connected. Although this can't happen
now, it will be able to happen after the upcoming changes to usb_generic.
Nobody objected to this patch when it was submitted before, so it should
be okay to apply this version. The revision is merely to take into
account the changes introduced by as723, which touches the same driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Sun, 2 Jul 2006 02:05:01 +0000 (22:05 -0400)]
usbfs: private mutex for open, release, and remove
The usbfs code doesn't provide sufficient mutual exclusion among open,
release, and remove. Release vs. remove is okay because they both
acquire the device lock, but open is not exclusive with either one. All
three routines modify the udev->filelist linked list, so they must not
run concurrently.
Apparently someone gave this a minimum amount of thought in the past by
explicitly acquiring the BKL at the start of the usbdev_open routine.
Oddly enough, there's a comment pointing out that locking is unnecessary
because chrdev_open already has acquired the BKL.
But this ignores the point that the files in /proc/bus/usb/* are not
char device files; they are regular files and so they don't get any
special locking. Furthermore it's necessary to acquire the same lock in
the release and remove routines, which the code does not do.
Yet another problem arises because the same file_operations structure is
accessible through both the /proc/bus/usb/* and /dev/usb/usbdev* file
nodes. Even when one of them has been removed, it's still possible for
userspace to open the other. So simple locking around the individual
remove routines is insufficient; we need to lock the entire
usb_notify_remove_device notifier chain.
Rather than rely on the BKL, this patch (as723) introduces a new private
mutex for the purpose. Holding the BKL while invoking a notifier chain
doesn't seem like a good idea.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 6 Jul 2006 19:37:42 +0000 (15:37 -0400)]
usbcore: add configuration_string to attribute group
This patch (as737b) does a very small cleanup of core/sysfs.c by adding
the configuration_string attribute file to the existing attribute group
instead of treating it separately. It doesn't need this separate
treatment because unlike the other device string attributes, it changes
along with the active configuration.
The patch also fixes a simple typo (which, oddly enough, doesn't seem to
bother the compiler).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dmitry Torokhov [Wed, 2 Aug 2006 02:33:34 +0000 (22:33 -0400)]
USB: Make usb_buffer_free() NULL-safe
kfree() handles NULL arguments which is handy in error handling paths as one
does need to insert bunch of ifs. How about making usb_buffer_free() do the
same?
Werner Lemberg [Tue, 18 Jul 2006 15:00:52 +0000 (17:00 +0200)]
USB: ark3116: Add TIOCGSERIAL and TIOCSSERIAL ioctl calls.
Add (dummy?) support for TIOCGSERIAL and TIOCSSERIAL ioctl calls to the USB
serial driver file `ark3116.c'. This is sufficient for me to run wvdial
successfully, receive my email, and do webbrowsing with firefox. On the
other hand, running the cvs program to update archives seems not to work,
and the traceroute command sometimes says
send failed: No buffer space available
Looks like a buffering problem... My knowledge of serial device drivers is
zero, so I can't fix this -- I just did a cut'n'paste from other USB serial
drivers...
Signed-off-by: Werner Lemberg <wl@gnu.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Thu, 29 Jun 2006 19:25:39 +0000 (12:25 -0700)]
USB: pxa2xx_udc understands GPIO based VBUS sensing
This updates the PXA 25x UDC board-independent infrastructure for VBUS sensing
and the D+ pullup. The original code evolved from rather bizarre support on
Intel's "Lubbock" reference hardware, so that on more sensible hardware it
doesn't work as well as it could/should.
The change is just to teach the UDC driver how to use built-in PXA GPIO pins
directly. This reduces the amount of board-specfic object code needed, and
enables the use of a VBUS sensing IRQ on boards (like Gumstix) that have one.
With VBUS sensing, the UDC is unclocked until a host is actually connected.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vitaly Wool [Thu, 29 Jun 2006 14:28:18 +0000 (18:28 +0400)]
USB OHCI controller support for PNX4008
inlined is the patch that adds basic support for USB OHCI controller
support for PNX4008 Philips PNX4008 ARM board. Due to HW design, it
depends on I2C driver for PNX4008 which I've recetnly posted to LKML and
i2c at lm-sensors.
Ben Dooks [Mon, 26 Jun 2006 22:36:07 +0000 (23:36 +0100)]
USB: ohci-s3c2410.c: clock now usb-bus-host
With the newer Samsung S3C2412 and S3C2413 SoC devices,
the 48MHz USB clock has been given an individual gate
into the USB OHCI and gadget blocks.
This clock is called usb-bus-clock, and we need to
replace the old use of the USB PLL (upll) directly
with the new usb-bus-host.
The S3C2410 clock driver has been updated already to
provide a virtual clock which is a child of the UPLL
to maintain compatibility. The S3C2412 clock driver
correctly enables the PLL when either usb-bus clock
is active.
