Ben Dooks [Sat, 13 Sep 2008 09:33:24 +0000 (02:33 -0700)]
spi_s3c24xx: fix section warning
Fix the section mismatch warning generated by the incorrect naming of
s3c24xx_spidrv which should be s3c24xx_spi_driver:
WARNING: drivers/spi/spi_s3c24xx.o(.data+0x4):
Section mismatch in reference from the variable s3c24xx_spidrv
to the (unknown reference) .exit.text:(unknown)
Signed-off-by: Ben Dooks <ben-linux@fluff.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atmel_lcdfb: disable LCD and DMA engines when suspending
When suspending the system with atmel_lcdfb enabled, I sometimes see
this:
atmel_lcdfb atmel_lcdfb.0: FIFO underflow 0x10
Which can be explained by the fact that we're not stopping the LCD
controller and its DMA engine when suspending, we're just gating the
clocks to them.
There's another potential issue which may be harder to trigger but
much more nasty: If we gate the clocks at _just_ the right moment,
e.g. when the DMA engine is doing a bus transaction, we may cause the
DMA engine to violate the system bus protocol and cause a lockup.
Avoid these issues by shutting down the LCD controller before entering
suspend (and restarting it when resuming). This prevents the underrun
from happening in the first place, and prevents whatever nastiness is
happening when the bus clock stops in the middle of a DMA transfer.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Robin Holt [Sat, 13 Sep 2008 09:33:22 +0000 (02:33 -0700)]
ia64: fix panic during `modprobe -r xpc'
If you are on ia64 and you modprobe xpc then modprobe -r xpc, you
immediately get a panic. xpc depends on xp which depends on gru for a
symbol. That symbol is only used when we are running on UV hardware.
Currently, the GRU driver detects we are not on UV hardware and does no
initializing. It does not do the same check when unloading. As a result,
the gru driver attempts to tear down stuff that was not setup.
This is a simple two-line workaround to get us through this release. Once
2.6.28 is opened, we need to rework the symbols that xp is depending on
from gru so the gru driver can properly fail to load when hardware is not
available.
Signed-off-by: Robin Holt <holt@sgi.com> Cc: "Luck, Tony" <tony.luck@intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mm: mark the correct zone as full when scanning zonelists
The iterator for_each_zone_zonelist() uses a struct zoneref *z cursor when
scanning zonelists to keep track of where in the zonelist it is. The
zoneref that is returned corresponds to the the next zone that is to be
scanned, not the current one. It was intended to be treated as an opaque
list.
When the page allocator is scanning a zonelist, it marks elements in the
zonelist corresponding to zones that are temporarily full. As the
zonelist is being updated, it uses the cursor here;
if (NUMA_BUILD)
zlc_mark_zone_full(zonelist, z);
This is intended to prevent rescanning in the near future but the zoneref
cursor does not correspond to the zone that has been found to be full.
This is an easy misunderstanding to make so this patch corrects the
problem by changing zoneref cursor to be the current zone being scanned
instead of the next one.
Ned Forrester [Sat, 13 Sep 2008 09:33:18 +0000 (02:33 -0700)]
pxa2xx_spi: dma bugfixes
Fixes two DMA bugs in the pxa2xx_spi driver. The first bug is in all
versions of this driver; the second was introduced in the 2.6.20 kernel,
and prevents using the driver with chips like m25p16 flash (which can
issue large DMA reads).
1. Zero length transfers are permitted for use to insert timing,
but pxa2xx_spi.c will fail if this is requested in DMA mode.
Fixed by using programmed I/O (PIO) mode for such transfers.
2. Transfers larger than 8191 are not permitted in DMA mode. A
test for length rejects all large transfers regardless of DMA
or PIO mode. Worked around by rejecting only large transfers
with DMA mapped buffers, and forcing all other transfers
larger than 8191 to use PIO mode. A rate limited warning is
issued for DMA transfers forced to PIO mode.
This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20. An additional patch would be
required for older kernels, but those versions are very buggy anyway.
Signed-off-by: Ned Forrester <nforrester@whoi.edu> Cc: Vernon Sauder <vernoninhand@gmail.com> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ned Forrester [Sat, 13 Sep 2008 09:33:17 +0000 (02:33 -0700)]
pxa2xx_spi: chipselect bugfixes
Fixes several chipselect bugs in the pxa2xx_spi driver. These bugs are in
all versions of this driver and prevent using it with chips like m25p16
flash.
1. The spi_transfer.cs_change flag is handled too early:
before spi_transfer.delay_usecs applies, thus making the
delay ineffective at holding chip select.
