There are two problems in the vt220 intialization:
o Currently the vt220 console looses early printk events until the
the vt220 tty is registered.
o console should work if tty_register fails
sclp_vt220_con_init calls __sclp_vt220_init and register_console.
It does not register the driver with the sclp core code via
sclp_register. That results in an sclp_send_mask=0. Therefore,
__sclp_vt220_emit will reject buffers with EIO. Unfortunately
register_console will cause the printk buffer to be sent to the
console and, therefore, every early message gets dropped. The
sclp_send_mask is set later during boot, when sclp_vt220_tty_init
calls sclp_register.
The solution is to move the sclp_register call from sclp_vt220_tty_init
to __sclp_vt220_init. This makes sure that the console is properly
registered with the sclp subsystem before the first log buffer messages
are passed to the vt220 console.
We also adopt the cleanup on error to keep the console alive if
tty_register fails.
Thanks to Peter Oberparleiter and Heiko Carstens for review and ideas
for improvement.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ursula Braun [Sat, 9 Feb 2008 17:24:32 +0000 (18:24 +0100)]
[S390] qdio: avoid hang when establishing qdio queues
If qdio establish runs in parallel with a channel error,
ccw_device_start_timeout may not trigger the qdio_timeout_handler.
In this case neither QDIO_IRQ_STATE_ESTABLISHED nor
QDIO_IRQ_STATE_ERR is reached and the following wait_event hangs
forever.
Solution: do not make use of the timeout option with
ccw_device_start, but add a timeout to the following wait_event.
Signed-off-by: Ursula Braun <braunu@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With the new space saving spinlock_t and a non-debug configuration
the struct page only has 32 bytes for 31 bit s390. The causes an
overflow in the calculation of VMEM_MAX_PHYS which renders the
kernel unbootable.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The black art of inline assemblies.. The new __ffs_word_loop/
__ffz_word_loop inline assemblies need an early clobber for the
two input/output variables.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
David S. Miller [Fri, 16 Nov 2007 10:53:50 +0000 (02:53 -0800)]
[SPARC]: Merge asm-sparc{,64}/bug.h
Note that because of minimum compiler version enforcement in
linux/compiler.h these days the check for sparc32 buggy
__builtin_trap() can be safely removed.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 9 Feb 2008 11:11:01 +0000 (03:11 -0800)]
[SPARC64]: Add SG merging support back into IOMMU code.
Mimicks almost perfectly the powerpc IOMMU code, except that it
doesn't have the IOMMU_PAGE_SIZE != PAGE_SIZE handling, and it also
lacks the device dma mask support bits.
I'll add that later as time permits, but this gets us at least back to
where we were beforehand.
Signed-off-by: David S. Miller <davem@davemloft.net>
Sam Ravnborg [Sat, 9 Feb 2008 09:46:40 +0000 (10:46 +0100)]
ide: introduce HAVE_IDE
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk> Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Sam Ravnborg [Wed, 6 Feb 2008 22:05:33 +0000 (23:05 +0100)]
scsi: fix makefile for aic7(3*x)
Fix bug introduced by my latest fix to the aic7xxx Makefile.
Test build on x86 32 and 64 bit.
Without and with -j (parallel build)
Building firmaware is br0ken with O=... but this
is unrelated to this bug-fix.
Tested-by: Adrian Bunk <bunk@kernel.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Sam Ravnborg [Wed, 6 Feb 2008 20:51:18 +0000 (21:51 +0100)]
kbuild/modpost: improve warnings if symbol is unknown
If we cannot determine the symbol then print
(unknown) to hint the reader that we failed to
find the symbol.
This happens with REL relocation records
in arm object files.