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell [Fri, 4 Aug 2006 18:31:55 +0000 (11:31 -0700)]
USB: OHCI avoids root hub timer polling
This teaches OHCI to use the root hub status change (RHSC) IRQ, bypassing
root hub timers most of the time and switching over to the "new" root hub
polling scheme. It's complicated by the fact that implementations of OHCI
trigger and ack that IRQ differently (the spec is vague there).
Avoiding root hub timers helps mechanisms like "dynamic tick" leave the
CPU in lowpower modes for longer intervals.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Thu, 14 Sep 2006 19:18:54 +0000 (15:18 -0400)]
USB: unusual_devs entry for Lacie DVD+-RW
This patch (as781) adds an entry to unusual_devs.h for the Lacie DVD+-RW
drive. Apparently its USB interface has requirements similar to the
Genesys Logic interface; it doesn't like data to be sent too soon after
a command.
This fixes Bugzilla #6817.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Phil Dibowitz <phil@ipom.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] minor reformatting to vmlinux.lds.S
[IA64] CMC/CPE: Reverse the order of fetching log and checking poll threshold
[IA64] PAL calls need physical mode, stacked
[IA64] ar.fpsr not set on MCA/INIT kernel entry
[IA64] printing support for MCA/INIT
[IA64] trim output of show_mem()
[IA64] show_mem() printk levels
[IA64] Make gp value point to Region 5 in mca handler
Revert "[IA64] Unwire set/get_robust_list"
[IA64] Implement futex primitives
[IA64-SGI] Do not request DMA memory for BTE
[IA64] Move perfmon tables from thread_struct to pfm_context
[IA64] Add interface so modules can discover whether multithreading is on.
[IA64] kprobes: fixup the pagefault exception caused by probehandlers
[IA64] kprobe opcode 16 bytes alignment on IA64
[IA64] esi-support
[IA64] Add "model name" to /proc/cpuinfo
Andrew Morton [Wed, 27 Sep 2006 08:51:15 +0000 (01:51 -0700)]
[PATCH] x86: use probe_kernel_address in handle_BUG()
Avoid possible deadlock on a BUG() inside down_write(mmap_sem). The deadlock
can only occur if something has gone horridly wrong, because a fault here
shouldn't happen.
Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ingo Oeser pointed out that because current expands to an inline function
it is more space efficient and somewhat faster to simply keep a cached copy
of current in another variable. This patch implements that for the
de_thread function.
(akpm: saves nearly 100 bytes of text on x86)
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] pid: remove temporary debug code in attach_pid
With the patches flying between Oleg and myself somehow this temporary
debug code got left in pid.c. It was never intended to make it to the
stable kernel.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Oleg Nesterov <oleg@tv-sign.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] pid: Implement transfer_pid and use it to simplify de_thread
In de_thread we move pids from one process to another, a rather ugly case.
The function transfer_pid makes it clear what we are doing, and makes the
action atomic. This is useful we ever want to atomically traverse the
process group and session lists, in a rcu safe manner.
Even if the atomic properties this change should be a win as transfer_pid
should be less code to execute than executing both attach_pid and
detach_pid, and this should make de_thread slightly smaller as only a
single function call needs to be emitted. The only downside is that the
code might be slower to execute as the odds are against transfer_pid being
in cache.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Oleg Nesterov <oleg@tv-sign.ru> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] sysctl: Document that sys_sysctl will be removed
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] sysctl: Allow /proc/sys without sys_sysctl
Since sys_sysctl is deprecated start allow it to be compiled out. This
should catch any remaining user space code that cares, and paves the way
for further sysctl cleanups.
[akpm@osdl.org: If sys_sysctl() is not compiled-in, emit a warning] Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] Include __param section in read-only data range
The param section is an array of "kernel_param" structures, storing only
constant data: pointer to name, permission of the variable pointed to by
(void *)arg and pointers to set/get methods.
Move end_rodata down to include __param section in the read-only range used
by CONFIG_DEBUG_RODATA.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org> Acked-by: Arjan van de Ven <arjan@infradead.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Michael Tokarev [Wed, 27 Sep 2006 08:50:56 +0000 (01:50 -0700)]
[PATCH] EISA bus MODALIAS attributes support
Add modalias attribute support for the almost forgotten now EISA bus and
(at least some) EISA-aware modules.
The modalias entry looks like (for an 3c509 NIC):
eisa:sTCM5093
and the in-module alias like:
eisa:sTCM5093*
The patch moves struct eisa_device_id declaration from include/linux/eisa.h
to include/linux/mod_devicetable.h (so that the former now #includes the
latter), adds proper MODULE_DEVICE_TABLE(eisa, ...) statements for all
drivers with EISA IDs I found (some drivers already have that DEVICE_TABLE
declared), and adds recognision of __mod_eisa_device_table to
scripts/mod/file2alias.c so that proper modules.alias will be generated.
There's no support for /lib/modules/$kver/modules.eisamap, as it's not used
by any existing tools, and because with in-kernel modalias mechanism those
maps are obsolete anyway.
