Matthew Meno [Wed, 21 Jun 2006 19:25:53 +0000 (15:25 -0400)]
[PATCH] USB: Support for Susteen Datapilot Universal-2 cable in pl2303
The Susteen Datapilot cable
(http://www.susteen.com/productdetail/71/producthl/Notempty) has an
internal pl2303 to communicate with a set of dummy connector-ends that
connect to a variety of cell phones. I've found that it works right out
of the box by simply adding the product/vendor id to the pl2303 driver.
Signed-off-by: Matt Meno <mmeno@idealcorp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds basic Wireless USB 1.0 definitions to usb_ch9.h that
fit into the existing set of declarations. Boils down to two new
recipients for requests (ports and remote pipes), rpipe reset and
abort request codes and wire adapter and remote pipe descriptor
types.
Wire adapters are the USB <-> Wireless USB adaptors; remote pipes
are used by those adapters to pipe the host <-> endpoint traffic.
Pete Zaitcev [Wed, 21 Jun 2006 22:03:40 +0000 (15:03 -0700)]
[PATCH] USB: fix visor leaks
This patch fixes blatant leaks in visor driver and makes it report
mode sensible things in ->write_room (this is only needed if your visor
is a terminal though).
It is made to fit into 80 columns with a temporary variable.
Might even save a few instructions...
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pete Zaitcev [Wed, 21 Jun 2006 22:00:45 +0000 (15:00 -0700)]
[PATCH] USB: fix usb-serial leaks, oopses on disconnect
This fix addresses two issues:
- Unattached port structures were not freed
- My initial fix for crash when eventd runs a work in a freed port
did not go far enough
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Peter Moulder [Mon, 19 Jun 2006 12:47:49 +0000 (22:47 +1000)]
[PATCH] USB: Addition of vendor/product id pair for pl2303 driver
Text from the back of the box, for your information/amusement:
USB DATA CABLE
FOR K700 Series
The USB Cable is an ideal link between your mobile phone and PC. Employing
the user-friendiy [sic] USB standard,its capacity for rapid data transfer enables functions
such as synchronization of phone book and calendar,as well as Internet browsing via
a modem-enabled phone.Autual [sic] connection speed is dependent on phone capacity.
MADE IN CHINA
From: Peter Moulder <Peter.Moulder@infotech.monash.edu.au> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Daniel Mack [Fri, 23 Jun 2006 20:36:07 +0000 (21:36 +0100)]
[PATCH] USB: au1200: EHCI and OHCI fixes
I received an DBAU1200 eval kit from AMD a few days ago and tried to
enable the USB2 port, but the current linux-2.6 GIT did not even
compile with CONFIG_SOC_1200, CONFIG_SOC_AU1X00, CONFIG_USB_EHCI and
CONFIG_USB_OHCI set.
Furthermore, in ehci-hcd.c, platform_driver_register() was called with
an improper argument of type 'struct device_driver *' which of course
ended up in a kernel oops. How could that ever have worked on your
machines?
Anyway, here's a trivial patch that makes the USB subsystem working
on my board for both OHCI and EHCI.
It also removes the /* FIXME use "struct platform_driver" */.
Signed-off-by: Daniel Mack <daniel@caiaq.de> Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Acked-by: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Wed, 12 Jul 2006 14:05:41 +0000 (15:05 +0100)]
[PATCH] ide: fix Jmicron support
Prior to 2.6.18rc1 you could install with devices on a JMicron chipset
using the "all-generic-ide" option. As of this kernel the AHCI driver
grabs the controller and rams it into AHCI mode losing the PATA ports
and making CD drives and the like vanish. The all-generic-ide option
fails because the AHCI driver grabbed the PCI device and reconfigured
it.
To fix this three things are needed.
#1 We must put the chip into dual function mode
#2 The AHCI driver must grab only function 0 (already in your rc1 tree)
#3 Something must grab the PATA ports
The attached patch is the minimal risk edition of this. It puts the chip
into dual function mode so that AHCI will grab the SATA ports without
losing the PATA ports. To keep the risk as low as possible the third
patch adds the PCI identifiers for the PATA port and the FN check to the
ide-generic driver. There is a more featured jmicron driver on its way
but that adds risk and the ide-generic support is sufficient to install
and run a system.