Carlos Corbacho [Sat, 9 Feb 2008 01:32:25 +0000 (01:32 +0000)]
acer-wmi - Add documentation
Add some initial documentation detailing what acer-wmi is, and how to use
it. Update the Kconfig entry with a reference to the documentation.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Len Brown <len.brown@intel.com>
Carlos Corbacho [Sat, 9 Feb 2008 01:32:19 +0000 (01:32 +0000)]
sonypi - Move sonypi.txt to Documentation/laptops
Also update references to sonypi.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> CC: Mattia Dongili <malattia@linux.it> Signed-off-by: Len Brown <len.brown@intel.com>
Carlos Corbacho [Sat, 9 Feb 2008 01:32:14 +0000 (01:32 +0000)]
sony-laptop - Move sony-laptop.txt to Documentation/laptops
Also update references to sony-laptop.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> CC: Mattia Dongili <malattia@linux.it> Signed-off-by: Len Brown <len.brown@intel.com>
Carlos Corbacho [Sat, 9 Feb 2008 01:32:09 +0000 (01:32 +0000)]
thinkpad-acpi - Move thinkpad-acpi.txt to Documentation/laptops
Also update references to thinkpad-acpi.txt in Kconfig.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> CC: Henrique de Moraes Holschuh <hmh@hmh.eng.br> Signed-off-by: Len Brown <len.brown@intel.com>
Carlos Corbacho [Sat, 9 Feb 2008 01:32:03 +0000 (01:32 +0000)]
Documentation - Create laptops sub-directory
There are currently various laptop drivers floating about with no central
place for their documentation, which is currently scattered around the top
level Documentation/ directory.
So, as a first step, lets create a Documentation sub-directory, and update
the relevant index files. The work of then moving the existing laptop
driver related documentation will then be handled later.
Signed-off-by: Carlos Corbacho <carlos@strangeworlds.co.uk> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> CC: Henrique de Moraes Holschuh <hmh@hmh.eng.br> CC: Mattia Dongili <malattia@linux.it> Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sat, 9 Feb 2008 09:01:48 +0000 (04:01 -0500)]
ACPI: thermal: buildfix for CONFIG_THERMAL=n
This fixes the build, but acpi_fan_add() still needs
to be updated to handle thermal_cooling_device_register()
returning NULL as a non-fatal condition.
Venki Pallipadi [Sat, 9 Feb 2008 01:05:44 +0000 (17:05 -0800)]
cpuidle: build fix for non-x86
The last posted version of this patch gave compile error
on IA64. So, here goes yet another rewrite of the patch.
Convert cpu_idle_wait() to cpuidle_kick_cpus() which is
SMP-only, and gives error on non supported CPU.
Changes from last patch sent by Kevin:
Moved the definition of kick_cpus back to cpuidle.c from cpuidle.h:
* Having it in .h gives #error on archs which includes the header file without
actually having CPU_IDLE configured. To make it work in .h, we need one more
#ifdef around that code which makes it messy.
* Also, the function is only called from one file. So, it can be in declared
statically in .c rather than making it available to everyone who includes
the .h file.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com> Signed-off-by: Kevin Hilman <khilman@mvista.com> Signed-off-by: Len Brown <len.brown@intel.com>
Mart Raudsepp [Sat, 9 Feb 2008 08:16:36 +0000 (08:16 +0000)]
[MTD] [NAND] cs553x_nand: command line partitioning support
Implements kernel command line partitioning support for the CS5535/CS5536 chipsets driver.
For that the following is done:
* cs553x_cleanup(): try the cleanup for all chip selects to not leak memory
* Assign a unique name for each chip select to be separately addressable in the command line mtd-id portion(s)
* Use the already defined PIN_OPT_IDE constant where appropriate for readability
* Include command line partitioning support when CONFIG_MTD_PARTS is set
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Nick Piggin [Sat, 9 Feb 2008 00:15:19 +0000 (01:15 +0100)]
mm: special mapping nopage
Convert special mapping install from nopage to fault.
Because the "vm_file" is NULL for the special mapping, the generic VM
code has messed up "vm_pgoff" thinking that it's an anonymous mapping
and the offset does't matter. For that reason, we need to undo the
vm_pgoff offset that got added into vmf->pgoff.
[ We _really_ should clean that up - either by making this whole special
mapping code just use a real file entry rather than that ugly array of
"struct page" pointers, or by just making the VM code realize that
even if vm_file is NULL it may not be a regular anonymous mmap.
- Linus ]
Linus Torvalds [Fri, 8 Feb 2008 23:40:28 +0000 (15:40 -0800)]
Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Fix large MCA bootmem allocation
[IA64] Simplify cpu_idle_wait
[IA64] Synchronize RBS on PTRACE_ATTACH
[IA64] Synchronize kernel RSE to user-space and back
[IA64] Rename TIF_PERFMON_WORK back to TIF_NOTIFY_RESUME
[IA64] Wire up timerfd_{create,settime,gettime} syscalls
Ingo Molnar [Fri, 8 Feb 2008 23:15:06 +0000 (00:15 +0100)]
x86: fix pgtable_t build breakage
Commit 2f569afd9ced9ebec9a6eb3dbf6f83429be0a7b4 ("CONFIG_HIGHPTE vs.
sub-page page tables") caused some build breakage due to pgtable_t only
getting declared in the CONFIG_X86_PAE case.