The rationale for this patch is:
a) to make EISA bus to act as other busses with modalias
support, to unify driver loading
b) to foget about EISA finally - with this patch, kernel
(who still supports EISA) will be the only one who knows
how to choose the necessary drivers for this bus ;)
[akpm@osdl.org: fix the kbuild bit] Signed-off-by: Michael Tokarev <mjt@tls.msk.ru> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Randy Dunlap <rdunlap@xenotime.net> Acked-the-net-bits-by: Jeff Garzik <jeff@garzik.org> Acked-the-tulip-bit-by: Valerie Henson <val_henson@linux.intel.com> Cc: James Bottomley <James.Bottomley@steeleye.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Shaohua Li [Wed, 27 Sep 2006 08:50:54 +0000 (01:50 -0700)]
[PATCH] x86 microcode: don't check the size
IA32 manual says if micorcode update's size is 0, then the size is
default size (2048 bytes). But this doesn't suggest all microcode
update's size should be above 2048 bytes to me. We actually had a
microcode update whose size is 1024 bytes. The patch just removed the
check.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Cc: Tigran Aivazian <tigran@veritas.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Shaohua Li [Wed, 27 Sep 2006 08:50:53 +0000 (01:50 -0700)]
[PATCH] x86 microcode: add sysfs and hotplug support
Add sysfs support. Currently each CPU has three microcode related
attributes. One is 'version' which shows current ucode version of CPU.
Tools can use the attribute do validation or show CPU ucode status. one is
'reload' which allows manually reloading ucode. Another is
'processor_flags', which exports processor flags, so we can write tools to
check if CPU has latest ucode. Also add suspend/resume and CPU hotplug
support.
Shaohua Li [Wed, 27 Sep 2006 08:50:52 +0000 (01:50 -0700)]
[PATCH] x86 microcode: using request_firmware to pull microcode
Using request_firmware to pull ucode from userspace, so we don't need the
application 'microcode_ctl' to assist. We name each ucode file according
to CPU's info as intel-ucode/family-model-stepping. In this way we could
split ucode file as small one. This has a lot of advantages such as
selectively update and validate microcode for specific models, better
manage microcode file, easily write tools for administerators and so on.
with the changes, we should put all intel-ucode/xx-xx-xx microcode files
into the firmware dir (I had a tool to split previous big data file into
small one and later we will release new style data file). The init script
should be changed to just loading the driver without unloading
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Acked-by: Tigran Aivazian <tigran@veritas.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adrian Bunk [Wed, 27 Sep 2006 08:50:50 +0000 (01:50 -0700)]
[PATCH] reiserfs: warn about the useless nolargeio option
Since the nolargeio option no longer has any effect, print a warning
instead of setting a write-only variable.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Cc: Jeff Mahoney <jeffm@suse.com> Cc: Chris Mason <mason@suse.com> Cc: Hans Reiser <reiser@namesys.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] inode-diet: Eliminate i_blksize from the inode structure
This eliminates the i_blksize field from struct inode. Filesystems that want
to provide a per-inode st_blksize can do so by providing their own getattr
routine instead of using the generic_fillattr() function.
Note that some filesystems were providing pretty much random (and incorrect)
values for i_blksize.
[PATCH] inode_diet: Replace inode.u.generic_ip with inode.i_private
The following patches reduce the size of the VFS inode structure by 28 bytes
on a UP x86. (It would be more on an x86_64 system). This is a 10% reduction
in the inode size on a UP kernel that is configured in a production mode
(i.e., with no spinlock or other debugging functions enabled; if you want to
save memory taken up by in-core inodes, the first thing you should do is
disable the debugging options; they are responsible for a huge amount of bloat
in the VFS inode structure).
This patch:
The filesystem or device-specific pointer in the inode is inside a union,
which is pretty pointless given that all 30+ users of this field have been
using the void pointer. Get rid of the union and rename it to i_private, with
a comment to explain who is allowed to use the void pointer. This is just a
cleanup, but it allows us to reuse the union 'u' for something something where
the union will actually be used.
[PATCH] kdump: introduce "reset_devices" command line option
Resetting the devices during driver initialization can be a costly
operation in terms of time (especially scsi devices). This option can be
used by drivers to know that user forcibly wants the devices to be reset
during initialization.
This option can be useful while kernel is booting in unreliable
environment. For ex. during kdump boot where devices are in unknown
random state and BIOS execution has been skipped.
Ian Kent [Wed, 27 Sep 2006 08:50:44 +0000 (01:50 -0700)]
[PATCH] autofs4 needs to force fail return revalidate
For a long time now I have had a problem with not being able to return a
lookup failure on an existsing directory. In autofs this corresponds to a
mount failure on a autofs managed mount entry that is browsable (and so the
mount point directory exists).
While this problem has been present for a long time I've avoided resolving
it because it was not very visible. But now that autofs v5 has "mount and
expire on demand" of nested multiple mounts, such as is found when mounting
an export list from a server, solving the problem cannot be avoided any
longer.
I've tried very hard to find a way to do this entirely within the autofs4
module but have not been able to find a satisfactory way to achieve it.
So, I need to propose a change to the VFS.
Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6 / log