2. spi_transfer.delay_usecs is ignored on the last transfer
of a message (likewise not holding chipselect long enough).
3. If spi_transfer.cs_change is set on the last transfer, the
chip select is always disabled, instead of the intended
meaning: optionally holding chip select enabled for the
next message.
Those first three bugs were fixed with a relocation of delays
and chip select de-assertions.
4. If a message has the cs_change flag set on the last transfer,
and had the chip select stayed enabled as requested (see 3,
above), it would not have been disabled if the next message is
for a different chip. Fixed by dropping chip select regardless
of cs_change at end of a message, if there is no next message
or if the next message is for a different chip.
This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20. An additional patch would be
required for older kernels, but those versions are very buggy anyway.
Signed-off-by: Ned Forrester <nforrester@whoi.edu> Cc: Vernon Sauder <vernoninhand@gmail.com> Cc: Eric Miao <eric.y.miao@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Peter Korsgaard [Sat, 13 Sep 2008 09:33:14 +0000 (02:33 -0700)]
spi_mpc83xx: fix clockrate calculation for low speed
Commit a61f5345 (spi_mpc83xx clockrate fixes) broke clockrate calculation
for low speeds. SPMODE_DIV16 should be set if the divider is higher than
64, not only if the divider gets clipped to 1024.
Furthermore, the clipping check was off by a factor 16 as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A "Quicklists: 0 kB" line has just started appearing in
/proc/meminfo, but most architectures (including x86) don't have
them configured, so #ifdef it, like the highmem lines.
And those architectures which do have quicklists configured are
using them for page tables: so let's place it next to PageTables.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Acked-by: Christoph Lameter <cl@linux-foundation.org> Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Sesterhenn [Sat, 13 Sep 2008 09:33:12 +0000 (02:33 -0700)]
bfs: fix Lockdep warning
This fixes:
=============================================
[ INFO: possible recursive locking detected ] 2.6.27-rc5-00283-g70bb089 #68
---------------------------------------------
touch/6855 is trying to acquire lock:
(&info->bfs_lock){--..}, at: [<c02262f5>] bfs_delete_inode+0x9e/0x18c
but task is already holding lock:
(&info->bfs_lock){--..}, at: [<c0226c00>] bfs_create+0x45/0x187
other info that might help us debug this:
2 locks held by touch/6855:
#0: (&type->i_mutex_dir_key#5){--..}, at: [<c018ad13>] do_filp_open+0x10b/0x62f
#1: (&info->bfs_lock){--..}, at: [<c0226c00>] bfs_create+0x45/0x187
Li Zefan [Sat, 13 Sep 2008 09:33:09 +0000 (02:33 -0700)]
cpuset: hotplug documentation fix
If all the cpus in a cpuset are offlined, the tasks in it will be moved to
the nearest ancestor with non-empty cpus.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Paul Jackson <pj@sgi.com> Cc: Paul Menage <menage@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpusets: restructure the function update_cpumask() and update_nodemask()
It might happen that 'echo 0 > /cpuset/sub/cpus' returned failure but 'cpus'
has been changed, because cpus was changed before calling heap_init() which
may return -ENOMEM.
This patch restores the orginal behavior.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Acked-by: Paul Menage <menage@google.com> Cc: Paul Jackson <pj@sgi.com> Cc: Miao Xie <miaox@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
proc: more debugging for "already registered" case
Print parent directory name as well.
The aim is to catch non-creation of parent directory when proc_mkdir will
return NULL and all subsequent registrations go directly in /proc instead
of intended directory.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Fixed insane printk string while at it. - Linus ] Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 11 Sep 2008 16:18:56 +0000 (17:18 +0100)]
MN10300: Change the fault handler to check in_atomic() not in_interrupt()
Change the MN10300 fault handler to make it check in_atomic() rather than
in_interrupt() as commit 6edaf68a87d17570790fd55f0c451a29ec1d6703 did for other
architectures:
Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
Date: Wed Dec 6 20:32:18 2006 -0800
[PATCH] mm: arch do_page_fault() vs in_atomic()
In light of the recent pagefault and filemap_copy_from_user work I've
gone through all the arch pagefault handlers to make sure the
inc_preempt_count() 'feature' works as expected.
Several sections of code (including the new filemap_copy_from_user)
rely on the fact that faults do not take locks under increased preempt
count.
Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The callers of sg_copy_buffer must disable interrupts before calling
it (since it uses kmap_atomic). Some callers use it on
interrupt-disabled code but some need to take the trouble to disable
interrupts just for this. No wonder they forget about it and we hit a
bug like:
http://bugzilla.kernel.org/show_bug.cgi?id=11529
James said that it might be better to disable interrupts inside the
function rather than risk the callers getting it wrong.
Merge branch 'kvm-updates/2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm
* 'kvm-updates/2.6.27' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: VMX: Always return old for clear_flush_young() when using EPT
KVM: SVM: fix guest global tlb flushes with NPT
KVM: SVM: fix random segfaults with NPT enabled
block: disable sysfs parts of the disk command filter
We still have life time issues with the sysfs command filter kobject,
so disable it for 2.6.27 release. We can revisit this and make it work
properly for 2.6.28, for 2.6.27 release it's too risky.
Accesses to CR4 are intercepted even with Nested Paging enabled. But the code
does not check if the guest wants to do a global TLB flush. So this flush gets
lost. This patch adds the check and the flush to svm_set_cr4.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Avi Kivity <avi@qumranet.com>
Joerg Roedel [Wed, 27 Aug 2008 12:18:43 +0000 (14:18 +0200)]
KVM: SVM: fix random segfaults with NPT enabled
This patch introduces a guest TLB flush on every NPF exit in KVM. This fixes
random segfaults and #UD exceptions in the guest seen under some workloads
(e.g. long running compile workloads or tbench). A kernbench run with and
without that fix showed that it has a slowdown lower than 0.5%
Cc: stable@kernel.org Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Avi Kivity <avi@qumranet.com>
commit 0d3244d6439c8c31d2a29efd587c7aca9042c8aa ("V4L/DVB (8342):
sh_mobile_ceu_camera: Add SuperH Mobile CEU driver V3") introduced
VIDEO_SH_MOBILE_CEU, which selects VIDEOBUF_DMA_CONTIG. This circumvents the
dependency on HAS_DMA of VIDEOBUF_DMA_CONTIG.
Add a dependency on HAS_DMA to VIDEO_SH_MOBILE_CEU to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Paul Mundt <lethal@linux-sh.org> Acked-by: Magnus Damm <damm@igel.co.jp> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
swiotlb: fix back-off path when memory allocation fails
This fixes a SWIOTLB oops
With SWIOTLB being enabled and straight-forward page allocation
failure [1], the swiotlb_alloc_coherent fall-back path hits an
issue [2], resulting in my webcam failing to work.
At the time of oops, RDI is clearly a pointer to a structure which
has arrived as NULL, leading to the typo in swiotlb_map_single's
callsite arguments.
Correctly passing the device structure [3] addresses the issue and
gets my webcam working again (the allocation failure still occuring).
ide: Fix pointer arithmetic in hpt3xx driver code (3rd try)
git commit 74811f355f4f69a187fa74892dcf2a684b84ce99 causes crash at
module load (or boot) time on my machine with a hpt374 controller.
The reason for this is that for initializing second controller which sets
(hwif->dev == host->dev[1]) to true (1), adds 1 to a void ptr, which
advances it by one byte instead of advancing it by sizeof(hpt_info) bytes.
Because of this, all initialization functions get corrupted data in info
variable which causes a crash at boot time.
This patch fixes that and makes my machine boot again.
The card itself is a HPT374 raid conroller: Here is the lspci -v output:
03:06.0 RAID bus controller: HighPoint Technologies, Inc. HPT374 (rev
07)
Subsystem: HighPoint Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 28
I/O ports at 8000 [size=8]
I/O ports at 7800 [size=4]
I/O ports at 7400 [size=8]
I/O ports at 7000 [size=4]
I/O ports at 6800 [size=256]
Expansion ROM at fe8e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
03:06.1 RAID bus controller: HighPoint Technologies, Inc. HPT374 (rev
07)
Subsystem: HighPoint Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 28
I/O ports at 9800 [size=8]
I/O ports at 9400 [size=4]
I/O ports at 9000 [size=8]
I/O ports at 8800 [size=4]
I/O ports at 8400 [size=256]
Capabilities: [60] Power Management version 2
Signed-off-by: Masoud Sharbiani <masouds@google.com> Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com> Cc: Andrew Morton <akpm@linux-foundation.org>
[bart: use dev_get_drvdata() per Sergei's suggestion] Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Paul E. McKenney [Sun, 31 Aug 2008 18:06:30 +0000 (11:06 -0700)]
[IA64] prevent ia64 from invoking irq handlers on offline CPUs
Make ia64 refrain from clearing a given to-be-offlined CPU's bit in the
cpu_online_mask until it has processed pending irqs. This change
prevents other CPUs from being blindsided by an apparently offline CPU
nevertheless changing globally visible state. Also remove the existing
redundant cpu_clear(cpu, cpu_online_map).