The actual chip setup done by the quirk is the precise setup recommended
by the vendor.
(The JMB368 appears only in the ide-generic entry as it has no AHCI so
does not need the quirk)
Signed-off-by: Alan Cox <alan@redhat.com> Acked-by: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] Make cpu_relax() imply barrier() on all arches
During the recent discussion of taking 'volatile' off of the spinlock, I
noticed that while most arches #define cpu_relax() such that it implies
barrier(), some arches define cpu_relax() to be empty.
This patch changes the definition of cpu_relax() for frv, h8300, m68knommu,
sh, sh64, v850 and xtensa from an empty while(0) to the compiler barrier().
Signed-off-by: Chase Venters <chase.venters@clientec.com> Acked-by: Arjan van de Ven <arjan@Linux.intel.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
the call of rtc_get_rtc_time() is highly suspect. At a minimum we
need the patch below to save/restore hardirq state.
Signed-off-by: Ingo Molnar <mingo@elte.hu> Cc: Joseph Fannin <jfannin@gmail.com> Cc: John Stultz <johnstul@us.ibm.com> Cc: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] msi: Only keep one msi_desc in each slab entry.
It looks like someone confused kmem_cache_create with a different allocator
and was attempting to give it knowledge of how many cache entries there
were.
With the unfortunate result that each slab entry was big enough to hold
every irq.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adam B. Jerome [Wed, 12 Jul 2006 16:03:07 +0000 (09:03 -0700)]
[PATCH] /fs/proc/: 'larger than buffer size' memory accessed by clear_user()
Address a potential 'larger than buffer size' memory access by
clear_user(). Without this patch, this call to clear_user() can attempt to
clear too many (tsz) bytes resulting in a wrong (-EFAULT) return code by
read_kcore().
Signed-off-by: Adam B. Jerome <abj@novell.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arjan van de Ven [Wed, 12 Jul 2006 16:03:06 +0000 (09:03 -0700)]
[PATCH] lockdep: annotate the sysfs i_mutex to be a separate class
sysfs has a different i_mutex lock order behavior for i_mutex than the
other filesystems; sysfs i_mutex is called in many places with subsystem
locks held. At the same time, many of the VFS locking rules do not apply
to sysfs at all (cross directory rename for example). To untangle this
mess (which gives false positives in lockdep), we're giving sysfs inodes
their own class for i_mutex.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When found, it is obvious. nfds calculated when allocating fdsets is
rewritten by calculation of size of fdtable, and when we are unlucky, we
try to free fdsets of wrong size.
Found due to OpenVZ resource management (User Beancounters).
[PATCH] Fix prctl privilege escalation and suid_dumpable (CVE-2006-2451)
Based on a patch from Ernie Petrides
During security research, Red Hat discovered a behavioral flaw in core
dump handling. A local user could create a program that would cause a
core file to be dumped into a directory they would not normally have
permissions to write to. This could lead to a denial of service (disk
consumption), or allow the local user to gain root privileges.
The prctl() system call should never allow to set "dumpable" to the
value 2. Especially not for non-privileged users.
This can be split into three cases:
1) running as root -- then core dumps will already be done as root,
and so prctl(PR_SET_DUMPABLE, 2) is not useful
2) running as non-root w/setuid-to-root -- this is the debatable case
3) running as non-root w/setuid-to-non-root -- then you definitely
do NOT want "dumpable" to get set to 2 because you have the
privilege escalation vulnerability
With case #2, the only potential usefulness is for a program that has
designed to run with higher privilege (than the user invoking it) that
wants to be able to create root-owned root-validated core dumps. This
might be useful as a debugging aid, but would only be safe if the program
had done a chdir() to a safe directory.
There is no benefit to a production setuid-to-root utility, because it
shouldn't be dumping core in the first place. If this is true, then the
same debugging aid could also be accomplished with the "suid_dumpable"
sysctl.
[ALSA] Fix section mismatch errors in ALSA PCI drivers
Fixed 'section mismatch' errors in ALSA PCI drivers:
- removed invalid __devinitdata from pci id tables
- fix/remove __devinit of functions called in suspend/resume
Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Randy Dunlap [Tue, 4 Jul 2006 12:25:26 +0000 (14:25 +0200)]
[ALSA] Fix no mpu401 interface can cause hard freeze
This patch fixes the remaining instances in our tree where a non-
existent mpu401 interface can cause a hard freeze when i/o is issued.