Linus Torvalds [Fri, 8 Feb 2008 23:34:26 +0000 (15:34 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Remove unused struct ib_device.flags member
IB/core: Add IP checksum offload support
IPoIB: Add send gather support
IPoIB: Add high DMA feature flag
IB/mlx4: Use multiple WQ blocks to post smaller send WQEs
mlx4_core: Clean up struct mlx4_buf
mlx4_core: For 64-bit systems, vmap() kernel queue buffers
IB/mlx4: Consolidate code to get an entry from a struct mlx4_buf
Linus Torvalds [Fri, 8 Feb 2008 23:33:45 +0000 (15:33 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (24 commits)
[Blackfin] arch: import defines for BF547 -- it is just like the BF548, but no CAN
[Blackfin] arch: fix build fails only include header files when enabled
[Blackfin] arch: declare default INSTALL_PATH for Blackfin ports
[Blackfin] arch: Encourage users to use the spidev character driver: Provide platform support
[Blackfin] arch: Enable UART2 and UART3 for bf548
[Blackfin] arch: Enable NET2272 on BF561-EZkit - remove request_mem_region
[Blackfin] arch:Fix BUG [#3876] pfbutton test for BTN3 on bf533 don't show complete info
[Blackfin] arch: remove duplicated definitions of the line discipline numbers N_* in asm-blackfin/termios.h
[Blackfin] arch: fix building with mtd uclinux by putting the mtd_phys option into the function it actually gets used in
[Blackfin] arch: simpler header and update dates
[Blackfin] arch: move the init sections to the end of memory
[Blackfin] arch: change the trace buffer control start/stop logic in the exception handlers
[Blackfin] arch: fix typo in printk message
[Blackfin] arch: this is an ezkit, not a stamp, so fixup the init function name
[Blackfin] arch: add slightly better help text for CPLB_INFO
[Blackfin] arch: Fix BUG - Enable ISP1362 driver to work ok with BF561
[Blackfin] arch: Fix header file information
[Blackfin] arch: Add Support for ISP1362
[Blackfin] arch: add support for cmdline partitioning to the BF533-STAMP flash map driver and enable it as a module by default
[Blackfin] arch: hook up set_irq_wake in Blackfin's irq code
...
Alan Cox [Fri, 8 Feb 2008 23:00:48 +0000 (15:00 -0800)]
x25_asy: Fix ref count rule violation
x25_asy does not take an ldisc reference before calling the flush method.
Fix it to use the helper function we provide.
Signed-off-by: Alan Cox <alan@redhat.com> Cc: Krzysztof Halasa <khc@pm.waw.pl> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jeff Garzik <jeff@garzik.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lib/scatterlist.o needed by a module only - link it in unconditionally
lib/scatterlist.c is needed by drivers/media/video/videobuf-dma-sg.c, and
we would like to be able to use the latter without PCI too, for example, on
PXA270 ARM CPU. It is then possible to create a configuration with
CONFIG_BLOCK=n, where only module code will need scatterlist.c. Therefore
it must be in obj-y.
Adrian Bunk [Fri, 8 Feb 2008 23:00:46 +0000 (15:00 -0800)]
fix xtensa timerfd breakage
In file included from /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/xtensa/kernel/syscall.c:39:
include2/asm/unistd.h:681: error: 'sys_timerfd' undeclared here (not in a function)
Signed-off-by: Adrian Bunk <bunk@kernel.org> Cc: Christian Zankel <chris@zankel.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the FRV cmpxchg_local by breaking the following header dependency loop :
linux/kernel.h -> linux/bitops.h -> asm-frv/bitops.h -> asm-frv/atomic.h
-> asm-frv/system.h ->
asm-generic/cmpxchg_local.h -> typecheck() defined in linux/kernel.h
and
linux/kernel.h -> linux/bitops.h -> asm-frv/bitops.h -> asm-frv/atomic.h ->
asm-generic/cmpxchg_local.h -> typecheck() defined in linux/kernel.h
In order to fix this :
- Move the atomic_test_and_ *_mask inlines from asm-frv/atomic.h (why are they
there at all anyway ? They are not touching atomic_t variables!) to
asm-frv/bitops.h.