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Robin Holt [Tue, 9 Sep 2008 15:34:44 +0000 (10:34 -0500)]
[IA64] fix up bte.h
bte.h expects a #define of L1_CACHE_MASK which is currently only
in bte.c. This small patch gets bte.h to include cleanly and makes
BTE_UNALIGNED_COPY not report errors.
Signed-off-by: Robin Holt <holt@sgi.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
James Bottomley [Tue, 9 Sep 2008 22:56:47 +0000 (17:56 -0500)]
[IA64] fix compile failure with non modular builds
Broke the non modular builds by moving an essential function into
modules.c. Fix this by moving it out again and into asm/sections.h as
an inline. To do this, the definitions of struct fdesc and struct
got_val have been lifted out of modules.c and put in asm/elf.h where
they belong.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Tao Ma [Tue, 2 Sep 2008 17:57:14 +0000 (01:57 +0800)]
ocfs2: Fix a bug in direct IO read.
ocfs2 will become read-only if we try to read the bytes which pass
the end of i_size. This can be easily reproduced by following steps:
1. mkfs a ocfs2 volume with bs=4k cs=4k and nosparse.
2. create a small file(say less than 100 bytes) and we will create the file
which is allocated 1 cluster.
3. read 8196 bytes from the kernel using O_DIRECT which exceeds the limit.
4. The ocfs2 volume becomes read-only and dmesg shows:
OCFS2: ERROR (device sda13): ocfs2_direct_IO_get_blocks:
Inode 66010 has a hole at block 1
File system is now read-only due to the potential of on-disk corruption.
Please run fsck.ocfs2 once the file system is unmounted.
So suppress the ERROR message.
Signed-off-by: Tao Ma <tao.ma@oracle.com> Signed-off-by: Mark Fasheh <mfasheh@suse.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ipv6: Fix OOPS in ip6_dst_lookup_tail().
ipsec: Restore larval states and socket policies in dump
[Bluetooth] Reject L2CAP connections on an insecure ACL link
[Bluetooth] Enforce correct authentication requirements
[Bluetooth] Fix reference counting during ACL config stage
Neil Horman [Tue, 9 Sep 2008 20:51:35 +0000 (13:51 -0700)]
ipv6: Fix OOPS in ip6_dst_lookup_tail().
This fixes kernel bugzilla 11469: "TUN with 1024 neighbours:
ip6_dst_lookup_tail NULL crash"
dst->neighbour is not necessarily hooked up at this point
in the processing path, so blindly dereferencing it is
the wrong thing to do. This NULL check exists in other
similar paths and this case was just an oversight.
Also fix the completely wrong and confusing indentation
here while we're at it.
Based upon a patch by Evgeniy Polyakov.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Merge branch 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevents: remove WARN_ON which was used to gather information
Thomas Gleixner [Tue, 9 Sep 2008 19:38:57 +0000 (21:38 +0200)]
clockevents: remove WARN_ON which was used to gather information
The issue of the endless reprogramming loop due to a too small
min_delta_ns was fixed with the previous updates of the clock events
code, but we had no information about the spread of this problem. I
added a WARN_ON to get automated information via kerneloops.org and to
get some direct reports, which allowed me to analyse the affected
machines.
The WARN_ON has served its purpose and would be annoying for a release
kernel. Remove it and just keep the information about the increase of
the min_delta_ns value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is happening because of an improper usage of strcmp() in the
e820 parsing code. The strcmp() always returns !0 and never resets the
value for e820.nr_map and returns an incorrect user-defined map.