This commit closes Malone #34831.
Bug: https://launchpad.net/distros/ubuntu/+source/linux-source-2.6.15/+bug/34831
patch location:
http://www.kernel.org/git/?p=linux/kernel/git/bcollins/ubuntu-dapper.git;a=commitdiff;h=b422309cdd980cfefe99379796c04e961d3c1544
From: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Adrian Bunk [Thu, 29 Jun 2006 11:22:29 +0000 (13:22 +0200)]
[ALSA] fix the SND_FM801_TEA575X dependencies
CONFIG_SND_FM801=y, CONFIG_SND_FM801_TEA575X=m resulted in the following
compile error:
<-- snip -->
...
LD vmlinux
sound/built-in.o: In function 'snd_fm801_free':
fm801.c:(.text+0x3c15b): undefined reference to 'snd_tea575x_exit'
sound/built-in.o: In function 'snd_card_fm801_probe':
fm801.c:(.text+0x3cfde): undefined reference to 'snd_tea575x_init'
make: *** [vmlinux] Error 1
<-- snip -->
This patch fixes kernel Bugzilla #6458.
Signed-off-by: Adrian Bunk <bunk@stusta.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Eric Sesterhenn [Wed, 12 Apr 2006 10:56:10 +0000 (12:56 +0200)]
[ALSA] Memory leak in sound/pcmcia/pdaudiocf/pdaudiocf.c
if one of the first three CS_CHECKS fails, we goto cs_failed:
In this case parse we donr kfree() parse. Since the the last three
CS_CHECKS might also fail, i moved the kfree() below all the CS_CHECKs
and added one in the error path. This fixes coverity bug id #1099
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This is confirmed to fix a hang due to PCI resource conflicts with
setting up the Cardbus bridge on old laptops with the 440MX chipsets.
Original report by Alessio Sangalli, lspci debugging help by Pekka
Enberg, and trial patch suggested by Daniel Ritz:
"From the docs available i would _guess_ this thing is really similar
to the 82443BX/82371AB combination. at least the SMBus base address
register is hidden at the very same place (32bit at 0x90 in function
3 of the "south" brigde)"
The dang thing is largely undocumented, but the patch was corroborated
by Asit Mallick:
"I am trying to find the register information. 440MX is an integration of
440BX north-bridge without AGP and PIIX4E (82371EB). PIIX4 quirk
should cover the ACPI and SMBus related I/O registers."
and verified to fix the problem by Alessio.
Cc: Daniel Ritz <daniel.ritz-ml@swissonline.ch> Cc: Asit Mallick <asit.k.mallick@intel.com> Cc: Pekka Enberg <penberg@cs.helsinki.fi> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Dmitry Torokhov <dtor_core@ameritech.net> Tested-by: Alessio Sangalli <alesan@manoweb.com> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[S390] path grouping and path verifications fixes.
1. Multipath devices for which SetPGID is not supported are not handled well.
Use NOP ccws for path verification (sans path grouping) when SetPGID is not
supported.
2. Check for PGIDs already set with SensePGID on _all_ paths (not just the
first one) and try to find a common one. Moan if no common PGID can be
found (and use NOP verification). If no PGIDs have been set, use the css
global PGID (as before). (Rationale: SetPGID will get a command reject if
the PGID it tries to set does not match the already set PGID.)
3. Immediately before reboot, issue RESET CHANNEL PATH (rcp) on all chpids. This
will remove the old PGIDs. rcp will generate solicited CRWs which can be
savely ignored by the machine check handler (all other actions create
unsolicited CRWs).
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The module parameters for xpram are not or in a wrong way parsed.
The xpram module uses the module_param_array directive with an int
parameter which causes the kernel to automatically parse the passed
numbers. This will cause errors if arguments are omitted or cause
wrong results if arguments have size qualifiers.
Use module_param_array with charp and parse the arguments later.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
futex_atomic_cmpxchg_inatomic has the same bug as the other
atomic futex operations: the operation needs to be done in the
user address space, not the kernel address space. Add the missing
sacf 256 & sacf 0.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a reg_mutex to prevent unregistering a subchannel before it has been
registered. Since 2.6.17, we've seen oopses in kslowcrw when a device is
found to be not operational during sense id when doing initial device
recognition; it is not clear yet why that particular problem was not (yet)
observed with earlier kernels...