Also fix a build issue with cmpxchg : it does not cast to (unsigned long *)
like other architectures, to deal with it in the cmpxchg_local macro.
FRV builds fine with this patch.
Thanks to Adrian Bunk <bunk@kernel.org> for spotting this bug.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca> Cc: Adrian Bunk <bunk@kernel.org> Cc: David Howells <dhowells@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Fri, 8 Feb 2008 23:00:43 +0000 (15:00 -0800)]
revert "proc: fix the threaded proc self"
Revert commit c6caeb7c4544608e8ae62731334661fc396c7f85 ("proc: fix the
threaded /proc/self"), since Eric says "The patch really is wrong.
There is at least one corner case in procps that cares."
Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "Guillaume Chazarain" <guichaz@yahoo.fr> Cc: "Pavel Emelyanov" <xemul@openvz.org> Cc: "Rafael J. Wysocki" <rjw@sisk.pl> Cc: Oleg Nesterov <oleg@tv-sign.ru> Cc: Roland McGrath <roland@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eli Cohen [Wed, 30 Jan 2008 16:30:57 +0000 (18:30 +0200)]
IB/core: Add IP checksum offload support
Add a device capability to show when it can handle checksum offload.
Also add a send flag for inserting checksums and a csum_ok field to
the completion record.
Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eli Cohen [Wed, 30 Jan 2008 16:30:53 +0000 (18:30 +0200)]
IPoIB: Add send gather support
This patch acts as a preparation for using checksum offload for IB
devices capable of inserting/verifying checksum in IP packets. The
patch does not actaully turn on NETIF_F_SG - we defer that to the
patches adding checksum offload capabilities.
We only add support for send gathers for datagram mode, since existing
HW does not support checksum offload on connected QPs.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il> Signed-off-by: Eli Cohen <eli@mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eli Cohen [Wed, 30 Jan 2008 16:30:46 +0000 (18:30 +0200)]
IPoIB: Add high DMA feature flag
All current InfiniBand devices can handle all DMA addresses, and it's
hard to imagine anyone would be silly enough to build a new device
that couldn't. Therefore, enable the NETIF_F_HIGHDMA feature for IPoIB.
This has no effect for no, but is needed when we enable gather/scatter
support and checksum stateless offloads.
Signed-off-by: Eli Cohen <eli@mellnaox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Jack Morgenstein [Mon, 28 Jan 2008 08:40:59 +0000 (10:40 +0200)]
IB/mlx4: Use multiple WQ blocks to post smaller send WQEs
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Roland Dreier <rolandd@cisco.com>
Russ Anderson [Tue, 5 Feb 2008 23:12:32 +0000 (17:12 -0600)]
[IA64] Fix large MCA bootmem allocation
The MCA code allocates bootmem memory for NR_CPUS, regardless
of how many cpus the system actually has. This change allocates
memory only for cpus that actually exist.
On my test system with NR_CPUS = 1024, reserved memory was reduced by 130944k.
Petr Tesarik [Wed, 12 Dec 2007 14:23:34 +0000 (15:23 +0100)]
[IA64] Synchronize kernel RSE to user-space and back
This is base kernel patch for ptrace RSE bug. It's basically a backport
from the utrace RSE patch I sent out several weeks ago. please review.
when a thread is stopped (ptraced), debugger might change thread's user
stack (change memory directly), and we must avoid the RSE stored in
kernel to override user stack (user space's RSE is newer than kernel's
in the case). To workaround the issue, we copy kernel RSE to user RSE
before the task is stopped, so user RSE has updated data. we then copy
user RSE to kernel after the task is resummed from traced stop and
kernel will use the newer RSE to return to user.