Merge branch 'linux-next' of git://git.infradead.org/~dedekind/ubifs-2.6
* 'linux-next' of git://git.infradead.org/~dedekind/ubifs-2.6:
UBIFS: make minimum fanout 3
UBIFS: fix division by zero
UBIFS: amend f_fsid
UBIFS: fill f_fsid
UBIFS: improve statfs reporting even more
UBIFS: introduce LEB overhead
UBIFS: add forgotten gc_idx_lebs component
UBIFS: fix assertion
UBIFS: improve statfs reporting
UBIFS: remove incorrect index space check
UBIFS: push empty flash hack down
UBIFS: do not update min_idx_lebs in stafs
UBIFS: allow for racing between GC and TNC
UBIFS: always read hashed-key nodes under TNC mutex
UBIFS: fix zero-length truncations
James Bottomley [Thu, 4 Sep 2008 01:43:36 +0000 (20:43 -0500)]
lib: Correct printk %pF to work on all architectures
It was introduced by "vsprintf: add support for '%pS' and '%pF' pointer
formats" in commit 0fe1ef24f7bd0020f29ffe287dfdb9ead33ca0b2. However,
the current way its coded doesn't work on parisc64. For two reasons: 1)
parisc isn't in the #ifdef and 2) parisc has a different format for
function descriptors
Make dereference_function_descriptor() more accommodating by allowing
architecture overrides. I put the three overrides (for parisc64, ppc64
and ia64) in arch/kernel/module.c because that's where the kernel
internal linker which knows how to deal with function descriptors sits.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Tony Luck <tony.luck@intel.com> Acked-by: Kyle McMartin <kyle@mcmartin.ca> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris Snook [Tue, 9 Sep 2008 07:26:57 +0000 (03:26 -0400)]
MAINTAINERS: add Atheros maintainer for atlx
Jie Yang at Atheros is getting more directly involved with upstream work
on the atl* drivers. This patch changes the ATL1 entry to ATLX (atl2
support posted to netdev today) and adds him as a maintainer.
update Documentation/filesystems/Locking for 2.6.27 changes
In the 2.6.27 circle ->fasync lost the BKL, and the last remaining
->open variant that takes the BKL is also gone. ->get_sb and ->kill_sb
didn't have BKL forever, so updated the entries while we're at that.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Herbert Xu [Tue, 9 Sep 2008 12:23:37 +0000 (05:23 -0700)]
ipsec: Restore larval states and socket policies in dump
The commit commit 4c563f7669c10a12354b72b518c2287ffc6ebfb3 ("[XFRM]:
Speed up xfrm_policy and xfrm_state walking") inadvertently removed
larval states and socket policies from netlink dumps. This patch
restores them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
[S390] cio: allow offline processing for disconnected devices
When disconnected ccw devices are removed, the device has to be set
offline, otherwise there will be side effects including a reference
count imbalance. This patch modifies ccw_device_offline to work for
devices in disconnecte/not operational state. ccw_device_offline is
called by cio for devices which are online during device removal.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
ssch() has two classes of return codes:
- condition codes (0-3) which need to be translated to Linux
error codes
- Linux error codes (-EIO on exceptions) which should be passed
to the caller (instead of erronously being handled like
condition code 3)
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jarod Wilson [Tue, 9 Sep 2008 10:38:56 +0000 (12:38 +0200)]
[S390] CVE-2008-1514: prevent ptrace padding area read/write in 31-bit mode
When running a 31-bit ptrace, on either an s390 or s390x kernel,
reads and writes into a padding area in struct user_regs_struct32
will result in a kernel panic.
This is also known as CVE-2008-1514.
Test case available here:
http://sources.redhat.com/cgi-bin/cvsweb.cgi/~checkout~/tests/ptrace-tests/tests/user-area-padding.c?cvsroot=systemtap
Steps to reproduce:
1) wget the above
2) gcc -o user-area-padding-31bit user-area-padding.c -Wall -ggdb2 -D_GNU_SOURCE -m31
3) ./user-area-padding-31bit
<panic>
Test status
-----------
Without patch, both s390 and s390x kernels panic. With patch, the test case,
as well as the gdb testsuite, pass without incident, padding area reads
returning zero, writes ignored.
Nb: original version returned -EINVAL on write attempts, which broke the
gdb test and made the test case slightly unhappy, Jan Kratochvil suggested
the change to return 0 on write attempts.
Signed-off-by: Jarod Wilson <jarod@redhat.com> Tested-by: Jan Kratochvil <jan.kratochvil@redhat.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[Bluetooth] Reject L2CAP connections on an insecure ACL link
The Security Mode 4 of the Bluetooth 2.1 specification has strict
authentication and encryption requirements. It is the initiators job
to create a secure ACL link. However in case of malicious devices, the
acceptor has to make sure that the ACL is encrypted before allowing
any kind of L2CAP connection. The only exception here is the PSM 1 for
the service discovery protocol, because that is allowed to run on an
insecure ACL link.
Previously it was enough to reject a L2CAP connection during the
connection setup phase, but with Bluetooth 2.1 it is forbidden to
do any L2CAP protocol exchange on an insecure link (except SDP).