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
[S390] raw_local_save_flags/raw_local_irq_restore type check
Make sure that raw_local_save_flags and raw_local_irq_restore always get an
unsigned long parameter. raw_irqs_disabled should call raw_local_save_flags
instead of local_save_flags.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
__builtin_trap() has the archictecture defined backend in gcc since gcc 3.3.
To make sure the kernel builds with gcc 3.2 as well, use the old style BUG()
statement if compiled with older gcc versions.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: ACPI_DOCK: Initialize the atomic notifier list
ACPI: acpi_os_allocate() fixes
ACPI: SBS: fix initialization, sem2mutex
ACPI: add 'const' to several ACPI file_operations
ACPI: delete some defaults from ACPI Kconfig
ACPI: "Device `[%s]' is not power manageable" make message debug only
ACPI: ACPI_DOCK Kconfig
Revert "Revert "ACPI: dock driver""
ACPI: acpi_os_get_thread_id() returns current
ACPI: ACPICA 20060707
Merge commit master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 of HEAD
* HEAD:
[DCCP]: Fix sparse warnings.
[TCP]: Remove TCP Compound
[BPQ] lockdep: fix false positive
[IPV4] inetpeer: Get rid of volatile from peer_total
[AX.25]: Get rid of the last volatile.
[PATCH] x86_64: Allow oprofile for model P4 models
Add it for P4 model 6 - reported to work and have a similar PMU to
earlier P4s.
Add an p4force=1 module override parameter for future use.
We had a discussion about that earlier - it's a trade off between the
PMU staying compatible or not. I think the force parameter is a
reasonable compromise.
Markus Schoder [Mon, 10 Jul 2006 15:06:06 +0000 (17:06 +0200)]
[PATCH] x86_64: Bring x86-64 ia32 emul in sync with i386 on READ_IMPLIES_EXEC enabling
Currently ia32 binaries behave differently with respect to enabling
READ_IMPLIES_EXEC. On i386 a binary with the exec_stack flag set is
executed with READ_IMPLIES_EXEC enabled as well. The same binary
executes without READ_IMPLIES_EXEC on x86-64.
This causes binaries that work on i386 to fail on x86-64 which goes
somewhat against the whole 32 bit emulation idea.
It has been argued that READ_IMPLIES_EXEC should not be enabled at all
for binaries that have the exec_stack flag. Which is probably a valid
point. However until this is clarified I think x86-64 should behave the
same for ia32 binaries as i386.
The following patch brings x86-64 in sync with i386 for ia32 binaries.
The inclusion of TCP Compound needs to be reverted at this time
because it is not 100% certain that this code conforms to the
requirements of Developer's Certificate of Origin 1.1 paragraph (b).
Signed-off-by: David S. Miller <davem@davemloft.net>
Bpqether is encapsulating AX.25 frames into ethernet frames. There is a
virtual bpqether device paired with each ethernet devices, so it's normal
to pass through dev_queue_xmit twice for each frame which triggers the
locking detector.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: David S. Miller <davem@davemloft.net>
[PATCH] knfsd: nfsd4: add per-operation server stats
Add an nfs4 operations count array to nfsd_stats structure. The count is
incremented in nfsd4_proc_compound() where all the operations are handled
by the nfsv4 server. This count of individual nfsv4 operations is also
entered into /proc filesystem.
Signed-off-by: Shankar Anand<shanand@novell.com> Signed-off-by: Neil Brown <neilb@suse.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arjan van de Ven [Mon, 10 Jul 2006 11:45:42 +0000 (04:45 -0700)]
[PATCH] lockdep: disable lock debugging when kernel state becomes untrusted
Disable lockdep debugging in two situations where the integrity of the
kernel no longer is guaranteed: when oopsing and when hitting a
tainting-condition. The goal is to not get weird lockdep traces that don't
make sense or are otherwise undebuggable, to not waste time.
Lockdep assumes that the previous state it knows about is valid to operate,
which is why lockdep turns itself off after the first violation it reports,
after that point it can no longer make that assumption.
A kernel oops means that the integrity of the kernel compromised; in
addition anything lockdep would report is of lesser importance than the
oops.