Signed-off-by: Shaohua Li <shaohua.li@intel.com> Signed-off-by: Petr Tesarik <ptesarik@suse.cz> CC: Roland McGrath <roland@redhat.com> Signed-off-by: Tony Luck <tony.luck@intel.com>
Tony Lindgren [Wed, 19 Dec 2007 04:58:32 +0000 (20:58 -0800)]
ARM: OMAP1: Misc clean-up
This patch cleans up omap1 files to sync up with linux-omap tree:
- Remove omap-generic MMC config as it should be defined in board-*.c files
instead of using board-generic.c
- New style I2C board_info from David Brownell <dbrownell@users.sourceforge.net>
- Init section fixes from Dirk Behme <dirk.behme@googlemail.com>
Jarkko Nikula [Wed, 7 Nov 2007 04:54:32 +0000 (06:54 +0200)]
ARM: OMAP1: Use I2C bus registration helper for omap1
This patch starts using introduced I2C bus registration helper by cleaning
up registration currently done in various places and by doing necessary
board file modifications.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
Felipe Balbi [Tue, 27 Nov 2007 04:01:45 +0000 (00:01 -0400)]
ARM: OMAP1: Make omap1 use MMC multislot structures
Make omap1 use new MMC multislot structures. The related MMC
patches will be sent separately.
Signed-off-by: Felipe Balbi <felipe.lima@indt.org.br> Signed-off-by: Anderson Briglia <anderson.briglia@indt.org.br> Signed-off-by: Carlos Eduardo Aguiar <carlos.aguiar@indt.org.br> Signed-off-by: David Cohen <david.cohen@indt.org.br> Signed-off-by: Eduardo Valentin <eduardo.valentin@indt.org.br> Signed-off-by: Tony Lindgren <tony@atomide.com>
Tony Lindgren [Tue, 11 Dec 2007 21:50:17 +0000 (13:50 -0800)]
ARM: OMAP1: Make omap1 boards to use omap_nand_platform_data
This patch adds omap_nand_platform data based on a patch
by Shahrom Sharif-Kashani <sshahrom@micron.com>, and makes
omap1 boards to use omap_nand_platform_data instead of
nand_platform_data used earlier.
Jarkko Nikula [Wed, 7 Nov 2007 04:54:31 +0000 (06:54 +0200)]
ARM: OMAP: Add helper module for board specific I2C bus registration
This helper module simplifies I2C bus registration for different OMAP
platforms by doing registration in one place only and to allow board
specific bus configuration like clock rate and number of busses configured.
Helper should cover OMAP processors from first to third generation.
This patch just adds the feature and current implementation cleanup and
board file modifications will be done in following patches.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap3430 CPU identification macros.
Silicon revision check macros added by Girish S G <girishsg@ti.com>.
CPU identification macro and silicon revision check macros
cleaned up by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com> Signed-off-by: Girish S G <girishsg@ti.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
Linus Torvalds [Fri, 8 Feb 2008 18:01:28 +0000 (10:01 -0800)]
Merge branch 'cris' of git://www.jni.nu/cris
* 'cris' of git://www.jni.nu/cris: (158 commits)
CRIS v32: Remove hwregs/timer_defs.h, it is now architecture specific.
CRIS v32: Change drivers/i2c.c locking.
CRIS v32: Rewrite ARTPEC-3 gpio driver to avoid volatiles and general cleanup.
CRIS: Add new timerfd syscall entries.
MAINTAINERS: Add my information for the CRIS port.
CRIS v32: Correct spelling of bandwidth in function name.
CRIS v32: Clean up nandflash.c for ARTPEC-3 and ETRAX FS.
CRIS v10: Cleanup of drivers/gpio.c
CRIS v10: drivers/net/cris/eth_v10.c rename LED defines to CRIS_LED to avoid name clash.
CRIS: Make io_pwm_set_period members unsigned in etraxgpio.h
CRIS: Move ETRAX_AXISFLASHMAP to common Kconfig file.
CRIS: Drop regs parameter from call to profile_tick in kernel/time.c
CRIS v32: Fix minor formatting issue in mach-a3/io.c
CRIS v32: Initialize GIO even if we're rambooting in kernel/head.S
CRIS v32: Remove kernel/arbiter.c, it now exists in machine dependent directory.
CRIS v32: Minor changes to avoid errors in asm-cris/arch-v32/hwregs/reg_rdwr.h
CRIS v32: arch-v32/hwregs/intr_vect_defs.h moved to machine dependent directory.
CRIS v32: Correct offset for TASK_pid in asm-cris/arch-v32/offset.h
CRIS v32: Move register map header to machine dependent directory.
CRIS v32: Let compiler know that memory is clobbered after a break op.
...