The new hci_conn_check_link_mode() function can be used to check the
integrity of an ACL link. This functions also takes care of the cases
where Security Mode 4 is disabled or one of the devices is based on
an older specification.
With the introduction of Security Mode 4 and Simple Pairing from the
Bluetooth 2.1 specification it became mandatory that the initiator
requires authentication and encryption before any L2CAP channel can
be established. The only exception here is PSM 1 for the service
discovery protocol (SDP). It is meant to be used without any encryption
since it contains only public information. This is how Bluetooth 2.0
and before handle connections on PSM 1.
For Bluetooth 2.1 devices the pairing procedure differentiates between
no bonding, general bonding and dedicated bonding. The L2CAP layer
wrongly uses always general bonding when creating new connections, but it
should not do this for SDP connections. In this case the authentication
requirement should be no bonding and the just-works model should be used,
but in case of non-SDP connection it is required to use general bonding.
If the new connection requires man-in-the-middle (MITM) protection, it
also first wrongly creates an unauthenticated link key and then later on
requests an upgrade to an authenticated link key to provide full MITM
protection. With Simple Pairing the link key generation is an expensive
operation (compared to Bluetooth 2.0 and before) and doing this twice
during a connection setup causes a noticeable delay when establishing
a new connection. This should be avoided to not regress from the expected
Bluetooth 2.0 connection times. The authentication requirements are known
up-front and so enforce them.
To fulfill these requirements the hci_connect() function has been extended
with an authentication requirement parameter that will be stored inside
the connection information and can be retrieved by userspace at any
time. This allows the correct IO capabilities exchange and results in
the expected behavior.
[Bluetooth] Fix reference counting during ACL config stage
The ACL config stage keeps holding a reference count on incoming
connections when requesting the extended features. This results in
keeping an ACL link up without any users. The problem here is that
the Bluetooth specification doesn't define an ownership of the ACL
link and thus it can happen that the implementation on the initiator
side doesn't care about disconnecting unused links. In this case the
acceptor needs to take care of this.
Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: pm_standby low-power ram bug fix
avr32: Fix lockup after Java stack underflow in user mode
Merge branch 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix rare boot build breakage
powerpc/spufs: Fix possible scheduling of a context to multiple SPEs
powerpc/spufs: Fix race for a free SPU
powerpc/spufs: Fix multiple get_spu_context()
Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: arch_reinit_sched_domains() must destroy domains to force rebuild
sched, cpuset: rework sched domains and CPU hotplug handling (v4)
Merge branch 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ahci: RAID mode SATA patch for Intel Ibex Peak DeviceIDs
pata_sil680: remove duplicate pcim_enable_device
libata-sff: kill spurious WARN_ON() in ata_hsm_move()
sata_nv: disable hardreset for generic
ahci: disable PMP for marvell ahcis
sata_mv: add RocketRaid 1720 PCI ID to driver
ahci, pata_marvell: play nicely together
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
bridge: don't allow setting hello time to zero
netns : fix kernel panic in timewait socket destruction
pkt_sched: Fix qdisc state in net_tx_action()
netfilter: nf_conntrack_irc: make sure string is terminated before calling simple_strtoul
netfilter: nf_conntrack_gre: nf_ct_gre_keymap_flush() fixlet
netfilter: nf_conntrack_gre: more locking around keymap list
netfilter: nf_conntrack_sip: de-static helper pointers
Jason Wessel [Mon, 8 Sep 2008 13:53:37 +0000 (14:53 +0100)]
usb: fix null deferences in low level usb serial
The hw interface drivers for the usb serial devices deference the tty
structure to set up the parameters for the initial console. The tty
structure should be passed as a parameter to the set_termios() call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chuck Lever [Mon, 8 Sep 2008 15:58:13 +0000 (11:58 -0400)]
NFS: Restore missing hunk in NFS mount option parser
Automounter maps can contain mount options valid for other NFS
implementations but not for Linux. The Linux automounter uses the
mount command's "-s" command line option ("s" for "sloppy") so that
mount requests containing such options are not rejected.
Commit f45663ce5fb30f76a3414ab3ac69f4dd320e760a attempted to address a
known regression with text-based NFS mount option parsing. Unrecognized
mount options would cause mount requests to fail, even if the "-s"
option was used on the mount command line.
Unfortunately, this commit was not complete as submitted. It adds a
new mount option, "sloppy". But it is missing a hunk, so it now allows
NFS mounts with unrecognized mount options, even if the "sloppy" option
is not present. This could be a problem if a required critical mount
option such as "sync" is misspelled, for example, and is considered a
regression from 2.6.26.