All the tainting conditions are of similar integrity-violating nature and
also make debugging/diagnosing more difficult.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently most architectures either always build binfmt_elf32 in the kernel
image or make it a boolean option. Only sparc64 and s390 allow to build it
modularly. This patch turns the option into a boolean aswell because elf
requires various symbols that shouldn't be available to modules. The most
urgent one is tasklist_lock whos export this patch series kills, but there
are others like force_sgi aswell.
Note that sparc doesn't allow a modular 32bit a.out handler either, and
that would be the more useful case as only few people want 32bit sunos
compatibility and 99.9% of all sparc64 users need 32bit linux native elf
support.
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: "David S. Miller" <davem@davemloft.net> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the snsc driver uses force_sig to send init a SIGPWR when the
system overheats. This patch switches it to kill_proc instead which has
the following advantages:
(1) gets rid of one of the last remaining tasklist_lock users
in modular code
(2) simplifies the snsc code significantly
The downside is that an init implementation could in theory block SIGPWR
and it would not get delivered. The sysvinit code used by all major
distributions doesn't do this and blocking this signal in init would be a
rather stupid thing to do.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Switch from register_chrdev() to (register|alloc)_chrdev_region().
- use a cdev. This was intended for original patchset, but was
overlooked.
We use a single cdev for all pins (minor device-numbers), as gleaned
from cs5535_gpio, and in contrast to whats currently done in scx200_gpio
(which I'll fix soon)
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jim Cromie [Mon, 10 Jul 2006 11:45:36 +0000 (04:45 -0700)]
[PATCH] pc8736x_gpio: fix re-modprobe errors: undo region reservation
Fix module-init-func by repairing usage of platform_device_del/put in
module-exit-func. IOW, it imitates Ingo's 'mishaps' patch, which fixed the
module-init-func's undo handling.
Also fixes lack of release_region to undo the earlier registration.
Also starts to 'use a cdev' which was originally intended (its present in
scx200_gpio). Code compiles and runs, exhibits a lesser error than
previously. (re-register-chrdev fails)
Since I had to add "include <linux/cdev.h>", I went ahead and made 2
tweaks that fell into diff-context-window:
- remove include <linux/config.h> everyone's doing it
- copyright updates - current date is 'wrong'
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jim Cromie [Mon, 10 Jul 2006 11:45:35 +0000 (04:45 -0700)]
[PATCH] pc8736x_gpio: fix re-modprobe errors: define and use constants
add constant defines - preparatory patch
- adds #define CONSTs for max-pin, gpio-addr-range (for reserving region)
- fix wrong max-pin check in gpio_open()
- add 'Winbond' to module description. NSC sold the product, Winbond
has supported us / lm-sensors
Signed-off-by: Jim Cromie <jim.cromie@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Chris Boot [Mon, 10 Jul 2006 11:45:34 +0000 (04:45 -0700)]
[PATCH] LED Class support for Soekris net48xx
Add LED Class device support for the Soekris net48xx Error LED. Tested
only on a net4801, but should work on a net4826 as well. I'd love to find
a way of detecting a Soekris net48xx device but there is no DMI or any
Soekris-specific PCI devices.
[akpm@osdl.org: fixlets, cleanups] Signed-off-by: Chris Boot <bootc@bootc.net> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Richard Purdie <rpurdie@rpsys.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Handle memory-mapped chips properly, needed for example on DECstations.
This support was in Linux 2.4 but for some reason got lost in 2.6. This
patch is taken directly from the linux-mips repository.
[akpm@osdl.org: cleanup] Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Signed-off-by: Martin Michlmayr <tbm@cyrius.com> Cc: Paul Gortmaker <penguin@muskoka.com> Cc: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] make valid_mmap_phys_addr_range() take a pfn
Newer ARMs have a 40 bit physical address space, but mapping physical
memory above 4G needs a special page table format which we (currently?) do
not use for userspace mappings, so what happens instead is that mapping an
address >= 4G will happily discard the upper bits and wrap.
There is a valid_mmap_phys_addr_range() arch hook where we could check for
>= 4G addresses and deny the mapping, but this hook takes an unsigned long
address:
static inline int valid_mmap_phys_addr_range(unsigned long addr, size_t size);
And drivers/char/mem.c:mmap_mem() calls it like this:
When EDAC was first introduced into the kernel it had a sysfs interface,
but due to some problems it was disabled in 2.6.16 and remained disabled in
2.6.17.
With feedback, several of the control and attribute files of that interface
had some good constructive feedback. PCI Blacklist/Whitelist was a major
set which has design issues and it has been removed in this patch. Instead
of storing PCI broken parity status in EDAC, it has been moved to the
pci_dev structure itself by a previous PCI patch. A future patch will
enable that feature in EDAC by utilizing the pci_dev info.
The sysfs is now enabled in this patch, with a minimal set of control and
attribute files for examining EDAC state and for enabling/disabling the
memory and PCI operations.
The Documentation for EDAC has also been updated to reflect the new state
of EDAC operation.
Signed-off-by:Doug Thompson <norsk5@xmisson.com> Cc: Greg KH <greg@kroah.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Jones [Mon, 10 Jul 2006 11:45:18 +0000 (04:45 -0700)]
[PATCH] s390: broken null test in claw driver
Whoops, better hope this never gets passed a null dev in its current state.
Signed-off-by: Dave Jones <davej@redhat.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Michael Holzheu <holzheu@de.ibm.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Dave Jones [Mon, 10 Jul 2006 11:45:18 +0000 (04:45 -0700)]
[PATCH] fix oddball boolean logic in s390 netiucv
Signed-off-by: Dave Jones <davej@redhat.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Andreas Herrmann <aherrman@de.ibm.com> Cc: Michael Holzheu <holzheu@de.ibm.com> Acked-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two variables in drivers/s390/net/qeth_main.c:qeth_send_packet() are only
used if CONFIG_QETH_PERF_STATS. Move their definition under the same ifdef
to remove compiler warning.
Signed-off-by: Serge Hallyn <serue@us.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:16 +0000 (04:45 -0700)]
[PATCH] uml: make mconsole version requests happen in a process
Handling a host mconsole version request must be done in a process context
rather than interrupt context now that utsname information can be
process-specific rather than global.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:15 +0000 (04:45 -0700)]
[PATCH] uml: remove unused variable
The dedevfsification of UML left an unused variable behind.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:15 +0000 (04:45 -0700)]
[PATCH] uml: add some EINTR protection
Add some more uses of the CATCH_EINTR wrapper.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:14 +0000 (04:45 -0700)]
[PATCH] uml: formatting fixes
Fix a bunch of formatting problems.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:13 +0000 (04:45 -0700)]
[PATCH] uml: move _kern.c files
Move most *_kern.c files in arch/um/kernel to *.c. This makes UML somewhat
more closely resemble the other arches.
[akpm@osdl.org: use the new INTF_* flags] Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:13 +0000 (04:45 -0700)]
[PATCH] uml: remove syscall debugging
Eliminate an unused debug option.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:12 +0000 (04:45 -0700)]
[PATCH] uml: make some symbols static
A few sigio-related things can be made static.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:11 +0000 (04:45 -0700)]
[PATCH] uml: fix exitcall ordering bug
This fixes an exitcall ordering bug - calls to ignore_sigio_fd can come from
exitcalls that come after the sigio thread has been killed. This would cause
shutdown to hang or crash.
Fixed by having ignore_sigio_fd check that the thread is present before trying
to communicate with it.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:11 +0000 (04:45 -0700)]
[PATCH] uml: remove os_isatty
os_isatty can be made to disappear by moving maybe_sigio_broken from kernel to
user code. This also lets write_sigio_workaround become static.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:10 +0000 (04:45 -0700)]
[PATCH] uml: remove spinlock wrapper functions
The irq_spinlock is not needed from user code any more, so the irq_lock and
irq_unlock wrappers can go away. This also changes the name of the lock to
irq_lock.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:09 +0000 (04:45 -0700)]
[PATCH] uml: mark forward_interrupts as being mode-specific
Mark forward_interrupts as being tt-mode only.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jeff Dike [Mon, 10 Jul 2006 11:45:09 +0000 (04:45 -0700)]
[PATCH] uml: ifdef a mode-specific function
uml_idle_timer is tt-mode only, so ifdef it as such to make it easier to spot
when tt mode is killed.
Signed-off-by: Jeff Dike <jdike@addtoit.com> Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
projects / linux-2.6 / log