This patch restores the missing hunk. Now, the default behavior of
text-based NFS mount options is as before: any unrecognized mount option
will cause the mount to fail.
Please include this in 2.6.27-rc.
Thanks to Neil Brown for reporting this.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Acked-by: J. Bruce Fields <bfields@citi.umich.edu> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
and the culprit cause seems to be starting the bridge interface.
In particular, when starting the bridge interface, his scripts
are specifying a hello timer interval of "0".
The bridge hello time can't be safely set to values less than 1
second, otherwise it is possible to end up with a runaway timer.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Mon, 8 Sep 2008 20:17:27 +0000 (13:17 -0700)]
netns : fix kernel panic in timewait socket destruction
How to reproduce ?
- create a network namespace
- use tcp protocol and get timewait socket
- exit the network namespace
- after a moment (when the timewait socket is destroyed), the kernel
panics.
This patch provides a function to purge all timewait sockets related
to a network namespace. The timewait sockets life cycle is not tied with
the network namespace, that means the timewait sockets stay alive while
the network namespace dies. The timewait sockets are for avoiding to
receive a duplicate packet from the network, if the network namespace is
freed, the network stack is removed, so no chance to receive any packets
from the outside world. Furthermore, having a pending destruction timer
on these sockets with a network namespace freed is not safe and will lead
to an oops if the timer callback which try to access data belonging to
the namespace like for example in:
inet_twdr_do_twkill_work
-> NET_INC_STATS_BH(twsk_net(tw), LINUX_MIB_TIMEWAITED);
Purging the timewait sockets at the network namespace destruction will:
1) speed up memory freeing for the namespace
2) fix kernel panic on asynchronous timewait destruction
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com> Acked-by: Denis V. Lunev <den@openvz.org> Acked-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit, at least the generic nops are fairly reasonable, but the
default nops for 64-bit really look pretty sad, and the P6 nops really do
look better.
So I would suggest perhaps moving the static P6 nop selection into the
CONFIG_X86_64 thing.
The alternative is to just get rid of that static nop selection, and just
have two cases: 32-bit and 64-bit, and just pick obviously safe cases for
them.
UDF currently doesn't set a llseek method for regular files, which
means it will fall back to default_llseek. This means no one can seek
beyond 2 Gigabytes on udf, and that there's not protection vs
the i_size updates from writers.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jan Kara <jack@suse.cz>
Tejun Heo [Fri, 29 Aug 2008 14:27:43 +0000 (16:27 +0200)]
libata-sff: kill spurious WARN_ON() in ata_hsm_move()
On HSM_ST_ERR, ata_hsm_move() triggers WARN_ON() if AC_ERR_DEV or
AC_ERR_HSM is not set. PHY events may trigger HSM_ST_ERR with other
error codes and, with or without it, there just isn't much reason to
do WARN_ON() on it. Even if error code is not set there, core EH
logic won't have any problem dealing with the error condition.
OSDL bz#11065 reports this problem.
Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tejun Heo [Fri, 29 Aug 2008 14:13:12 +0000 (16:13 +0200)]
sata_nv: disable hardreset for generic
of them being unifying probing, hotplug and EH reset paths uniform.
Previously, broken hardreset could go unnoticed as it wasn't used
during probing but when something goes wrong or after hotplug the
problem will surface and bite hard.
OSDL bug 11195 reports that sata_nv generic flavor falls into this
category. Hardreset itself succeeds but PHY stays offline after
hardreset. I tried longer debounce timing but the result was the
same.
http://bugzilla.kernel.org/show_bug.cgi?id=11195
So, it seems we'll have to drop hardreset from the generic flavor.
Alan Cox [Wed, 3 Sep 2008 13:48:34 +0000 (14:48 +0100)]
ahci, pata_marvell: play nicely together
I've been chasing Jeff about this for months. Jeff added the Marvell
device identifiers to the ahci driver without making the AHCI driver
handle the PATA port. This means a lot of users can't use current
kernels and in most distro cases can't even install.
This has been going on since March 2008 for the 6121 Marvell, and late 2007
for the 6145!!!
This was all pointed out at the time and repeatedly ignored. Bugs assigned
to Jeff about this are ignored also.
To quote Jeff in email
> "Just switch the order of 'ahci' and 'pata_marvell' in
> /etc/modprobe.conf, then use Fedora's tools regenerate the initrd.
> See? It's not rocket science, and the current configuration can be
> easily made to work for Fedora users."
(Which isn't trivial, isn't end user, shouldn't be needed, and as it usually
breaks at install time is in fact impossible)
To quote Jeff in August 2007
> " mv-ahci-pata
> Marvell 6121/6141 PATA support. Needs fixing in the 'PATA controller
> command' area before it is usable, and can go upstream."
Only he add the ids anyway later and caused regressions, adding a further
id in March causing more regresions.
The actual fix for the moment is very simple. If the user has included
the pata_marvell driver let it drive the ports. If they've only selected
for SATA support give them the AHCI driver which will run the port a fraction
faster. Allow the user to control this decision via ahci.marvell_enable as
a module parameter so that distributions can ship 'it works' defaults and
smarter users (or config tools) can then flip it over it desired.
Signed-off-by: Alan Cox <alan@redhat.com> Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A make -j20 powerpc kernel build broke a couple of months ago saying:
In file included from arch/powerpc/boot/gunzip_util.h:13,
from arch/powerpc/boot/prpmc2800.c:21:
arch/powerpc/boot/zlib.h:85: error: expected ‘:’, ‘,’, ‘;’, ‘}’ or ‘__attribute__’ before ‘*’ token
arch/powerpc/boot/zlib.h:630: warning: type defaults to ‘int’ in declaration of ‘Byte’
arch/powerpc/boot/zlib.h:630: error: expected ‘;’, ‘,’ or ‘)’ before ‘*’ token
It happened again yesterday: too rare for me to confirm the fix, but
it looks like the list of dependants on gunzip_util.h was incomplete.
Signed-off-by: Hugh Dickins <hugh@veritas.com> Signed-off-by: Paul Mackerras <paulus@samba.org>
Herbert Xu [Mon, 8 Sep 2008 04:29:54 +0000 (14:29 +1000)]
Revert "crypto: camellia - Use kernel-provided bitops, unaligned access helpers"
This reverts commit bd699f2df6dbc2f4cba528fe598bd63a4d3702c5,
which causes camellia to fail the included self-test vectors.
It has also been confirmed that it breaks existing encrypted
disks using camellia.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
net_tx_action() can skip __QDISC_STATE_SCHED bit clearing while qdisc
is neither ran nor rescheduled, which may cause endless loop in
dev_deactivate().
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb> Tested-by: Denys Fedoryshchenko <denys@visp.net.lb> Signed-off-by: Jarek Poplawski <jarkao2@gmail.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Mon, 8 Sep 2008 01:21:24 +0000 (18:21 -0700)]
netfilter: nf_conntrack_irc: make sure string is terminated before calling simple_strtoul
Alexey Dobriyan points out:
1. simple_strtoul() silently accepts all characters for given base even
if result won't fit into unsigned long. This is amazing stupidity in
itself, but
2. nf_conntrack_irc helper use simple_strtoul() for DCC request parsing.
Data first copied into 64KB buffer, so theoretically nothing prevents
reading past the end of it, since data comes from network given 1).
This is not actually a problem currently since we're guaranteed to have
a 0 byte in skb_shared_info or in the buffer the data is copied to, but
to make this more robust, make sure the string is actually terminated.
Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
It does "kfree(list_head)" which looks wrong because entity that was
allocated is definitely not list_head.
However, this all works because list_head is first item in
struct nf_ct_gre_keymap.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter: nf_conntrack_gre: more locking around keymap list
gre_keymap_list should be protected in all places.
(unless I'm misreading something)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Helper's ->help hook can run concurrently with itself, so iterating over
SIP helpers with static pointer won't work reliably.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
Andre Detsch [Thu, 4 Sep 2008 21:16:27 +0000 (21:16 +0000)]
powerpc/spufs: Fix possible scheduling of a context to multiple SPEs
We currently have a race when scheduling a context to a SPE -
after we have found a runnable context in spusched_tick, the same
context may have been scheduled by spu_activate().
This may result in a panic if we try to unschedule a context that has
been freed in the meantime.
This change exits spu_schedule() if the context has already been
scheduled, so we don't end up scheduling it twice.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com> Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: cpu_init(): fix memory leak when using CPU hotplug
x86: pda_init(): fix memory leak when using CPU hotplug
x86, xen: Use native_pte_flags instead of native_pte_val for .pte_flags
x86: move mtrr cpu cap setting early in early_init_xxxx
x86: delay early cpu initialization until cpuid is done
x86: use X86_FEATURE_NOPL in alternatives
x86: add NOPL as a synthetic CPU feature bit
x86: boot: stub out unimplemented CPU feature words
projects / linux-2.6 / log